Benutzeranleitung / Produktwartung 675B--Pony des Produzenten Troy-Bilt
Zur Seite of 24
Oper ator’ s Man ual Rear-tine Tiller Model 675B—P on y ® P RINTED IN U . S. A . 76 9 -0 0 58 6 A 9/22/03 FORM NO. IMPOR T ANT : READ SAFETY R ULE S AND INSTR UCTIONS CAREFULL Y WARNING: This uni.
2 TABLE OF CONTENTS FINDING MODEL NUMBER This Operator’s Manu al is an important part of your new rear-tine tiller. It will help yo u assemble, prepar e and maintain the unit for best performance.
3 T r aining 1. Carefully read this Own- er’ s Manual, the separate Engine Owner’ s Manual, and any other literature you may receive. Be thoroughly familiar with the controls and the proper use of the tiller and its engine. Know how to stop the unit and disengage the controls quickly .
4 5 . If the unit sh ould start to vibrate abnormally , stop the engine, disconnect the spark plug wire and prevent it from touching the spark plug, and check immediately for the cause.
5 Safety Decals For your safety and the safety of others, various safety and operational decals are located on your unit (see Figure 1-2 be- low). Keep the decals clean and legible at all times. Contact your local service dealer or the factory for replacements if any decals are damaged or missing.
6 WARNING: To prevent personal injury or property damage, do not start the engine until all assembly steps are complete and you have read and understand the safety and operating instructions in this Manual. Introduction Carefully follow these assembly steps to correctly prepare your tiller for use.
7 5. Move the handlebars up or down to align the threaded hole in the cross-brace with one of the four slots in the curved height adjustment bracket. Place the keyed washer (E, Figure 2-3) on the flange head height adjustment screw (F) with the raised keys (edges) of the washer facing down.
8 CAUTION: Incorrect cable adjustment could cause the wheels and tines to rotate unexpectedly. Follow adjustment procedures carefully. Failure to do so could result in personal injury or property damage. 4. Check for correct spring ⁄ cable tension as instructed in Section 5, Checking and Adjusting Forward Cl utch Belt T ension .
9 WARNING: Before operating your machine, carefully read and understand all safety, controls and operating instructions in this Manual, the separate Engine Owner’s Manual, and on the decals on the machine. Failure to follow these instructions can result in serious personal injury.
10 3. T o move the tiller in reverse, first stop all forward m otion. Lift up the handleb ars until the tines clear the ground and pull the Reverse Clutch lever out. The wheels will rotate in a reverse direction as long as the lever is held in REVERSE.
11 WARNING: Before operating your machine, carefully read and understand all safety (Section 1), controls (Section 3) and operating instructions (Section 4) in this Manual, in the separate Engine Owner’s Manual, and on the decals on the machine. Failure to follow these instructions can result in serious personal injury.
12 7. Choke or pri me the engine as instructed in the separate Engine Owner’ s Manual. 8. Check behind you to avoid contacting any obstacles when pulling the starter rope. Place one hand on the fuel tank to stabilize the unit and use the recoil starter to start the engine as instructed in the En- gine Owner’ s Manual.
13 Stopping the Tiller and Engine 1. T o stop the wheels and tines, release the Forward Clutch levers or the Reverse Clutch Control (whichever is engaged). 2. T o stop the engin e, move the Engine Throttle Lever to STOP . 3. If the engine is equipped with a fuel shut- off valve, close the valve as instructed in the Engine Owner’ s Manual.
14 Preparing Seedbeds Tilling wet soil often results in large, hard clumps of soil that can inter fere with plant- ing. If time permits, wait a day or two after heavy rains to allow the s oil to dry before tilling. T est soil by squeezing it into a ball.
15 Tilling On Slopes Read the following recomm endations before tilling on slope s: If you must garden on a moderate slope, please follow two ver y important guidelines: 1. Till only on moderate slopes, never on steep ground where footing is difficult (review safe - ty rules in Section 1 : Safety of this manual).
16 WARNING: Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Remove ignition key on electric start models. Failure to follow these instructions can result in serious personal injury or property damage.
17 A. T o Check T ransmission 1. Check the gear oil level when the trans- mission is cool. Gear oil expands in warm operating temperatures and will result in an incorrect oil level reading. 2. T o check the gear oil level (and to add oil, if necessary), refer to STEP 5: Check Gear Oil Level in T ransmission in Section 2 of this manual.
18 Carburetor / Gov ernor Adjustment WARNING: Operators shall not tamper with the engine governor settings; the governor controls the maximum safe operating speed to protect th e engine and all moving parts from damage caused by overspeed. Authorized service shall be sought if a problem exists.
19 WARNING: This is a CRT (counter-rotating tine) tiller and its tines must be mounted in the direction shown in Figure 5-7. Failure to comply could result in personal injury or property damage. 2. When installing individual tines, in stall them in the reverse order from which they were removed.
20 NOTE: While pushing inward on the forward idler ar m, be sure that the forward drive belt is mo ved off to the right side of the tiller. This creates more room to install t he clevis pin when the forward idler arm is pushed inward.
21 front of the unit (not the operator’ s posi- tion). If the belt tension is correct, reinstall the belt cover and secure it with the two nuts. • If the guide mark is aligned with the guide pin, or moves to the right side of th e guide pin, then the belt is too loose and the tension must be readjusted as described next.
22 3. Slip the forward drive belt down and over the front of the transmission pulley (C, Figure 5-16). NOTE: For additional working room, loosen the reverse belt guide (V , Figure 5-12) and twist it out of the way .
23 WARNING: Before inspecting, cleaning or servicing the machine, shut off en gine, wait for all moving parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Failure to follow these in structions can result in serious personal injury or property damage.
TR O Y -BIL T TILLER LIFETIME LIMITED W ARRANTY WHAT PRODUCT All Troy-Bilt brand ed rear tin e walk-behind tillers with gear drive transmissions. IS COVERED This warranty begins on the date of p urchase and is warranted by Troy-Bilt LLC fo r the life of the tiller, to the origin al purchaser only.
Ein wichtiger Punkt beim Kauf des Geräts Troy-Bilt 675B--Pony (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Troy-Bilt 675B--Pony noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Troy-Bilt 675B--Pony - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Troy-Bilt 675B--Pony reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Troy-Bilt 675B--Pony erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Troy-Bilt 675B--Pony besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Troy-Bilt 675B--Pony verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Troy-Bilt 675B--Pony. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Troy-Bilt 675B--Pony gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
