Benutzeranleitung / Produktwartung Antara (2012) des Produzenten Vauxhall
Zur Seite of 209
0 - 1 Owner’s Manual Model Year 2012 Edition : February 2012 TS 1700-A-12 VAUXHALL Antara Owner’s Manual Model Year 2012 Edition: February 2012 TS 1700-A-12.
Introduction .................................... 2 In brief ............................................ 6 Keys, doors and windows ............ 18 Seats, restraints ........................... 33 Storage ........................................ 52 Instruments and controls .
2 Introduction Introduction.
Introduction 3 Vehicle specific data Please enter your vehicle's data on the previous page to keep it easily accessible. This information is available in the sections "Service and maintenance" and "Technical data" as well as on the identification plate.
4 Introduction 9 Warning Text marked 9 Warning provides information on risk of accident or injury. Disregarding this information may lead to injury. Caution Text marked Caution provides information on possible damage to the vehicle. Disregarding this information may lead to vehicle damage.
Introduction 5.
6 In brief In brief Initial drive information Vehicle unlocking Press button q to unlock the doors and load compartment. Open the doors by pulling the handles. To open the tailgate, operate button above number plate. Radio remote control 3 19, Central locking system 3 20, Load compartment 3 22.
In brief 7 Seat backrests Pull lever, adjust inclination and release lever. Allow the backrest to engage audibly. Do not lean on the seat backrest whilst adjusting it. Seat position 3 34, Seat adjustment 3 35. Seat height Lever pumping motion up = seat higher down = seat lower Seat position 3 34, Seat adjustment 3 35.
8 In brief Positioning = move front switch forwards/backwards Height of front part of seat = move front part of front switch upwards/ downwards Height of rear part of seat = move rear part of front sw.
In brief 9 Mirror adjustment Interior mirror To reduce dazzle, adjust the lever on the underside of the mirror housing. Interior mirror 3 28, Automatic anti- dazzle interior mirror 3 28. Exterior mirrors Select the relevant exterior mirror and adjust it.
10 In brief Instrument panel overview.
In brief 11 1 Side air vents ..................... 114 2 Fixed air vents .................... 114 3 High beam .......................... 103 Headlight flash ................... 103 Turn and lane-change signals ................................ 105 Exit lighting .
12 In brief Exterior lighting Turn light switch AUTO = Automatic light control: Headlights are switched on and off automatically. 7 = Off (or deactivation of automatic light control) 8 = Sidelights 9 = Headlights Press button > = Front fog lights r = Rear fog light Lighting 3 102.
In brief 13 Hazard warning flashers Operated with the ¨ button. Hazard warning flashers 3 104. Horn Press j . Washer and wiper systems Windscreen wiper & = fast % = slow $ = timed interval wiping or automatic wiping with rain sensor § = off For a single wipe when the windscreen wiper is off, press the lever down.
14 In brief Windscreen and headlight washer systems Pull lever. Windscreen and headlight washer system 3 71, Washer fluid 3 147. Rear window wiper and washer system Wiper on = push lever Wiper off = pull lever Wash = press and hold button Rear window wiper and washer system 3 73, Wiper blade replacement 3 151, Washer fluid 3 147.
In brief 15 Demisting and defrosting the windows Air distribution to l . Cooling n and air recirculation 4 are switched on automatically to improve defrosting efficiency. Set temperature to highest level. Set fan speed to highest level. Switch on heated rear window Ü .
16 In brief Starting off Check before starting off ■ Tyre pressure and condition 3 168, 3 198. ■ Engine oil level and fluid levels 3 145. ■ All windows, mirrors, exterior lighting and number plates are free from dirt, snow and ice and are operational.
In brief 17 Parking ■ Always apply the electrical parking brake. Pull switch m . For maximum force, e.g. parking with a trailer or on inclines, pull switch m twice. ■ Switch off the engine and turn the ignition key to position LOCK , push key into ignition switch and remove.
18 Keys, doors and windows Keys, doors and windows Keys, locks ................................... 18 Doors ........................................... 22 Vehicle security ............................ 23 Exterior mirrors ............................ 26 Interior mirrors .
Keys, doors and windows 19 Radio remote control Used to operate: ■ Central locking system ■ Anti-theft locking system ■ Anti-theft alarm system The radio remote control has a range of approx. 6 metres. This range can be affected by outside influences.
20 Keys, doors and windows Key with fixed key section Open the unit with a small screwdriver in the notch on the cover. Replace the battery (battery type CR2032), paying attention to the installation position. Close the unit. Central locking system Unlocks and locks doors, load compartment and fuel filler flap.
Keys, doors and windows 21 Unlocking the tailgate Press button q . The tailgate is unlocked together with the doors. With the engine running, the tailgate will only unlock when the electrical parking brake is applied or automatic transmission is in position P .
22 Keys, doors and windows Doors Load compartment Tailgate Opening Operate the button above the number plate and lift the tailgate. If the tailgate is open when the ignition is switched on, control indicator 1 illuminates in the instrument cluster 3 88.
Keys, doors and windows 23 Fault To open the tailgate in the event of power interruption: Remove the interior trim cover from the central latch area, then push the lever using a suitable tool. Vehicle security Anti-theft locking system 9 Warning Do not use the system if there are people in the vehicle! The doors cannot be unlocked from the inside.
24 Keys, doors and windows ■ Siren power supply ■ Ignition Activation Ensure the doors, tailgate, fuel filler flap, bonnet, windows and sunroof are closed.
Keys, doors and windows 25 3. Close doors. 4. Activate the anti-theft alarm system. Press button o again to cancel. Control indicator o extinguishes. Status LED Status LED is located in the centre console. Status during the first 30 seconds of anti-theft alarm system activation: LED illuminates = test, arming delay.
26 Keys, doors and windows Immobiliser The system is integrated into the ignition switch and checks whether the vehicle is allowed to start with the key being used. If the transponder in the key is recognized, the engine can be started. The electronic immobiliser is activated automatically after the key has been removed from the ignition switch.
