Benutzeranleitung / Produktwartung S3 MS2346 des Produzenten Acer
Zur Seite of 194
Aspire S3 MS2346 SERVICE GUIDE.
ii Revision History Refer to the table below for the up da te s ma d e to th is Aspir e S3 M S23 46 S er vice Guide . Service guide files and up dates are avail able on the ACER/CSD website. For more information, go to http://csd.acer .com.tw .The information in this guide is subject to change without notice.
iii Conventions The following conventions are used in this manual: W ARNING : ! Indicates a potential for personal injury . CAUTION : ! Indicates a potential loss of data or damage to equipment. IMPORT ANT : + Indicate s informati on that is import ant to know for the proper completion of a procedure, choice of an option, or completing a t ask.
iv General information 0 Before using this info rmation and the pr oduct it support s, read the following general information. This service guide provides you with all te chnical information relating to the basic configuration for Acer’s global product of fering.
v Aspire S3 MS2346 CHAPTER 1 Hardware Specifications Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 Operating System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 Platform .
vi BIOS Flash Utilities . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12 DOS Flash Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13 WinFlash Utility . . . . . . . . . . . . . . . . . . . .
vii Replacing the WLAN Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-50 Replacing the M-SATA Board.. . . . . . . . . . . . . . . . . . . . . . . . . . 3-51 Replacing the RTC Battery . . . . . . . . . . . . . . . . . . . . . . . . . .
viii CHAPTER 5 Jumper and Connector Locations Mainboard Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3 Clearing Password Check and BIOS Reco very . . . . . . . . . . . . . 5-5 Clearing the BIOS Pa sswords . . . . .
CHAPTER 1 Hardware S pecifications.
1-2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5 Operating System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5 Platform . . . . . . . . . . . . . . . . . . . . . . .
Hardware S pecifications and Configurations 1-3 Hardware S pecificati ons and Configurations Features 0 The following is a summary of the comp uter ’s many featu res.
1-4 Hardware Specifications and Configurations S torage Subsystem 0 Hard disk drive 0 2.5-inc h, 9. 5 mm, 5400 rp m SA T A hard disk dr ive (HDD) or 2.
Hardware S pecifications and Configurations 1-5 Power Adapter and Battery 0 19 V 3-pin AC adapter; 65 W 3 cell 3260 mAh 3S1P lithium polymer battery pack Battery life: 7 hours for models with SSD 6 hours f or models w ith HDD Charging pe rio d : 1.
1-6 Hardware Specifications and Configurations Software and T ools 0 Productivity 0 Acer ePower Management Deep Sleep Settings Adobe ® Flash ® Player 10.
Hardware S pecifications and Configurations 1-7 Web links and utilities 0 Acer Accessory S tore (Belgium, France, Germany , Italy , Netherlands, S p ain, Sweden, UK only) Acer Identity C.
1-8 Hardware Specifications and Configurations Notebook T our 0 This section provides an over view of th e features and function s of the notebook. Open Front V iew 0 Figure 1-1. Open Front V iew T able 1-1. Open Front V iew No. Icon Item Description 1 Integrate d webcam Web camera for v ideo commu nication.
Hardware S pecifications and Configurations 1-9 Rear Vi ew 0 Figure 1-2. Rear View T able 1-2. Rear View No. Icon Item Description 1 DC-in jack Connects to the AC adapter . 2 HDMI port Support s high definition digit al video connectio ns. 3 USB 2.0 port s Connects to USB devices (e.
1-10 Hardware Specifications and Configurations Left V iew 0 Figure 1-3. Lef t V iew T a ble 1-3. Lef t V i ew No. Icon Item Descripti on 1 Headphone/Mic in combo ja ck Connects to combo Head phone/Mi.
Hardware S pecifications and Configurations 1-1 1 Right V iew 0 Figure 1-4. Right View T a ble 1-4. Right Vi ew No. Icon Item Description 1 2-in-1 card reader Support s MMC, MMCplus, and SD cards.
1-12 Hardware Specifications and Configurations Base Vi ew 0 Figure 1-5. Base View T able 1-5. Base View No. Icon Item Description 1 Battery reset pinhole Insert a p aperclip into the hole and press for four seconds to reset the comput er (simulates removing and reinstalling the battery) 2 S trap Slot For optional strap accessory .
Hardware S pecifications and Configurations 1-13 T ouchpad Basics 0 Figure 1-6. T ouchpad Move finger across the multi-touchp ad (1) to move the curso r .
1-14 Hardware Specifications and Configurations Keyboard 0 The keyboard cont ains an overlay numeric ke ys, inverte d “T” cursor ke y , Windows® key , Application key , function lock keys, and hotk eys controlling various computer features. Figure 1-7.
Hardware S pecifications and Configurations 1-15 Windows Keys 0 The keyboard has two keys that perform Windows- specific functions. Figure 1-9. Windows-sp ecific Keys Num Lock Fn + F1 1 The key can be tu rned on/off via the intern al keyboard ( Fn + F1 1 ) or the external keyboard/keyp ad.
1-16 Hardware Specifications and Configurations Hotkeys 0 The computer uses hotkeys or key combinatio ns to access most computer controls. T o activate hotkeys, pr ess an d ho ld th e Fn key before pre ssin g the key in the combination.
Hardware S pecifications and Configurations 1-17 0 Fn + F8 S peaker toggle T urns the speake rs On or Off. Fn + V olume Up Increases the sound volume. Fn + V olume Down Decrease s the sound volume. Fn + Brightness Down Decreases the screen br ightness.
1-18 Hardware Specifications and Configurations D2D Recovery 0 The Acer Disk to Disk (D2D) recovery func tion allows you to us e the recovery partition to troubleshoot your computer . 1. Restart the computer . 2. During POST , press F1 to access the BIOS Setup screen.
Hardware S pecifications and Configurations 1-19 S pecification T ables 0 Computer S pecifications Item Metric Imperial Dimensions Width 32.2 cm 12.68 in Depth 21.85 cm 8.52 in Height 1.75 cm 0.68 in Weight (equi pped with 3-cell battery pack) 1.33 kg with SSD disk drive 1.
