Benutzeranleitung / Produktwartung DragStar XVS125 (2003) des Produzenten Yamaha
Zur Seite of 78
5JX-28199-E3 XVS125 PRINTED ON RECYCLED P APER Y AMAHA MOTOR CO. , L TD. PRINTED IN JAP AN 2003.6–0.1 × 1 ! (E) OWNER’S MANUAL 5JX-9-E3_hyoushi 5/30/03 8:36 AM Page 1.
INTRODUCTION EAU10100 Welcome to the Yamaha world of motorcycling! As the owner of the XVS125, you are benefiting from Yamaha’s vast experience and newest technology regarding the design and manufacture of high-quality products, which have earned Yamaha a reputation for dependability.
IMPORTANT MANUAL INFORMATION EAU10150 Particularly important information is distinguished in this manual by the following notations: NO TE: ● This manual should be considered a permanent part of this motorcycle and should remain with it even if the motorcycle is subsequently sold.
IMPORTANT MANUAL INFORMATION EAU10200 XVS125 O WNER’S MANU AL ©2003 by Y amaha Motor Co., Ltd. 1st edition, May 2003 All rights reserved. Any reprinting or unauthorized use without the written permission of Y amaha Motor Co., Ltd. is expressl y prohibited.
TABLE OF CONTENTS SAFETY INFORMATION ............. 1-1 DESCRIPTION ............................. 2-1 Left view ..................................... 2-1 Right view ................................... 2-2 Controls and instruments ........... 2-3 INSTRUMENT AND CONTROL FUNCTIONS .
TABLE OF CONTENTS Checking and lubricating the brake and clutch levers ......... 6-24 Checking and lubricating the sidestand ............................... 6-25 Checking the front fork ............ 6-25 Checking the steering ............. 6-26 Checking the wheel bearings .
1-1 1 SAFETY INFORMATION EAU10250 MOTORCYCLES ARE SINGLE TRACK VEHICLES. THEIR SAFE USE AND OPERATION ARE DEPEN- DENT UPON THE USE OF PROPER RIDING TECHNIQUES AS WELL AS THE EXPERTISE OF THE OPERA- TOR. EVERY OPERATOR SHOULD KNOW THE FOLLOWING REQUIRE- MENTS BEFORE RIDING THIS MO- TORCYCLE.
SAFETY INFORMATION 1-2 1 wide on a turn due to EXCESSIVE SPEED or undercornering (insuffi- cient lean angle for the speed). ● Always obey the speed limit and never travel faster than warrant- ed by road and traffic conditions. ● Always signal before turning or changing lanes.
SAFETY INFORMATION 1-3 1 sories to your motorcycle: Loading The total weight of the operator, pas- senger, accessories and cargo must not exceed the maximum load limit of 183.0 kg (404 lb). When loading within this weight limit, keep the following in mind: ● Cargo and accessory weight should be kept as low and close to the motorcycle as possible.
SAFETY INFORMATION 1-4 1 not recommended. ● Use caution when adding electri- cal accessories. If electrical acces- sories exceed the capacity of the motorcycle’s electrical system, an electric failure could result, which could cause a dangerous loss of lights or engine power.
2-1 1 2 3 4 5 6 7 8 9 DESCRIPTION EAU10410 Left view 12 3 4 5 6 1. Headlight (page 6-29) 2. Fuel cock (page 3-7) 3. Fuses (page 6-28) 4. Helmet holder (page 3-9) 5.
DESCRIPTION 2-2 2 3 4 5 6 7 8 9 EAU10420 Right view 12 3 4 5 6 1. Owner’ s tool kit (page 6-1) 2. Batter y (page 6-27) 3. Air filter element (page 6-10) 4.
DESCRIPTION 2-3 1 2 3 4 5 6 7 8 9 EAU10430 Controls and instruments 1 2 3 4 5 6 7 8 1. Clutch lev er (page 3-4) 2. Left handlebar switches (page 3-3) 3. Speedometer unit (page 3-2) 4. Right handlebar switches (page 3-3) 5. Brake le ver (page 3-5) 6. Throttle grip (page 6-12) 7.
INSTRUMENT AND CONTROL FUNCTIONS 3-1 2 3 4 5 6 7 8 9 EAU10460 Main switch/steering lock The main switch/steering lock controls the ignition and lighting systems, and is used to lock the steering. The various positions are described below. EAU10630 ON All electrical systems are supplied with power, and the engine can be started.