Keys, doors and windows 27 Folding For pedestrian safety, the exterior mirrors will swing out of their normal mounting position if they are struck with sufficient force. Reposition the mirror by applying slight pressure to the mirror housing. Manual folding Press lightly on the outside of the mirror housing to fold in the exterior mirrors.
28 Keys, doors and windows Do not use sharp instruments or abrasive cleaners on the exterior mirrors and avoid scratching or damaging the heating elements. Interior mirrors Manual anti-dazzle To reduce dazzle, adjust the lever on the underside of the mirror housing.
Keys, doors and windows 29 Windows Windscreen Heat-reflecting windscreen The heat-reflecting windscreen has a coating which reflects solar radiation. Also data signals, e.g. from toll stations, might be reflected. The marked areas of the windscreen behind the interior mirror are not covered with the coating.
30 Keys, doors and windows Additional switches are located in the front passenger's door and the rear doors. The rear windows do not open fully. Safety function If the window glass encounters resistance above the middle of the window during automatic closing, it is immediately stopped and opened again.
Keys, doors and windows 31 Do not use sharp instruments or abrasive cleaners on the rear window and avoid scratching or damaging the heating elements. Sun visors The sun visors can be folded down or swivelled to the side to prevent dazzling. Sun visors have vanity mirrors and a ticket holder on the rear.
32 Keys, doors and windows General hints Function standby The sunroof can be operated: ■ with ignition on, ■ within 10 minutes of switching ignition off, After switching off the ignition, sunroof operation is disabled when driver's door is opened.
Seats, restraints 33 Seats, restraints Head restraints ............................ 33 Front seats ................................... 34 Rear seats ................................... 38 Seat belts ..................................... 39 Airbag system .
34 Seats, restraints Stow head restraints securely in load compartment. Active head restraints on front seats In the event of a rear-end impact, the active head restraints automatically tilt forwards. The head is more effectively supported by the head restraint and the risk of whiplash injury is reduced.
Seats, restraints 35 Seat adjustment 9 Danger Do not sit nearer than 25 cm from the steering wheel, to permit safe airbag deployment. 9 Warning Never adjust seats while driving as they could move uncontrollably. Seat positioning Pull handle, slide seat, release handle.
36 Seats, restraints Lumbar support Adjust lumbar support to suit personal requirements using the lever. To increase or decrease lumbar support, move lever forwards or backwards. Seat folding Push head restraint all the way down. Slide seat as far back as it will go.
Seats, restraints 37 Seat positioning Move front switch forwards/ backwards. Seat height Move front of switch upwards/ downwards to adjust height of front part of seat cushion. Move rear of switch upwards/ downwards to adjust height of rear part of seat cushion.
38 Seats, restraints If temperature continues to rise, turn seat heating off and seek the assistance of a workshop. Rear seats Seat backrests To adjust seat backrests, lift release lever on top of backrest and move backrest forwards/backwards to desired position.
Seats, restraints 39 Push head restraints all the way down, lift backrest release lever and fold backrest forwards and down onto seat cushion. Do not allow passengers to sit on a folded backrest, or place any unrestrained loads on it. To move backrest to its original position, lift and push the backrest into place and ensure the backrest engages.
40 Seats, restraints Seat belts are designed to be used by only one person at a time. They are not suitable for people smaller than 150 cm. Child restraint system 3 47. Periodically check all parts of the belt system for damage and proper functionality.
Seats, restraints 41 Loose or bulky clothing prevents the belt from fitting snugly. Do not place objects such as handbags or mobile phones between the belt and your body. 9 Warning The belt must not rest against hard or fragile objects in the pockets of your clothing.
42 Seats, restraints Removing To release belt, press red button on belt buckle. Using the seat belt while pregnant 9 Warning The lap belt must be positioned as low as possible across the pelvis to prevent pressure on the abdomen.
Seats, restraints 43 Airbag system The airbag system consists of a number of individual systems depending on the scope of equipment. When triggered the airbags inflate within milliseconds. They also deflate so quickly that it is often unnoticeable during the collision.
44 Seats, restraints The inflated airbags cushion the impact, thereby considerably reducing the risk of injury to the upper body and head of the front seat occupants. 9 Warning Optimum protection is only provided when the seat is in the proper position 3 34.
Seats, restraints 45 Curtain airbag system The curtain airbag system consists of an airbag in the roof frame on each side. This can be identified by the word AIRBAG on the roof pillars. The curtain airbag system is triggered in the event of a side-on impact of a certain severity.
46 Seats, restraints Use the ignition key to choose the position: * OFF = front passenger airbag systems are deactivated and will not inflate in the event of a collision. Control indicator * illuminates continuously on the passenger side of the instrument panel.
Seats, restraints 47 Child restraints Child restraint systems We recommend the Vauxhall child restraint system which is tailored specifically to the vehicle. When a child restraint system is being used, pay attention to the following usage and installation instructions and also those supplied with the child restraint system.
48 Seats, restraints Child restraint installation locations Permissible options for fitting a child restraint system Weight and age class On front passenger seat On rear outboard seats On rear centre seat activated airbag deactivated airbag Group 0: up to 10 kg or approx.
Seats, restraints 49 Permissible options for fitting an ISOFIX child restraint system Weight and age class Size class Fixture On front passenger seat On rear outboard seats On rear centre seat Group 0: up to 10 kg or approx. 10 months E ISO/R1 X IL X Group 0+: up to 13 kg or approx.
50 Seats, restraints ISOFIX size class and seat device A - ISO/F3 = Forward-facing child restraint system for children of maximum size in the weight class 9 to 18 kg. B - ISO/F2 = Forward-facing child restraint system for smaller children in the weight class 9 to 18 kg.
Seats, restraints 51 ISOFIX child restraint systems Fasten vehicle-approved ISOFIX child restraint systems to the ISOFIX mounting brackets. Permitted installation positions for specific vehicle ISOFIX child restraint systems are marked in the table by IL.
