Benutzeranleitung / Produktwartung 645A Super Bronco des Produzenten Troy-Bilt
Zur Seite of 32
Rear -tine Tiller Models 643C — T uffy ® / Bronco CR T 643 B , 645A — Super Bronco TM Model 645A Shown Oper ator’ s Man ual PRINTED IN U.S.A. P.
2 TABLE OF CONTENTS FINDING MODEL NUMBER This Operator’s Manual is an impo rtant part of your new tiller. It will help you assemble, prepare and maintain the unit for best performance.
3 Training 1. Carefully read this Own- er’ s Manual, the separate Engine Owner’ s Manual, and any other literature you may receive. Be thoroughly familiar with the controls and the proper use o f the tiller and its en- gine. Know how to stop the unit and disen- gage the controls quickly .
4 5 . If the unit should start to vibrate abnor- mally , stop the engine, disconnect the spark plug wire and prevent it from touch- ing the spark plug, and check immediately for the cause.
5 Decals For your safety and the safety of others, vari- ous safety and operational decals are located on your unit (see Figure 1-2). Keep the decals clean and legible at all times. Contact your local service dealer or the factory for replacements if any decals are damaged or missing.
6 WARNING: To prevent personal injury or property damage, do not start the engine until all assembly steps are complete and you have read and understand the safety and operating instructions in this manual. INTRODUCTION Carefully follow these assembly steps to correctly prepare your tiller for use.
7 through the wheel shaft (L) only (not through the wheel hub). The wheel should now spin freely (freewheel) on the wheel shaft. Repeat with the other wheel.
8 4. Check for correct tens ion on the for ward drive belt by taking two measurements of the cable spring, as follows: a. With the Forward Clutch Bail (Y , Fig. 2- 6) in an open (released) position, measure the length of the cable spring (W) from the outermost coil to the outermost coil.
9 STEP 6: CHECK TRANSMISSION OIL LEVEL The transmission was filled with gear oil at the factory . However , you should check the gear oil level at this time to make certain it is correct. IMPORT ANT : Do not op erate the tiller if the gear oil level is low .
10 WARNING: Before operating your machine, carefully read and understand all safety, controls and operating instructions in this Manual, the separate Engine Owner’s Manual, and on the decals on the machine. Failure to follow these instructions can result in serious personal injury.
11 WARNING: Before starting engine, be sure that both wheels are in WHEEL DRIVE position. See Wheels Drive Pins for instructions. Engaging the Forward Clutch Bail or Reverse Clutch Control (if equipped) when the wheels are not in WHEEL DRIVE could allow the tines to rapidly propel the tiller forward or backward.
12 WARNING: Before operating your machine, carefully read and understand all safety (Section 1), controls (Section 3) and operating instructions (Section 4) in this Manual, the separate Engine Owner’s Manual, and on the decals on the machine. Failure to follow these instructions can result in serious personal injur y .
13 Stopping the Engine and Tiller 1. T o stop the wheels and tines, release the Forward Clutch Bail (all models) or the Re- verse Clutch Control (Models 643B & 645A) — whichever control is in use. 2. T o stop the engine, put the ignition switch and/or the throttle control lever in the “OFF” or “STOP” position.
14 Preparing Seedbeds Tilling wet soil often results in large, hard clumps of soil that can inter fere with plant- ing. If time permits, wait a day or two after heavy rains to allow the s oil to dry before tilling. T est soil by squeezing it into a ba ll.
15 Tilling On Slopes Read the following recommen dations before tilling on slopes: If you must garden on a moderate slope, please follow two ver y important guidelines: 1. Till only on moderate slopes, never on steep ground where footing is difficult (review safe - ty rules in Section 1 : Safety of this ma nual).
16 Terrace Gardening (continued ) • T o create a terrace, sta rt at the top of the slope and work down. Go back and forth across the first row as shown in Fig. 4-10. • Each succeeding lower terrace is started by walk ing below the terrace you’re preparing.
17 WARNING: Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Remove ignition key on electric start models. Failure to follow these instructions can result in serious personal injury or property damage.
18 4. The gear oil level is correct if the gear oil is approximately halfway up the side of the main drive shaft. 5. If the gear oil level is low , add gear oil as described next. If the gear oil level is okay , securely replace the oil fill plug. IMPORT ANT : Do not op erate the tiller if the gear oil level is low .
