Benutzeranleitung / Produktwartung TL-WR702N des Produzenten TP-Link
Zur Seite of 175
TL-WR702N 150Mbps Wireless N Nano Router Rev: 1.0.0 1910010547.
- I - COPYRIGHT & TRADEMARKS S pecifications are subjec t to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., L TD. Other br ands and product names are trademarks or registered trademarks of t heir respective holders.
- II - FCC RF Radiation Exposure S t atement This equipment complies with FCC RF radiatio n exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co -located or operating in conjunction with any other antenna or transmitter .
TP-LINK TECHNOLOGIES CO., L TD TP-LINK TECHNOLOGIES CO., L TD . South Building, No.5 Keyuan Road, Central Zone, Science & T echnology Park, Nanshan, Shenzhen, P . R. China DE CLARA TION OF C ONF ORMITY For the following equipment: Product Description: 150Mbp s Wireless N Nano Router Model No.
- I - CONTENTS Package Co ntent s............................................................................................................... ................... 1 Chapter 1. Introduc tion ...........................................................
- II - 5.12 IP & MAC Bind ing Setting ................................................................................................ 94 5.13 Dynamic DNS.............................................................................................
TL-WR702N 150Mbps Wireless N Nano Router - 1 - Package Contents The following items should be found in your package: ¾ One TL-WR702N 150Mbps Wireless N Nano Router ¾ Quick Install ation Guide ¾ One.
TL-WR702N 150Mbps Wireless N Nano Router - 2 - Chapter 1. Introduction Thank you for choosing the TL-WR7 02N 150Mbps Wireless N Nano Router . 1.1 Overview of the Router Small enough to fit in the aver.
TL-WR702N 150Mbps Wireless N Nano Router - 3 - this user guide. Before installing the Router , please look through this guide to know all the Router ’s functions. 1.2 Conventions The Router o r TL-WR 702N me ntione d in this guide s tand s for TL-WR702N 1 5 0 M b ps W i r e l es s N N ano Router without any explanation.
TL-WR702N 150Mbps Wireless N Nano Router - 4 - 1.4 Panel Layout Figure 1-1 T L-WR702N sketch ¾ LED Statu s Indication Solid It’s powered on but the LA N/W AN port is not connected. Flashing Slowly The LAN/W AN cable is connected but there is no data being transmitted or received.
TL-WR702N 150Mbps Wireless N Nano Router - 5 - Chapter 2. Connecting the Router 2.1 System Requirement s ¾ Each PC in the LAN needs a working Ethernet Adapter ¾ TCP/IP protocol must be inst alled on each PC ¾ Web browser , such as Microsoft Internet Explorer 5.
TL-WR702N 150Mbps Wireless N Nano Router - 6 - 2.3.1 AP Mode As the supplement of wi red LAN, TL-WR702N enables the wir ed LAN to connect to the Internet wirelessly .
TL-WR702N 150Mbps Wireless N Nano Router - 7 - Figure 2-2 Hardware Installation of the TL-WR702N in Router Mode 1. Connect the W AN port of TL-WR702N to the LAN Port on the DSL/Cable Modem. 2. Connect the W AN port on the DSL/C able Modem to the wired Internet.
TL-WR702N 150Mbps Wireless N Nano Router - 8 - ) Note: It is recommended that you connect a PC/notebook to the LAN port of the Router with an Ethernet cable, and then login the Router from the PC/notebook to se t the Router in AP Repeater mode.
TL-WR702N 150Mbps Wireless N Nano Router - 9 - Figure 2-5 Hardware Installation of the TL-WR702N in Client Mode 1. Connect the PC to the LAN/W AN port of TL-WR702N router with an Ethernet cable. 2. Plug the power plug of TL-WR7 02N in electrical wall socket.
TL-WR702N 150Mbps Wireless N Nano Router - 10 - Chapter 3. Quick Installation Guide This chapter will show you how to configure the basic functi ons of your TL-WR702N 150Mbps Wireless N Nano Router using Quick Setup Wi za rd within minutes. 3.1 TCP/IP Configuration The default IP address of the TL-WR702N 150Mbps Wireless N Nano Router is 192.
TL-WR702N 150Mbps Wireless N Nano Router - 1 1 - Figure 3-1 Success result of Ping command ¾ If the result displayed is similar to the Figure 3-2, it means the connection between your P C and the Router has failed. Figure 3-2 Failure result of Ping command Please check the connection following these step s: 1.
TL-WR702N 150Mbps Wireless N Nano Router - 12 - 3.2 Quick Inst allation Guide With a Web-based utility , it is easy to configure and manage the TL-WR702N 150Mbps Wireless N Nano Router .
TL-WR702N 150Mbps Wireless N Nano Router - 13 - 3. Click Next , and then Working Mode p age will appear , shown in Figure 3-5. Figure 3-5 Quick Setup - W orking Mode ) Note: The Router supports five worki ng modes for multi-user to acce ss the Internet: AP, Router, Repeater, Bridge and Client.
TL-WR702N 150Mbps Wireless N Nano Router - 14 - Figure 3-6 Quick Setup - Wireless AP ¾ Wireless Radio - Enable or disable the wireless radi o choosing from the pull-down list. ¾ SSID - Enter a string of up to 32 characters. The same name of SSID (Service Set Identification) must be assigned to all wire less devices in your network.
TL-WR702N 150Mbps Wireless N Nano Router - 15 - • 11bg mixed - Select if you are using both 802.11b and 802.11g wireless clients. • 11bgn mixed - Select if you are using a mix of 802.11b, 11g, and 11n wireless clients. Select the desired wireless mode.
TL-WR702N 150Mbps Wireless N Nano Router - 16 - Figure 3-8 Quick Setup – Finish 3.2.2 Router Mode When you choose Router on Working Mode p age in Figure 3-5 , take the following steps: 1. Click Next in Figure 3-5 , and you will see the followi ng scree n.
