Benutzeranleitung / Produktwartung Bluetooth Print Adapter des Produzenten TROY Group
Zur Seite of 34
User’s Guide Bluetooth TM Print Adapter Par t Number 40150-100 Revision 1.0 TM.
ii Copyright Notice All rights reserved. N o part of this publication may be reproduced, stored, in a retrieval system, or transmitted in any form or by any means, electronic, mechani- cal, photocopying, recording, or otherwise, without the prior written permission of TR O Y G roup, I nc.
Contents Introduction Windows S ystem Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 About Y our U ser’ s Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 1 Installing the WindConnect P rint Adapter Har dware U npacking and Handling .
iv.
Introduction The TR OY WindConnect TM Bluetooth TM P rint Adapter is a device that enables wireless communications capabilities on most models of printers. By using the WindConnect, you can conveniently print fr om laptop computers and other devices without using a cable, as shown in the diagram below .
Windo ws TM System Requir ements T o use the WindConnect Bluetooth P rint Adapter for printing from a PC, your system should include: ◗ An IBM-compatible PC with P entium 133MHz or higher processor .
1-1 Installing the WindConnect Print Adapter Hardware The WindConnect B luetooth P rint Adapter plugs directly into the parallel port of the printer . If desired you can simultaneously use the printer’ s USB port for a hardwired connection to your PC.
1-2 Before Y our Begin Before you install the WindConnect Bluetooth P rint Adapter , make sure that your printer and your laptop computer already function properly via a parallel or USB printer cable. Refer to your printer’ s documentation for instructions on using and maintaining your printer .
Connecting to the P rinter Before connecting the WindConnect Bluetooth Print A dapter , make sure that the printer is turned off. The WindConnect has a 36-pin male Centr onics parallel connector that is compat- ible with the 36-pin female connectors found on most printers.
1-4 ing activity . Since you have not made a connection y et, both of these LEDs should be off. V erifying the Connection to the P rinter Before attempting to print, it is very important to verify the connection between the WindConnect and the printer .
Configuring the Software on Y our PC Y ou can now configure a laptop PC to print wirelessly to your EPSON printer equipped with an WindConnect Bluetooth P rint Adapter . T o do this, you will use the WindConnect P ort Monitor software, which is included on the installation CD-R OM.
one of these older cards, first install the software and then upgrade the software using the Bluetooth Software Suite Upgrade included on the WindConnect installation CD-ROM. Y ou must then verify that the Serial P ort Profile is enabled on the B luetooth Software S uite.
rectly installed the Bluetooth PCMCIA car d and software). Click on any one of these ports and verify that the Serial P or t P rofile is checked. If it is not checked, then click the box next to Serial Port Profile .
3. Right-Click on the printer you wish to associate with the network port, and select Properties . 4. If you are using Windows NT/2000/XP , go to the Ports tab. I f you are using Windows 95/98/ME, go to the Details tab . 5. Click on Add Port . 6. If you ar e using Windows NT/2000/XP system, highlight T roy Bluetooth Port , and click New Port .
2-5 If you are running Windows 95/98/ME, select Other , highlight T roy Group T roy Bluetooth Port , and click OK . 7. The TROY Bluetooth Port Monitor screen will appear and the Bluetooth port name will be displayed. If this is your first port, it will be called TBT1 .
If you are running Windows 95/98/ME, the Details tab should look some- thing like this: Y ou are now ready to print. P rinting the First Job Y ou should now be able to print in the usual manner from any standard W indows application program. Go to File and then Print.
2-7 This screen will show all of the av ailable WindConnect Bluetooth print adapters. If this is your first print adapter installation, you will only see one print adapter .
2-8 Disconnecting Y our Bluetooth connection will automatically be disconnected after one minute of inactivity . Y ou can change this parameter by right clicking on the Windows print- er icon for your printer and clicking on Properties .