INSTRUMENT AND CONTROL FUNCTIONS 3-2 1 2 3 4 5 6 7 8 9 EAU11001 Indicator and warning lights EAU11020 Turn signal indicator light “” This indicator light flashes when the turn signal switch is pushed to the left or right. EAU11060 Neutral indicator light “” This indicator light comes on when the transmission is in the neutral position.
INSTRUMENT AND CONTROL FUNCTIONS 3-3 2 3 4 5 6 7 8 9 NO TE: Only for the German model equipped with a speed limiter: The speed limiter prevents the vehi- cle from exceeding a riding speed of 80 km/h. EAU12330 Anti-theft alarm (optional) This model can be equipped with an optional anti-theft alarm by a Yamaha dealer.
INSTRUMENT AND CONTROL FUNCTIONS 3-4 1 2 3 4 5 6 7 8 9 Right EAU12350 Pass switch “” Press this switch to flash the headlight. EAU12400 Dimmer switch “ / ” Set this switch to “” for the high beam and to “” for the low beam. EAU12460 Turn signal switch “ / ” To signal a right-hand turn, push this switch to “” .
INSTRUMENT AND CONTROL FUNCTIONS 3-5 2 3 4 5 6 7 8 9 EAU12870 Shift pedal The shift pedal is located on the left side of the engine and is used in com- bination with the clutch lever when shifting the gears of the 5-speed con- stant-mesh transmission equipped on this motorcycle.
INSTRUMENT AND CONTROL FUNCTIONS 3-6 1 2 3 4 5 6 7 8 9 EAU13000 Fuel tank cap To remove the fuel tank cap Insert the key into the lock and turn it 1/ 4 turn clockwise. The lock will be re- leased and the fuel tank cap can be re- moved. To install the fuel tank cap 1.
INSTRUMENT AND CONTROL FUNCTIONS 3-7 2 3 4 5 6 7 8 9 fuel may deteriorate painted surfac- es or plastic parts. EAU13320 CAUTION: ECA11400 Use only unleaded gasoline. The use of leaded gasoline will cause severe damage to internal engine parts, such as the valves and piston rings, as well as to the exhaust system.
INSTRUMENT AND CONTROL FUNCTIONS 3-8 1 2 3 4 5 6 7 8 9 RES This indicates reserve. With the fuel cock lever in this position, the fuel re- serve is made available. Quickly turn the fuel cock lever to this position if you run out of fuel while riding, otherwise the engine may stall and will have to be primed (see “ PRI ” ).
INSTRUMENT AND CONTROL FUNCTIONS 3-9 2 3 4 5 6 7 8 9 EAU14280 Helmet holder To open the helmet holder, insert the key into the lock, and then turn the key as shown. To lock the helmet holder, place it in the original position, and then remove the key.
INSTRUMENT AND CONTROL FUNCTIONS 3-10 1 2 3 4 5 6 7 8 9 EAU15300 Sidestand The sidestand is located on the left side of the frame. Raise the sidestand or lower it with your foot while holding the vehicle upright. NO TE: The built-in sidestand switch is part of the ignition circuit cut-off system, which cuts the ignition in certain situations.
INSTRUMENT AND CONTROL FUNCTIONS 3-11 2 3 4 5 6 7 8 9 With the engine turned off: 1. Mov e the sidestand down. 2. Make sure that the engine stop s witch is tur ned on. 3. T ur n the ke y on. 4. Shift the transmission into the neutral position. 5. Push the star t switch.
4-1 1 2 3 4 5 6 7 8 9 PRE-OPERATION CHECKS EAU15591 The condition of a vehicle is the owner’s responsibility. Vital components can start to deteriorate quickly and unexpectedly, even if the vehicle remains unused (for example, as a result of exposure to the elements).
PRE-OPERATION CHECKS 4-2 2 3 4 5 6 7 8 9 EAU15601 Pre-operation check list ITEM CHECKS P AGE Fuel ● Check fuel le vel in fuel tank. ● Refuel if necessary . ● Check fuel line f or leakage. 3-6 Engine oil ● Check oil le vel in engine. ● If necessary , add recommended oil to specified lev el.
