Benutzeranleitung / Produktwartung VX-2200 des Produzenten Vertex Standard
Zur Seite of 66
© 2008 VERTEX STANDARD CO., LTD. EC061U90C UHF FM Transceiver VX-2100 Series VX-2200 Series Service Manual Specifications ........................................................... A-1 DSUB 15-pin Accessory Connector ...................... B-1 Exploded View & Miscellaneous Parts .
Specifications (VTX/EXP Version) General Frequency Ranges : 400 - 470 MHz (T ype A) 450 - 512 MHz (VTX, T ype D) 450 - 520 MHz (EXP , T ype D) Number of Groups : 1 groups (VX-2100 Series) 8 groups (VX-2200 Series) Number of Channels : 8 channels (VX-2100 Series) 128 channels (VX-2200 Series) Power Supply V oltage : 13.
Specifications (EU Version) A-2 General Frequency Ranges : 400 - 470 MHz Number of Groups : 1 groups (VX-2100 Series) 8 groups (VX-2200 Series) Number of Channels : 8 channels (VX-2100 Series) 128 channels (VX-2200 Series) Power Supply V oltage : 10.8 - 15.
B-1 DSUB 15-pin Accessory Connector Pin 1: AF IN ( A NALOG I NPUT ) External Microphone Input. Nominal input level is 6 mV at 600-ohm. When connect the External Microphone to this port, insert a 0.1 µF coupling capacitor between the micro- phone and this port; as shown illustlation.
C-1 Exploded View & Miscellaneous Parts No. VXSTD P/N DESCRIPTION QTY . U10206007 TRUSS HEAD SCREW M2.6X6B 10 U24308002 T APTITE SCREW M3X8NI 13 U03308002 SEMS SCREW ASM3X8NI 2 U24306002 T APTITE SCREW M3X6NI 2 VX-2100 FRONT P ANEL VX-2200 FRONT P ANEL Non-designated parts are available only as part of a designated assembly .
C-2 Exploded View & Miscellaneous Parts Note:.
D-1 Block Diagram.
D-2 Block Diagram Note:.
1. Circuit Configuration by Frequency The receiver is a double-conversion superheterodyne with a first intermediate frequency (IF) of 67.65 MHz and a second IF of 450kHz. The incoming signal from the an- tenna is mixed with the local signal from the VCO/PLL to produce the first IF of 67.
3. T ransmitter System 3-1. Mic Amplifier There are two micrphone inputs, J1004 (front) and J1006 (D-Sub). Each microphone inputs has it's own amplifier . Which micrphone is selected is controlled by the CPU and in addition, the amplified AF signal is selected with Flat- AF selection switch Q1043 ( NJM12902V ).
Introduction The VX-2100/-2200 series has been aligned at the factory for the specified performance across the entire frequency range specified. Realignment should therefore not be nec- essary except in the event of a component failure.
Alignment T est Setup Setup the test equipment as shown for transceiver align- ment, apply 13.6V DC power to the transceiver. Refer to the drawings above for Alignment Points. The Alignment T ool Outline Installation the tool Install the CE82 (Clone Editor) to your PC.
Alignment F-3 1. RX VCO T une V oltage (RX VCO) This parameter is to align the “Tune Voltage” of RX VCO. This alignment will be done automatically between the radio and PC. 1. Press the “Start” button on the "Basic Alignment" win- dow to open the RX VCO Adjustment window .
4. RX Sensitivity (RX T une) This parameter is to align the RX BPF (Band Pass Filter) for Rx sensitivity. It must be done both alignments of the “RX VCO Tune Voltage” and “PLL Reference Frequency” before this alignment is going to start. 1. Press the “Start” button to start the alignment.
RSSI SQL Full Scale <Wide> (S Full Scale W) The Alignment for the RSSI Full Scale level at Wide (5k/ 4k). Noise SQL Tight <Narrow> (TI NSQ N) The Alignment for the Noise SQL Tight level at Narrow (2.5k). N oise SQL Threshold < Narrow > (TH NSQ N) The Alignment for the Noise SQL Threshold level at Nar- row (2.
9. Sequential T one Deviation This parameter is to align the “Sequential Tone Deviation” (for 2-Tone, 5-Tone and DTMF sequential tones). 1. Press the “Start” button to start the alignment. 2. Set the v alue to get desired deviation by changing the slide bar on your PC.
