Benutzeranleitung / Produktwartung MX2004A des Produzenten Behringer
Zur Seite of 26
www.behringer.com Version 1.1 March 2001 User’s Manual ENGLISH EURORACK ® MX2004A.
2 EURORACK MX2004A This symbol, wherever it appears, alerts you to the presence of uninsulated dangerous voltage inside the enclo- sure—voltage that may be sufficient to constitute a risk of shock. This symbol, wherever it appears, alerts you to important operating and mainte- nance instructions in the accompanying literature.
3 EURORACK MX2004A FOREWORD Dear Customer, Welcome to the team of EURORACK users and thank you very much for expressing your confidence in BEHRINGER products by purchasing this unit.
4 EURORACK MX2004A EURORACK MX2004A Ultra low-noise 20-channel, 4-bus mixer s 8 mono input channels with gold-plated XLRs and phone connectors s 4 stereo input channels with balanced TRS connectors s .
5 EURORACK MX2004A T ABLE OF CONTENTS 1 . INTRODUCTION ..................................................................................................................... 7 1. 1 Architecture ..........................................................
6 EURORACK MX2004A 7 . TECHNICAL BACKGROUND .............................................................................................. 20 7. 1 Mixing .................................................................................................
7 EURORACK MX2004A 1. INTRODUCTION Congratulations. In purchasing our EURORACK you have acquired a mixer with incredible versatility and audio performance. Your EURORACK is built to the same outstanding quality as our top-of-the range console, the BEHRINGER EURODESK MX9000.
8 EURORACK MX2004A 1.2 Before you begin 1.2.1 PSU (power supply unit) Any amplifier circuit is limited in its transient response by the available current. Every mixer has numerous line level operational amplifiers (op-amps) inside. When being driven hard, many desks begin to show signs of stress due to power supply limitations.
9 EURORACK MX2004A For level-setting (as opposed to localized listening) select the mono PFL bus rather than the post-fader (post- channel pan) stereo solo bus (CHANNEL MODE global switch up). PFL/solo never interrupts the mix at the main recording outputs.
10 EURORACK MX2004A 2.5 Insert Insert points are useful for adding dynamic processing or equalization to a channel or the mix. Unlike reverbs etc., which are usually added to the dry signal, dynamic processing is normally applied across an entire signal.
11 EURORACK MX2004A 4.2 Stereo aux returns There are two additional stereo line inputs (aux returns 1 and 2) on your MX2004A. Aux returns 1 is perma- nently assigned to the main mix. If you connect a jack to the left socket only, the aux return 1 operates in mono.
12 EURORACK MX2004A 4.5 2-track input and output Input A 2-track input, on RCA connectors / , provides easy connection to DAT and other professional or semi-professional audio equipment. The 2-track input is primarily for auditioning mix playback from tape.
13 EURORACK MX2004A 5. SETTING UP 5.1 Selecting inputs 1 ) Mono channels accept microphone or line inputs. If you are using the microphone input, make sure nothing is connected to the line input (and vice-versa). + The microphone inputs are more sensitive than the line inputs.
14 EURORACK MX2004A 5.5 Multitrack initialization Set up the multitrack so that any track in “record ready” condition has its input monitored when the tape is stationary. Place all tracks to be recorded into “record ready” status. (Once a recording has been made, these tracks should automatically switch to tape playback.
15 EURORACK MX2004A K e y b o a r d M ixer S ourc e Mi c /Li ne Mono/ S tereo I nput MIDI I ns t rum ent #1 Line Mono 1 MIDI I ns t rum ent #2 Line Mono 2 MIDI I ns t rum ent #3 Line Mono 3 MIDI I ns .
16 EURORACK MX2004A muddy FOH sound, as well as causing a reduction in feedback thresholds. Don ’ t forget to notch out trouble- some frequencies using a graphic or parametric equalizer, or feedback destroyer (see the BEHRINGER ULTRA-CURVE PRO DSP8024 or the FEEDBACK DESTROYER PRO DSP1124P, which do all of these and more).
17 EURORACK MX2004A Fig. 6.1: Project studio setup example 6. 4 Patchbay A patchbay allows to patch the audio signals of most components in your studio from a central point and send them to other units, which makes your entire cabling better structured and is indispensable for professional work.
18 EURORACK MX2004A 6.4.2 Parallel Fig. 6.2: Patchbay mode “parallel” In this mode, all terminals of one module are interconnected. This configuration doesn ’ t make sense at first glance but is used to split up and send one audio signal (e.g. a ux send) to several destinations (e.
19 EURORACK MX2004A and outputs are positioned on top of each other. Basically, the inputs are routed to the bottom and the outputs to the top rear-wall connectors. Avoid routing digital signals over a patchbay as the pulse signal used for the transmission of such signals causes heavy interference in analog signals.
20 EURORACK MX2004A thus allows for recording both to the DAT recorder and the tape deck, simply by patching it accordingly. Modules 19 & 20 (tape deck) are open, because it does not make sense connecting the inputs and outputs of the tape deck.
21 EURORACK MX2004A voices punch through a mix in a slightly unnatural but exciting way. In general corrective EQ usually involves broadband (slope) contouring, together with narrowband notching of unwanted resonances. The narrower the notch or “ Q ” , the less the total signal will be affected.
22 EURORACK MX2004A AC Power In. For connecting the mixer to the power supply unit (PSU). Always connect mixer and PSU before you connect the PSU to the mains supply. POWER switch . Once the PSU is connected to the mains supply, you may switch on your EURORACK.
23 EURORACK MX2004A Fig. 8.1: Different connector types 8. INSTALLATION.
24 EURORACK MX2004A 8.3 Modifications The following modifications require you to do some soldering. Attempt only if you are experienced in using an iron on PCBs. Otherwise, refer to qualified personnel. After modification the BEHRINGER warranty becomes discretionary.
25 EURORACK MX2004A 9. SPECIFICATIONS Mono input channels Mic input electronically balanced, discrete input configuration Frequency response 10 Hz to 6 0 kHz, +/- 3 dB Distortion (THD & N) 0.007% @ +4 dBu, 1 kHz, bandwidth 80 kHz Mic E.I.N. (22 Hz - 22 kHz) -129.
26 EURORACK MX2004A The information contained in this manual is subject to change without notice. No part of this manual may be reproduced or transmitted in any form or by any means, electronic or mec.
Ein wichtiger Punkt beim Kauf des Geräts Behringer MX2004A (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Behringer MX2004A noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Behringer MX2004A - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Behringer MX2004A reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Behringer MX2004A erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Behringer MX2004A besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Behringer MX2004A verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Behringer MX2004A. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Behringer MX2004A gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.