PRE-OPERATION CHECKS 4-3 1 2 3 4 5 6 7 8 9 Drive chain ● Check chain slac k. ● Adjust if necessary . ● Check chain condition. ● Lubricate if necessar y . 6-21, 6-23 Wheels and tires ● Check f or damage. ● Check tire condition and tread depth.
OPERATION AND IMPORTANT RIDING POINTS 5-1 2 3 4 5 6 7 8 9 EAU15950 W ARNING EWA10270 ● Become thoroughly familiar with all operating controls and their functions before riding. Consult a Yamaha dealer re- garding any control or function that you do not thoroughly un- derstand.
OPERATION AND IMPORTANT RIDING POINTS 5-2 1 2 3 4 5 6 7 8 9 7. When the engine is warm, turn the starter (choke) off. NO TE: The engine is warm when it responds normally to the throttle with the starter (choke) turned off.
OPERATION AND IMPORTANT RIDING POINTS 5-3 2 3 4 5 6 7 8 9 CAUTION: ECA10260 ● Even with the transmission in the neutral position, do not coast for long periods of time with the engine off, and do not tow the motorcycle for long dis- tances. The transmission is properly lubricated only when the engine is running.
OPERATION AND IMPORTANT RIDING POINTS 5-4 1 2 3 4 5 6 7 8 9 EAU16830 Engine break-in There is never a more important period in the life of your engine than the period between 0 and 1,000 km (600 mi). For this reason, you should read the follow- ing material carefully.
PERIODIC MAINTENANCE AND MINOR REPAIR 6-1 2 3 4 5 6 7 8 9 EAU17240 Safety is an obligation of the owner. Pe- riodic inspection, adjustment and lubri- cation will keep your vehicle in the safest and most efficient condition pos- sible. The most important points of in- spection, adjustment, and lubrication are explained on the following pages.
PERIODIC MAINTENANCE AND MINOR REPAIR 6-2 1 2 3 4 5 6 7 8 9 EAU17710 Periodic maintenance and lubrication chart NO TE: ● The annual checks must be performed every year, except if a kilometer-based maintenance is performed in- stead. ● From 30,000 km, repeat the maintenance intervals starting from 6,000 km.
PERIODIC MAINTENANCE AND MINOR REPAIR 6-3 2 3 4 5 6 7 8 9 9* Wheels ● Check runout, spoke tightness and f or damage. ● Tighten spokes if necessary . √ √ √ √ 10 * Tires ● Check tread depth and f or damage. ● Replace if necessary . ● Check air pressure .
PERIODIC MAINTENANCE AND MINOR REPAIR 6-4 1 2 3 4 5 6 7 8 9 EAU18660 NO TE: ● The air filter needs more frequent service if you are riding in unusually wet or dusty areas. ● Hydraulic brake service ● Regularly check and, if necessary, correct the brake fluid level.
PERIODIC MAINTENANCE AND MINOR REPAIR 6-5 2 3 4 5 6 7 8 9 EAU18770 Removing and installing panels The panels shown above need to be re- moved to perform some of the mainte- nance jobs described in this chapter. Refer to this section each time a panel needs to be removed and installed.
PERIODIC MAINTENANCE AND MINOR REPAIR 6-6 1 2 3 4 5 6 7 8 9 2. Pull the rear of the panel out with the key inserted in the lock, and then slide the panel forward to re- lease it in the front. To install the panel 1. Secure the front of the panel, and then push the rear of the panel in with the key inserted in the lock.
PERIODIC MAINTENANCE AND MINOR REPAIR 6-7 2 3 4 5 6 7 8 9 To check the spark plugs 1. Check that the porcelain insulator around the center electrode on each spark plug is a medi- um-to-light tan (the ideal color when the vehicle is ridden normal- ly).
PERIODIC MAINTENANCE AND MINOR REPAIR 6-8 1 2 3 4 5 6 7 8 9 EAU19751 Engine oil and oil filter element The engine oil level should be checked before each ride. In addition, the oil must be changed and the oil filter ele- ment replaced at the intervals specified in the periodic maintenance and lubri- cation chart.
PERIODIC MAINTENANCE AND MINOR REPAIR 6-9 2 3 4 5 6 7 8 9 not being replaced. 4. Remove the oil filter element cover by removing the bolts. 5. Remove and replace the oil filter element and O-ring. 6. Install the oil filter element cover by installing the bolts, then tightening them to the specified torque.
