Benutzeranleitung / Produktwartung BCT-10 des Produzenten Uniden
Zur Seite of 40
Introduction Welcome Congratulations on your purchase of the BCT-10 Highway Information System & Scanning Radio! State-of-the-art engineering and advanced electronics provi de you with a preprogrammed information radio desi gned for easy operation and dependability.
Terms and Definitions Fr eq u en c y Radio signals are sent as waves through the air. These waves move up and down. A frequency is the number of times in a certain time period, usually a second, that these waves move all the way up and all the way down and back to all the way up.
Unpacking Carefully remove all items from the box. If there is any visible damage, do not operate the equipment. Notify your dealer or shipping carrier immediately. For information or instructions on any problem that you may have, call the Uniden Customer Service Center at: (800) 297-1023 Monday through Friday, 8:00 a.
Included with Your B CT-10 Scanner If any of these items are missing, please contact your place of purchase. OFF MUTE MODE ALARM L/0 HOLD STATE HIGHWAY SYSTEM The BCT-10 High way Information System Wi.
Installation The BCT-10 uses a highly sensitive antenna to receive radio signals. Its sensitivity and range depend on the method of installati on and the direction of the antenna in relation to the signal source.
Installing the Antenna B CT-10 A n t en n a 1. Pinch the sides of the antenna and attach it to the BCT -10. F l e xib le M obile A nte nna 1. Mount the antenna on the inside of the windshiel d at the f ar r ight-hand (passenger) side . Caution: Be sure the antenna does not obstruct the driver’s vision in any way.
Cau t i o n : Be sure the cable is out of the way of anyone getting in or out of the car. 3. Plug the cable ’ s BNC connector into the BCT -10. Mounting the BCT-10 V isor M ounting 1. Snap the visor clip onto the BCT -10. Note: Make sure that the bracket tabs fit securely in the slots.
2. Slide the clip o v er the front of the visor . 3. Adjust the angle of the antenna as close to straight up or down as possib le . Note: You can remove and replace the BCT-10 by sliding both the unit and the visor mount off and on the visor.
W indshie ld M ounting 1. Find a good position for the BCT-10 on your windshield. Refer to the Helpful Tips on page 5 for some guidel ines on mounting positions.
4. Snap the windshield mounting clip onto the BCT -10. 5. Slide the plastic windshield mounting clip into the the metal mounting brack et. The mounting cli p locks into the plastic portio n at three different positions. These positi ons can be used for vehicles with different vertical angles of their windshields.
6. Place the brac k et and the BCT -10 in the proper location on the windshield of y our v ehicle and press the suction cups fir mly against the windshield. If the BCT -10 does not fit flush against the windshield, tr y a diff erent position on the metal mounting brac ket.
Connecti ng the P o wer Direct Connection WARNI NG: The BCT-10 is designed to operate only with 12V DC, negative ground power systems. Operation of the unit on other voltages or polariti es will cause damage to the unit and may create a fire hazard.
3. Run the power cord from the fuse box to the BCT-10. Note: Ensure the cord does not interfere with vehicle operation or cause a tripping hazard. 4. Plug the power cord connector into the Control Unit at the jack labeled “DC 12V.” Note: Push the connector firmly into the jack.
When installing the power cord, make sure that: • The socket is clean to allow proper contact. • The power cord does not block the antenna area of the unit.
Operating Instructions Applying Power 1. T ur n the OFF/V OLUME control counter cloc kwise to power on the scanner . Adjust the v olume about 1/4 tur n. 2. Dur ing po wer-on, a self-test is perf or med. Check the front control panel f or proper operation.
Adjusting the Sque lch Think of the Squelch Control as a gate. 1. Turn the SQUELCH control fully counterclockwise. This raises the “Squelch Gate” so high that no signals can get through. 2. Turn the SQUELCH control fully clockwise until you hear a hiss.
3. Turn the SQUELCH conrol back counter clockwise just until the hiss stops. Now the “Squelch Gate” allows only strong signals through. 4. Sometimes when you open the Squelch, you may trigger the Alert feature even though no highway patrol cars are in the area.
Selecting the State 1. Select the state you are operating in b y pressing the S ke y repeatedly . If you press and hold the S ke y f or 2 seconds, the selector mov es rapidly through all the states and Canadian provin ces. 2. The state code appears on the displa y .
State Codes Code State Code State AK Alask a NM New Mexico AL Alabama NV Nevada AR Arkans as NY New York AZ Arizo na OH Ohio CA Californ ia OK Oklahoma CO Colorado OR Oregon CT Connecticut PA Pennsylv.
Selecting the Frequencies to Scan Sc an n i n g A l l Fr eq u en c i es Note: The Alert feature is not active in this mode. 1. T o scan all frequencies (e xcept W eather), press the S ke y repeatedly or press and hold the S ke y until “XX” is bli nking on the LED displa y .
Sc an n i n g Hi g h w ay Pat r o l Fr eq u en c i es 1. T o scan highwa y patrol frequencies e xclusiv ely , press the M k ey repeated ly until HP is b linkin g in the LED displa y . 2. The HP LED lights up . 3. While scanning, the BCT -10 displa ys the state code f or the state you selected.