1-20 Hardware Specifications and Configurations System Board Processor Processor S pecifications Heat Sink F an T ru e V al ue T able Item Spec ificatio n Core logi c Mobile Intel ® HM77 (6MB BIOS ROM) Chipset Graphics UM A: In te gr at ed in the Intel ® Core™ Mobile Pro ce ssor USB 2.
Hardware S pecifications and Configurations 1-21 System Memory Graphics Controller System BIOS 68 5700 34 78 6200 37 85 6500 40 Throttling 50%: On= 85 °C; OF F=84 °C OS shuts down at 97 °C; Hard wa.
1-22 Hardware Specifications and Configurations Keyboard Hard Disk Drive Item Spec ification T ype Aspire AF 1S Flat keyb oard T otal nu mber of keys 84 keys Windows logo key Y es Internal and extern .
Hardware S pecifications and Configurations 1-23 Solid St ate Drive (SSD) Card Reader LCD Panel Power Requirement 5 VDC Item Specif ication V endor and models A-DA T A SSD NAND AS51 1S7-120GM A-DA T A SSD NAND AS51 1S7-240GM Product series A-DA T A SSD NAND AS51 1S7 Configuration Interface Serial A T A-6Gb/s Capacity (GB) 120 240 Performance Max.
1-24 Hardware Specifications and Configurations Supported Display Resolutions Audio Codec Audio Interface Response time T ypical Maximum 8m s 16 ms T ypical power consumption (watt) 3 W Electrical interface 1-channel L VDS Backlight White LED (WLED) Weight 310 g Physical size 306.
Hardware S pecifications and Configurations 1-25 Web cam Wireless LAN USB Interface HDMI Port Compatibility High Definiti on Audio S pecification Sampling rate 1 Hz resolution VSR (V ariable Sampling .
1-26 Hardware Specifications and Configurations System LED Indicators Battery Pack AC Adapter System Power Manageme nt Data throughput Up to 16.7 million colors Number of HDMI port 1 Location Back Item Specification Power status Solid blue: The computer is turned on.
Hardware S pecifications and Configurations 1-27 Power glob al states G3 Mechanical Off - This of f state is entered through a mechanical means; no electrical current is running through the circuitry and it can be worked on without damaging the hardware or endanger ing service personnel.
1-28 Hardware Specifications and Configurations System DMA Specification System Interrup t Specificat io n Legacy M ode Power Management DMA0 Free DMA1 Free DMA2 Free DMA3 Free DMA4 Dir ect m emory ac.
Hardware S pecifications and Configurations 1-29 System IO Address Map I/O addres s (h e x) System Function (ship ping configuration) 0000 - 001F Direct Memory Access Controller 0000- 0CF7 PCI bus 002.
1-30 Hardware Specifications and Configurations 00AC - 00AD Programmable Interr upt Controller 00B0- 00B1 Programmable Interrupt Controller 00B2- 00B3 Moth erboard resou rces 00B4- 00B5 Programmable I.
CHAPTER 2 System Utilities.
2-2 BIOS Setup Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 Navigating the BIOS Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 BIOS Menus . . . . . . . . . . . . . . . . . . . . . . . . . .
System Utilities 2-3 System Utilities BIOS Setup Utility 0 This utility is a hardware configuration program built into a computer’s BIOS (Basic Input/Output System). The utility is pre-configured and optimized so most users do not need to run it. If configuration problems occur , the setup utility may need to be run.
2-4 System Utilities BIOS Menus 0 This section describes the InsydeH2O BIOS Setup Utility menu ta bs. NOTE: NOTE : The screenshot s used in this chapter are for referen ce only . Actual values can vary depending on the compu ter model. Information 0 This tab shows a summary of the computer‘s hardware infor mation.
System Utilities 2-5 Product Name Model name of th e computer Manufacturer Name Computer manufa cturer UUID The universally unique iden tifie r tag assign ed to the c omp ut er T a ble 2-1.
2-6 System Utilities Main 0 Use this tab to set the system time a nd date, e nable or disable boot options, and enab le or disable the D2D recovery featur e.
System Utilities 2-7 Security 0 Use this tab to safe guard and protect the co mputer from unauthorized use. Figure 2-3. BIOS Security NOTE: NOTE : When prompted to enter the passwor d, three attempt s are allowed be fore system halts. Resetting the BIOS password may require the user to return the computer to its de aler .
2-8 System Utilities Setting a Password 0 Follow the succeeding instruction s to set the user or supervisor passwords. 1. Press to hig hlight a Set _______ Password p arameter and press Enter . The Set _______ Password dialog box appe ars. Figure 2-4.
System Utilities 2-9 Changing a Password 0 1. Press to hig hlight a Set _______ Password p arameter and press Enter . The Set _______ Password dialog box appe ars. Figure 2-6. Set Supervisor Password 2. T y pe the cur rent password in the Enter Current Password field and press Enter .
2-10 System Utilities Boot 0 Use this tab to set th e preferred d rive sequence in which th e Setup Utility attempt s to boot the operating system. By default, the computer searches for boot de vices in the following order: 1. Hard di sk drive 2. External USB boot able device 3.
System Utilities 2-1 1 Exit 0 Use the Exit tab to save or discard changes and close the BIOS Setup Utility . Figure 2-9. BIOS Exit T able 2-4. Exit Parameters Parameter Description Exit Saving Changes Close the BIOS Setup Utility and save the setup changes.
2-12 System Utilities BIOS Flash Utilities 0 BIOS Flash memory u pdates are required for the following conditions: New versions of system programs New features or options Restore a BIOS when it becomes corrupted. Use the Flash utility to update the system BIOS Flash ROM.
System Utilities 2-13 DOS Flash Utility 0 Perform the following to use the DOS Flash Utility : 1. Press F2 during boot to enter Setup Menu . 2. Select Boot Menu to modify boot priority order . Example: If using USB HDD to Update BIOS , move USB HDD to position 1.
2-14 System Utilities Remove HDD/BIOS Password Utilities 0 This section explains how to remove the HDD and BIOS p asswords. Removing the HDD Password 0 NOTE: NOTE : If the incorrect HDD password is entered th ree times in succession, an error is generated.
System Utilities 2-15 Removing the BIOS Passwords 0 T o clear a lost BIOS password (user or supervisor password), you need to short the clear password har dware gap (G2201) locate d on the mainboard. Refer to the “ Clearing the BIOS Passwords ” on p age 5-5 section for detailed instructions.
