Benutzeranleitung / Produktwartung D5500 des Produzenten Vivitek
Zur Seite of 113
— i — Copyright This publication, including all photographs, illustratio ns and software, is protected under international copy- right laws, with all rights reserved. Neither this man ual, nor any of the material contained herein, may be reproduced without written consent of the author.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l — ii — Important Safety Informatio.
P P P r r r e e e f f f a a a c c c e e e – iii – Power Safety Only use the supplied power cord. Do not place anything on the power cord. Place the power cord where it will not be in the way of foot traffic. Remove the batteries from the remote control when storing or not in use for a prolonged period.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l — iv — Main Features • Lightweight unit, easy to pack away and transport. • Compatible with all major video st andards including NTSC, P AL, and SECAM.
P P P r r r e e e f f f a a a c c c e e e – v – Table of Contents INTRODUCTI ON................................................................................................................... .............................................. 1 P ACKING C HECKLIST .
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l — vi — U SING THE P HYSICAL L OCK ...................................................
P P P r r r e e e f f f a a a c c c e e e – vii – Status Read Co mm and Table ...................................................................................................... .................................. 99 S CREEN T RIGGER ...........
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 1 – I NTRODUCTION Packing Checkl.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 2 – Views of Projector Parts Front-right View I TEM L ABEL D ESCRIPTION S EE PAGE : 1.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 3 – Top view I TEM L ABEL D ESCRIPTION S EE PAGE : 1. Lens control panel See Lens Controls 5 2.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 4 – Bottom view I TEM L ABEL D ESCRIPTION S EE PAGE : 1. Height adjusters Adjust projection height 32 2.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 5 – Top Features Lens Controls I TEM L ABEL D ESCRIPTION S EE PAGE : 1. ZOOM Increase/decrease projected image size 38 2.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 6 – OSD Controls and Status LEDs I TEM L ABEL D ESCRIPTION S EE PAGE : 1. MENU Open / Close the OSD 47 2.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 7 – I TEM L ABEL D ESCRIPTION S EE PAGE : Green Orange 10. POWER (LED) Flashing See Indicator Messages 87 11.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 8 – Terminal Panel Features I TEM L ABEL D ESCRIPTION S EE PAGE : 1. COMPUTER 3 IN Connect the DVI-D cable (not supplied) from a computer 21 2.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 9 – I TEM L ABEL D ESCRIPTION S EE PAGE : 10. POWER SWITCH Turn on/off the projector 35 11.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 10 – Remote Control Parts Important: 1. Avoid using the projector with bright fluorescent lighting tur ned on.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 11 – I TEM L ABEL D ESCRIPTION S EE PAGE : 7. Up cursor Navigates and changes settings in the OSD 47 8.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 12 – Remote Control Operating Range The remote control uses infrared transmission to control the projector.
– 13 – S ETUP AND O PERATION Inserting the Remote Control Batteries 1. Remove the battery compartment cover by sliding the cover in the di- rection of the arrow. 2. Insert the supplied batteries taking note of the polarity (+/-) as shown here. 3. Replace the cover.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 14 – Installing or Removing the .
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 15 – 3.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 16 – Throw Distance and Screen Size Example of GB940G: The further your projector is from the screen or wa ll, the larger the image.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 17 – Screen Size GB949G GB957G 2.22 - 4.43 4.43 - 8.3 Diagonal Width Height Distance [inches] [m] [inches] [m] [inches] [m] [inches] [m] [inches] [m] 40 1.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 18 – Installing the Optional Color Wheel The projector comes with a four-segment color wheel installed.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 19 – 4.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 20 – 6.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 21 – Making Connections Connecti.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 22 – Note: Failure to follow the above steps may not activate t he digital output of the graphics card resulting in no picture being displayed.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 23 – Connecting Your DVD Player with Component Output To connect a DVD Player to the proj ector, refer to the following guide.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 24 – Connecting Your VCR or Laser Disc Player To connect your VCR or Laser Disc Pl ayer, refer to the following diagram.
– 25 – P ROJECTING AN I MAGE (B ASIC O PERATION ) Turning on the Projector Once the projector is correctly located and the power cable and other connections are in place, it is important that the projector is powered on correctly in order to avoid damage to components and un- necessary wear and tear.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 26 – Note on Startup Screen (Menu Language Select screen) In the first instance of powering on the projector, the language menu is displayed to select the default language.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 27 – Selecting an Input Source The Input Source can be selected fr om the projector's control panel or from the remote control unit.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 28 – Adjusting the Picture Position and Picture Size The Picture Position and Picture Size can be adjusted manually from the lens control panel or from the remote control unit.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 29 – 4. The Screen window is displayed. Select the desired picture size us- ing ▲ or ▼ and press .