52 Storage Storage Storage compartments ................ 52 Load compartment ....................... 63 Roof rack system ......................... 68 Loading information ..................... 68 Storage compartments Glovebox The glovebox will illuminate when opened.
Storage 53 Located in the front passenger foot well. Coin storage Pull handle to open. Push door firmly to close. Card holder Located above the coin storage compartment. A card can be retained in the slot for convenient use. Sunglasses storage To open: push the rear part of the cover.
54 Storage Armrest storage Console box in front armrest To open: pull up lever and lift the lid. To close: lower lid and push it down until it latches into position. Centre console storage To access the storage compartment, cigarette lighter and AUX input, slide the cupholder tray rearwards.
Storage 55 Raise release lever. The system disengages and travels quickly out of the bumper. Completely pull out the rear carrier system until it engages. Ensure that it is not possible to push in the rear carrier system without pulling the release lever again.
56 Storage Open out the bulb holder on the back of the tail lamp completely. Push the clamping lever and push the bulb holder into the retainer until it hits the stop. Perform this procedure for both tail lamps. Check the cable and lamp position to make sure these are correctly installed and are securely located.
Storage 57 Unfold pedal crank recesses Fold one or both pedal crank recesses upwards until the diagonal support engages. Remove the pedal crank mounts from the pedal crank recesses.
58 Storage If the bicycle has curved pedal cranks, screw in the pedal crank unit all the way (position 1 ). Press the release lever and withdraw the wheel recesses.
Storage 59 Attaching a bicycle to the rear carrier system Put on the bicycle. The pedal crank here must be placed in the pedal crank recess opening as shown in the illustration. Caution Make sure that the pedal does not touch the surface of the rear end carrier.
60 Storage Align the bicycle in the longitudinal direction of the vehicle: Slightly loosen the pedal mount. Place the bicycle upright using the rotary lever on the pedal crank recess.
Storage 61 Removing a bicycle from the rear carrier system Undo strap retainers on both bicycle tyres. Hold on to the bicycle, loosen the attachment screw for the pedal bearing mount, then lift the pedal bearing mount to remove it.
62 Storage Press release lever and slide in wheel recesses all the way as far as they will go. Disengage the locking lever on the diagonal support and fold both pedal crank recesses down.
Storage 63 Pull up license plate holder and fold down into horizontal position. Open the tailgate. Raise the release lever up and push the system into the bumper until it engages. Release lever must return to original position. 9 Warning If the system cannot be correctly engaged, please seek the assistance of a workshop.
64 Storage Closing the cover Pull load compartment cover towards rear of vehicle using handle and insert retainers into brackets on either side of load compartment. Opening the cover Remove load compartment cover from side brackets. The cover rolls up automatically.
Storage 65 Hang the hook to the upper part of the tailgate opening. Caution Do not allow objects to protrude above the top of the rear floor storage compartment, to avoid damage to the storage area and the load compartment floor. Jack and vehicle tools 3 165.
66 Storage Variable partition net Insert an adapter into each rail: fold open the handle plate, insert adapter into upper and lower groove of rail and move to required position.
Storage 67 When fitting in front of the rear seats, push head restraints of the rear seats down and fold down rear seat backrests 3 38. Open aperture covers on the roof frame and insert top corners of safety net into large apertures in roof frame and secure by sliding them into the smaller apertures.
68 Storage Roof rack system Roof rack For safety reasons and to avoid damage to the roof, the vehicle approved roof rack system is recommended. Fasten the roof rack to the roof rails following the instructions that accompany the system, ensuring that the roof load is evenly distributed over the side or cross rails.
Storage 69 vehicle weight (see identification plate 3 189) and the EC kerb weight. To calculate the EC kerb weight, enter the data for your vehicle in the Weights table at the front of this manual. The EC kerb weight includes weights for the driver (68 kg), luggage (7 kg) and all fluids (tank 90 % full).
70 Instruments and controls Instruments and controls Controls ....................................... 70 Warning lights, gauges and indicators ..................................... 77 Information displays ..................... 88 Vehicle messages ....
Instruments and controls 71 Horn Press j . Windscreen wiper/washer Windscreen wiper & = fast % = slow $ = timed interval wiping or automatic wiping with rain sensor § = off For a single wipe when the windscreen wiper is off, press the lever down.
72 Instruments and controls In this mode, wiping frequency is also affected by vehicle speed. As vehicle speed increases, wiping will become more frequent.
Instruments and controls 73 Control indicator G illuminates in the instrument cluster when the washer fluid level is low. Wiper activated lighting With light switch in the AUTO position, when the windscreen wiper is operated for 8 cycles or more the exterior lights illuminate automatically.
74 Instruments and controls 9 Warning The road surface may already be icy even though the display indicates a few degrees above 0 °C. Clock Date and time are shown in the Info-Display. Board-Info-Display 3 88. Graphic-Info-Display, Colour-Info-Display 3 91.
Instruments and controls 75 Deactivate ( Clock Sync.Off ) or activate ( Clock Sync.On ) automatic time synchronisation with the arrow buttons on the Infotainment system. To set date and time manually, select the menu item for time and date setting from the Settings menu and make the desired setting.
76 Instruments and controls A 12 Volt power outlet is located in the rear centre console and on the right- hand side of the load compartment. Pull the cap out to use the accessory socket, and replace the cap when not in use. Do not exceed the maximum power consumption of 120 watts.
Instruments and controls 77 To replace battery: remove screw on ashtray lid and replace with CR 2032 (or equivalent) battery. Warning lights, gauges and indicators Speedometer Indicates vehicle speed. Odometer The bottom line displays the recorded distance.
78 Instruments and controls Tachometer Displays the engine speed. Drive in a low engine speed range for each gear as much as possible. Caution If the needle is in the red warning zone, the maximum permitted engine speed is exceeded. Engine at risk. Fuel gauge Displays the fuel level in the tank.