PERIODIC MAINTENANCE AND MINOR REPAIR 6-10 1 2 3 4 5 6 7 8 9 for several minutes while checking it for oil leakage. If oil is leaking, im- mediately turn the engine off and check for the cause. 10. Turn the engine off, and then check the oil level and correct it if necessary.
PERIODIC MAINTENANCE AND MINOR REPAIR 6-11 2 3 4 5 6 7 8 9 out with compressed air as shown. If the air filter element is damaged, replace it. 5. Install the air filter element by in- serting it into the air filter case, then installing the screws.
PERIODIC MAINTENANCE AND MINOR REPAIR 6-12 1 2 3 4 5 6 7 8 9 EAU21340 Adjusting the engine idling speed The engine idling speed must be checked and, if necessary, adjusted as follows at the intervals specified in the periodic maintenance and lubrication chart.
PERIODIC MAINTENANCE AND MINOR REPAIR 6-13 2 3 4 5 6 7 8 9 EAU21400 Adjusting the valve clearance The valve clearance changes with use, resulting in improper air-fuel mixture and/or engine noise.
PERIODIC MAINTENANCE AND MINOR REPAIR 6-14 1 2 3 4 5 6 7 8 9 overloaded motorcycle may re- sult in tire damage, loss of con- trol, or severe injury. Make sure that the total weight of rider, passenger, cargo, and accesso- ries does not exceed the speci- fied maximum load for the vehicle.
PERIODIC MAINTENANCE AND MINOR REPAIR 6-15 2 3 4 5 6 7 8 9 W ARNING EWA10570 ● Have a Yamaha dealer replace excessively worn tires. Besides being illegal, operating the mo- torcycle with excessively worn tires decreases riding stability and can lead to loss of control.
PERIODIC MAINTENANCE AND MINOR REPAIR 6-16 1 2 3 4 5 6 7 8 9 EAU22040 Adjusting the clutch lever free play The clutch lever free play should mea- sure 5.0–10.0 mm (0.20–0.39 in) as shown. Periodically check the clutch le- ver free play and, if necessary, adjust it as follows.
PERIODIC MAINTENANCE AND MINOR REPAIR 6-17 2 3 4 5 6 7 8 9 EAU22091 Adjusting the brake lever free play The brake lever free play should mea- sure 5.0–8.0 mm (0.20–0.31 in) as shown. Periodically check the brake le- ver free play and, if necessary, adjust it as follows.
PERIODIC MAINTENANCE AND MINOR REPAIR 6-18 1 2 3 4 5 6 7 8 9 pedal. 2. To raise the brake pedal, turn the adjusting bolt in direction (a). To lower the brake pedal, turn the ad- justing bolt in direction (b). 3. Tighten the locknut. W ARNING EWA11230 After adjusting the brake pedal posi- tion, the brake pedal free play must be adjusted.
PERIODIC MAINTENANCE AND MINOR REPAIR 6-19 2 3 4 5 6 7 8 9 EAU22270 Adjusting the rear brake light switch The rear brake light switch, which is ac- tivated by the brake pedal, is properly adjusted when the brake light comes on just before braking takes effect.
PERIODIC MAINTENANCE AND MINOR REPAIR 6-20 1 2 3 4 5 6 7 8 9 EAU32341 Checking the brake fluid level Front brake Insufficient brake fluid may allow air to enter the brake system, possibly caus- ing it to become ineffective. Before riding, check that the brake fluid is above the minimum level mark and replenish if necessary.
PERIODIC MAINTENANCE AND MINOR REPAIR 6-21 2 3 4 5 6 7 8 9 EAU22720 Changing the brake fluid Have a Yamaha dealer change the brake fluid at the intervals specified in the NOTE after the periodic mainte- nance and lubrication chart.
PERIODIC MAINTENANCE AND MINOR REPAIR 6-22 1 2 3 4 5 6 7 8 9 2. To tighten the drive chain, turn the adjusting nut at each end of the swingarm in direction (a). To loos- en the drive chain, turn the adjust- ing nut at each end of the swingarm in direction (b), and then push the rear wheel forward.