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 30 – From the Remote Control Unit 1. Press Menu and select the Set- ting menu using ▲ or ▼ .
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 31 – 4. To alter the picture size, press Menu and select the Adjust menu using ▲ or ▼ .
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 32 – Adjusting the Projector Level 1. To raise the level of the projector, twist the adjusters clockwise.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 33 – Optimizing an RGB Image Automatically Adjusting the Image Using AUTO To optimize an RGB image automatica lly refer to the following guide.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 34 – Adjusting Volume Up and Down The volume can be adjusted from t he OSD Control Panel or with the Remote Control unit.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 35 – Turning off the Projector Once the projector is no longer requi red, it is important to shut it down correctly to avoid damage or unnecessary wear and tear to the projector.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 36 – About Direct Power Off The projector has a feature called "Direct Power Off".
– 37 – C ONVENIENT F EATURES Turning Off the Image and Sound The projected image and sound can be tu rned off for short periods of time with the remote control. This feature is useful for breaki ng up presentations or for other brie f interruptions in projections.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 38 – Adjusting the Focus/Zoom Manually The focus and zoom can be adjusted manually from t he projector focus/zoom panel.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 39 – Changing Lamp Mode The projector has two lamp modes available, Normal and Eco .
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 40 – Getting Information The Information screen provides deta ils on the life of consumable items within the projector as well as other information such as software version.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 41 – Adjusting Position/Total Do.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 42 – Correcting Keystone by Using the Remote Control Important: When adjusting the keystone, place the projector in the following position.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 43 – A DJUSTMENT H ORIZONTAL V ERTICAL Keystone Max. +/– 35° approx. Max. +/– 40° approx.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 44 – Preventing the Unauthorized Use of the Projector The projector has a built-in security feature to lock the OSD control panels and deny remote control operation.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 45 – 4. The PIN code window is displayed. Enter a PIN code between 4 and 10 characters using ▲▼◄► .
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 46 – Using the Physical Lock Using the Kensington Lock If you are concerned about security, attach the projector to a permanent object with the Kensington slot and a security cable.
– 47 – U SING O N -S CREEN D ISPLAY Using the Menus The projector has an On-Screen Display (OSD) that lets you make image adjustments and change various settings. Navigating the OSD You can use the remote control or the buttons on the top of t he projector to navigate and make changes to the OSD.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 48 – 2. Press the cursor ◄ or ► button to move through secondary menus. 3. Press ▲ or ▼ to select menu items and ◄ or ► to change values for settings.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 49 – Menu Tree Use the following illustrations to quickly find a setting or determine the range for a setting.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 50 –.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 51 – Menu Elements Some menus and windows contain large amounts of info rmation in a small area.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 52 – Input Menu Descriptions and Functions The Input menu displays all supported image sources.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 53 – Adjust Menu Descriptions and Functions The Adjust menu contains overall projector settings for image output such as sharpness, overscan and color matrix.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 54 – Image options menu The Image Options tab is used to configur e image options such as scr een positioning and aspect ra- tio.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 55 – Screen The Screen option allows for the adj ustment of the aspect ratio to al ter the appearance or ratio of the projected image.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 56 – Video menu The Video tab is used to configure image opt ions such as film. Access the Video tab in the Adjust menu.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 57 – Noise reduction Select the level of noise reduction required. Range: Off, Low, Mid, High.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 58 – Color matrix Color Matrices define the amount of the three-color components R (red), G (green), and B (blue) in a single point in color space.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 59 – Detail Setting Menu Descrip.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 60 – Gamma Gamma enables adjustment to the li ght intensity (brightness) of an image in order to match the source more closely.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 61 – White balance White Balance allows the projector to compensate for diffe rent colors of light being emitted by differ- ent light sources.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 62 – Color correction The Color .
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 63 – Setting Menu Descriptions a.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 64 – Keystone The keystone trapezoid c an be adjusted by selecting this option.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 65 – Lamp interval The period of time for regulating la mp usage when not in dual lamp mode.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 66 – Installation The Installation tab contains menu options for various setup conditions such as orientation and re- mote sensor mode and is accessed through the Setting menu.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 67 – L ABEL D ESCRIPTION DynamicBlack DynamicBlack TM improves the black level of the projector.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 68 – Display time Sets the amount of time a menu is displayed. Select from the following: Manual – Menus stay on screen until the Menu button is pressed again.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 69 – Key lock Turn On/Off the Key Lock function for cabinet buttons. Note: This Control Panel Lock does not a ffect the remote control functions.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 70 – Standby mode There are two standby modes available: Normal and Power-saving.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 71 – Network setting The Netw ork setting menu is accessed by using the Setup / Installation menu and contains the general LAN settings.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 72 – Option The Option tab contains miscellaneous setup menu se ttings such as Power management and De- fault input select and can be accessed by using the Setting menu.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 73 – Power management Power management enables the projecto r to automatically turn off if there is no signal received by any input.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 74 – Default input select The Default input is the image sour ce that the projector will search for automatically on startup.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 75 – Filter warning Set Filter warning to have the projector displa y a message when the air f ilter needs servicing.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 76 – Information Menu Descriptions and Functions The Information menu provides only screens for the quick access of menus.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 77 – Input The Input tab displays various source and frequency values at a glance. The following table lists all items with a description.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 78 – Network The Netw ork tab displays LAN settings as previously defined (see Network setting on page 71 ).