Sc an n i n g A l l Po l i c e Fr eq u en c i es 1. T o scan highwa y patrol and local police frequencies, press the M key repeatedly until LP is bli nking on the LED displa y . 2. The LP and HP LED’ s will light up . 3. While scanning, the BCT -10 displa ys the state code f or the state you selected.
H ighwa y P a trol A la rm In most cases, when you are within three miles of a highwa y patrol unit, and a mobile e xtender is in use, your BCT -10 will set off a visual and audible ala r m. The signal strength will be displa yed, and the LED will retur n to the HP displa y .
2. The LR and SR LED’ s toggle and you hear two shor t beeps once either standard or long range mode is selected. Set t i n g t h e Hi g h w ay Pat r o l A l ar m Vo l u m e You can set the Alert Tone volume to either Low, Medium, or High. To change the Alert Tone volume: 1.
Mu t i n g t h e Hi g h w ay Pat r o l A l ar m While in the highway patrol mode you can turn off the alarm tone during the time you are listening to a frequency or disable the alarm tone permanently. To di sable the alarm tone while li stening to a frequency: 1.
To disable the alarm tone permanently: 1. Press and Hold the m key f or two seconds. 2. Y ou hear a two beeps and the MUTE LED comes on. Note: When the MUTE LED is on and not flashing, you can receive highway patrol alarms, but the alarm tone does not sound.
Mo n i t o r i n g Weat h er Fr eq u en c i es 1. T o monitor weather frequencies, press the M key repeatedly until WX is bli nking on the LED displa y . 2. While scanning, the BCT -10 will displa y WX. When the BCT -10 detects an activ e frequency , it displa ys the weather channel in the LED and stops scanning.
Deleting Frequencies Some frequencies that have been preprogrammed into your BCT-10 may not be of immediate interest to you, or a frequency may be experiencing interference. You can lock out that frequency from scanning. 1. When the scanner stops on the undesired frequency , press L one time.
Restoring Deleted Frequencies Please note that you can only restore all deleted frequencies at the same time. To restore the deleted frequencies: 1. Make sure the BCT -10 is not scanning. T o stop the unit from scanning, tur n the SQUELCH knob toward the front of the BCT -10.
Using HOLD to Stay on a Selected Frequency When scanning stops on a desired frequency, you can lock onto that frequency for as long as you like. To monitor only one frequency: 1.
If the BCT-10 stops on an undesired frequency, press the H key twice to force the unit to start scanning agai n before the end of that transmission. BE CAREFUL!! When you are in the Hold mode, there will be no Alert tones or Warning li ght, even if you are on the Alert frequency.
Troubleshooting If your BCT-10 is not performing properly, try the steps listed below. PROBL EM POS SIBLE SOLUTION Scanner is not working properly. Check power cord and in-li ne fuse. Check the Volume and Squelch settings. Signal is weak or distorted.
Optional Accessories The following optional accessories for your BCT-10 are available from your local Uniden Dealer or through the Uniden Customer Service Center by calling: (800) 297-1023, 8:00 a.
Specifications Size: 76W X 136.5D X 33H Weight: 180 g Power: 13.8 VDC Operating Temperature: -20° C (-4° F) to +60° C (+140° F) Antenna: 50 Ω impedance RF Sensitivity: (FM 12dB signal to noise ratio at 3kHz deviation) 37.02 - 46.02 MHz 0.3 µ V 138.
BCT-10 HIGHWAY INFORMAT ION SYSTEM & PREPROGRAMMED WARNING SCANNER UBZZ01258ZZ MUTE MODE ALARM L/0 HOLD STA TE HIGHWA Y SYSTEM MUTE MODE ALARM L/0 HOLD STA TE S OFF Operating Guide.
Precautions Before you use this scanner, please observe the following: WARNING! Uniden America Corporation does not represent this unit to be waterproof. To reduce the risk of fire, electrical shock, or damage to the unit, do not expose this unit to rain or moisture .
Controls and Indicators ALARM LED 5. 1. Highway Patrol LED 2. MUTE LED 6. HOLD LED 3. 2 Digit LED Display 7. Long Range LED 4. Standard Range LED 8. Local Police LED OFF MUTE MODE ALARM L/0 HOLD STA TE HIGHWA Y SYSTEM B C D E F G J H K I I I L M A A. DC Input B.
Uniden® and Bearcat® are registered trademarks of Uniden America Corporation. CONTENTS Introduction .................................................................................. 1 Welcome ........................................................
One Year Limited Warranty Importan t : Evidence of original purchase is required for warranty servi ce. WARR ANTOR : UNIDEN AMER ICA CO RPORAT ION (“Un iden”) ELEM ENTS OF WA RRAN TY: Uniden warra.
PAT. UNDER ONE OR MORE OF THE FOLLOW ING U.S. PATENT NUMBERS : 3,883,808 , 3,96 1,261 , 3,962,644 , 3,97 4,450 3,974,452 , 3,98 7,400 , 3,996,521 , 3,99 6,522 4,000,468 , 4,02 7,251 , 4,057,760 , 4,09.
Ein wichtiger Punkt beim Kauf des Geräts Uniden BCT-10 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Uniden BCT-10 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Uniden BCT-10 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Uniden BCT-10 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Uniden BCT-10 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Uniden BCT-10 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Uniden BCT-10 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Uniden BCT-10. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Uniden BCT-10 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