Instruments and controls 79 When the ignition is switched on, most control indicators will illuminate briefly as a functionality test. The control indicator colours mean: red = danger, important remin.
80 Instruments and controls Control indicators in the instrument cluster.
Instruments and controls 81 Turn signal O illuminates or flashes green. The relevant control indicator flashes when the turn signal is switched on 3 105. Rapid flashing: failure of a turn signal bulb or the associated fuse or failure of a turn signal light on trailer.
82 Instruments and controls Illuminates when the ignition is switched on and extinguishes shortly after the engine starts. If it does not illuminate, seek the assistance of a workshop. Can illuminate briefly when driving; this is normal and does not indicate a system fault.
Instruments and controls 83 When the engine is started, m illuminates briefly. If it does not illuminate, seek the assistance of a workshop. Illuminates Electrical parking brake is applied 3 129. Flashes Electrical parking brake is not fully applied or released.
84 Instruments and controls Green Illuminates when system is ready for operation. Flashes during driving when system is in operation, after pressing the u button. Yellow Flashes to indicate system is not ready for conditions to operate. Illuminates to indicate there is a fault in the system.
Instruments and controls 85 Engine coolant temperature W illuminates red. When the engine is started, W illuminates briefly. If it does not illuminate, seek the assistance of a workshop. Illuminates when the engine is running Stop vehicle and switch off engine.
86 Instruments and controls 9 Warning When the engine is off, considerably more force is needed to brake and steer. Do not remove key until vehicle is stationary, otherwise the steering wheel lock could engage unexpectedly. Check oil level before seeking the assistance of a workshop 3 145.
Instruments and controls 87 Residual water in the diesel fuel filter must be drained 3 150. Seek the assistance of a workshop as soon as possible. Immobiliser d illuminates red. When the engine is started, d illuminates briefly. If it does not illuminate, seek the assistance of a workshop.
88 Instruments and controls control indicator W flashes, accompanied by a warning chime, to warn the driver to reduce speed as appropriate. Trailer indicator g illuminates green. Illuminates when a trailer is connected to the vehicle 3 139. Bonnet open / illuminates red.
Instruments and controls 89 The Info-Display is located in the instrument panel above the Infotainment system. An F in the display indicates a fault. Have the cause of the fault remedied by a workshop. Trip computer, Board-Info-Display 3 97. Selecting functions Functions and settings of the Infotainment system can be accessed via the Info-Display.
90 Instruments and controls System settings Press the Settings button of the Infotainment system. Menu item Audio then opens. Call up System with the left arrow button and select with the OK button. The first function of the System menu is highlighted.
Instruments and controls 91 The value ready for modification is marked with arrows. Use the arrow buttons to make the required setting. The setting is saved when the menu item is exited. Ignition logic See Infotainment system instruction manual. Language selection The display language for some functions can be selected.
92 Instruments and controls The type of information and how it is displayed depends on the equipment of the vehicle and the settings of the trip computer and Infotainment system. Some information appears on the display in an abbreviated form. An F in the display indicates a fault.
Instruments and controls 93 Select using the left adjuster wheel on the steering wheel Turn the adjuster wheel to call up the required function. Press the adjuster wheel to select marked items and confirm commands. Press to operate the stop watch or restart measurement and calculation.
94 Instruments and controls ■ Contrast ■ Day / Night ■ Ignition logic Setting date and time With the navigation system, date and time are set automatically upon receipt of a GPS satellite signal. If the displayed time does not match local time, it can be corrected manually or automatically by receiving an RDS time signal.
Instruments and controls 95 Select the desired language. Selections are indicated by a 6 in front of the menu item. In systems with voice output, when the language setting of the display is changed, the system will ask whether the announcement language should also be changed – see Infotainment system instruction manual.
96 Instruments and controls Always day design ; black or coloured text on a light background. Always night design ; white or coloured text on a dark background. Selections are indicated by a o in front of the menu item. Ignition logic See Infotainment system instruction manual.
Instruments and controls 97 Reduce speed and check tyre pressure at the next opportunity. Tyre pressure monitoring system 3 168. Check tyre pressures 3 168, 3 198. If there is a considerable loss of pressure, a corresponding message appears indicating the relevant tyre.
98 Instruments and controls Average consumption Display of average consumption. The measurement can be reset at any time. Effective consumption Display of the amount of fuel consumed. The measurement can be reset at any time. Average speed Display of average speed.
Instruments and controls 99 Interruption of power supply If the power supply has been interrupted or if the battery voltage has dropped too low, the values stored in the trip computer will be lost.
100 Instruments and controls Instantaneous consumption Display of the instantaneous consumption. Display changes depending on speed: Display in gal/h = below 8 mph Display in miles/gal = above 8 mph Distance travelled Display of distance travelled. The measurement can be reset at any time.
Instruments and controls 101 Stop watch Select menu item Timer from the Board Computer menu. The Timer menu is displayed. To start, select menu item Start . To reset, select menu item Reset . The desired stop watch display can be selected from the Options menu: Driving Time excl.
102 Lighting Lighting Exterior lighting .......................... 102 Interior lighting ........................... 107 Lighting features ........................ 109 Exterior lighting Light switch Turn light switch: AUTO = Automatic light control: Headlights are switched on and off automatically depending on external lighting conditions.
Lighting 103 To ensure automatic light control functions properly, do not cover the light sensor on top of the instrument panel. Daytime running lights Daytime running lights increase visibility of the vehicle during daylight. The lights operate automatically when the ignition is switched on.
104 Lighting Vehicles without automatic level control system Turn thumb wheel to required position: 0 = front seats occupied 1 = all seats occupied 2 = all seats occupied and load compartment laden 3 .
Lighting 105 Turn and lane-change signals lever up = right turn signal lever down = left turn signal If the lever is moved past the resistance point, the turn signal is switched on constantly. When the steering wheel is turned back, the turn signal is automatically deactivated.