CH (Channel-by-Channel) Fine Alignment Mode The CH Fine Alignment Mode allows you to align the ra- dio separately for every operating channel. The value of each parameter can be changed to the desired position us- ing the “ ” / “ ” and up/down arrow keys, direct number input, and by dragging the PC mouse.
Installation of Option G-1 The FVP-25 is an Encryption/DTMF Pageing Unit which permits secure voice communications with station within your network, while preventing others from listening us- ing normal communications equipment. It allows paging, and enables selective calling using DTMF tone sequences.
H-1 Circuit Diagram MAIN Unit (Lot 1~4) 5.0V RX:0V TX:5.0V RX:5.1V TX:0V RX:0V TX:5.0V 5.0V 12.9V 5.2V 5.1V 13.6V SHIFT ON:0.1V SHIFT OFF:3.4V 5.0V POW OFF:0V POW ON:5.6V 5.6V 7.7V 1.1V 2.2V 2.1V 5.2V 1.1V 8.1V 3.5V MUTE:0V UNMUTE:5.0V 5.1V 5.0V 5.0V 5.
H-2 Note MAIN Unit (Lot 1~4).
H-3 Parts Layout (Side A) B A D CE FH GI J 1 2 3 4 5 6 K HSM88AS (C1) (D1007, 1008) MC2850 (A7) (D1042, 1060, 1061) 2SB1201S-TL (Q1039) 3SK293 (UF) (Q1025) BH2220FVM (Q1034) BR93L66RFVM (Q1061) LC87F5.
H-4 Parts Layout (Side B) b a d ce fh g i j 1 2 3 4 5 6 k DAN222 (N) (D1020, 1035, 1039) MC2850 (A7) (D1021, 1027, 1041 1046, 1047, 1048 1053, 1054) 2SK508 (K52) (Q1029, 1031) 2SK880GR (XG) (Q1037) 2S.
H-5 MAIN Unit (Lot 5~9) Circuit Diagram.
H-6 MAIN Unit (Lot 5~9) MAIN Unit.
H-7 MAIN Unit (Lot 5~9) B A D CE FH GI J 1 2 3 4 5 6 K Parts Layout (Side A) BH2220FVM (Q1034) BR93L66RFVM (Q1061) MTM231230L (BL) (Q 1008, 1011, 1012) 2SK397300L (Q1050, 1055, 1060, 1063, 1070) NJM78.
H-8 MAIN Unit (Lot 5~9) b a d ce fh g i j 1 2 3 4 5 6 k Parts Layout (Side B) DAN222 (N) (D1020, 1035, 1039) MC2850 (A7) (D1021, 1027, 1041 1046, 1047, 1048 1053, 1054) 2SK508 (K52) (Q1029, 1031) 2SK8.
H-9 MAIN Unit (Lot 10~12) Circuit Diagram.
H-10 MAIN Unit (Lot 10~12) Note.
H-11 MAIN Unit (Lot 10~12) B A D CE FH GI J 1 2 3 4 5 6 K HSM88AS (C1) (D1007, 1008) MC2850 (A7) (D1042, 1060, 1061) 2SB1201S-TL (Q1039) 3SK293 (UF) (Q1025) BH2220FVM (Q1034) BR93L66RFVM (Q1061) LC87F.
H-12 MAIN Unit (Lot 10~12) b a d ce fh g i j 1 2 3 4 5 6 k DAN222 (N) (D1020, 1035, 1039) MC2850 (A7) (D1021, 1027, 1041 1046, 1047, 1048 1053, 1054) 2SK508 (K52) (Q1029, 1031) 2SK880GR (XG) (Q1037) 2.
H-13 MAIN Unit (Lot 13~) Circuit Diagram.
H-14 MAIN Unit (Lot 13~) Note.
H-15 MAIN Unit (Lot 13~) B A D CE FH GI J 1 2 3 4 5 6 K Parts Layout (Side A) BH2220FVM (Q1034) BR93L66RFVM (Q1061) MTM231230L (BL) (Q 1008, 1011, 1012) 2SK397300L (Q1050, 1055, 1060, 1063, 1070) NJM7808DL1A (Q1006) S-AU83AL (25 W, Ver A) S-AU83AH (25 W, Ver D) RA55H4047M (45 W, Ver A) (Lot.