Configuring Other Devices The WindConnect Bluetooth P rint Adapter is designed to allow printing from a variety of different Bluetooth devices. S uch devices must support the Bluetooth Serial P ort Profile, the Object P ush P rofile, or the LAN A ccess Profile in or der to work with the W indConnect Bluetooth Print Adapter .
Bluetooth TBT1 port. This procedure is similar to the procedure described in the Adding a Windows P rinter section of the previous chapter except that the local port is the COM port you created in step 1 instead of TBT1.
3-3 2. Y ou should see the Discover icon. If you don ’ t, scroll down by clicking on the scroll bar arrows on the left side of the screen. Click the Discover icon. 3. Click the Inquire button. Y ou get a message “starting inquiry” and then a list of addresses of available W indConnect Bluetooth Print A dapter devices and other devices.
4. Click OK . 5. If desir ed, change the Driver Name to match your printer (the standar d Generic driver will work with most printers, but will not handle graphics). 6. Click Set As Default to save the settings and then click on the Home button to return to the main menu.
name or the address, depending on the program) and associate the W indConnect Bluetooth P rint Adapter’ s P1 ser vice. Y ou should now be able to print.
1. T urn the phone on by holding do wn the No key for several seconds. 2. P ush the right arrow key five times until you see 5 Extras . 3. P ush the Ye s key . 4. P ush the 4 key to select Bluetooth . 5. Click the 3 key to discover the available B luetooth devices on the network.
4-1 Using the Serial Port The WindConnect has an RS-232 serial port that can be used to connect a console terminal, a serial printer , or a wide variety of other RS-232-compatible devices. The connector is an RJ45 modular jack similar to the type used on E thernet networks (but not electrically compatible).
By default the serial port is set in console mode. In this mode, the port settings are permanently fixed at 115.2Kbps, 8-bit characters, no parity , and no flow control, and console operation. The console contains a variety of configuration and diagnostic commands.
T roubleshooting If Y ou Can ’ t Print If you are unable to print fr om your laptop or other device to the W indConnect Bluetooth P rint Adapter , then check the following: 1. Make sure that the gr een light is on when you are printing. If it is not on, then there is no Bluetooth wireless connection.
5-2.
Where to Get Help TR OY offers several customer support options to assist you in the event you expe- rience difficulties with your W indConnect, including telephone support, repair services, extended warranty , and advance replacement.
Retur ning Products If you need to return a TRO Y product for any reason (failures, incorr ect ship- ments, etc.), first contact TR OY at +1 (208) 955-1000 (Americas, Asia, and Australia) or +49 (0) 7032-9454-21 (Europe and A frica) and request a Return Authorization N umber from the TR O Y T echnical S uppor t Gr oup.
Notices FCC Compliance Statement F or U nited States U sers This equipment has been tested and found to comply within the limits for a Class B digital device pursuant to P art 15 of the FCC Rules. These limits are designed to provide r easonable protection against harmful interference in a residential installation.
F or European U sers This product is in conformity with the protection requir ements of EU Council Directiv e 89/336/EEC on the approximation of the laws of the M ember States relating to electromagnetic compatibility .
REGULA T ORY INFORMA TION European U nion (EU) TR OY hereb y declares that the Bluetooth™ wir eless technology built into the WindConnect P rint Adapter , is in compliance with the essential requirements and other relevant pro visions of European Directiv e 1999/5/EC.
The radiated output power of WindConnect is far below the FCC radio frequen- cy exposure limits. N evertheless, the WindConnect shall be used in such a man- ner that the potential for human contact during normal operation is minimized.
Ein wichtiger Punkt beim Kauf des Geräts TROY Group Bluetooth Print Adapter (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie TROY Group Bluetooth Print Adapter noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für TROY Group Bluetooth Print Adapter - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von TROY Group Bluetooth Print Adapter reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über TROY Group Bluetooth Print Adapter erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon TROY Group Bluetooth Print Adapter besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von TROY Group Bluetooth Print Adapter verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit TROY Group Bluetooth Print Adapter. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei TROY Group Bluetooth Print Adapter gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