106 Lighting Rear fog lights Operated with the r button. Control indicator r illuminates in the instrument cluster when the rear fog light is switched on. The rear fog light can only be switched on when the ignition is on and the light switch is in position 9 , or the front fog lights are on and the light switch is in position 8 .
Lighting 107 Interior lighting Instrument panel illumination control The instrument panel illuminates when the ignition is switched on. Brightness can be adjusted when the exterior lights are on: Turn thumb wheel to the right or left until the desired brightness is obtained.
108 Lighting Switch off immediately by pressing button K in the roof lining. Ashtray illumination The portable front ashtray, located in the front drink holder, illuminates depending on outside light conditions. Glovebox illumination Illuminates when the glovebox is opened.
Lighting 109 Lighting features Entry lighting Welcome lighting Depending upon outside light conditions, when unlocking the vehicle with the remote control the hazard warning lights flash twice and the exterior and interior lights illuminate for 20 seconds.
110 Climate control Climate control Climate control systems ............. 110 Air vents ..................................... 114 Maintenance .............................. 115 Climate control systems Heating and ventilation system Controls for: ■ Temperature ■ Air distribution ■ Fan speed Heated rear window Ü 3 30.
Climate control 111 Air conditioning system In addition to the heating and ventilation system, the air conditioning system has: n = cooling 4 = air recirculation Ü = demisting and defrosting Cooling n Operated with the n button and is functional only when the engine and fan are running.
112 Climate control ■ Set the air distribution switch to l or J . ■ Set temperature control to warmest level. ■ Set fan to highest level. ■ Close centre air vents. ■ Open side air vents and direct them towards the door windows. ■ Switch on heated rear window Ü 3 30.
Climate control 113 Recommended comfort setting is 22 °C. Intermediate settings are possible. To deactivate automatic mode, turn fan to position off x . All air vents are actuated automatically in automatic mode. The air vents should therefore always be open.
114 Climate control Air vents Adjustable air vents To open and close the vents, turn the horizontal adjuster wheel to the left or right. Open air vents when air distribution switch is set to M or L . The air supply is increased by switching on the fan.
Climate control 115 Maintenance Air intake The air intakes in front of the windscreen in the engine compartment must be kept clear to allow air intake. Remove any leaves, dirt or snow. Pollen filter Cabin air filtration A particle filter cleans the cabin air from dust, soot, pollen and spores.
116 Driving and operating Driving and operating Driving hints ............................... 116 Starting and operating ............... 116 Engine exhaust .......................... 120 Automatic transmission .............. 122 Manual transmission ..
Driving and operating 117 Ignition switch positions LOCK = Ignition off ACC = Steering wheel lock released, ignition off ON = Ignition on, for diesel engine: preheating START = Starting Starting the engine Manual transmission: operate clutch and brake pedals.
118 Driving and operating Ensure the engine oil is of the correct viscosity, the correct fuel is used, vehicle services are performed regularly and the battery is sufficiently charged. Stop-start system The stop-start system helps to save fuel and to reduce the exhaust emissions.
Driving and operating 119 Conditions for an Autostop The stop-start system checks if each of the following conditions is fulfilled. Otherwise an Autostop will be inhibited.
120 Driving and operating For maximum force, e.g. parking with a trailer or on inclines, pull switch m twice. ■ Switch off the engine and turn the ignition key to position LOCK , push key into ignition switch and remove. Turn the steering wheel until the steering wheel lock is felt to engage.
Driving and operating 121 The filter is cleaned by periodically burning off the soot particles at high temperature. This process takes place automatically under set driving conditions and may take up to 15 minutes. Fuel consumption may be higher during this period.
122 Driving and operating Caution Fuel grades other than those listed on pages 3 136, 3 193 could damage the catalytic converter or electronic components. Unburnt petrol will overheat and damage the catalytic converter. Therefore avoid excessive use of the starter, running the fuel tank dry and starting the engine by pushing or towing.
Driving and operating 123 The selector lever is locked in position P and N and can only be moved when the ignition is on and the foot brake is applied. To engage P or R , push the release button. Never shift to P or R while the vehicle is moving. The engine can only be started with lever in position P or N .
124 Driving and operating transmission will automatically shift to a lower gear, even in manual mode, to prevent the engine from stalling. If a higher gear is selected when vehicle speed is too low, or a lower gear when vehicle speed is too high, the shift is not executed.
Driving and operating 125 Deactivation Fuel economy mode is switched off by pressing button s again; control indicator s extinguishes in the instrument cluster. Fault In the event of a fault in the automatic transmission, control indicator Z illuminates in the instrument cluster 3 81.
126 Driving and operating Manual transmission Reverse: with the vehicle stationary, wait 3 seconds after depressing clutch pedal and engage the gear. If the gear does not engage, set the lever to neutral, release the clutch pedal and depress again; then repeat gear selection.
Driving and operating 127 Ensure tyres (including the spare) are inflated to the correct pressure 3 198 and are suitable for the prevailing road conditions. For optimum system performance, the vehicle's tyres should not have varying degrees of wear.
128 Driving and operating operations for wading , involving checks for water contamination, at the earliest opportunity. Service checks after wading Check for the ingress of water into the following: .
Driving and operating 129 Brakes The brake system comprises two independent brake circuits. If a brake circuit fails, the vehicle can still be braked using the other brake circuit. However, braking effect is achieved only when the brake pedal is depressed firmly.
130 Driving and operating Applying when vehicle is stationary Pull switch m , the electrical parking brake operates automatically with adequate force. For maximum force, e.g. parking with a trailer or on inclines, pull switch m twice. The electrical parking brake can always be activated, even if the ignition is off.
Driving and operating 131 movement. Seek the assistance of a workshop to have the cause of the fault remedied. Brake assist If the brake pedal is depressed quickly and forcefully, maximum brake force is automatically applied (full braking). Maintain steady pressure on the brake pedal for as long as full braking is required.