H-16 MAIN Unit (Lot 13~) b a d ce fh g i j 1 2 3 4 5 6 k Parts Layout (Side B) DAN222 (N) (D1020, 1035, 1039) MC2850 (A7) (Lot. 1~19) DAN217U (A7) (Lot.
H-17 MAIN Unit PCB with Components CS1888002 EXP TYPE D 45 W CS1888003 VTX TYPE D 45 W CS1888005 CE TYPE A 25 W CS1888006 VTX TYPE D 25 W CS1888007 EXP TYPE D 25 W CS1888008 VTX TYPE A 25 W CS1888009 .
H-18 MAIN Unit C 1026 CHIP CAP. 33pF 50V CH GRM1552C1H330JZ01D K22178224 1- A C4 C 1027 CHIP CAP. 100pF 50V CH GRM1552C1H101JD01D K22178236 1- B a3 C 1028 CHIP CAP. 0.01uF 16V B GRM36B103K16PT K22128804 1- B a3 C 1028 CHIP CAP. 0.01uF 25V B GRM155B11E103KA01D K22148834 19- B a3 C 1029 CHIP CAP.
H-19 MAIN Unit C 1080 CHIP CAP. 100pF 50V CH GRM1552C1H101JD01D K22178236 1- A C5 C 1081 CHIP CAP. 100pF 50V CH GRM1552C1H101JD01D K22178236 1- A A5 C 1083 CHIP CAP. 220pF 25V CH GRM36CH221J25PT K22148203 1- B b3 C 1083 CHIP CAP. 220pF 50V CH GRM1552C1H221JA01D K22179713 19- B b3 C 1084 CHIP CAP.
H-20 MAIN Unit C 1138 CHIP CAP. 100pF 50V CH GRM1552C1H101JD01D K22178236 1- B e2 C 1139 CHIP CAP. 0.001uF 50V B GRM155B11H102KA01D K22178809 1-9 B e2 C 1139 CHIP CAP. 47pF 50V CH GRM1552C1H470JZ01D K22178228 VERSION A 10- B e2 C 1139 CHIP CAP. 0.001uF 50V B GRM155B11H102KA01D K22178809 VERSION D 10- B e2 C 1140 CHIP CAP.
H-21 MAIN Unit C 1195 CHIP CAP. 3pF 50V CJ GRP1553C1H3R0CZ01E K22178205 VERSION D 10- B e4 C 1196 CHIP CAP. 0.0047uF 25V B GRM36B472K25PT K22148830 1- A D 5 C 1196 CHIP CAP. 0.0047uF 50V B GRM155B11H472KA01D K22178838 19- A D5 C 1197 CHIP CAP. 0.001uF 50V B GRM155B11H102KA01D K22178809 1- B e4 C 1198 CHIP CAP.
H-22 MAIN Unit C 1259 CHIP CAP. 180pF 25V CH GRM36CH181J25PT K22148201 1- A I5 C 1259 CHIP CAP. 180pF 50V CH GRM1552C1H181JA01D K22179711 19- A I5 C 1260 CHIP CAP. 0.001uF 50V B GRM155B11H102KA01D K22178809 1- A D3 C 1261 CHIP CAP. 0.0033uF 50V B GRM155B11H332KA01D K22178815 1- A J5 C 1262 CHIP TA.
H-23 MAIN Unit C 1317 CHIP CAP. 0.01uF 25V B GRM155B11E103KA01D K22148834 19- B j2 C 1319 CHIP TA.CAP. 4.7uF 16V TEESVA1C475M8R K78120031 1- B c5 C 1321 CHIP CAP. 0.001uF 50V B GRM155B11H102KA01D K22178809 1- B b5 C 1323 CHIP CAP. 100pF 50V CH GRM1552C1H101JD01D K22178236 1- B i2 C 1324 CHIP CAP.
H-24 MAIN Unit C 1390 CHIP CAP. 2pF 50V CK GRM1554C1H2R0CZ01D K22178204 VERSION A 10- B f2 C 1391 CHIP CAP. 9pF 50V CH GRM1552C1H9R0DZ01D K22178211 VERSION A 10- B f2 C 1391 CHIP CAP. 5pF 50V CH GRM1552C1H5R0CZ01D K22178207 VERSION D 10- B f2 C 1393 CHIP CAP.