2-16 System Utilities Using DMI T ools 0 The DMI (Desktop Manag em e nt Inte rf ac e) T ool copies BIOS information to EEPROM (Electrically Erasable Program mable Read-Only Memory). Used in the DMI poo l for hardware management. LAN EEPROM Utility 0 LAN EEPROM Utility enables to change the MAC address.
CHAPTER 3 Machine Maintenance.
3-2 Machine Disassembly and Replacement . . . . . . . . . . . . . . . . . . 3-3 Recommended Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3 Replacement Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3 Pre-disassembly Instructions .
3-3 Replacing the Battery Pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-71 Replacing the Lower Case. . . . . . . . . . . . . . . . . .
3-4.
Machine Maintenance 3-5 Machine Maintenance Machine Disassembly and Replacement 0 This chapter contains step -b y-ste p pro ce dures on how to disassemble the notebook computer for maintena nc e and troublesh ooting. Cable paths and p ositioning may not represent the actual model.
3-6 Machine Maintenance Pre-disassembly Instructions 0 Before proc eeding with the disassem bly procedur e, make sur e that you do the followin g: 1. T urn of f the power to the system and all peripherals. 2. Unplug the AC ad ap te r and all po we r an d sig na l cab les from the syste m .
Machine Maintenance 3-7 Disassembly Process 0 The flowchart provided in this disassembly section illu strate the entire di sassembly sequence. Observe the order of the sequ ence to avoid da mage to an y of the hardwar e componen t s.
3-8 Machine Maintenance Mainboard Disassembly M2 x L3 1 86.00E14.523 RTC Battery Disassembly - - - WLAN Board Disassembly - - - Keyboard Disassembly M1.4 x L1.2 29 86.EA322.2R0 Middle Cover Disassembly M2 x L3 4 86.00E14.523 LCD Module Disassembly M2 x L4.
Machine Maintenance 3-9 Removing the Lower Case 0 1. Remove t he twelve screw s securing the lower case. Figure 3-3. Lower Case Screws 2. Gently lift the lower case and lay it down beside the main unit. Figure 3-4. Lower Case T a ble 3-3. Screws Ste p Screw Quantity Screw T ype Lower Case Disassembly M2 x L4.
3-10 Machine Maintenance Removing the Battery Pack 0 1. Perform the “ Removing the Lower Case ” procedure described on p age 3-9 . 2. Remove the two screws securing the lef t speaker to the upper case. Figure 3-5. Left S peaker Screws 3. Lift the le ft speaker of f the upper case and temporarily place it at the side of the r ight speaker .
Machine Maintenance 3-1 1 4. Lift the DC-In & Power cable o ff the battery pack. Figure 3-7. DC-In & Power Cable 5. Remove the two screws securing the ba ttery pack to th e upper case. Figure 3-8. Battery Pack Screws T a ble 3-8. Screws Ste p Screw Quantity Screw T ype Battery Pack Disas sembly M2 x L4.
3-12 Machine Maintenance 6. Lift the battery pack of f its socket in the upper case then slide it a few millimeters aw ay from the mainboard ( 1 ). Disconnect the battery cable fro m the WLAN bo ar d ( 2 ). Figure 3-9. Battery Cable 7. Detach the batter y pack from the upper case.
Machine Maintenance 3-13 Removing the Left and Right S peakers 0 1. Perform the “ Removing the Lower Case ” procedure described on p age 3-9 . 2. Perform the “ Rem oving the Battery Pack ” procedur e described on p age 3-10 . 3. Remove the two screws securing the r ight speakers to the upp er case ( 1 ).
3-14 Machine Maintenance 6. Disconnect the speaker ’s cable from the mainboard. Figure 3-13. Speaker Cable.
Machine Maintenance 3-15 Removing the WLAN Module 0 1. Perform the “ Removing the Lower Case ” procedure described on p age 3-9 . 2. Perform the “ Rem oving the Battery Pack ” procedur e described on p age 3-10 . 3. Unplug the two an tenna cables fr om the WLAN mod ule.
3-16 Machine Maintenance 5. Remove the screw secu ring the WLAN module to th e WLAN/M-SA T A board. Figure 3-16. WLAN Module Screw 6. Detach the WL AN module from the slot. Figure 3-17. WLAN Module NOTE: NOTE : A circuit board that is > 10cm 2 has been highlight ed with a ye llow rectangle in Figure 3-17 .
Machine Maintenance 3-17 Removing the DC-In Module (WLAN Board) 0 NOTE: NOTE : For models that have M-SA T A board installed, please pr oceed to page 3- 18 , “ Removing the DC-In M odule (M-SA T A Boar d) ” 1. Perform the “ Removing the Lower Case ” procedure described on p age 3-9 .
3-18 Machine Maintenance Removing the DC-In Module (M-SA T A Board) 0 1. Perform the “ Removing the Lower Case ” procedure described on p age 3-9 .
Machine Maintenance 3-19 Removing the HDD Module 0 NOTE: NOTE : For models that have SSD disk drive installed, please proceed to page 3-22 , “ R emoving the SSD Module ”. 1. Perform the “ Removing the Lower Case ” procedure described on p age 3-9 .
3-20 Machine Maintenance 5. Remove the screw securing the HD D module to the upper case. Figure 3-24. HDD Module Screw 6. Detach th e HDD module from the upper case .
Machine Maintenance 3-21 7. Detach the ca ble from the HDD module. Figure 3-26. HDD Cable 8. Remove th e four screw s securing the HDD module to the bracket ( 1 ) then detach the HDD module from the bracke t ( 2 ). Figure 3-27. HDD Bracket Screws T a ble 3-27.
3-22 Machine Maintenance Removing the SSD Module 0 1. Perform the “ Removing the Lower Case ” procedure described on p age 3-9 . 2. Perform the “ Rem oving the Battery Pack ” procedur e described on p age 3-10 . 3. Release the SSD cable from the adh esive ta pe securing i t.
Machine Maintenance 3-23 5. Remove t he screw s ecuring the SSD module to the upper case. Figure 3-30. SSD Module Screw 6. Detach the SSD mod ule from the upper case .