132 Driving and operating Switch off ESC function, to allow engine rpm to increase, by pressing button t briefly. Control indicator t illuminates in the instrument cluster. ESC is reactivated by pressing button t again. The control indicator extinguishes.
Driving and operating 133 Deactivation Press button u again. The green control indicator u extinguishes. Depressing the foot brake or accelerator will also cause the system to be deactivated. Fault The yellow control indicator u flashes to indicate that the system is not ready for conditions to operate, due to the high temperature (approx.
134 Driving and operating With automatic transmission, only activate cruise control in automatic mode. Control indicator m 3 87. Activation Press the e button; control indicator m illuminates yellow in the instrument cluster. Accelerate to the desired speed, press the - SET button and release it.
Driving and operating 135 Object detection systems Parking assist The parking assist system makes parking easier by measuring the distance between the vehicle and obstacles to the front and rear, and giving acoustic signals. It is the driver, however, who bears full responsibility for the parking manoeuvre.
136 Driving and operating If the acoustic signal sounds 3 times continuously when there are no obstacles near the front or rear bumper, there is a fault in the system.
Driving and operating 137 Caution Use of fuel with too low an octane rating could lead to uncontrolled combustion and engine damage. Fuel for ethanol adapted engines (E85) If access to E85 is limited then fuel with a different proportion of ethanol or normal RON 95 can be used for refuelling.
138 Driving and operating 9 Danger Fuel is flammable and explosive. No smoking. No naked flames or sparks. If you can smell fuel in your vehicle, have the cause of this remedied immediately by a workshop. Caution In case of misfuelling, do not switch on ignition.
Driving and operating 139 General information The official fuel consumption and specific CO 2 emission figures quoted relate to the EU base model with standard equipment. Fuel consumption data and CO 2 emission data are determined according to regulation R (EC) No.
140 Driving and operating When driving downhill, drive in the same gear as if driving uphill and drive at a similar speed. Adjust tyre pressure to the value specified for full load 3 198. Trailer towing Trailer loads The permissible trailer loads are vehicle-dependent and engine- dependent maximum values which must not be exceeded.
Driving and operating 141 Towing equipment Caution When operating without a trailer, remove the coupling ball bar. Towing equipment with detachable coupling ball bar The coupling ball bar is kept in a bag, fastened with a strap and is stowed below the floor cover in the load compartment.
142 Driving and operating Lock coupling ball bar by turning the supplied key in the lock cylinder of the coupling ball bar. Remove key. Check that the coupling ball bar is correctly attached: ■ Green marking must be visible on lever. ■ Coupling ball bar must be seated firmly in coupling housing.
Vehicle care 143 Vehicle care General Information ................... 143 Vehicle checks ........................... 144 Bulb replacement ....................... 151 Electrical system ........................ 157 Vehicle tools ........................
144 Vehicle care Putting back into operation When the vehicle is to be put back into operation: ■ Connect the clamp to the negative terminal of the vehicle battery. Activate the electronics of the power windows. ■ Check tyre pressure. ■ Fill up the washer fluid reservoir.
Vehicle care 145 Locate the safety catch, found slightly left of centre on the underside of the bonnet, push the catch upwards and lift the bonnet gently. The bonnet is held open automatically. Air intake 3 115. Closing Lower the bonnet and allow it to drop into the catch.
146 Vehicle care We recommend the use of the same grade of engine oil that was used at the last oil change. The engine oil level must not exceed the MAX mark on the dipstick. Caution Overfilled engine oil must be drained or suctioned out. Capacities 3 197, Engine oil quality/ viscosity 3 186.
Vehicle care 147 the coolant concentration checked and have the cause of the coolant loss remedied by a workshop. Engine coolant temperature control indicator W 3 85. Power steering fluid If the fluid level in the reservoir falls below the MIN mark, seek the assistance of a workshop.
148 Vehicle care The brake fluid level must be between the MIN and MAX marks. When topping up, ensure maximum cleanliness as contamination of the brake fluid can lead to brake system malfunctions. Have the cause of the loss of brake fluid remedied by a workshop.
Vehicle care 149 Retrofitted electrical or electronic accessories can place an additional load on the battery or discharge the battery. Seek the assistance of a workshop regarding technical possibilities, such as fitting a more powerful battery. Ensure the ignition is switched off before reconnecting the battery.
150 Vehicle care Charging the battery 9 Warning On vehicles with stop-start system, ensure that the charging potential does not exceed 14.6 volts when using a battery charger. Otherwise the battery might be damaged. Jump starting 3 178. Warning label Meaning of symbols: ■ No sparks, naked flames or smoking.
Vehicle care 151 operation 3 times or more while the engine is switched off, to avoid air entering the fuel line. Check diesel fuel filter at shorter intervals if the vehicle is subjected to extreme operating conditions. If there is water in the diesel fuel filter, control indicator N illuminates in the instrument cluster 3 86.
152 Vehicle care 1. Switch off the ignition and headlight switch. 2. Open the bonnet, release the 11 retainers and remove the radiator cover. 3. Remove 3 bolts and withdraw headlamp. 4. Depress harness connector tags and disconnect headlamp wiring. 5.
Vehicle care 153 5. Engage bulb retaining spring and replace headlamp cap. 6. Reinstall headlamp assembly. Front turn signal 1. Remove headlamp assembly 3 151. 2. Rotate bulb holder anticlockwise and withdraw bulb holder from lamp assembly. 3. Press and rotate bulb anticlockwise to remove it from bulb holder.
154 Vehicle care Low and high beam 9 Danger Xenon headlights work under extremely high electrical voltage. Do not touch. Have bulbs replaced by a workshop. Front turn signal 1. Remove headlamp assembly 3 151. 2. Rotate bulb holder anticlockwise and withdraw bulb holder from lamp assembly.
Vehicle care 155 1. Remove 2 screws from panel on underside of vehicle below front fog lights and remove panel. 2. Disconnect harness connector from bulb holder and rotate bulb holder anticlockwise. 3. Remove bulb holder from lamp assembly, rotate bulb anticlockwise and remove from bulb holder.