H-25 MAIN Unit D 1053 DIODE MC2850-T111-1 G2070704 1- B i1 D 1053 DIODE DAN217U T106 G2071236 20- B i1 D 1054 DIODE MC2850-T111-1 G2070704 1- B j1 D 1054 DIODE DAN217U T106 G2071236 20- B j1 D 1055 DI.
H-26 MAIN Unit L 1023 M.RFC 0.082uH HK1608 82NJ-T L1690527 1- B e3 L 1024 M.RFC 1uH LK1608 1R0K-T L1690687 1- B e3 L 1025 M.RFC 0.39uH 2% C1608CB-R39G-RF L1691107 1- B f3 L 1026 M.RFC 0.22uH HK1608 R22J-T L1690940 1- B f3 L 1027 COIL 0.02uH ASF050525-20R0NJ L0022850 1-9 B f3 L 1027 COIL 0.
H-27 MAIN Unit Q 1023 TRANSISTOR 2SC5226-4-TL G3352268D 1- B e2 Q 1024 TRANSISTOR 2SC5226-4-TL G3352268D 1- B e2 Q 1025 FET 3SK293(TE85L,F) G4802938 1- A H 3 Q 1026 TRANSISTOR RT1N441U-T11-1 G3070247 .
H-28 MAIN Unit R 1009 CHIP RES. 270k 1/16W 5% RMC1/16S 274JTH J24189054 1- A C4 R 1010 CHIP RES. 100k 1/16W 5% RMC1/16S 104JTH J24189049 1- B a3 R 1011 CHIP RES. 470 1/16W 5% RMC1/16S 471JTH J24189021 1- A I2 R 1012 CHIP RES. 100 1/4W 5% RMC1/4 101JATP J24245101 1- A H2 R 1013 CHIP RES.
H-29 MAIN Unit R 1071 CHIP RES. 47k 1/16W 5% RMC1/16S 473JTH J24189045 1- A B5 R 1072 CHIP RES. 47k 1/16W 5% RMC1/16S 473JTH J24189045 1- A F3 R 1073 CHIP RES. 10k 1/16W 5% RMC1/16S 103JTH J24189037 1- A G5 R 1074 CHIP RES. 100k 1/16W 5% RMC1/16S 104JTH J24189049 1- A F3 R 1075 CHIP RES.
H-30 MAIN Unit R 1136 CHIP RES. 100k 1/16W 5% RMC1/16S 104JTH J24189049 1- A H3 R 1137 CHIP RES. 100 1/16W 5% RMC1/16S 101JTH J24189013 1- A E3 R 1138 CHIP RES. 1k 1/16W 5% RMC1/16S 102JTH J24189025 1- B d3 R 1139 CHIP RES. 100 1/16W 5% RMC1/16S 101JTH J24189013 1- A H3 R 1140 CHIP RES.
H-31 MAIN Unit R 1194 CHIP RES. 82k 1/16W 5% RMC1/16S 823JTH J24189048 1- A I5 R 1195 CHIP RES. 22 1/16W 5% RMC1/16S 220JTH J24189005 1- B e4 R 1196 CHIP RES. 47k 1/16W 5% RMC1/16S 473JTH J24189045 1- A D4 R 1198 CHIP RES. 82k 1/16W 5% RMC1/16S 823JTH J24189048 1- A H5 R 1199 CHIP RES.
H-32 MAIN Unit R 1277 CHIP RES. 22 1/16W 5% RMC1/16S 220JTH J24189005 1- B d4 R 1279 CHIP RES. 1k 1/16W 5% RMC1/16S 102JTH J24189025 1- A B4 R 1280 CHIP RES. 0 1/16W 5% RMC1/16 000JATP J24185000 1- A A1 R 1281 CHIP RES. 47k 1/16W 5% RMC1/16S 473JTH J24189045 1- A B4 R 1282 CHIP RES.
H-33 MAIN Unit R 1353 CHIP RES. 47k 1/10W 5% RMC1/10T 473J J24205473 45W 10- A G2 R 1357 CHIP RES. 100k 1/16W 5% RMC1/16S 104JTH J24189049 25W 10- A H3 R 1358 CHIP RES. 1k 1/16W 5% RMC1/16S 102JTH J24189025 10- A B1 R 1359 CHIP RES. 1k 1/16W 5% RMC1/16S 102JTH J24189025 10- B j1 R 1360 CHIP RES.