TL-WR702N 150Mbps Wireless N Nano Router - 17 - Figure 3-10 Quick Set up - WAN Connection Type The Router supports three popular ways PPPoE , Dynamic IP and Static IP to connect to the Internet. T o make sure the connection type your IS P provides, please refer to the ISP .
TL-WR702N 150Mbps Wireless N Nano Router - 18 - Figure 3-12 Quick Setup - S tatic IP 3. Click Next , you will see the Finish page as shown in Figure 3-13. Click the Reboot button to make your wireless configuration take ef fect and finish the Quick Setup.
TL-WR702N 150Mbps Wireless N Nano Router - 19 - Figure 3-14 Quick Setup - Wireless Repeater ¾ SSID - The SSID of AP that you want to access. ¾ MAC of AP - The MAC address of AP that you want to access. ¾ Region - Select your region from the pull-down lis t.
TL-WR702N 150Mbps Wireless N Nano Router - 20 - Figure 3-15 AP List ) Note: If you know the SSID of the desired AP , you can al so input it into the field "SSID" manually . 2. Click the Next button in Figure 3-14. Y ou will then see the Fin ish page.
TL-WR702N 150Mbps Wireless N Nano Router - 21 - Figure 3-16 Quick Setup - Finish 3.2.4 Bridge Mode When you choose Bridge on Working Mode p age in Figure 3-5 , take the following steps: 1. Click Next , and then Wireless Repeater page will appear as shown in Figure 3-17.
TL-WR702N 150Mbps Wireless N Nano Router - 22 - ¾ Region - Select your region from the pull-down lis t. This field specifies the region w here the wireless function of the Router can be used. It may be illegal to use the wireless function of the Router in a region other than one of those specified in this field.
TL-WR702N 150Mbps Wireless N Nano Router - 23 - ¾ PassWord - If the AP your Router is going to co nnect needs password, you need to fill the password in this blank. Click Survey button on the Wireless page as sh own in Figure 3-17, and then AP List page will appear as shown in Figure 3-18.
TL-WR702N 150Mbps Wireless N Nano Router - 24 - Figure 3-19 Quick Setup - Wireless Security Settings This page is for setting wireless security of y our ow n AP . When computers and mobile phones are connected to the AP , they s hould input the same password.
TL-WR702N 150Mbps Wireless N Nano Router - 25 - Figure 3-21 Quick Setup - Wireless Client ¾ SSID - Enter the SSID that you want to access. ¾ MAC of AP - Enter the MAC address of AP that you want to access. ¾ Region - Select your region from the pull-down list.
TL-WR702N 150Mbps Wireless N Nano Router - 26 - Figure 3-22 AP List 3. Click the Next button in Figure 3-23. Y ou will then see the Fin ish page. Click the Reboot button to make your wireless configurati on take ef fect and finish the Quick Setup.
TL-WR702N 150Mbps Wireless N Nano Router - 27 - ) Note: 1. The operating distance or range of your wire less connection varies si gnificantly based on the physical placement of the Router . Fo r best results, place your Router . z Near the center of the area in which your wireless stations will operate.
TL-WR702N 150Mbps Wireless N Nano Router - 28 - Chapter 4. Configuration for AP Mode This chapter will show each Web p age's key f unctions and the configurat ion way for AP Mode of TL-WR702N. 4.1 Login After your successful login, you can configur e and manage the device.
TL-WR702N 150Mbps Wireless N Nano Router - 29 - Figure 4-2 S tatus ¾ Firmware V ersion - The version information of the Router ’s firmware. ¾ Hardware V ersion - The version information of the Router ’s hardware. ¾ LAN - This field displays the current settings or information for the LA N, you can configure them in the Network > LAN page.
TL-WR702N 150Mbps Wireless N Nano Router - 30 - • Channel Wid th - The current wireless channel width in use. • MAC address - The physical address of the Router , as seen from the WLAN. • WDS St atus - The status of WDS connection. ¾ Syst em Up Time - The length of the time since the Router was last power ed on or reset.
TL-WR702N 150Mbps Wireless N Nano Router - 31 - Figure 4-4 4.5 Network Figure 4-5 the Network menu There is only one submenu under the Network menu (shown in Figure 4-5): LAN . 4.5.1 LAN Choose menu “ Network → LAN ”, and then you can conf igure the IP parameters of th e LAN on the screen as below .
TL-WR702N 150Mbps Wireless N Nano Router - 32 - 4.6 Wireless Figure 4-7 Wireless menu There are five submenus under the Wireless menu (shown in Figure 4-7): Wireless Settings , Wireless Security , MAC Filtering, W ireless Ad vanced and Wireless St atistics.
TL-WR702N 150Mbps Wireless N Nano Router - 33 - name (SSID) to a different value. This value is case-sensitive. For example, TEST is NOT the same as test . ¾ Region - Select your region from the pull-down lis t. This field specifies the region w here the wireless function of the Router can be used.
TL-WR702N 150Mbps Wireless N Nano Router - 34 - ¾ SSID (to be bridged) - The SSID of the AP your Router is going to connect to as a client. You can also use the search func tion to select the SSID to join. ¾ BSSID (to be bridged) - The BSSID of the AP your Router is going to connect to as a client.
TL-WR702N 150Mbps Wireless N Nano Router - 35 - 2. Failure to follow these gui delines can result in significant performance degradation or inabi lity to wirelessly connect to the Router . 4.6.2 Wireless Security Choose menu “ Wi rel es s → Wireless Security ”, and then you can configure the security settings of your wireless network.
TL-WR702N 150Mbps Wireless N Nano Router - 36 - • Typ e - you can choose the type for the WEP se curity on the pull-down list. The default setting is Automatic , which can select Shared Key or Open System authentication type automatically based on the wirele ss station's capability and request.
TL-WR702N 150Mbps Wireless N Nano Router - 37 - key of WPA) or WP A2-PSK (Pre-shared key of WPA) autom atically based on the wireless station's capability and request. • Encryption - When WPA-PSK or WPA is set as the Authenticat ion Type, you can select Automatic (Recommended) , TKIP or AES as Encryption.