3-24 Machine Maintenance 7. Detach the ca ble from the SSD module. Figure 3-32. SSD Cable 8. Remove the four screws secur ing the SSD module to th e bracket ( 1 ) then det ach the SSD module from the bracke t ( 2 ). Figure 3-33. SSD Bracket Screws T a ble 3-33.
Machine Maintenance 3-25 Removing the Card Reader Board 0 1. Perform the “ Removing the Lower Case ” procedure described on p age 3-9 . 2. Perform the “ Rem oving the Battery Pack ” procedur e described on p age 3-10 . 3. Disconnect the card reader cab le from the mainboard an d the card reader boar d.
3-26 Machine Maintenance 5. Detach the ca rd reader board from the upper case. Figure 3-36. Card Reader Board NOTE: NOTE : A circuit board that is > 10cm 2 has been highlight ed with a ye llow rectangle in Figure 3-36 . Follow the local regulations fo r disposing this type of circuit board.
Machine Maintenance 3-27 Removing the Mainboard 0 1. Perform the “ Removing the Lower Case ” procedure described on p age 3-9 . 2. Perform the “ Rem oving the Battery Pack ” procedur e described on p age 3-10 . 3. Release the connector latch ( 1 ) from the mainboard, then disconnect the touchpad cable ( 2 ).
3-28 Machine Maintenance 5. Release the connector latch ( 1 ) from the mainboar d, then disconnect the p ower button cable ( 2 ). Figure 3-39. Power Button Cable 6. Release the latch ( 1 ) from the mainboard then disconnect the keyboard cabl e ( 2 ). Figure 3-40.
Machine Maintenance 3-29 7. Release the LCD cable from th e adhesive t ape secu rin g it. Figure 3-41. LCD Cable Adhesive T ape 8. Disconnect the LCD cable from the main board.
3-30 Machine Maintenance 9. Remove the screw securin g the mainboard to the upp er case. Figure 3-43. Mainboard Screw 10. Detach the main board from the upper ca se. Figure 3-44. Mainboard NOTE: NOTE : A circuit board that is > 10cm 2 has been highlight ed with a ye llow rectangle in Figure 3-44 .
Machine Maintenance 3-31 Removing the Thermal Module 0 1. Perform the “ Removing the Lower Case ” procedure described on p age 3-9 . 2. Perform the “ Rem oving the Battery Pack ” procedur e described on p age 3-10 . 3. Disconnect the thermal module fan cabl e from the mainboard.
3-32 Machine Maintenance 5. Detach the th ermal module from the mainbo ard. Figure 3-47. Thermal Module.
Machine Maintenance 3-33 Removing the R TC Battery 0 1. Perform the “ Removing the Lower Case ” procedure described on p age 3-9 . 2. Perform the “ Rem oving the Battery Pack ” procedur e described on p age 3-10 . 3. Perform the “ Rem oving the Mainboard ” pro cedure descri bed on pag e 3-27 .
3-34 Machine Maintenance Removing the WLAN Board 0 NOTE: NOTE : For models that have M-SA T A board installed, please pr oceed to page 3- 35 , “ Removing the M-SA T A Board ”. 1. Perform the “ Removing the Lower Case ” procedure described on p age 3-9 .
Machine Maintenance 3-35 Removing the M-SA T A Board 0 1. Perform the “ Removing the Lower Case ” procedure described on p age 3-9 . 2. Perform the “ Rem oving the Battery Pack ” procedur e described on p age 3-10 . 3. Perform the “ Removing the WLAN Module ” procedure described on page 3-15 .
3-36 Machine Maintenance Removing the Keyboard 0 NOTE: NOTE : The keyboard is easily warped o r damaged during th e removal process. T ake care not to use excessive force when removing. 1. Perform the “ Removing the Lower Case ” procedure described on p age 3-9 .
Machine Maintenance 3-37 12. Remove the twenty nine scr ews securing the keyboard to the uppe r case. Figure 3-56. Keyboard Screws 13. Deta ch the keyboard fro m the upper ca se. Figure 3-57. Keyboard T a ble 3-56. Screws Ste p Screw Quantity Screw T ype Keyboard Disassembly M1.
3-38 Machine Maintenance Removing the Power Button Board 0 1. Perform the “ Removing the Lower Case ” procedure described on p age 3-9 . 2. Perform the “ Rem oving the Battery Pack ” procedur e described on p age 3-10 . 3. Release the latch ( 1 ) from the mainboard then disconnect the power button cable ( 2 ).
Machine Maintenance 3-39 Removing the Middle Cover Assembly 0 1. Perform the “ Removing the Lower Case ” procedure described on p age 3-9 . 2. Perform the “ Rem oving the Battery Pack ” procedur e described on p age 3-10 . 3. Perform the “ Removing the Left and Right S pea ke rs ” procedure described on p age 3-13 .
3-40 Machine Maintenance 12. T ilt the upper case un til it is approxima tely at a 100° an gle with the LCD assembly . Figure 3-61. Upper Case Assembly 13.
Machine Maintenance 3-41 Removing the LCD Module 0 1. Perform the “ Removing the Lower Case ” procedure described on p age 3-9 . 2. Perform the “ Rem oving the Battery Pack ” procedur e described on p age 3-10 . 3. Perform the “ Removing the Left and Right S pea ke rs ” procedure described on p age 3-13 .
3-42 Machine Maintenance 13. Remove the four screws secur ing the upper case to the LCD hinges. Figure 3-64. Upper Case Screws – LCD Hinges 14. Gently detach the LCD cable from the upper case ( 1 ) and lift the upper case away fr om the LCD module ( 2 ).
Machine Maintenance 3-43 Reassembly Process 0 Replacing the LCD Module 0 1. T ilt the LCD hinge appr oximately at a 45° an gle then inse rt the upper case and align the screw posts of th e upper case with the screw holes in the LCD hinge s. Figure 3-66.
3-44 Machine Maintenance 3. Secure the upper case to the LCD hinges using four screws. Figure 3-68. Upper Case - LCD Hinge Screws T a ble 3-68. Screws Ste p Screw Quantity Screw T ype Upper Case Re assembly M2 x L4.
Machine Maintenance 3-45 Replacing the Middle Cover Assembly 0 1. T ilt the upper case un til it is approxima tely at a 100° an gle with the LC D assembly Figure 3-69. Upper Case Assembly 2. Insert the middle c over assembly in its slot. Figure 3-70.
