Benutzeranleitung / Produktwartung 9200 SERIES des Produzenten Whirlpool
Zur Seite of 24
Upper spray arm Bonom rack Rack bumper Heating &amen Sllverware bas Lower spray arm I I Model and Access serial number I Door color panel panel label (on right side) 9200 SERIES DISH WASHERS.
Contents Page Important Safety Instructions ....... Operating Instructions .............. Using your dishwasher for the first time . Before starting your dishwasher ....... Starting your dishwasher ....... . ...... Changing a cycle setting ...........
Important Safety Instructions l Read all instructions before using l DO NOT wash plastic items unless marked the dishwasher. “Dishwasher Safe” or the equrvalent. If not l Properly connect to electricity and water. marked, check manufacturer’s l DISHWASHER MUST BE ELECTRICALLY recommendations.
Operating Instructions Continued Control pads Starting your dishwasher 1. Press the START pad once to display the cycle and options. Skip to Step 4 if you want lo run the cycle and options shown by the lights. 2. Press the CYCLE pad until the cycle you want is indicated by a srgnal light.
Delaying a wash The DELAY pad allows you to delay the start of a cycle for 2 hours after loading the dishwasher. For example, use the DELAY to run the dishwasher during off-peak hours of electrical use. 1. Press the DELAY pad once to display the last cycle and options, selection.
Operating Instructions Continued Control panel lock-out feature This feature lets you lock-out the function of the control pads (except to cancel or pause a cycle that is running). When the control panel is locked- out, the dishwasher cannot be started and a running cycle cannot be changed.
The WATER HEATING signal light The WATER HEATING signal light comes on during the water heating portions of the Pots 8 Pans Cycle. The signal light will also come on during the water heating portion of other cycles when the Hi-Temp Option is selected.
What happens in each cycle Pots 8 Pans Cycle A double wash with maximum cleaning for cooked-on or baked-on foods. Cycle time’ is about 73 minutes plus the time needed while the timer delays to heat the water (marked t) to 140°F (60%) in both washes and the last rinse.
Normal Cycle A single wash for normal, everyday soiled loads. (The Energy Guide Label is based on this cycle.) Cycle time’ is about 66 minutes plus the time needed while the timer delays to heat the water to 140°F (60%) in the wash (marked t) and, if the Hi-Temp Option is selected, in the final rinse (marked tt).
Operating Instructions Continued Rinse 8 Hold Cycle For rinsing a few items to be washed one or more days later. Cycle time is about 12 minutes. 10 I Rinse I I Rinse I I 1 What happens in each option Options can be selected by pressing the OPTIONS pad.
Proper Loading Cup and glass load Preparation for loading It is not necessary to rinse dishes before putting them into the dishwasher. Just remove large pieces, bones and other hard items. The POWER CLEAN’” Module will remove food particles from the water.
Proper Loading Continued 1 Lower Mixed load =v Adjustable top rack The top rack does not have to be level. l Raise or lower one or both sides to help fit tall items in the top or bottom rack. l Turn knob clockwise to raise a side. l Turn knob counterclockwise to lower a side.
Silverware basket loading Load forks and spoons so lhey don’t nest together. Spray can’t reach nested items. Mix items in each section of the basket.
Adding Detergent Liquid dlshwasher detergent See phosphorus content on product labels. Cover Cover Latch What kind of detergent to use Use automatic dishwasher detergent only. Other detergents are too mild and much too sudsy to work in the dishwasher.
Using Rinse Agent Dispenser Rinse agent dispenser Keep the rinse agent dispenser filled with a liquid rinse agent such as Jet-Drys A rinse agent greatly improves the drying of dishes by helping water flow off of them during the last rinse. A rinse agent also keeps water from forming droplets and drying as spots.
For Best Results Hot water is a must Hot water dissolves and activates the dishwashing detergent. Hot water dissolves grease on dishes and helps dry glasses spot-free. Make certain loads are washed in hot water. Two ways to have a reliable hot water supply.
Energy saving tips You can help save energy if you: 1. Wash full loads. Running a half-filled dish- washer uses the same amount of electricity and hot water as a fully loaded machine. 2. Use the Low Energy Cycle whenever possible. It uses less hot water and energy than other cycles.
Common Dishwashing Problems Spotting and filming (hard water film) Hard water Fill detergent dispensers to capacity. Use dishwasher detergent with highest available phosphorus content. May be necessary to install water softener. To remove spots and film, try a vinegar rinse.
Dishes not washing clean Water is not hot enough Water temperature should be at least 140°F (SOOC). Set water heater thermostat to a higher setting. Run water at sink until hot before starting and/or use Hi-Temp Option. Improper loading Make sure dishes and glassware are loaded so spray reaches all surfaces and items drain properly.
If You Need Service Or Assistance We suggest you follow these steps: 1. Before calling for assistance,. Performance problems often result from little things you can find and fix yourself without tools of any kind.
3. If you need service’... Whirlpool has a nationwide 2 network of authorized TK+l oly WhirlpoolsM service com- SERv,cE panies. Whirlpool service technicians are trained to fulfill the product warranty and provide after-warranty service, anywhere in the United States.
Notes 22.
POWER CLEAN’” washing system parts covered by your warranty rh spray arm ‘Spray tower N0ZZle cap CLEAN and motor.
I- WHIRLPOOL” Dishwasher Warranty DW017 LENGTH OF WARRANTY WHIRLPOOL WILL PAY FOR FSPs replacemenl pans and repair labor to correcl defects in materials or workmanshio.
Ein wichtiger Punkt beim Kauf des Geräts Whirlpool 9200 SERIES (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Whirlpool 9200 SERIES noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Whirlpool 9200 SERIES - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Whirlpool 9200 SERIES reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Whirlpool 9200 SERIES erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Whirlpool 9200 SERIES besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Whirlpool 9200 SERIES verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Whirlpool 9200 SERIES. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Whirlpool 9200 SERIES gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