156 Vehicle care Side turn signal lights 1. Using a suitable screwdriver, pry lamp assembly away from wing. 2. Rotate bulb holder anticlockwise. 3. Remove bulb from lamp assembly by pulling bulb straight out of bulb holder. 4. Insert new bulb into bulb holder by pressing it in and rotating the bulb holder clockwise.
Vehicle care 157 Rear reading lights 1. Using a suitable screwdriver, pry lamp lens away from roof lining. 2. Remove bulb. 3. Insert new bulb. 4. Reinstall lamp lens in roof lining. Load compartment light 1. Using a suitable screwdriver, remove lens from lamp assembly.
158 Vehicle care It is advisable to carry a full set of spare fuses. Spare fuses can be stored in the engine compartment fuse box. Fuse extractor A fuse extractor may be located in the engine compartment fuse box. Place the fuse extractor on the various types of fuse from the top or side, and withdraw fuse.
Vehicle care 159 Engine compartment fuse box The fuse box is located next to the coolant reservoir in the engine compartment. To open, disengage cover and tilt upwards.
160 Vehicle care.
Vehicle care 161 Fuse Circuit ABS Anti-lock Brake System A/C Climate control, air conditioning system BATT1 Instrument panel fuse box BATT2 Instrument panel fuse box BATT3 Instrument panel fuse box BC.
162 Vehicle care After changing of defective fuses close the fuse box cover and press until it engages. If the fuse box cover is not closed correctly, malfunctions may occur.
Vehicle care 163.
164 Vehicle care Fuse Circuit AMP Amplifier APO JACK (CONSOLE) Power outlet (centre console) APO JACK (REAR CARGO) Power outlet (load compart‐ ment) AWD/VENT All-wheel drive, ventilation BCM (CTSY) .
Vehicle care 165 Fuse Circuit RUN 2 Power battery key on run RUN/CRNK Run crank SDM (BATT) Safety Diag‐ nosis Module (Battery) SDM (IGN 1) Safety Diag‐ nosis Module (Ignition) SPARE - S/ROOF Sunro.
166 Vehicle care The jack and vehicle tools are in a storage compartment below the floor cover in the load compartment. To remove the jack and vehicle tools, open the tailgate. Push both levers on the floor cover towards the handle and pull up the floor cover by the handle.
Vehicle care 167 the floor cover by the handle. Hang the hook to the upper part of the tailgate opening. Caution Do not allow objects to protrude above the top of the rear floor storage compartment, to avoid damage to the storage area and the load compartment floor.
168 Vehicle care 104 = Load index e.g. 91 is equivalent to 618 kg H = Speed code letter Speed code letter: Q = up to 100 mph S = up to 112 mph T = up to 118 mph H = up to 130 mph V = up to 150 mph W = up to 168 mph Tyre pressure Check the pressure of cold tyres at least every 14 days and before any long journey.
Vehicle care 169 pressures are detected. In some versions, the message is displayed in abbreviated form. For example, the following messages can be displayed: A graphic indicating the left rear tyre is shown together with the current tyre pressure; slight pressure deviation.
170 Vehicle care The legally permissible minimum tread depth (1.6 mm) has been reached when the tread has worn down as far as one of the tread wear indicators (TWI). Their position is indicated by markings on the sidewall. If there is more wear at the front than the rear, swap round front wheels and rear wheels.
Vehicle care 171 Tyre chains Tyre chains are only permitted on the front wheels. They must be fitted to the tyres symmetrically in order to achieve a concentric fit. Always use fine mesh chains that add no more than 15 mm to the tyre tread and the inboard sides (including chain lock).
172 Vehicle care Caution Do not allow objects to protrude above the top of the rear floor storage compartment, to avoid damage to the storage area and the load compartment floor. 1. Release the sealant filler hose 1 and the power plug 2 . 2. Unscrew valve cap from defective tyre.
Vehicle care 173 is obtained, switch off the compressor. If the prescribed tyre pressure is not obtained within 10 minutes, remove the tyre repair kit. Move the vehicle one tyre rotation. Reattach the tyre repair kit and continue the filling procedure for 10 minutes.
174 Vehicle care 13. Turn the selector switch clockwise to the air only position. Switch on the compressor to inflate the tyre with air only. Notice The driving characteristic of the repaired tyre is severely affected, therefore have this tyre replaced.
Vehicle care 175 ■ Do not raise the vehicle more than is necessary to change a wheel. ■ No people or animals may be in the vehicle when it is jacked-up. ■ Never crawl under a jacked-up vehicle. ■ Do not start the engine when it is raised on the jack.
176 Vehicle care 5. Attach wheel wrench to eye of threaded rod and rotate wrench clockwise to raise vehicle. If this is not the case, carefully lower the vehicle immediately and reposition the jack. Raise the vehicle until the wheel is just clear of the ground.
Vehicle care 177 Front arm position of the lifting platform centrically under the recess of the sill. Spare wheel Temporary spare wheel Some vehicles are equipped with a tyre repair kit instead of a spare wheel. The temporary spare wheel is designed for use on your vehicle only.
178 Vehicle care The following applies to tyres fitted opposing the rolling direction: ■ Driveability may be affected. Have the defective tyre renewed as soon as possible and have the wheel balanced and fitted to the vehicle. ■ Do not drive faster than 50 mph.
Vehicle care 179 ■ A discharged battery can already freeze at a temperature of 0 °C. Defrost the frozen battery before connecting jump leads. ■ Wear eye protection and protective clothing when handling a battery. ■ Use a booster battery with the same voltage (12 Volts).
180 Vehicle care 4. Switch on electrical consumers (e.g. headlights, heated rear window) of the vehicle receiving the jump start. 5. Operate discharged vehicle for approx. 20 minutes to allow for adequate battery recharging. 6. Reverse above sequence exactly when removing leads.
