Benutzeranleitung / Produktwartung 1GR35M ML-136407, 1GR45M ML-136408, 1GR65M ML-136409, 1GR85M ML-136410, 2GR45MF ML-136417, 2GR65MF des Produzenten Vulcan-Hart
Zur Seite of 20
VULCAN-HART DIVISION OF ITW FOOD EQUIPMENT GROUP, LLC WWW.VULCANHART.COM INST ALLA TION & OPERA TION MANUAL For additional information on Vulcan-Hart or to locate an authorized parts and service provider in your area, visit our website at www .vulcanhart.
— 2 — GR SERIES GAS FRYERS IMPORT ANT FOR YOUR SAFETY THIS MANUAL HAS BEEN PREP ARED FOR PERSONNEL QUALIFIED T O INST ALL GAS EQUIPMENT , WHO SHOULD PERFORM THE INITIAL FIELD ST ART -UP AND ADJUSTMENTS OF THE EQUIPMENT COVERED BY THIS MANUAL.
— 3 — GR SERIES GAS FRYERS T ABLE OF CONTENTS IMPORTANT FOR YOUR SAFETY ................................................................................................. 2 INTRODUCTION ..............................................................
— 4 — GR SERIES GAS FRYERS EXTENDING SHORTENING LIFE ........................................................................................... 14 DRAINING THE TANK .................................................................................
— 5 — GR SERIES GAS FRYERS INTRODUCTION GENERAL Vulcan Fryers are produced with quality workmanship and material. Proper installation, usage and maintenance will result in many years of satisfactory performance. Before installing the fryer, thoroughly read this manual and carefully follow all instructions in the order given.
— 6 — GR SERIES GAS FRYERS RECEIVING AND UNPACKING This fryer was carefully inspected before leaving the factory. Upon acceptance of the shipment, the transportation company assumes full responsibility for safe delivery. Immediately after unpacking the fryer, check for possible shipping damage.
— 7 — GR SERIES GAS FRYERS INST ALLA TION WARNING: THIS EQUIPMENT SHALL BE INSTALLED ONLY BY A LICENSED GAS FITTER. Caution: Do not use the door or its handle to lift the fryer.
— 8 — GR SERIES GAS FRYERS Air Supply and Ventilation WARNING: DO NOT OBSTRUCT THE FLOW OF COMBUSTION/ VENTILATION OR AIR OPENINGS AROUND THE FRYER. ADEQUATE CLEARANCE AROUND THE FRYER IS NECESSARY FOR SERVICING AND PROPER BURNER OPERATION. • Install fryer in an area with sufficient air supply for gas combustion at fryer burners.
— 9 — GR SERIES GAS FRYERS FLUE CONNECTION Caution: Ensure that your ventilation system does not cause a down draft at the fryer's flue opening. Down drafts will not allow the fryer to exhaust properly and will cause overheating which may cause permanent damage.
— 10 — GR SERIES GAS FRYERS Quick-Disconnect for Units on Casters For an appliance equipped with casters: • The installation shall be made with a connector that complies with the Standard for Connectors for Movable Gas Appliances, ANSI Z21.69 or Connectors for Moveable Gas Appliances, CAN/CGA-6.
— 11 — GR SERIES GAS FRYERS OPERA TION WARNING: HOT OIL AND PARTS CAN CAUSE BURNS. USE CARE WHEN OPERATING, CLEANING, AND SERVICING THE FRYER. WARNING: SPILLING HOT FRYING COMPOUND CAN CAUSE SEVERE BURNS. DO NOT MOVE FRYER WITH- OUT DRAINING ALL FRYING COMPOUND FROM THE TANK.
— 12 — GR SERIES GAS FRYERS CAUTION: Solid shortening should NOT be used with GRM Fryers with millivolt controls. Melting solid shortening will damage the fryer tank and void your warranty. • Close the drain valve. • Fill the fryer tank with liquid shortening.
— 13 — GR SERIES GAS FRYERS TURNING OFF THE FRYER (FREE-STANDING MODELS) 1 . Turn the thermostat OFF. 2 . To keep the pilot lit, turn the gas valve knob to “I” in PILOT. 3 . To shut off all gas to the system, including the pilot, turn the gas valve knob to OFF.