PERIODIC MAINTENANCE AND MINOR REPAIR 6-23 2 3 4 5 6 7 8 9 EAU23020 Lubricating the drive chain The drive chain must be cleaned and lubricated at the intervals specified in the periodic maintenance and lubrica- tion chart, otherwise it will quickly wear out, especially when riding in dusty or wet areas.
PERIODIC MAINTENANCE AND MINOR REPAIR 6-24 1 2 3 4 5 6 7 8 9 EAU23110 Checking and lubricating the throttle grip and cable The operation of the throttle grip should be checked before each ride. In addi- tion, the cable should be lubricated or replaced at the intervals specified in the periodic maintenance chart.
PERIODIC MAINTENANCE AND MINOR REPAIR 6-25 2 3 4 5 6 7 8 9 EAU23200 Checking and lubricating the sidestand The operation of the sidestand should be checked before each ride, and the sidestand pivot and metal-to-metal contact surfaces should be lubricated if necessary.
PERIODIC MAINTENANCE AND MINOR REPAIR 6-26 1 2 3 4 5 6 7 8 9 EAU23280 Checking the steering Worn or loose steering bearings may cause danger. Therefore, the operation of the steering must be checked as fol- lows at the intervals specified in the pe- riodic maintenance and lubrication chart.
PERIODIC MAINTENANCE AND MINOR REPAIR 6-27 2 3 4 5 6 7 8 9 EAU23380 Battery The battery is located behind panel B. (See page 6-5.) This model is equipped with a sealed-type (MF) battery, which does not require any maintenance. There is no need to check the electrolyte or to add distilled water.
PERIODIC MAINTENANCE AND MINOR REPAIR 6-28 1 2 3 4 5 6 7 8 9 CAUTION: ECA10630 ● Always keep the battery charged. Storing a discharged battery can cause permanent battery damage. ● To charge a sealed-type (MF) battery, a special (constant-volt- age) battery charger is required.
PERIODIC MAINTENANCE AND MINOR REPAIR 6-29 2 3 4 5 6 7 8 9 age rating than recommended to avoid causing extensive damage to the electrical system and possibly a fire. 3. Turn the key to “ON” and turn on the electrical circuit in question to check if the device operates.
PERIODIC MAINTENANCE AND MINOR REPAIR 6-30 1 2 3 4 5 6 7 8 9 W ARNING EWA10790 Headlight bulbs get very hot. There- fore, keep flammable products away from a lit headlight bulb, and do not touch the bulb until it has cooled down. 4. Place a new headlight bulb into po- sition, and then secure it with the bulb holder.
PERIODIC MAINTENANCE AND MINOR REPAIR 6-31 2 3 4 5 6 7 8 9 3. Insert a new bulb into the socket, push it in, and then turn it clock- wise until it stops. 4. Install the lens by installing the screws. CAUTION: ECA10680 Do not overtighten the screws, oth- erwise the lens may break.
PERIODIC MAINTENANCE AND MINOR REPAIR 6-32 1 2 3 4 5 6 7 8 9 EAU24350 Supporting the motorcycle Since this model is not equipped with a centerstand, follow these precautions when removing the front and rear wheel or performing other maintenance requiring the motorcycle to stand up- right.
PERIODIC MAINTENANCE AND MINOR REPAIR 6-33 2 3 4 5 6 7 8 9 3. Lift the front wheel off the ground according to the procedure on page 6-32. 4. Pull the wheel axle out, and then remove the wheel. CAUTION: ECA11070 Do not apply the brake after the wheel has been removed together with the brake disc, otherwise the brake pads will be forced shut.
PERIODIC MAINTENANCE AND MINOR REPAIR 6-34 1 2 3 4 5 6 7 8 9 several times to check for proper fork operation. 8. Connect the speedometer cable. EAU25080 Rear wheel EAU25430 To remove the rear wheel W ARNING EWA10820 ● It is advisable to have a Yamaha dealer service the wheel.
PERIODIC MAINTENANCE AND MINOR REPAIR 6-35 2 3 4 5 6 7 8 9 6. Remove the axle nut, and then pull the wheel axle out. 7. Push the wheel forward, and then remove the drive chain from the rear sprocket. NO TE: The drive chain does not need to be disassembled in order to remove and install the wheel.