19 CHECKING AND ADJUSTING FORWAR D DRIVE BELT TENSION It is important to maintain correct tension on the forward drive belt. A loo se b elt wil l cause the tines and wheels to sl ow do wn — or stop completely — even though the en- gine is running at full speed.
20 FORWARD CLUTCH BAIL ADJUSTMENT If the Forward Clutch Bail does not func- tion properly , first check that the forward drive belt is adjusted properly (see Check- ing and Adjusting Forward Drive Belt T en- sion ). If this fails to correct the problem, contact T roy-Bilt LLC or your authorized dealer for service advice.
21 3. Clean around the oil dipstick or oil fill tube (whichever applies) to prevent dirt from falling into the crankcase. 4. On engines with an oil fill tube, remove the fill cap and add oil (if required) until it reaches the top of the fill tube. Reinstall the fill cap.
22 TROUBLESHOOTING PROBLEM POSSIBLE CAUSE CORRECTION Engine does not start 1. S park plug wire disconnected. 1. Reconnect wir e. 2. Engine Thr ottle Control Lever incorrectly set. 2. Put lev er in ST ART position. 3. F uel tank empty. 3. Add fuel. 4. C hoke control (if so equipped) in inco rrect position.
23 NOTES.
24 A A 11 43 45 48 42 39 6 24 49 47 39 9 14 10 44 13 5 7 7 19 9 3 20 21 2 12 18 46 7 30 26 6 17 7 8 15 37 38 35 29 34 36 27 23 25 28 24 40 4 16 22 33 32 31 1 4 41 4 Models 643C, 643B & 645A.
25 MODELS 643C, 643B & 645A REF NO. P ART NO. DESCRIPTION 1 686-04043 Tine Hood Assembly (A) 686-04041 Tine Hood Assembly (B) (C) 2 710-0395 Hex Screw, 5/16-18 x 2.25 3 710-0597 Hex Hd. Screw, 1/4-20 x 1 4 710-0599 Screw, Self-Tapping,1/4-20 x 1/2 5 710-0874 Hex Hd.
26 MODELS 643C, 643B & 645A * Use as r equired to obtain betwee n .005” and .015” allowable end-play . REF NO. P ART NO. DESCRIPTION 1 GW-9517 Snap Ring 2 GW-1714 Bearing, Tapered Roller (with race) 3 GW-50043 Support Washer, Rear 4 711-04110 Drive Shaft 5 GW-1224-1* Shim, Rear Bearing Cap, .
27 MODELS 643C, 643B & 645A * Use as required to obt ain between .005” and .030” allowable end-play . REF NO. PA R T N O . D E S C R I P T I O N 2 1909950 Retainer, Snap Ring 3 GW-1166-1* Shim, 0.062" thick GW-1166-2* Shim, 0.030" thick GW-1166-3* Shim, 0.
28 MODELS 643C, 643B & 645A 22 37 17 15 27 20 47 23 29 8 37 17 32 27 15 20 6 26 1 10 1 4 16 18 43 11 15 9 37 24 38 3 44 19 27 14 13 40 45 12 46 34 21 48 44 23 5 23 39 48 99 36 32 6 3 44 33 28 35 3.
29 MODELS 643C, 643B & 645A REF NO. P ART NO. DESCRIPTION 1 736-0159 Flat Washer, 5/16 2 756-04198 Pulley, Engine Drive 3 656-04023 Transmission Pulley (A) 656-04005 Transmission Pulley (B) (C) 4 .
30 NOTES.
31 NOTES.
TR O Y -BIL T TILLER LIFETIME LIMITED W ARRANTY WHAT PRODUCT All Troy-Bilt brand ed rear tine walk-behind tillers with gear drive transmissions. IS COVERED This warranty begins on the date of p urchase and is warranted by Troy-Bilt LLC for the life of the tiller, to the or iginal purchaser on ly.
Ein wichtiger Punkt beim Kauf des Geräts Troy-Bilt 645A Super Bronco (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Troy-Bilt 645A Super Bronco noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Troy-Bilt 645A Super Bronco - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Troy-Bilt 645A Super Bronco reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Troy-Bilt 645A Super Bronco erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Troy-Bilt 645A Super Bronco besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Troy-Bilt 645A Super Bronco verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Troy-Bilt 645A Super Bronco. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Troy-Bilt 645A Super Bronco gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