TL-WR702N 150Mbps Wireless N Nano Router - 38 - ¾ Description - A simple description of the wireless station. To Add a Wireless MAC Addre ss filtering entry, click the Add N ew … button.
TL-WR702N 150Mbps Wireless N Nano Router - 39 - 1. Click the Enable button to enable this function. 2. Select the radio button “Allow the stations specifi ed by any enabled entries in the list to access” for Filtering Rules . 3. Delete all or disable all entries if there are an y entries already.
TL-WR702N 150Mbps Wireless N Nano Router - 40 - ¾ Transmit Power - Here you can specify the transmit power of Router. You can select High, Middle or Low which you would like. High is the default setting and is recommended. ¾ Beacon Interval - Enter a value between 20-1000 millise conds for Beacon Interval here.
TL-WR702N 150Mbps Wireless N Nano Router - 41 - Figure 4-13 Wireless S tatistics ¾ MAC Address - The connected wireless station's MAC address ¾ Current Status - The connected wireless stat ion&.
TL-WR702N 150Mbps Wireless N Nano Router - 42 - Figure 4-15 DHCP Setting s ¾ DHCP Server - Enable or Disable the DHCP server . If you disable the Server , you must have another DHCP server within your network o r else you must configure the computer manually .
TL-WR702N 150Mbps Wireless N Nano Router - 43 - 4.7.2 DHCP Clients List Choose menu “ DHCP → DHCP Client s List ”, and then you can view the information about the clients attach ed to the Router in the screen as shown in Figure 4-16.
TL-WR702N 150Mbps Wireless N Nano Router - 44 - ¾ Status - The status of this entry either Enabled or Disabled . To Reserve an IP address: 1. Click the Add New… button. Then Figure 4-18 will pop-up. 2. Enter the MAC address (in XX-XX-XX-XX-XX-XX format.
TL-WR702N 150Mbps Wireless N Nano Router - 45 - Choose menu “ System T ools ”, and then you can see the submenus under the main menu: Diagnostic , Firm w are , Factory Default s, Backup & Restor e, Reboot, Password, and S ystem Log. Click any of them, and you will be able to c onfigure the corresponding function.
TL-WR702N 150Mbps Wireless N Nano Router - 46 - ¾ IP Address/Domain Name - T ype the destination IP address (e.g. 202.108.22.5) or Domain name (e.g. http://www .tp-link.com). ¾ Pings Coun t - The number of Ping packe ts for a Ping connection. The default is 4.
TL-WR702N 150Mbps Wireless N Nano Router - 47 - ¾ Hardware Version - This displays the current hardware version. The hardware version of the upgrade file must accord with the R outer’s current hardware version. T o upgrade the Router's firmware, follow these instructions below: 1.
TL-WR702N 150Mbps Wireless N Nano Router - 48 - ) Note: All changed settings will be lost when defaults are restored. 4.8.4 Backup & Restore Choose menu “ System T ools → Backup & Restore .
TL-WR702N 150Mbps Wireless N Nano Router - 49 - • Change the LAN IP Address (syst em will reboot automatically). • Change the DHCP Settings. • Change the Wireless configurations. • Change the Web Management Port. • Upgrade the firmware of the Router (system will reboot automatically).
TL-WR702N 150Mbps Wireless N Nano Router - 50 - 4.8.7 System Log Choose menu “ System T ools → S ystem Log ”, and then you can view the logs of the Router. Figure 4-27 System Log ¾ Refresh - Refresh the page to show the latest log list. ¾ Clear All - All the logs will be deleted from the Rout er permanently, not just from the page.
TL-WR702N 150Mbps Wireless N Nano Router - 51 - Chapter 5. Configuration for Router Mode This chapter will show each W eb page's key functions and the confi guration way for Router Mode of TL-WR702N. 5.1 Login After your successful login, you can configur e and manage the device.
TL-WR702N 150Mbps Wireless N Nano Router - 52 - Figure 5-2 ¾ Firmware V ersion - The version information of the Router ’s firmware. ¾ Hardware V ersion - The version information of the Router ’s hardware.
TL-WR702N 150Mbps Wireless N Nano Router - 53 - ¾ LAN - This field displays the current settings or information for the LA N, you can configure them in the Network > LAN page. • MAC Address - The physical address of the Rout er , as seen from the LAN.
TL-WR702N 150Mbps Wireless N Nano Router - 54 - • Received (Packets) - T raffic that counted in pa ckets has been received out from the W AN port. ¾ Syst em Up Time - The length of the time since the Router was last power ed on or reset. Click the Refresh button to get the latest stat us and settings of the Router .
TL-WR702N 150Mbps Wireless N Nano Router - 55 - 5.5 Network Figure 5-5 the Network menu There are three submenus under the Network menu (shown in Figure 5-5): WA N , LAN a nd MAC Clone. Click any of them, and you will be able to configure the corresp onding function.
TL-WR702N 150Mbps Wireless N Nano Router - 56 - This page displays the WAN IP parameters as signed dynamically by your ISP , including IP address, Subnet Mask, Default Gateway , etc. Click the Renew button to renew the IP p arameters from your ISP . Click the Release button to release the IP p arameters.
TL-WR702N 150Mbps Wireless N Nano Router - 57 - ¾ IP Address - Enter the IP address in dotted-decimal not ation provided by yo ur ISP . ¾ Subnet Mask - Enter the subnet Mask in dotted-decimal notation provided by your ISP , usually is 255.255.255.0.
TL-WR702N 150Mbps Wireless N Nano Router - 58 - ¾ Secondary Connection - It’ s available only for PPPoE Connec tion. If your ISP provides an extra Connection type such as Dynamic/St at ic IP to connect to a local area network, then you can check the radio button of Dynamic/S tatic IP to activate this secondary connection.
TL-WR702N 150Mbps Wireless N Nano Router - 59 - Figure 5-9 PPPoE Advanced Settings ¾ MTU Size - The default MTU size is “1480” bytes, which is usually fine.