3-46 Machine Maintenance 3. Pull the upper case downward until it sits parallel with the LCD assembly . Figure 3-71. Upper Case Assembly 4. Secure the middle cover assembly to the up per case using four screws. Figure 3-72. Middle Cover Assembly Screws T a ble 3-72.
Machine Maintenance 3-47 Replacing the Power Button Board 0 1. Insert the power button board in its slot in the middle cover ( 1 ), then secure it using adhesive t apes ( 2 ). Figure 3-73. Power Button Board 2. Connect the power button cable to th e mainboard ( 1 ), the n press the connector latch ( 2 ) until it locks into place.
3-48 Machine Maintenance Replacing the Keyboard 0 1. Place the keyboard in its slot in the upper case. Figure 3-75. Keyboard 2. Secure the keyb oard to the upper case using twenty nine screws. Figure 3-76. Keyboard Screws T a ble 3-76. Screws Ste p Screw Quantity Screw T ype Keyboard Reasse mbly M1.
Machine Maintenance 3-49 3. Secure the keyboard to the upper case using adhesive t ape. Figure 3-77. Keyboard 4. Fix the LCD cable to the upper case. Figure 3-78. LCD Cable IMPORT ANT : + Make sure that the LC D cable is installed as highlighted in Figure 3-78 to avoid damaging the LCD cable.
3-50 Machine Maintenance Replacing the WLAN Board 0 NOTE: NOTE : For models that have M- SA T A board inst alled, please proceed to p age 3-51 , “ Repla cing the M-SA T A Board. ”. 1. Place the WLAN board in it s slot in the upper case . Figure 3-79.
Machine Maintenance 3-51 Replacing the M-SA T A Board. 0 1. Place the M- SA T A boar d in its slot in the upper case . Figure 3-81. M-SA T A Board 2. Connect the WLAN & mini 1 cables ( 1 ) to the M-SA T A board, then press the connector latch ( 2 ) until it locks into place.
3-52 Machine Maintenance Replacing the R TC Battery 0 1. Secure the RTC battery to the bo ttom of the mainboard using self adhe sive tape. Figure 3-83.
Machine Maintenance 3-53 Replacing the Thermal Module 0 1. Place the th er ma l modu le in its slot in the mainbo ar d . Figure 3-85. Thermal Module 2. Secure th e thermal m odule using t he spring-lo aded captive screws. Fo llow the screw sequence indicated on Figure 3-86 .
3-54 Machine Maintenance 3. Connect the thermal module fan cable to the mainboard. Figure 3-87. Fan Cable.
Machine Maintenance 3-55 Replacing the Mainboard 0 1. Place the ma in bo ard in its slot in the upper case . Figure 3-88. Mainboard 2. Secure the mainboard to the up per case using one scr ew .
3-56 Machine Maintenance 3. Connect the LCD cable to the mainboa rd. Figure 3-90. LCD Cable 4. Secure the LCD cable to the mainboard using adhesive t ape.
Machine Maintenance 3-57 5. Connect the keyboa rd cable to th e mainboard ( 1 ) and then push the connector latch ( 2 ) until it locks into place. Figure 3-92. Keyboard Cable 6. Connect the WLAN & mini 1 cables ( 1 ) to the mainboard, then pre ss the connector la tch ( 2 ) until it locks into place.
3-58 Machine Maintenance 7. Connect the touchp ad cable to the mainbo ard ( 1 ) and then press the co nnector latch ( 2 ) until it locks into place. Figure 3-94.
Machine Maintenance 3-59 Replacing the Card Reader Board 0 1. Place the card reader board in its slo t in the upper case. Figure 3-95. Card Reader Board 2. Secure the card reader boar d to the upper case us ing two screws. Figure 3-96. Card Reader Board Screws T a ble 3-96.
3-60 Machine Maintenance 3. Connect the card reader cable to the mainboard an d the card reader board . Figure 3-97. Card Reader Cable.
Machine Maintenance 3-61 Replacing the HDD Module 0 NOTE: NOTE : For models that have SSD disk drive installed , please proceed to page 3-64 , “ Replacing the SSD Module ” 1. Place the HDD module in the bracket ( 1 ) and then secure the HDD bracke t using four screws ( 2 ).
3-62 Machine Maintenance 3. Place the HDD module in its slot in the upper case. Figure 3-100. HDD Module 4. Secure the HDD module to the upper case using one screw .
Machine Maintenance 3-63 5. Connect the HDD cable to the mainboar d. Figure 3-102. HDD Cable 6. Secure the HDD cable to the upper case using ad hesive tape.
3-64 Machine Maintenance Replacing the SSD Module 0 1. Place th e SSD module in the bracke t ( 1 ) and then secure the SSD bracket using four screws ( 2 ). Figure 3-104. SSD Bracket Screws 2. Connect the cable to the SSD module. Figure 3-105. HDD Cable T a ble 3-104.
Machine Maintenance 3-65 3. Place th e SSD module in its slot in the upp er case. Figure 3-106. SSD Module 4. Secure the SSD module to the upper ca se using one screw .
3-66 Machine Maintenance 5. Connect the SSD cable to the mainboard. Figure 3-108. SSD Cable 6. Secure the SSD cable to the upper case using adhesive t ape.
Machine Maintenance 3-67 Replacing the DC-In Module (WLAN Board) 0 1. Place the DC-In socket in it s slot in the upper case. Figure 3-1 10. DC-In 2. Connect the DC-In cable to the WLAN bo ard ( 1 ) then secure the DC-In ca ble to th e upper case using self adhesive t ape ( 2 ).
3-68 Machine Maintenance Replacing the DC-In Module (M-SA T A Board) 0 1. Place the DC-In socket in it s slot in the upper case. Figure 3-1 12. DC-In 2. Connect the DC-In cable to the M- SA T A board and the mainboard ( 1 ) then secure the DC-In cable to the uppe r case using s elf adhesive tape ( 2 ).
Machine Maintenance 3-69 Replacing the WLAN Module 0 1. Insert the WLA N module in its slot in the WLAN board. Figure 3-1 14. WLAN Module 2. Secure the WLAN module to the upper case using one screw .
