Benutzeranleitung / Produktwartung 52058 des Produzenten Troy-Bilt
Zur Seite of 24
GARDEN WAY INCORPORATED OWNER’S MANUAL T rimmer/ Mower • Safety • Assembly • Features/Controls • Operation • Maintenance • Parts List Models 52057 – 5 HP Recoil Star t 52058 – 6HP Electric Star t (Electric Start Model Shown) $4 .
SECTION 1: SAFETY ...........................................1 General Operation ......................................................1 Slope Operation .........................................................2 Children...............................
1 Under California law, and under the laws of several other states, you are not permitted to operate an internal combustion engine using hydrocarbon fuels on any forest covered, brush covered, or gras.
2 Section 1: Safety 20. Always wear approved safety gog- gles or safety glasses with side shields when operating equipment. The use of any powered machine can result in for- eign objects being thrown by high- speed rotating parts which can cause personal injury or property damage.
3 Section 1: Safety and debris shield. Make sure they are not ben t, dam age d, o r loose. 10. Only use eighteen-inch long .130" or .155" diameter trimmer line. N ever use other lengths, diameters or material as trimmer line. 11. Trimmer line moves at high speed and can cut.
4 Introduction Carefully follow these assembly steps to correctly prepare your machine for use. It is recommended that you read this Section in its entirety before begin- ning assembly. NOTE: If an assembly step applies only to certain models, those models are noted at the beginning of that step.
5 Section 2: Assembly Figure 2-2: Handlebar installation (electric start model shown). A C D F E B G F O M M Figure 2-4: Check trimmer head hard- ware for tightness. 5. Use two cable ties (F, Figure 2-2) to secure the trimmer head control cable (C) and the electrical wiring har- ness (O) to the handlebar at the loca- tions shown.
6 Section 2: Assembly STEP 6: Connect and Charge Battery (Electric Start Models) 1 . Lift and tilt debris shield (X, Figure 2-5) forward to view battery (P). Connect the red wire (R, Figure 2-6) to the positive (+) red-coded terminal on the battery. Then, connect the black wire (S) to the negative ( – ) black- coded terminal on the battery.
7 Features and Controls 3 Section Operating Symbols Various symbols (shown here, with word descrip- tions) are used on the unit. STOP FEA TURES AND CONTROLS This Section describes the location and function of the features and controls on your machine.
8 PRE-ST ART CHECKLIST 1. Review Section 1: Safety and also Section 3: Features and Controls. 2. Check for loose or missing hard- ware. Tighten or replace as needed. 3. Check the engine oil level*. It must be up to the “ FULL ” mark on the oil dipstick.
9 Section 4: Operation USE THE CORRECT DIAMETER TRIMMER LINE Before starting a project, examine the grass or material you will be cutting and trimming. For tougher conditions, use two (or four) sections of the thicker gauge, .155" diameter extra-heavy duty line.
10 Tips for Precision Cutting For the most precise cutting possible, be sure to select the appropriate line cutting height and trimmer line size (thickness) for the conditions at hand. When mowing, let the cutting head rest lightly on the ground and do not lift up on the handlebars.
11 ADJUSTING TRIMMER HEAD ENGAGEMENT The tension on the drive belt must be correct for proper operation of the trimmer head. If the tension is correct, the trimmer head will rotate when the Trimmer He.
REMOVING AND REPLACING THE TRIMMER HEAD 1. Stop the engine and wait for all moving parts to stop. Disconnect spark plug wire and move it away from the spark plug. Remove the ignition key on electric start models. 2. Two bolts (A, Figure 5-3) secure the trimmer head (B) to the spindle head (C).
13 Section 5: Maintenance Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Remove ignition key on electric start models.
14 Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Remove ignition key on electric start models. Failure to follow these instructions can result in serious personal injury or property damage.
15 Section 5: Maintenance damage caused by overspeeding. Do not tamper with the governor settings. Seek authorized service if you think an adjust- ment is required.
16 Section 5: Maintenance Before inspecting, cleaning or servicing the machine, shut off engine, wait for all moving parts to come to a complete stop, disconnect spark plug wire and move wire away from spark plug. Remove ignition key on electric start models.
17 Section 5: Maintenance PROBLEM POSSIBLE CAUSE CORRECTION Engine does not start. 1. Spark plug wire disconnected. 1. Reconnect wire. 2. Defective or incorrectly gapped spark plug. 2. Inspect/replace spark plug. 3. Fuel tank empty. 3. Add fuel. 4. Dirty carburetor or fuel line.
18 Parts List Models 52057 & 52058 DRA WING NO. 1 1 2 3 4 5 5 5 5 5 5 7 8 9 10 11 12 13 17 17 17 16 20 21 22 23 24 25 15 18 19 14 14 6 6.
19 Models 52057 and 52058 Parts List 1 1917765 Debris Guard ............................................ 1 2 1918082 Decal-Logo (B) ......................................... 1 1904401 Decal-Logo (A) ......................................... 1 3 1915290 Push-in Fastener .
20 Parts List Models 52057 & 52058 DRA WING NO. 2 See DRAWING NO. 1 See DRAWING NO. 3 See ACCESSORIES AND KITS 2 2 1 1 3 3 4 7 8 9 10 11 12 13 14 15 16 27 17 18 22 23 24 25 26 18 18 19 20 21 6 1 1917778 Wheel/Tire Assembly ........................
21 DRA WING NO. 3 1 4 5 2 3 6 6 8 7 9 12 13 13 13 14 15 16 14 10 11 1 1918283 Upper Handlebar (Incl. Refs. 2 & 3) ....... 1 2 1915889 Decal – Bail Engage/Disengage ................ 1 3 1918304 Decal – Throttle .................................
CUSTOMER SERVICE INFORMA TION Owner Registration Card Please fill out and mail the enclosed owner registration card. The purpose of this card is to register each unit at the factory in order to keep the owner informed with informational bulletins and safety literature.
Ein wichtiger Punkt beim Kauf des Geräts Troy-Bilt 52058 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Troy-Bilt 52058 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Troy-Bilt 52058 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Troy-Bilt 52058 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Troy-Bilt 52058 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Troy-Bilt 52058 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Troy-Bilt 52058 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Troy-Bilt 52058. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Troy-Bilt 52058 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