TL-WR702N 150Mbps Wireless N Nano Router - 60 - Figure 5-10 W AN – L2TP/Russia L2TP ¾ User Name/Password - Enter the User Name and Password provided by your ISP . These fields are case-sensitive. ¾ Dynamic IP/ St atic IP - Choose either as you are gi ven by your ISP .
TL-WR702N 150Mbps Wireless N Nano Router - 61 - ¾ Connect Manually - Y ou can configure the Route r to make it connect or disconnect manually . After a specified period of inactivity ( Max Idle Time .
TL-WR702N 150Mbps Wireless N Nano Router - 62 - ¾ User Name/Password - Enter the User Name and Password provided by your ISP . These fields are case-sensitive. ¾ Dynamic IP/ S tatic IP - Choose either as you are gi ven by your ISP and enter the ISP’s IP address or the domain name.
TL-WR702N 150Mbps Wireless N Nano Router - 63 - 5.5.2 LAN Choose menu “ Network → LAN ”, and then you can conf igure the IP parameters of th e LAN on the screen as below . Figure 5-12 LAN ¾ MAC Address - The physical address of the LAN ports , as seen from the LAN.
TL-WR702N 150Mbps Wireless N Nano Router - 64 - Some ISPs require that you re gister the MAC Address of your adapter . Changes are rarely needed here. ¾ WAN MAC Address - This field displays the current MAC address of the WAN port.
TL-WR702N 150Mbps Wireless N Nano Router - 65 - Figure 5-15 Wireless Settings - Router ¾ SSID - Enter a string of up to 32 characters. The same name of SSID (Service Set Identification) must be assigned to all wireless devices in your network.
TL-WR702N 150Mbps Wireless N Nano Router - 66 - Select the desired wireless mode. When 802. 11g mode is selected, only 802.11g wireless stations can connect to the R outer. When 802.11n mode is se lected, only 802.11n wireless stations can connect to the AP.
TL-WR702N 150Mbps Wireless N Nano Router - 67 - ¾ Authentication Type - This option should be c hosen if the key type is WEP (ASCII) or WEP (HEX). It indicates the authoriz ation type of the Root AP. ¾ Password - If the AP your Router is going to c onnect needs password, you need to fill the password in this blank.
TL-WR702N 150Mbps Wireless N Nano Router - 68 - Figure 5-16 Wireless Security ¾ Disable Security - The wireless security function can be enabled or disabled . If disabled, the wireless stations will be able to con nect the Ro uter without encryption.
TL-WR702N 150Mbps Wireless N Nano Router - 69 - • WEP Key (Password) - Select which of the four keys will be used and enter the matching WEP key that you create. Make sure these val ues are identical on all wireless stations in your network. • Key Type - You can select the WEP key length (64-bit, or 128-bit, or 152-bit.
TL-WR702N 150Mbps Wireless N Nano Router - 70 - For ASCII , the key can be made up of any numbe rs 0 to 9 and any letters A to Z, the length should be between 8 and 63 characters. For Hexadecimal , the key can be made up of any numbers 0 to 9 and letters A to F, the length should be between 8 and 64 characters.
TL-WR702N 150Mbps Wireless N Nano Router - 71 - Figure 5-18 Add or Modify Wirele ss MAC Address Filtering entry To add or modify a MAC Address Filtering entry, follo w these instructions: 1. Enter the appropriate MAC Address into the MAC Address field.
TL-WR702N 150Mbps Wireless N Nano Router - 72 - 3. Delete all or disable all entries if there are any entries already. 4. Click the Add New... button. 1) Enter the MAC address 00-0A-EB-B 0-00-0B/00-0 A-EB-00-07-5 F in the MAC Address field. 2) Enter wireless station A/B in the Description field.
TL-WR702N 150Mbps Wireless N Nano Router - 73 - ¾ Beacon Interval - Enter a value between 20-1000 millise conds for Beacon Interval here. The beacons are the packets sent by the Router to synchr onize a wireless network. Beaco n Interval value determines the time interval of the beacons.
TL-WR702N 150Mbps Wireless N Nano Router - 74 - Figure 5-20 Wireless S tatistics ¾ MAC Address - The connected wireless station's MAC address ¾ Current Status - The connected wireless stat ion&.
TL-WR702N 150Mbps Wireless N Nano Router - 75 - Figure 5-22 DHCP Setting s ¾ DHCP Server - Enable or Disable the DHCP server . If you disable the Server , you must have another DHCP server within your network o r else you must configure the computer manually .
TL-WR702N 150Mbps Wireless N Nano Router - 76 - 5.7.2 DHCP Clients List Choose menu “ DHCP → DHCP Client s List ”, and then you can view the information about the clients attach ed to the Router in the screen as shown in Figure 5-23.
TL-WR702N 150Mbps Wireless N Nano Router - 77 - ¾ Status - The status of this entry, either Enabled or Disabled . To Reserve an IP address: 1. Click the Add New… button.
TL-WR702N 150Mbps Wireless N Nano Router - 78 - 5.8.1 Virtual Servers Choose menu “ Forwarding → Virtual Servers ”, and then you can view and add virtual servers in the screen as shown in Figure 5-27. Virtual servers can be u sed for setting up public services on your LAN, such as DNS, Email and FTP.
TL-WR702N 150Mbps Wireless N Nano Router - 79 - Figure 5-28 Add or Modify a Virtual Server Entry ) Note: If your computer or server has more than one ty pe of available service, please select another service, and enter the same IP Addr ess for that computer or server .
TL-WR702N 150Mbps Wireless N Nano Router - 80 - Figure 5-29 Port Triggering Once the Router is configured, the operation is as follows: 1. A local host makes an outgoing connection us ing a destination port number defined in t he T rigger Port field. 2.
TL-WR702N 150Mbps Wireless N Nano Router - 81 - 5. Select Enable in Statu s field. 6. Click the Save button to save the new rule. Figure 5-30 Add or Modify a Port T riggering Entry T o modify or delete an existing entry: 1. Click the Modify in the entry you wa nt to modify .