Vehicle care 181 To prevent the entry of exhaust fumes from the towing vehicle, switch on the air recirculation system 3 111 and close the windows. Vehicles with manual transmission and All-wheel drive: If the vehicle is towed with all four wheels on the ground then there are no technical limitations for speed and distance.
182 Vehicle care Appearance care Exterior care Locks The locks are lubricated at the factory using a high quality lock cylinder grease. Use de-icing agent only when absolutely necessary, as this has a degreasing effect and impairs lock function. After using de-icing agent, have the locks regreased by a workshop.
Vehicle care 183 Windows and windscreen wiper blades Use a soft lint-free cloth or chamois leather together with window cleaner and insect remover. When cleaning the rear window, make sure the heating element inside is not damaged. For mechanical removal of ice, use a sharp-edged ice scraper.
184 Vehicle care Rear carrier system Clean the rear carrier system with a steam-jet or high-pressure jet cleaner at least once a year. Operate the rear carrier system once in a while if not in regular use, in particular during winter.
Service and maintenance 185 Service and maintenance General information ................... 185 Recommended fluids, lubricants and parts ..............
186 Service and maintenance Recommended fluids, lubricants and parts Recommended fluids and lubricants Only use products that meet the recommended specifications. Damage resulting from the use of products not in line with these specifications will not be covered by the warranty.
Service and maintenance 187 Coolant and antifreeze Use only silicate-free long life coolant (LLC) antifreeze. The system is factory filled with coolant designed for excellent corrosion protection and frost protection down to approx.
188 Technical data Technical data Vehicle identification .................. 188 Vehicle data ............................... 190 Vehicle identification Vehicle Identification Number The Vehicle Identification Number is visible through the windscreen.
Technical data 189 Identification plate The identification plate is located on the front left door frame. Information on identification label: 1 = Manufacturer 2 = Type approval number 3 = Vehicle Ide.
190 Technical data Vehicle data Recommended fluids and lubricants European service schedule Required engine oil quality All European countries ( except Belarus, Moldova, Russia, Serbia, Turkey) Only I.
Technical data 191 International service schedule Required engine oil quality All countries outside Europe except Israel Only Belarus, Moldova, Russia, Serbia, Turkey Engine oil quality Petrol engines.
192 Technical data All countries outside Europe except Israel Only Belarus, Moldova, Russia, Serbia, Turkey Engine oil quality Petrol engines (including E85) Diesel engines Petrol engines (including E.
Technical data 193 Engine data Sales designation 2.4 3.0 V6 2.2 CDTI 2.2 CDTI Engine identifier code A 24 XF A 30 XF A 22 DM A 22 DMH Number of cylinders 4 6 4 4 Piston displacement [cm 3 ] 2384 2997 .
194 Technical data Performance All-wheel drive Engine A 24 XF A 30 XF A 22 DM A 22 DMH Maximum speed 3) [mph] Manual transmission 115 – 116 124 Automatic transmission 109 123 113 119 Front-wheel dri.
Technical data 195 Vehicle weight Kerb weight, basic model without any optional equipment Manual transmission / Automatic transmission. Engine All-wheel drive Front-wheel drive A 24 XF 1825-1885 / 184.
196 Technical data Turning circle diameter, wall to wall [m] 12.78 Turning circle diameter, kerb to kerb [m] 11.87 Maximum wading depth [mm] (at 3 mph) 450 Approach angle 20° Ramp angle 18° Departur.
Technical data 197 Capacities Engine oil Engine A 24 XF A 30 XF A 22 DM A 22 DMH including filter [l] 4.7 5.7 5.6 5.6 between MIN and MAX [l] 1.0 1.0 1.
198 Technical data Tyre pressures Up to full load Up to full load ECO Trailer towing Engine Tyres front rear front rear front rear [ kPa/bar] ([psi]) [ kPa/bar] ([psi]) [ kPa/bar] ([psi]) [ kPa/bar] ([psi]) [ kPa/bar] ([psi]) [ kPa/bar] ([psi]) All 215/70 R 16 4) , 235/60 R 17, 235/65 R 17, 235/55 R 18, 235/50 R 19 240/2.
Technical data 199 Towing hitch installation dimensions Dimension mm A 412 B 505 C 482 D 734 E 1039 F (fully laden) 363 G (at kerb weight) 481.
200 Technical data.
Customer information 201 Customer information Vehicle data recording and privacy ....................................... 201 Vehicle data recording and privacy Event data recorders The vehicle has a number of sophisticated systems that monitor and control several vehicle data.
202 Customer information In addition, the manufacturer may use the collected or received diagnostic data: ■ for the manufacturer's research needs ■ to make it available for research needs whe.
Customer information 203.
204 Index A Accessories and vehicle modifications .......................... 143 Accessory sockets ........................ 75 Active head restraints ................... 33 Adjustable air vents ................... 114 Airbag and belt tensioners ......
205 Change engine oil ....................... 86 Changing tyre and wheel size ... 170 Charging system .......................... 81 Check control................................ 96 Child locks ................................... 21 Child restraint installation locations .
206 Glovebox ..................................... 52 Graphic-Info-Display, Colour- Info-Display .............................. 91 H Halogen headlights .................... 152 Hand brake ................................. 129 Hazard warning flashers .
207 Performance .............................. 194 Performing work ........................ 144 Pollen filter ................................. 115 Power outlets ............................... 75 Power seat adjustment ................ 36 Power steering .
208 Tyre changing ............................. 174 Tyre designations ...................... 167 Tyre pressure ...................... 96, 168 Tyre pressure monitoring system ............................... 96, 168 Tyre pressures ......................
Ein wichtiger Punkt beim Kauf des Geräts Vauxhall Antara (2012) (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Vauxhall Antara (2012) noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Vauxhall Antara (2012) - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Vauxhall Antara (2012) reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Vauxhall Antara (2012) erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Vauxhall Antara (2012) besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Vauxhall Antara (2012) verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Vauxhall Antara (2012). Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Vauxhall Antara (2012) gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