3-70 Machine Maintenance 3. Secure the antenna cables to the upper case using adhesive ta pes. Figure 3-1 16. Antenna Cables Adhesive T apes 4. Connect the two antenna cables to the WLAN module. Figure 3-1 17. WLAN Module Antennas IMPORT ANT : + Connect the black cable to the main connecto r and the white cable to the auxiliary connector .
Machine Maintenance 3-71 Replacing the Right S peakers 0 1. Connect the speaker’s cable to the mainboar d. Figure 3-1 18. Speaker Cable 2. Place the rig ht speake r in its slot in the uppe r ca se .
3-72 Machine Maintenance 3. Secure the speaker cable to the upper ca se using adhesive t apes ( 1 ), then secure the right speaker to the up per case using two screws ( 2 ). Figure 3-120. Right Speaker Screws and Adhesive T ape T a ble 3-120. Screws Ste p Screw Quantity Screw T ype Right S peaker Module Reas sem b ly M1.
Machine Maintenance 3-73 Replacing the Battery Pack 0 1. Slide the b attery pack unde rneath the mini 1 and W LAN/M-SA T A cables as shown. Figure 3-121. Battery Pack 2. Connect the battery cable to the WL AN board ( 1 ), then pu sh the battery p ack forward until its four socket holes fits into th e screw posts in the uppe r case ( 2 ).
3-74 Machine Maintenance 3. Secure the battery pack to the upper case using tw o screws. Figure 3-123. Battery Pack Screws 4. Secure the DC-In & Power cable to the battery pack surface using self adhesive tapes. Figure 3-124. DC-In & Power Cable Self Adhesive T apes T a ble 3-123.
Machine Maintenance 3-75 5. Place the left speaker in its slot in the upper case. Figure 3-125. Left S peaker 6. Secure th e left sp eaker to the upper case using two screws. Figure 3-126. Left S peaker Screws T a ble 3-126. Screws Ste p Screw Quantity Screw T ype Left S peaker Module Re assembly M1.
3-76 Machine Maintenance Replacing the Lower Case 0 1. Place the lower case into th e upper case, making sure the I/O ports of the mainboard are extruding from their port hole s. Figure 3-127. Lower Case 2. Secure the lower case using twelve screws. Figure 3-128.
CHAPTER 4 T roubleshooting.
4-2 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3 General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3 Power On Issues . . . . . . . . . . . . . . . . . . .
T roubleshooting 4-3 T roubleshooting Introduction 0 This chapter contains inform at ion abo u t tro ubl e sho o tin g com m o n pr ob lems as so cia ted wi th the computer . General Information 0 The following procedu res are a guide for tr oubl eshooting compute r problems.
4-4 T roubleshooting Power On Issues 0 If the system does not power on, perform the following, one at a time, to correct the problem. Do not replace a non-d efective FRU. Figure 4-1. Power On Issue Computer Shuts Down Intermittently 0 If the system powers off at intervals, perform the following.
T roubleshooting 4-5 No Display Issues 0 If the Display does not work, perform the fo llowing, one at a time. Do not replace a non-defective FRU: Figure 4-2. No Display Issue No POST or Video 0 If the POST or video doe s not appear , perform the followi ng one at a time.
4-6 T roubleshooting 3. Drain stored power by removing the power cable and the battery p ack. Hold the power button for 10 se conds. 4. Connect the power cable and r eboot the computer . 5. Connect an external monitor to the computer an d switch between the internal display and the external disp la y by pr ess ing Fn + F5 .
T roubleshooting 4-7 8. Run th e Windows Me mory Diagno stic from th e operating s ystem DVD a nd follow the on-screen pr om p ts. 9. If the issue is still not resolved, refer to the Online Support Informat ion on page 9-3 LCD Failure 0 If the LCD fa ils, perform the following , one at a time.
4-8 T roubleshooting Keyboard Failure 0 If the Keyboard fails, p erform the following, one at a time. Do not replace a non-defective FRU: Figure 4-4. Keyboard Failure.
T roubleshooting 4-9 T ouchpad Failure 0 If the T ouchpad fails, perform the following, one at a time. Do not repla ce a non-defective FRU: Figure 4-5.
4-10 T roubleshooting Internal S peaker Failure 0 If internal S peakers fail, perfor m the follow ing, one at a time. Do not repl ac e a no n- de fe ct ive FRU: Figure 4-6. Internal Speaker Failure Sound Problems 0 Perform the following , one at a time.
T roubleshooting 4-1 1 Drag the slider to 50. Confirm that the volume is not muted. Click Mixer to verify th at other aud io applicat ions are set to 50 and n ot muted. 6. Navigate to S tart Control Panel Hardware and Sound Sound.
4-12 T roubleshooting Microphone Failure 0 If internal or external Microp hones fail, perform the follo wing, one at a time. Figure 4-7. Microphone Failure 1. Check that the microphone is enabled. Navigate to S tart Control Panel Hard ware and Sound Sound a nd select the Recording tab.
T roubleshooting 4-13 USB Failure 0 If the USB fails, perform the following, one at a ti me. Do not replace a non-defective FRU: Figure 4-8. USB Failure.
4-14 T roubleshooting WLAN Failure 0 If the WLAN fails, perform the following, one at a time. Do not replace a non-defective FRU: Figure 4-9. WLAN Failure.
T roubleshooting 4-15 Card Reader Failure 0 If the Card Reader fails, perform the following , one at a time. Do not replace a non-defective FRU: Figure 4-10.
4-16 T roubleshooting Thermal Unit Failure 0 If the Thermal Unit fails , perform the following, one at a ti me. Do not replace a non-defe ctive FRU: Figure 4-1 1.
T roubleshooting 4-17 Other Functions Failure 0 1. Check if drives are functioning correctly . 2. Check if external mo dules are fun ctioning cor rectly .
4-18 T roubleshooting Intermittent Problems 0 Intermittent system hang problems can be caused by a variety of reason s that have nothing to do with a hardware de f ect, such as: cosmic radiation, el ectrostatic dischar ge, or sof tware errors. FRU replacemen t should be considered only wh en a recurring problem exist s.
T roubleshooting 4-19 Error Codes 0 T able 4-2. Error Codes Error Codes Error Messages 006 Equipment C onfiguration Error Causes: 1. CPU BIOS Update Code Mismatch 2.