TL-WR702N 150Mbps Wireless N Nano Router - 82 - Figure 5-31 DMZ T o assign a computer or server to be a DMZ server: 1. Check the Enable radio button. 2. Enter the IP Address of a local host in the DMZ Host IP Address field. 3. Click the Save button. ) Note: After you set the DMZ host, the firewa ll related to the host will not work.
TL-WR702N 150Mbps Wireless N Nano Router - 83 - • Protocol - The type of protocol the Rout er opens for the application. • Internal Port - The Internal port the Router opens for local host. • IP Address - The IP address of the UPnP device t hat is currently accessing the Router.
TL-WR702N 150Mbps Wireless N Nano Router - 84 - ¾ Enable Firewall - the general firewall switch is on or of f. ¾ Enable IP Address Filtering - set IP Address Filtering is enabled or disabled. There are two default filtering rules of IP Address Filtering, either Allow or De ny passing through the router .
TL-WR702N 150Mbps Wireless N Nano Router - 85 - 1. Effective Time - Enter a range of time in HHMM forma t, which point to the range time for the entry to take ef fect.
TL-WR702N 150Mbps Wireless N Nano Router - 86 - 5.9.3 Domain Filtering The Domain Filtering page allows you to control access to certain websites on the Internet by specifying their domai ns or key words.
TL-WR702N 150Mbps Wireless N Nano Router - 87 - Click the Disabled All button to make all entries disabled. Click the Delete All button to delete all entries Click the Next button to go to the next page and the Previous button to return to the previ ous page.
TL-WR702N 150Mbps Wireless N Nano Router - 88 - Figure 5-40 Add or Modify a MAC Address Filtering entry T o add or modify a MAC Address Filter ing entry , follow these instructions: 1. Enter the appropriate MAC Address into the MAC Address field. The format of the MAC Address is XX-XX-XX-XX-XX-XX (X is any hexadecimal digit) .
TL-WR702N 150Mbps Wireless N Nano Router - 89 - 5.9.5 Remote Management Y ou can configure the Remote M anagement function on this page. This feature allows you to manage your Router from a remote location, via the Internet. Figure 5-41 Remote Management ¾ Web Management Port - W eb browser access normally uses the standard HTTP service port 80.
TL-WR702N 150Mbps Wireless N Nano Router - 90 - Figure 5-42 Advanced Security settings ¾ Packet s St a tistic interval (5 ~ 60) - The default value is 10. Se lect a value between 5 and 60 seconds in the pull-down list. The Packet s St atistic interval value indicates the time section of the packet s statistic.
TL-WR702N 150Mbps Wireless N Nano Router - 91 - ¾ Ignore Ping Packet from W AN Port - Enable or Disable ignore ping packet from W AN port. The default is disabled.
TL-WR702N 150Mbps Wireless N Nano Router - 92 - T o add st atic routing entries: 1. Click the Add New button. 2. Enter the following data: ¾ Destination IP Address - The Destination IP Address is the address of the network or host that you want to assign to a static route.
TL-WR702N 150Mbps Wireless N Nano Router - 93 - Figure 5-46 IP QoS ¾ Enable IP Q oS - Enable or disable the function of IP QoS. ¾ Choose BandWid th T ype - Select the network connection ty pe from the drop-down list. ¾ Bandwidth Apply - The bandwidth you get.
TL-WR702N 150Mbps Wireless N Nano Router - 94 - 4. IP address range for dif ferent entries coul d not have intersection with each other . 5. After the confi gurations, click the Save button for the change to t ake effect.
TL-WR702N 150Mbps Wireless N Nano Router - 95 - Figure 5-49 IP & MAC Bin ding Setting (Add & Modify) T o add IP & MAC Binding entries: 1. Click the Add New .. button. 2. Enter the MAC Address and IP Address. 3. Select the Bind checkbox. 4.
TL-WR702N 150Mbps Wireless N Nano Router - 96 - Click the Delete All button to delete all entries. 5.12.2 ARP List T o manage the computer , you could observe the computers in the LAN by checking the relationship of MAC address and IP address on the ARP list, a nd you could configure the items on the ARP list also.
TL-WR702N 150Mbps Wireless N Nano Router - 97 - sign up for DDNS service providers s uch as www .dyndns.or g, www .oray .net or www .comexe.cn. The Dynamic DNS client service provi der will give you a password or key . 5.13.1 Ora y.net DDNS If your selected dynamic DNS Service Provider is www .
TL-WR702N 150Mbps Wireless N Nano Router - 98 - 5.14 System T ools Figure 5-53 The System T ools menu There are nine submenus under the System T ools menu: Tim e , Diagnostic , Firm w are , Factor y Default s, Backup and Restore, Reb oot, Password, Log and S tatistics.
TL-WR702N 150Mbps Wireless N Nano Router - 99 - T o set time manually , follow the steps below: 1. Select your local time zone. 2. Enter the Date in Month/Day/Y ear format. 3. Enter the Ti me in Hour/Minute/Second format. 4. Click Save . For automatic time synchronization: 1.
TL-WR702N 150Mbps Wireless N Nano Router - 100 - Figure 5-55 Diagnostic T ools ¾ Diagnostic T ool - Check the radio button to select one diagnostic too. • Ping - This diagnostic tool troubleshoots connectivity , reachabilit y , and name resolution to a given host or gateway .
TL-WR702N 150Mbps Wireless N Nano Router - 101 - ¾ T racerout e Max TTL - The max number of hop s for a T raceroute connection. Click St a rt to check the connectivity of the Internet. The Diagnostic Result s page displays the result of diagnosis. If the result is similar to the following screen, the connectivity of t he Internet is fine.
TL-WR702N 150Mbps Wireless N Nano Router - 102 - 2. Make sure that your computer is connect ed to the Internet through the cable when you upgrade the firmware. To upgrade through wirel ess connection is not allowed. 3. Set your IP address as static IP before upgrading.
TL-WR702N 150Mbps Wireless N Nano Router - 103 - Figure 5-59 Backup & Restore Configuration ¾ Click the Backup button to save all configuration setti ngs as a backup file in your local computer .