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 79 – Version The Version tab displays all the versi on and product details of the pr ojector and associated software (for display only).
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 80 – Reset Menu Descriptions and.
– 81 – M AINTENANCE Cleaning the projector Cleaning the Cabinet Refer to the following guide to clean the projector cabinet. 1. Wipe off dust with a clean dampened cloth. 2. Moisten the cloth with warm water and mild detergent and wipe the cabinet.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 82 – Cleaning the Filters The projector uses three filter s to keep the fans free of dus t and other particles, and should be cleaned every 500 hours of operation.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 83 – Replacing the Lamps When a lamp reaches the end of it’s usable life, the following message is displayed.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 84 – The projection lamp should be repl aced when it burns out. It should onl y be replaced with a certified replacement part, which you can order from your local dealer.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 85 – 3. Pull firmly on the module handle in the direction shown to remove the lamp.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 86 – Resetting the Lamp Time Counter After replacing the lamp(s), the lamp hour counter(s) should be reset to zero.
– 87 – A PPENDIX Troubleshooting Indicator Messages Several indicator messages are used by the projector to alert users of problems with setup or internal parts.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 88 – The LAMP LEDs P ROJECTOR S TATUS LED C ONDITION LED S EQUENCE P ROJECTOR C ONDITION Lamp off Off Off Lamp off End of the lamp life Red blink 0.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 89 – Image Problems Problem: No image appears on the screen 1. Verify the settings on your notebook or desktop PC.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 90 – Remote Control Problems Problem: The projector does not respond to the remote control 1.
– 91 – S PECIFICATIONS Projector Specifications This section provides technical information about the projector's performance. Optical Specifications I TEM D ESCRIPTION Projection system Sing.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 92 – Electrical Specifications I.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 93 – Mechanical Specifications I TEM D ESCRIPTION Dimensions 19.9" (W) x 7.6" (H) x 15.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 94 – Cabinet Dimensions.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 95 – Pin Assignments of Mini D- Sub 15 Pin Input Connector Signal Levels Video signal: 0.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 96 – Compatible Input Signal List The following table shows compatible signal ty pes, their resolution and frequency refresh rates.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 97 – PC Control Codes and Cable Connections This projector provides a functi on to control and monitor the projec tor's operations by using the RS- 232C serial port.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 98 – Functional Execution Comman.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 99 – Status Read Command Table C OMMAND F UNCTION CR0 Status Read CR6 T emperature Read PC Control Connector (DIN-9P) Note: 1.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 100 – Screen Trigger When the projector is powered ON the screen trigger output sends a low voltage trigger to the screen controller and the screen will go down.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 101 – Operation Using HTTP Browser Overview The use of HTTP server functions will allow control of the projecto r from a web browser without the installation of special software.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 102 – Configuring Network Settings The Network Settings screen is displayed as follows: http:// <the projector's IP address> /lanconf.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 103 – TEST MAIL Send a test mail to check if your settings are co rrect. Click to “Execute” to enable this feature.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r — — — U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 104 – Structure of the HTTP Server Once the projector is connected to a network and configured corre ctly, the following screen is dis- played through the web browser.
D D D L L L P P P P P P r r r o o o j j j e e e c c c t t t o o o r r r – – – U U U s s s e e e r r r ’ ’ ’ s s s M M M a a a n n n u u u a a a l l l – 105 – F UNCTION S ETTING D ESCRI.
– 106 – R EGULATORY C OMPLIANCE FCC Warning This equipment has been tested and found to comply wi th the limits for a Class B digital device pur- suant to Part 15 of the FCC Rules. These lim its are designed to prov ide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Ein wichtiger Punkt beim Kauf des Geräts Vivitek D5500 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Vivitek D5500 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Vivitek D5500 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Vivitek D5500 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Vivitek D5500 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Vivitek D5500 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Vivitek D5500 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Vivitek D5500. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Vivitek D5500 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