— 14 — GR SERIES GAS FRYERS BASIC FRYING INSTRUCTIONS • Set the desired temperature and allow shortening to heat up to that temperature. • Fry items that are about the same size together to ensure equal doneness. • Drain or wipe dry raw or wet foods to minimize splatter when lowering into the hot shortening.
— 15 — GR SERIES GAS FRYERS DAILY FILTERING – ALL MODELS WARNING: HOT OIL AND HOT PARTS CAN CAUSE BURNS. USE CARE WHEN OPERATING, CLEANING, AND SERVICING THE FRYER. WARNING: WHEN HANDLING HOT OIL, WEAR INSULATED AND OIL- PROOF GLOVES. • Filter shortening at least once a day.
— 16 — GR SERIES GAS FRYERS BOIL OUT PROCEDURE Weekly or as required 1 . Drain the tank as described under DRAINING THE TANK. 2 . Once the shortening has been drained, flush out scraps and sediment with a small amount of warm shortening, using tank brush.
— 17 — GR SERIES GAS FRYERS MAINTENANCE WARNING: HOT OIL AND HOT PARTS CAN CAUSE BURNS. USE CARE WHEN OPERATING, CLEANING, AND SERVICING THE FRYER. WARNING: SPILLING HOT FRYING COMPOUND CAN CAUSE SEVERE BURNS. DO NOT MOVE FRYER WITHOUT DRAINING ALL FRYING COMPOUND FROM THE TANK.
— 18 — GR SERIES GAS FRYERS TROUBLESHOOTING WARNING: FRYERS WITH KLEENSCREEN™ FILTERS: CERTAIN PROCEDURES IN THIS SECTION REQUIRE ELECTRICAL TESTS OR MEASUREMENTS WHILE POWER IS APPLIED TO THE MACHINE.
— 19 — GR SERIES GAS FRYERS.
F-31233 Rev. B (May 2006) PRINTED IN U.S.A ..
Ein wichtiger Punkt beim Kauf des Geräts Vulcan-Hart 1GR35M ML-136407, 1GR45M ML-136408, 1GR65M ML-136409, 1GR85M ML-136410, 2GR45MF ML-136417, 2GR65MF ML-136418, 2GR85MF ML-136419, (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Vulcan-Hart 1GR35M ML-136407, 1GR45M ML-136408, 1GR65M ML-136409, 1GR85M ML-136410, 2GR45MF ML-136417, 2GR65MF ML-136418, 2GR85MF ML-136419, noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Vulcan-Hart 1GR35M ML-136407, 1GR45M ML-136408, 1GR65M ML-136409, 1GR85M ML-136410, 2GR45MF ML-136417, 2GR65MF ML-136418, 2GR85MF ML-136419, - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Vulcan-Hart 1GR35M ML-136407, 1GR45M ML-136408, 1GR65M ML-136409, 1GR85M ML-136410, 2GR45MF ML-136417, 2GR65MF ML-136418, 2GR85MF ML-136419, reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Vulcan-Hart 1GR35M ML-136407, 1GR45M ML-136408, 1GR65M ML-136409, 1GR85M ML-136410, 2GR45MF ML-136417, 2GR65MF ML-136418, 2GR85MF ML-136419, erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Vulcan-Hart 1GR35M ML-136407, 1GR45M ML-136408, 1GR65M ML-136409, 1GR85M ML-136410, 2GR45MF ML-136417, 2GR65MF ML-136418, 2GR85MF ML-136419, besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Vulcan-Hart 1GR35M ML-136407, 1GR45M ML-136408, 1GR65M ML-136409, 1GR85M ML-136410, 2GR45MF ML-136417, 2GR65MF ML-136418, 2GR85MF ML-136419, verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Vulcan-Hart 1GR35M ML-136407, 1GR45M ML-136408, 1GR65M ML-136409, 1GR85M ML-136410, 2GR45MF ML-136417, 2GR65MF ML-136418, 2GR85MF ML-136419,. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Vulcan-Hart 1GR35M ML-136407, 1GR45M ML-136408, 1GR65M ML-136409, 1GR85M ML-136410, 2GR45MF ML-136417, 2GR65MF ML-136418, 2GR85MF ML-136419, gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.