TL-WR702N 150Mbps Wireless N Nano Router - 104 - 5.14.7 Passw ord This page allows you to change the factory default user name and password of the router . Figure 5-61 Password It is recommended strongly that you change the factory default user name and password of the router .
TL-WR702N 150Mbps Wireless N Nano Router - 105 - Click the Refresh button to refresh the logs. Click the Clear All button to clear all the logs. 5.14.9 Statistics The S tatistics page displays the net work traf fic of each PC in LAN, including total traffic and traf fic of the last Packet s St atistic interval seconds.
TL-WR702N 150Mbps Wireless N Nano Router - 106 - UDP Tx The total amount of the UDP p ackets transmitted to W AN in the last Packet s Statistic interval seconds. TCP SYN Tx The total amount of the TCP SYN packets transmitted to W AN in the last Packet s St atistic interval seconds.
TL-WR702N 150Mbps Wireless N Nano Router - 107 - Chapter 6. Configuration for Repeater Mode This chapter will show each W eb page's key functions and the c onfiguration way for Repeater Mode of TL-WR702N. 6.1 Login After your successful login, you can configur e and manage the device.
TL-WR702N 150Mbps Wireless N Nano Router - 108 - Figure 6-2 S tatus ¾ Firmware V ersion - The version information of the Router ’s firmware. ¾ Hardware V ersion - The version information of the Router ’s hardware.
TL-WR702N 150Mbps Wireless N Nano Router - 109 - 6.4 Wo rking Mode The Router supports fi ve operation mode types: AP, Router , Repeater , Bridge and Client . Please select one your want. Click Save to save your choice, which is shown as Figure 4-3. Figure 6-3 W orking Mode ¾ AP - The wireless access point mode.
TL-WR702N 150Mbps Wireless N Nano Router - 1 10 - 6.5.1 LAN Choose menu “ Network → LAN ”, and then you can conf igure the IP parameters of th e LAN on the screen as below . Figure 6-6 LAN ¾ MAC Address - The physical address of the LAN ports , as seen from the LAN.
TL-WR702N 150Mbps Wireless N Nano Router - 1 1 1 - Figure 6-8 Wireless Setting s - Repeater ¾ SSID - The SSID of AP that you want to access. ¾ MAC of AP - The MAC address of AP that you want to access. ¾ Region - Select your region from the pull-down lis t.
TL-WR702N 150Mbps Wireless N Nano Router - 1 12 - z Near the center of the area in which your wireless stations will operate. z In an elevated location such as a high shelf. z Away from the potential sources of interfer ence, such as PCs, microwaves, and cordless phones.
TL-WR702N 150Mbps Wireless N Nano Router - 1 13 - Figure 6-10 DHCP Setting s ¾ DHCP Server - Enable or Disable the DHCP server . If you disable the Server , you must have another DHCP server within your network o r else you must configure the computer manually .
TL-WR702N 150Mbps Wireless N Nano Router - 1 14 - To use the DHCP server function of the Router, you must configure all computers on the LAN as "Obtain an IP Address automatically".
TL-WR702N 150Mbps Wireless N Nano Router - 1 15 - ¾ MAC Address - The MAC address of the PC for which you want to reserve an IP address. ¾ Reserved IP Address - The IP address reserved for the PC by the Router. ¾ Status - The status of this entry either Enabled or Disabled .
TL-WR702N 150Mbps Wireless N Nano Router - 1 16 - 6.8 System T ools Figure 6-14 T he System T ools menu Choose menu “ System T ools ”, and then you can see the submenus under the main menu: Diagnostic , Firm w are , Factory Default s, Backup & Restor e, Reboot, Password, and S ystem Log.
TL-WR702N 150Mbps Wireless N Nano Router - 1 17 - ¾ Diagnostic T ool - Check the radio button to select one diagnostic tool. • Ping - This diagnostic tool troubleshoots connectivity , reachabilit y , and name resolution to a given host or gateway .
TL-WR702N 150Mbps Wireless N Nano Router - 1 18 - Figure 6-17 Firmware Upgrade ¾ Firmware Version - This displays the current firmware version. ¾ Hardware Version - This displays the current hardware version. The hardware version of the upgrade file must accord with the R outer’s current hardware version.
TL-WR702N 150Mbps Wireless N Nano Router - 1 19 - Figure 6-18 Restore Factory Default Click the Restore button to reset all configuration settings to their default values. • The default User Name : admin • The default Password : admin • The default IP Address : 192.
TL-WR702N 150Mbps Wireless N Nano Router - 120 - 6.8.5 Reboot Choose menu “ System T ools → Reboot ”, and then you can click the Reboot button to reboot the Router via the next screen.
TL-WR702N 150Mbps Wireless N Nano Router - 121 - It is strongly recommended that you should change the factor y default user name and passwor d of the Router, because all users who try to access the Router's Web-based utility or Quick Setup will be prompted for the Router's default user name and password.
TL-WR702N 150Mbps Wireless N Nano Router - 122 - Chapter 7. Configuration for Bridge Mode This chapter will show each Web p age's key f unctions and the configurat ion way for Bridge Mode of TL-WR702N. 7.1 Login After your successful login, you can configur e and manage the device.
TL-WR702N 150Mbps Wireless N Nano Router - 123 - Figure 7-2 S tatus ¾ Firmware V ersion - The version information of the Router ’s firmware. ¾ Hardware V ersion - The version information of the Router ’s hardware.
TL-WR702N 150Mbps Wireless N Nano Router - 124 - • MAC address - The physical address of the Router , as seen from the WLAN. • WDS St atus - The status of WDS connection. ¾ Syst em Up Time - The length of the time since the Router was last power ed on or reset.
TL-WR702N 150Mbps Wireless N Nano Router - 125 - Figure 7-4 7.5 Network Figure 7-5 the Network menu There is only one submenu under the Network menu (shown in Figure 7-5): LAN . 7.5.1 LAN Choose menu “ Network → LAN ”, and then you can conf igure the IP parameters of th e LAN on the screen as below .