H-34 MAIN Unit Note.
I-1 FRONT-A Unit (VX-2100) Circuit Diagram RX: 0V TX: 4.9V RX: 4.9V TX: 0V 5.0V 13.6V.
I-2 FRONT-A Unit (VX-2100) Parts Layout (Side A) 1 2 3 B A D CE F b a d ce f 1 2 3 Parts Layout (Side B) RT1N441U (N3) (Q2001, 2002, 2003, 2004, 2006, 2008, 2009, 2010) BRPG1211C (D2001) CD4094BPWR (Q.
I-3 FRONT-A Unit (VX-2100) PCB with Components CB3474001 Printed Circuit Board FR014510B 1- C 2001 CHIP TA.CAP. 4.7uF 25V TEESVB21E475M8R K78140019 1- B f2 C 2002 CHIP CAP. 0.1uF 25V B GRM21BB11E104KA01L K22140811 1- B e2 C 2003 CHIP CAP. 0.1uF 16V B GRM188B11C104KA01D K22124805 1- B e2 C 2004 CHIP TA.
I-4 Note FRONT-A Unit (VX-2100).
J-1 FRONT-B Unit (VX-2200) Circuit Diagram 5.0V 5.0V DIMMER LEVEL 3: 4.8V RX: 0V TX: 4.9V RX: 4.9V TX: 0V.
J-2 FRONT-B Unit (VX-2200) Parts Layout (Side A) 1 2 3 B A D CE F b a d ce f 1 2 3 Parts Layout (Side B) XP1501 (R5) (Q3002, 3007) 2SA1602A (MF) (Q3008) LCD (DS3001) BRPG1211C (D3005) 2SB1132 (BA) (Q3.
J-3 FRONT-B Unit (VX-2200) PCB with Components CB3475001 Printed Circuit Board FR014520C 1- C 3001 CHIP TA.CAP. 4.7uF 25V TEESVB21E475M8R K78140019 1- B e1 C 3002 CHIP CAP. 0.1uF 25V B GRM21BB11E104KA01L K22140811 1- B d1 C 3003 CHIP CAP. 0.1uF 16V B GRM188B11C104KA01D K22124805 1- B d1 C 3004 CHIP CAP.
J-4 Note: FRONT-B Unit (VX-2200).
K-1 FVP-25 Encryption/DTMF Pager Unit (Option) M64026FP (Q1001) Circuit Diagram Parts Layout LC73881 (Q1002) DTC144EU (26) (Q1003) Side B Side A.
K-2 FVP-25 Encryption/DTMF Pager Unit (Option) Printed Circuit Board FR005010F C 1001 CHIP CAP. 0.1uF 16V B GRM188B11C104KA01D K22124805 1- C 1002 CHIP CAP. 0.01uF 25V B GRM39B103M25PT K22144802 1- C 1003 CHIP CAP. 10pF 50V CH GRM1882C1H100JA01D K22174211 1- C 1004 CHIP CAP.
L-1 FVP-36 Voice Inversion Type Encryption Unit (Option) M64026FP (Q1001) Circuit Diagram Parts Layout Side B Side A.
L-2 FVP-36 Voice Inversion Type Encryption Unit (Option) Printed Circuit Board FR005010F C 1003 CHIP CAP. 10pF 50V CH GRM1882C1H100JA01D K22174211 1- C 1004 CHIP CAP. 10pF 50V CH GRM1882C1H100JA01D K22174211 1- C 1005 CHIP CAP. 0.1uF 16V B GRM188B11C104KA01D K22124805 1- C 1007 CHIP CAP.
.
Copyright 2008 VERTEX STANDARD CO., LTD. All rights reserved No portion of this manual may be reproduced without the permission of VERTEX STANDARD CO., LTD.
Ein wichtiger Punkt beim Kauf des Geräts Vertex Standard VX-2200 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Vertex Standard VX-2200 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Vertex Standard VX-2200 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Vertex Standard VX-2200 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Vertex Standard VX-2200 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Vertex Standard VX-2200 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Vertex Standard VX-2200 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Vertex Standard VX-2200. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Vertex Standard VX-2200 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