4-20 T roubleshooting BIOS Beep Codes 0 T a ble 4-3. BIOS Beep Codes Code Beeps POST Routine Description 02h V erify Real Mode 03h Disable Non-Maskable Interru pt (NMI) 04h Get CPU type 06h Initialize.
T roubleshooting 4-21 2Fh Enable cache before system BIOS shadow 30h 1-4-1-1 RAM failure on data bit s xxxx of high byte of memory bus 32h T est CPU bus-clock fre qu ency 33h Initialize Phoenix Disp a.
4-22 T roubleshooting 69h Setup System Management Mode ( SMM) area 6Ah D isplay extern al L2 cache size 6Bh Load custom defaults (optional) 6Ch Display sh ad ow -area messag e 6Eh Display possible hig.
T roubleshooting 4-23 99h Check for SMAR T drive (option al) 9Ah Shadow option ROMs 9Ch Set up Power Mana gement 9Dh Initialize security engine (optional) 9Eh Enable hardware inte rrupt s 9Fh Determin.
4-24 T roubleshooting C8h Force check (optional) C9h Extended ch ecksum (optiona l) D2h Unknown inte rrupt E0h Initialize the chipset E1h Initialize the bridge E2h Initialize the CPU E3h Initialize th.
T roubleshooting 4-25 POST Codes 0 There are two types of POST codes: Prog ress Codes and Error Codes. Progress Codes are designed to show the execution poin t while b ooting or executing services. Error Codes a re designed to halt on exceptional (f atal) er ror conditions.
4-26 T roubleshooting POSTCODE_ CC_HII _FORM S_BROWSER (0x3a) POSTCODE_ CC_BOOT_MENU ( 0x3b) POSTCODE_C C_USER_M ANAGER (0x3c) POSTCODE_ CC_TIMER (0 x3d) POSTCODE_CC_PCI_BUS (0x3e) POSTCODE_ CC_I SA_B.
T roubleshooting 4-27 0xa0-0xaf These values are reserved for Secure Core T iano™ platfo rm component s. POSTCODE_C C_PLA TFORM_ST AGE0 (0xa0) - Early PEI Plat form Initialization. POSTCODE_ CC_PLA TFORM_ST AGE 1 (0xa1) -PEI Platform Initialization.
4-28 T roubleshooting 0xe0-0xf f These are not component s, but rather repr esent Architectura l Progress Codes or Error Codes detailing milest ones in the system boot progress. The corresponding Progress Code value is always set to zero. POSTCODE_ PC_SEC_E NTRY (0xe0) - Re set vect or .
T roubleshooting 4-29 Progress Codes 0 This section describes the progre ss code values. T able 4-5. Progress Codes Range Description 0x00-0x1f S ta ndard progress Codes. All other values are rese rved. POSTCODE_PC_COMP_PEI_BEGIN (0x01) - The component was loaded and the PEI entr y point called.
4-30 T roubleshooting.
CHAPTER 5 Jumper and Connector Locations.
5-2 Mainboard Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3 Clearing Password Check and BIOS Reco very . . . . . . . . . . . . . 5-5 Clearing the BIOS Pa sswords . . . . . . . . . . . . . . . . . . . . . . . . . .
Jumper and Connector Locati ons 5-3 Jumper and Connector Locations Mainboard Layout 0 Figure 5-1. Mainboard T op T a ble 5-1. Mainboard T op No. Code Component No.
5-4 Jumper and Connector Locations Figure 5-2. Mainboard Bottom T a ble 5-2. Mainboard Bottom No. Code Component 1 G2201 Clear password hardwar e gap 2 RAM2/4/6/8 Onboard memory 3 DMIC1 Mic-in.
Jumper and Connector Locati ons 5-5 Clearing Password Check and BIOS Recovery 0 This section provides pro cedures for: Clearing the BIOS passwords Performing a BIOS recovery Clearing the.
5-6 Jumper and Connector Locations Performing a BIOS Recovery 0 Boot Block 0 An interruption during a BIOS flash procedure (e.g. a po wer o utage) can corrupt the BIOS code, which will cause the system to go into an unbootable st ate.
Jumper and Connector Locati ons 5-7 Performing a BIOS recovery 0 NOTE: NOTE : Make sure the battery pack is inst alled to the system and that the computer is connected to a UPS unit d uring the BIOS recover y process. The function hotkey sequence Fn + Esc is used to enable the BIOS recovery process when system is powered On during BIOS POST .
5-8 Jumper and Connector Locations.
CHAPTER 6 FRU List.
6-2 Aspire S3 MS2346 Exploded Diagrams. . . . . . . . . . . . . . . . . . . . 6-4 Main Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4 FRU List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FRU (Field Repla ceable Unit) List 6-3 FRU (Field Replaceable Unit) List This chapter provides users with a FRU (Fie ld Replaceable Unit) listing in global configurations for the Asp ire S3 MS2346. Refer to this chapter whenever or dering for parts to repair or for RMA ( Return Mer chandise Aut horization).
6-4 FRU (Field Replaceable Un it) List Aspire S3 MS2346 Exploded Diagrams 0 Main Assembly 0 Figure 6-1. Main Assembly Exploded Diagram T able 6-1. Main Assembly Exploded Diagram No. Description Part Number 1 Upper Case Asse mbly 60.4QP04.001 2 Lower Case Assembly 60 .
FRU (Field Repla ceable Unit) List 6-5 5 Middle Assembly 60.4QP06.001 6 DC In 50.4QP01.001 7 Power C able 50.4QP04. 001 8 Power Board 55.XXXXX.001 9 Keyboard 10 S peaker 23.40A1V .00 1 1 1 T ouchpad 56.1700 8.031 12 Thermal module 13 Motherboard 55.XXXXX.
6-6 FRU (Field Replaceable Un it) List FRU List 0 Category Description Acer Part No. ADAPTER ADP 65W 19V L V5 ADP-65VH BA LOW PROFILE AP .06501.033 ADP LITEON 65W 19V P A-1650-6 9AW L V 5 L AP .06503.029 BA TTER Y BTY P ACK LI+ SANYO 3C 3.26AH SANYO PO L YM BT .