TL-WR702N 150Mbps Wireless N Nano Router - 126 - 7.6 Wireless Figure 7-7 Wireless menu There are two submenus under the Wireless menu (shown in Figure 7-7): Wireless Settings and Wireless Security . Click any of them, and you will be able to configure the corresponding function.
TL-WR702N 150Mbps Wireless N Nano Router - 127 - name (SSID) to a different value. This value is case-sensitive. For example, TEST is NOT the same as test . ¾ Region - Select your region from the pull-down lis t. This field specifies the region w here the wireless function of the Router can be used.
TL-WR702N 150Mbps Wireless N Nano Router - 128 - ¾ Authentication Type - This option should be c hosen if the key type is WEP (ASCII) or WEP (HEX). It indicates the authoriz ation type of the Root AP. ¾ Password - If the AP your Router is going to c onnect needs password, you need to fill the password in this blank.
TL-WR702N 150Mbps Wireless N Nano Router - 129 - Figure 7-9 Wireless Se curity ¾ Disable Security - The wireless security function can be enabled or disabled . If disabled, the wireless stations will be able to con nect the Ro uter without encryption.
TL-WR702N 150Mbps Wireless N Nano Router - 130 - • WEP Key (Password) - Select which of the four keys will be used and enter the matching WEP key that you create. Make sure these val ues are identical on all wireless stations in your network. • Key Type - You can select the WEP key length (64-bit, or 128-bit, or 152-bit.
TL-WR702N 150Mbps Wireless N Nano Router - 131 - For ASCII , the key can be made up of any numbe rs 0 to 9 and any letters A to Z, the length should be between 8 and 63 characters. For Hexadecimal , the key can be made up of any numbers 0 to 9 and letters A to F, the length should be between 8 and 64 characters.
TL-WR702N 150Mbps Wireless N Nano Router - 132 - Figure 7-1 1 DHCP Settings ¾ DHCP Server - Enable or Disable the DHCP server . If you disable the Server , you must have another DHCP server within your network o r else you must configure the computer manually .
TL-WR702N 150Mbps Wireless N Nano Router - 133 - ) Note: To use the DHCP server function of the Router, you must configure all computers on the LAN as "Obtain an IP Address automatically".
TL-WR702N 150Mbps Wireless N Nano Router - 134 - Figure 7-13 Address Reservation ¾ MAC Address - The MAC address of the PC for which you want to reserve an IP address. ¾ Reserved IP Address - The IP address reserved for the PC by the Router. ¾ Status - The status of this entry either Enabled or Disabled .
TL-WR702N 150Mbps Wireless N Nano Router - 135 - Click the Next button to go to the next page and Click the Previous button to return the previous page.
TL-WR702N 150Mbps Wireless N Nano Router - 136 - Figure 7-16 Diagnostic T ools ¾ Diagnostic T ool - Check the radio button to select one diagnostic tool. • Ping - This diagnostic tool troubles hoots connectivity , reachabilit y , and name resolution to a given host or gateway .
TL-WR702N 150Mbps Wireless N Nano Router - 137 - ¾ T racerout e Max TTL - The max number of hops for a Tr aceroute connection. The default is 20. Click St a rt to check the connectivity of the Internet. The Diagnostic Result s page displays the result of diagnosis.
TL-WR702N 150Mbps Wireless N Nano Router - 138 - 2. Type the path and file name of the update file into the File field, or click the Browse button to locate the update file. 3. Click the Upgrade button. ) Note: 1. New firmware vers ions are posted at http://www.
TL-WR702N 150Mbps Wireless N Nano Router - 139 - 7.8.4 Backup & Restore Choose menu “ System T ools → Backup & Restore ”, and then you can save the current configuration of the Rout er as a backup file and restore the configuration via a backup file as shown in Figure 7-20.
TL-WR702N 150Mbps Wireless N Nano Router - 140 - • Change the Wireless configurations. • Change the Web Management Port. • Upgrade the firmware of the Router (system will reboot automatically). • Restore the Router's settings to factory defaults (syste m will reboot automatically).
TL-WR702N 150Mbps Wireless N Nano Router - 141 - 7.8.7 System Log Choose menu “ System T ools → S ystem Log ”, and then you can view the logs of the Router. Figure 7-23 System Log ¾ Refresh - Refresh the page to show the latest log list. ¾ Clear All - All the logs will be deleted from the R outer permanently, not just from the page.
TL-WR702N 150Mbps Wireless N Nano Router - 142 - Chapter 8. Configuration for Client Mode This chapter will show each Web p age's key func tions and the configuratio n way for Client Mode of TL-WR702N. 8.1 Login After your successful login, you can configur e and manage the device.
TL-WR702N 150Mbps Wireless N Nano Router - 143 - Figure 8-2 S tatus ¾ Firmware V ersion - The version information of the Router ’s firmware. ¾ Hardware V ersion - The version information of the Router ’s hardware.
TL-WR702N 150Mbps Wireless N Nano Router - 144 - 8.4 Wo rking Mode The Router supports fi ve operation mode types: AP, Router , Repeater , Bridge and Client . Please select one your want. Click Save to save your choice, which is shown as Figure 8-3. Figure 8-3 W orking Mode ¾ AP - The wireless access point mode.
TL-WR702N 150Mbps Wireless N Nano Router - 145 - 8.5.1 LAN Choose menu “ Network → LAN ”, and then you can conf igure the IP parameters of th e LAN on the screen as below . Figure 8-6 LAN ¾ MAC Address - The physical address of the LAN ports , as seen from the LAN.
TL-WR702N 150Mbps Wireless N Nano Router - 146 - Figure 8-8 Wireless Setting s - Client ¾ SSID - Enter a string of up to 32 characters. The same name of SSID (Service Set Identification) must be assigned to all wireless devices in your network.
TL-WR702N 150Mbps Wireless N Nano Router - 147 - Be sure to click the Save button to save your settings on this page. ) Note: 1. The operating distance or range of your wire less connection varies significantly based on the physical placement of the Router .
