Benutzeranleitung / Produktwartung 8203 des Produzenten Wilton
Zur Seite of 32
This Manual is Bookmarked Operating Instructions — Parts Manual 14-Inch V ertical Band Saws Models: 8201, 8203, 8201VS and 8203VS WHM TOOL GROUP 2420 V antage Drive Elgin, Illinois 60123 Part No. 9078171 Ph.: 800-274-6848 Revision C2 04/07 www .wmhtoolgroup.
.
3 T able of Content s Cover Page .................................................................................................. 1 General Specifications ................................................................................. 4 Operating Precautions .
4 Wilton’s 14-inch T radesman V ertical Band Saws are specially designed to effectively cut a variety of materials including wood, plastic, bakelite, com- posites, ferrous and non-ferrous metals. Models 8201 and 8203 are wood and metal cutting band saws.
5 - Always follow instructions in Operating Instruc- tions and Parts Manual when changing acces- sory tools or parts. - Never modify the machine without consulting Wilton Corporation. Y ou - the St ationary Power T ool User - Hold the Key to Safety . Read and follow these simple rules for best results and full benefits from your machine.
6 safe by using padlocks, master switches, or by removing starter keys. Conductor Length A WG (American Wire Gauge) Number 240 V olt Lines 120 V olt Lines 0 - 50 Feet No. 14 No. 14 50 - 100 Feet No. 14 No. 12 Over 100 Feet No. 12 No. 8 Safety Instructions on Sawing Systems B C D 8.
7 Upper blade guide and support assembly ON/OFF switch Optional rip fence Miter slot T able Lower blade guide and support assembly Lower drive wheel Upper blade guide support assembly Blade guard Lowe.
8 6. T ension the belts (refer to Changing Drive Belt Position) . 7. Check gearbox fluid level in sight gauge. If required, add lubricant to bring level halfway up the sight gauge. (T wo containers of Shell S pirax 90 HD gear oil are packed with the saw .
9 Installing Optional Frame Riser NOTE: Refer to the illustrations in the Replacement Parts section for location of the p arts used on the frame riser . 1. Remove the saw blade (refer to Changing Saw Blades). 2. Remove the two screws at the top and bottom of the blade guide that holds the blade guide on the frame.
10 Operating Controls ST ART/ST OP Switch The ST ART/ST OP switch (refer to Figure 5) is used to turn on the band saw drive motor . The ST ART switch has a molded guard which prevent inadvertent pressing of the ST AR T pushbutton. The STOP pushbutton is not guarded to allow use as an E-stop in an emergency .
11 Adjustments Adjusting Blade Support/Guide Height The upper blade support and guide mechanism can be adjusted to accomodate the height of the work piece. 1. T o adjust the support, loosen the knob that clamps the support rod, then move the support up or down in its holder .
12 breaker in the branch circuit. 2. Move the upper blade guide assembly to the very top of its travel. 3. Make sure the blade is straight, and fully tensioned. (A damaged or worn blade may provide a poor reference surface for squaring the table.) 4. Loosen the table lock knobs and hold the table firmly against it s positive leveling stop.
13 1. T urn the main switch to off. 2. Pull the door open on the pulley case. 3. T urn the clutch handle clockwise and push in, to engage the high speed pulley drive. Or , turn the clutch handle clockwise, and pull out, to engage the reduction gearbox drive.
14 10. Install the belts as required (refer to Figure 10). 1 1. Release the weight of motor so the motor pivots downward. The weight of the motor will provide adequate belt tension. 12. The weight of the motor should provide sufficient tension so the the middle of the small drive belt is displaced approximately the thickness of the belt.
15 9. USING LEA THER GLOVES AND ANSI Z87.1 EYEWEAR TO PROTECT YOURSELF FROM THE CUTTING BLADE, carefully remove the blade from the drive wheels. Remove the blade out of the saw table through the table. 10. Hang the removed blade in a safe place. NOTE: Clean out the interior of the saw with a shop vacuum.
16 Carbide guide block Blade Blade support bearing Guide block set screws Support bearing shaft Guide block support set screw Figure 14. Lower Blade Support Assembly Replacing drive wheel rubber protectors The rubber rings that cover the drive wheels are called protectors.
17 Periodic Maintenance Maintenance Replace blade when teeth are broken Replace blade when bent — or worn — Use a wider blade for more accurate straight cuts Interval Whenever operating saw Whenev.
18 T roubleshooting Fault Excessive blade breakage Premature blade dulling Bad cuts (out-of-square) Bad cuts (rough) Probable cause 1. Material loose in vise. 2. Incorrect speed or feed. 3. T eeth too coarse for material. 4. Incorrect blade tension. 5.
19 1. Blade is binding in the cut. 2. Blade tension too high. 1. Blade guides worn 2. Blade guide bearings not adjusted. 3. Blade guide bearing bracket is loose. 1. Blade tooth pitch too coarse for workpiece. 2. Feed too slow; feed too fast. 3. Workpiece vibrating.
20 Exploded View and Part s Listing – Base – Models 8201, 8203, 8201VS and 8203VS R ef Part. No. Number Description Qt y 1 5513834 Base 1 2 5513835 Door 1 3 5513836 Lock (Ref. Note 1) 1 4 5513837 W asher (Ref. Note 1) 1 5 5513838 Bolt, Pan Head (M4x5) 2 (Ref.
21 Exploded View – Saw Head – Models 8201, 8203, 8201VS, and 8203VS.
22 Re f Part. No. Number Description Qty 1 578251 1 Upper Arm, Frame 1 2 5782521 Bracket, Upper Wheel Sliding 1 3 5782531 Hinge, Upper Wheel Shaf t 1 4 5782541 Pin, Pivot 2 5 5782551 Shaft, Upper Wheel 1 6 5782561 Pin, Roll (4x16) 1 7 5782571 Knob, Blade T rack Adjustment 1 (M8x55) 8 5782581 Nut, Wing (M8x1.
23 Exploded View – Gearbox – Models 8201 and 8203.
24 R ef Part. No. Number Description Qty 1 5783831 Housing Gearbox 1 2 5629151 Bearing (6206ZZ) 1 3 9100441 Bearing (6200ZZ) 3 4 5783851 Bearing (6303ZZ) 1 5 5783861 Plug 2 6 5783871 Seal, Oil (30x7) .
25 Exploded V iew – Gearbox – Models 8201VS and 8203VS.
26 Parts Listing – Gearbox – Models 8201VS and 8203VS R ef Part. No. Number Description Qty 1 5513790 Housing Gearbox 1 2 5513791 Packing 1 3 5783861 Plug 2 4 578391 1 Gauge, Oil Level 1 5 5513794.
27 Parts List – Optional Riser Block – All Models R ef Part. No. Number Description Qt y 1 578451 1 Block, Riser 1 2 5784521 Guard, Blade 1 3 5784531 Hook, Bracket 2 4 5784541 Screw , Self T appin.
28 Parts List – Optional Rip Fence – All Models R ef Part. No. Number Description Qt y 1 578481 1 Rail, Guide 2 2 5784821 Fence, Rip 1 3 5784831 Seat Assembly , Clamp 1 4 5784841 Clamp Rail 1 5 57.
29 Notes:.
.
.
WMH T ool Group 2420 V antage Drive Elgin, IL 60123 Phone: 847-274-6848.
Ein wichtiger Punkt beim Kauf des Geräts Wilton 8203 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Wilton 8203 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Wilton 8203 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Wilton 8203 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Wilton 8203 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Wilton 8203 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Wilton 8203 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Wilton 8203. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Wilton 8203 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