FRU (Field Repla ceable Unit) List 6-7 CABLES ARGENTINA 1M 27.RSF01.012 AUSTRALIA BK 1M HA VE LABEL 27.RSF01 .016 BRAZIL BK 1M 27.RSF01.0 13 CHINA BK 1M 27.RSF01.007 DENMARK BK 1M 27.RSF01.004 EU BK 1M 27.R SF01.002 ISRAEL BK 1M 27.RSF01.01 1 IT AL Y BK 1M 27.
6-8 FRU (Field Replaceable Un it) List C.A. POWER WIRE SM30HS HL 50.RSE01.002 C.A. TP FFC SM30HS HB 50.RSF01.003 C.A. WLAN FFC SM30 HS JH 50.RSF01.004 C.A.WLAN FPC SM30HS CAREER 50.RSF01.0 05 CASE/COVER/BRACKET ASSEMBL Y 60 ASSY TP BAR L/T SM30HS RESERVE 60 HDD BKT BACK ASSSY SM30HS 33.
FRU (Field Repla ceable Unit) List 6-9 HDD/HARD DISK DRIVE HDD 320GB HTS543232A7A384 0J28213 KH.32007.017 HDD 500GB HTS545050A7E380 0J23335 5.4K KH.50007.023 HDD N320GB5.4KS_4K+FO0020S 2(20G) HDD N320GB5.4KS+FO0020S2(2 0G) HDD N500GB5.4KS_4K+FO0020S 2(20G) HDD N500GB5.
6-10 FRU (Field Replaceable Un it) List KEYBOARD KB 9Z.N7WPW .20F FRENCH NK.I1017.00B KB 9Z.N7WPW .20G GERMAN NK.I1017.00C KB 9Z.N7WPW .20H HEBREW NK.I1017.00W KB 9Z.N7WPW .20K KOREAN NK.I1017.00H KB 9Z.N7WPW .20L GREEK NK.I1017.00D KB 9Z.N7WPW .20N NORWEGIAN NK.
FRU (Field Repla ceable Unit) List 6-1 1 KEYBOARD KB V128230BK1 BE BELGIUN NK.I101S.004 KB V128230BK1 BG BULGARIA NK.I101S.006 KB V128230BK1 BR BRAZILIAN PORTUGUESE NK.I101S.005 KB V128230BK1 CS CZ/SK NK.I101S.007 KB V128230BK1 DM DANISH NK.I101S.009 KB V128230BK1 EF CANADA FRENCH NK.
6-12 FRU (Field Replaceable Un it) List KEYBOARD KB V128230BS1 KR KOREAN NK.I101S.00H KB V128230BS1 RU RUSSIAN NK.I101S.00M KB V128230BS1 TI THAILAND NK.I101S.00S KB V128230BS1 UI US-INTERNA TION NK.I101S.00V LCD "LCD 13.3""WXGA AU B133XTF01.
FRU (Field Repla ceable Unit) List 6-13 SCREWS SCREW M1.4*1(OD3.8) 86.9AR51.1R2 SCREW M3X4 86.9A524.4R0 SCREW IMS M1.4*3 BZN 86.9A33N.3R0 SCREW IMS M2*2 #1 BZN 86.EA322.2R0 SCREW IMS M2*4.5 (H0.8) #1 NI 86.9A552.4 R5 SCREW M2XL3 HEAD T=0. 3 BZN 86.00E14 .
6-14 FRU (Field Replaceable Un it) List.
CHAPTER 7 T est Comp atible Component s.
7-2 Microsoft Windows 7 Environment Test . . . . . . . . . . . . . . . . . . 7-3.
T est Compatible Co mponents 7-3 T est Comp atible Component s This computer ’s compatibility is tested and verified by Acer’s in ternal testing department. All of its system functions are tested under Windows ® 7 environment. Refer to the fo llowing lists for compone nts, adapter cards, and peripher als which have passed these tests.
7-4 T est Compatible Components CPU 10001067 INTEL Ci32367MB CPU Intel Core i3 2367M BGA 1.4G 17W KC.23601.7MB 10001067 INTEL Ci33217UB CPU Intel Core i3 3217U BGA 1.8G 1600 17W Ivy Bridge KC.32101.3UM 10001067 INTEL Ci52467MB CPU Intel Core i5 2467M BGA 1.
T est Compatible Co mponents 7-5 60002036 SEAGA TE N500GB5.4 KS_ 4K HDD SEAGA TE 2.5" 5400rpm 500GB 9WS142-188 ST500L T012, Y arra 500G/P , 7mmzh SA T A 8MB LF+HF F/W:0001SDM1 KH.50001.030 60001994 WD N500GB5.4KS_ 4K HDD WD 2.5" 5400rpm 500GB WD5000LPVT -22G33T0, MN500S, 500G/P , 7mmzh HDD SA T A 8MB LF+HF F/W: 01.
7-6 T est Compatible Components 10000981 MISC AF1P_A10B Keyboard SUNREX AF1P_A10B AF1P Internal 10 S tandard Black NONE Sunrex Y2010 Acer Legend NK.I101S.001 10000981 MISC AF1P_A10B Keyboard ACER AF1 S_A10B AF1S Internal 10 S tandard Black NONE Y2010 Acer Legen d KB.
T est Compatible Co mponents 7-7 Wireless LAN 10001023 LITE-ON 3rd WiFi 1x1 BGN+ BT4.0 Lite-On 3rd WiFi 1x1 BGN+ BT4.0 Atheros WB225(WLAN HB195 1x1 BGN +BT4.0 A TH3012) NI.23600.098 10001018 HON HAI 3rd WiFi 1x1 BGN+ BT4.0 Wireless LAN Broadcom 4313iP A+20702 (WLAN 4313iP A 1x1 BGN+ BT4.
7-8 T est Compatible Components.
CHAPTER 8 Online Support Information.
8-2 Online Support Informa tion . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3.
8-3 Online Support Information 0 This section describes online tech nical support services available to help user s repair their Acer Systems. For distributors, dealers, ASP or TPM, please refer the technical querie s to a local Acer branch of fice. Acer Branch Of fices and Regi onal Business Units may access our website.
8-4.
Ein wichtiger Punkt beim Kauf des Geräts Acer S3 MS2346 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Acer S3 MS2346 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Acer S3 MS2346 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Acer S3 MS2346 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Acer S3 MS2346 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Acer S3 MS2346 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Acer S3 MS2346 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Acer S3 MS2346. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Acer S3 MS2346 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