TL-WR702N 150Mbps Wireless N Nano Router - 148 - Figure 8-10 DHCP Setting s ¾ DHCP Server - Enable or Disable the DHCP server . If you disable the Server , you must have another DHCP server within your network o r else you must configure the computer manually .
TL-WR702N 150Mbps Wireless N Nano Router - 149 - ) Note: To use the DHCP server function of the Router, you must configure all computers on the LAN as "Obtain an IP Address automatically".
TL-WR702N 150Mbps Wireless N Nano Router - 150 - Figure 8-12 Address Reservation ¾ MAC Address - The MAC address of the PC for which you want to reserve an IP address. ¾ Reserved IP Address - The IP address reserved for the PC by the Router. ¾ Status - The status of this entry either Enabled or Disabled .
TL-WR702N 150Mbps Wireless N Nano Router - 151 - Click the Next button to go to the next page and Click the Previous button to return the previous page.
TL-WR702N 150Mbps Wireless N Nano Router - 152 - Figure 8-15 Diagnostic T ools ¾ Diagnostic T ool - Check the radio button to select one diagnostic tool. • Ping - This diagnostic tool troubles hoots connectivity , reachabilit y , and name resolution to a given host or gateway .
TL-WR702N 150Mbps Wireless N Nano Router - 153 - ¾ T racerout e Max TTL - The max number of hops for a Tr aceroute connection. The default is 20. Click St a rt to check the connectivity of the Internet. The Diagnostic Result s page displays the result of diagnosis.
TL-WR702N 150Mbps Wireless N Nano Router - 154 - 2. Type the path and file name of the update file into the File field, or click the Browse button to locate the update file. 3. Click the Upgrade button. ) Note: 1. New firmware vers ions are posted at http://www.
TL-WR702N 150Mbps Wireless N Nano Router - 155 - 8.8.4 Backup & Restore Choose menu “ System T ools → Backup & Restore ”, and then you can save the current configuration of the Rout er as a backup file and restore the configuration via a backup file as shown in Figure 8-19.
TL-WR702N 150Mbps Wireless N Nano Router - 156 - • Change the Wireless configurations. • Change the Web Management Port. • Upgrade the firmware of the Router (system will reboot automatically). • Restore the Router's settings to factory defaults (syste m will reboot automatically).
TL-WR702N 150Mbps Wireless N Nano Router - 157 - 8.8.7 System Log Choose menu “ System T ools → S ystem Log ”, and then you can view the logs of the Router. Figure 8-22 System Log ¾ Refresh - Refresh the page to show the latest log list. ¾ Clear All - All the logs will be deleted from the R outer permanently, not just from the page.
TL-WR702N 150Mbps Wireless N Nano Router - 158 - Appendix A: FAQ 1. How do I configure the Router to access the Internet b y ADSL users? 1) First, configure the ADSL Modem configured in RFC1483 bridge model. 2) Connect the Ethernet cable from your AD SL Modem to the W AN port on the Router .
TL-WR702N 150Mbps Wireless N Nano Router - 159 - 2. How do I configure the Router to access the Internet b y Ethernet users? 1) Log in to th e Router , click the “ Netw ork ” menu on the left of your browser , and click " WA N " submenu.
TL-WR702N 150Mbps Wireless N Nano Router - 160 - Figure A-4 Virtual Serve rs Figure A-5 Add or Modify a Virtual server Entry ) Note: Your opposite side should call your WAN IP , which is displayed on the “Status” page.
TL-WR702N 150Mbps Wireless N Nano Router - 161 - 1) Because the WEB Server port 80 will inte rfere with the WEB management port 80 on the Router , you must change the WEB management port number to avoid interference.
TL-WR702N 150Mbps Wireless N Nano Router - 162 - Figure A-9 Add or Modify a Virtual server Entry 5. The wireless st ations cannot connect to the Router . 1) Make sure the " Enable Wireless Router Radio " is checked. 2) Make sure that the wireless stations' SSID accord with the Router's SSID.
TL-WR702N 150Mbps Wireless N Nano Router - 163 - Appendix B: Configuring the PC In this section, we’ll introduce how to inst all and configure the TCP/IP correctly in Windows XP . First make sure your Ethernet Adapter is work ing, refer to the adapter ’s manual if necessary .
TL-WR702N 150Mbps Wireless N Nano Router - 164 - Figure 0-2 5) The following TCP/IP Properties window will display and the I P Address tab is open on this window by default.
TL-WR702N 150Mbps Wireless N Nano Router - 165 - Figure 0-3 ) Note: For Windows 98 OS or before, the PC and Router may need to be restarted. ¾ Setting IP address manually 1 Select Use the following IP address radio button. And the fo llowing items available 2 If the Router's LAN IP addre ss is 192.
TL-WR702N 150Mbps Wireless N Nano Router - 166 - Now: Click OK to keep your settings..
TL-WR702N 150Mbps Wireless N Nano Router - 167 - Appendix C: Specifications General S tandards IEEE 802.1 1n, 802.1 1b, 802.1 1g Protocols TCP/IP , PPPoE, DHCP , ICMP , NA T , SNTP Port One 10/100Mbps.
TL-WR702N 150Mbps Wireless N Nano Router - 168 - Appendix D: Glossary ¾ 802.11n - 802.11n builds upon previous 802.11 standards by adding MIMO (multiple-input multiple-output).
TL-WR702N 150Mbps Wireless N Nano Router - 169 - ¾ PPPoE ( P oint to P oint P rotocol o ver E thernet) - PPPoE is a protocol for connecting remote hosts to the Internet over an always-on connection by simulating a dial-up connection.
Ein wichtiger Punkt beim Kauf des Geräts TP-Link TL-WR702N (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie TP-Link TL-WR702N noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für TP-Link TL-WR702N - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von TP-Link TL-WR702N reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über TP-Link TL-WR702N erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon TP-Link TL-WR702N besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von TP-Link TL-WR702N verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit TP-Link TL-WR702N. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei TP-Link TL-WR702N gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