PERIODIC MAINTENANCE AND MINOR REPAIR 6-36 1 2 3 4 5 6 7 8 9 EAU25850 Troubleshooting Although Yamaha motorcycles receive a thorough inspection before shipment from the factory, trouble may occur dur- ing operation. Any problem in the fuel, compression, or ignition systems, for example, can cause poor starting and loss of power.
PERIODIC MAINTENANCE AND MINOR REPAIR 6-37 2 3 4 5 6 7 8 9 EAU25891 Troubleshooting chart W ARNING EWA10840 Keep away open flames and do not smoke while checking or working on the fuel system. Check the fuel level in the fuel tank. 1. Fuel There is enough fuel.
7-1 1 2 3 4 5 6 7 8 9 MOTORCYCLE CARE AND STORAGE EAU26040 Care While the open design of a motorcycle reveals the attractiveness of the tech- nology, it also makes it more vulnera- ble. Rust and corrosion can develop even if high-quality components are used.
MOTORCYCLE CARE AND STORAGE 7-2 2 3 4 5 6 7 8 9 any marks. If the windshield is scratched, use a quality plastic polishing compound after washing. After normal use Remove dirt with warm water, a mild detergent, and a soft, clean sponge, and then rinse thoroughly with clean water.
MOTORCYCLE CARE AND STORAGE 7-3 1 2 3 4 5 6 7 8 9 and cornering behavior. CAUTION: ECA10800 ● Apply spray oil and wax spar- ingly and make sure to wipe off any excess. ● Never apply oil or wax to any rubber and plastic parts, but treat them with a suitable care product.
MOTORCYCLE CARE AND STORAGE 7-4 2 3 4 5 6 7 8 9 from the spark plugs, and then install the spark plugs and the spark plug caps. W ARNING EWA10950 To prevent damage or injury from sparking, make sure to ground the spark plug electrodes while turning the engine over.
8-1 1 2 3 4 5 6 7 8 9 SPECIFICATIONS EAU26333 Dimensions: Overall length: 2320 mm (91.3 in) Overall width: 910 mm (35.8 in) Overall height: 1075 mm (42.3 in) Seat height: 670 mm (26.4 in) Wheelbase: 1530 mm (60.2 in) Ground clearance: 150 mm (5.91 in) Minimum turning radius: 2900 mm (114.
SPECIFICATIONS 8-2 2 3 4 5 6 7 8 9 3rd: 29/23 (1.261) 4th: 26/26 (1.000) 5th: 23/27 (0.852) Chassis: Frame type: Double cradle Caster angle: 35.0 ° Trail: 135.
SPECIFICATIONS 8-3 1 2 3 4 5 6 7 8 9 Battery: Model: GT6B-3 Voltage, capacity: 12 V, 6.0 Ah Headlight: Bulb type: Halogen bulb Bulb voltage, wattage x quantity: Headlight: 12 V, 60.0 W/55.0 W × 1 Tail/brake light: 12 V, 5.0 W/21.0 W × 1 Front turn signal light: 12 V, 21.
CONSUMER INFORMATION 9-1 2 3 4 5 6 7 8 9 EAU26351 Identification numbers Record the key identification number, vehicle identification number and mod- el label information in the spaces pro- vided below for assistance when ordering spare parts from a Yamaha dealer or for reference in case the vehi- cle is stolen.
CONSUMER INFORMATION 9-2 1 2 3 4 5 6 7 8 9 EAU26460 Model label The model label is affixed to the loca- tion shown. Record the information on this label in the space provided. This in- formation will be needed when ordering spare parts from a Yamaha dealer.
5JX-28199-E3 XVS125 PRINTED ON RECYCLED P APER Y AMAHA MOTOR CO. , L TD. PRINTED IN JAP AN 2003.6–0.1 × 1 ! (E) OWNER’S MANUAL 5JX-9-E3_hyoushi 5/30/03 8:36 AM Page 1.
Ein wichtiger Punkt beim Kauf des Geräts Yamaha DragStar XVS125 (2003) (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Yamaha DragStar XVS125 (2003) noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Yamaha DragStar XVS125 (2003) - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Yamaha DragStar XVS125 (2003) reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Yamaha DragStar XVS125 (2003) erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Yamaha DragStar XVS125 (2003) besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Yamaha DragStar XVS125 (2003) verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Yamaha DragStar XVS125 (2003). Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Yamaha DragStar XVS125 (2003) gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
