Benutzeranleitung / Produktwartung TD-W8951NB des Produzenten TP-Link
Zur Seite of 94
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) Rev: 3.0.0 1910010747.
COPYRIGHT & TRADEMARKS Specifications are subjec t to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., L TD. Other brands and product names are trademarks or registered trademarks of t heir respective holders.
FCC STATEMENT This equipment has been tested and found to comply wi th the limits for a Class B digital device, pursuant to part 15 of the FCC Ru les. These limits are designed to pr ovide reasonable protectio n against harmful interference in a residential installation.
CE Mark Warning This is a Class B product. In a domestic environm ent, this product may cause radio interference, in which case the user may be required to take adequate measures. This device has been designed to operate with the antennas listed below , and havin g a maximum gain of 5dBi.
NCC Notice: 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、 加大功 率或變更原設計之特性及功能。 低功率射.
TP-LINK TECHNOLOGIES CO., L TD TP-LINK TECHNOLOGIES CO., LTD. Building 24 (floors 1, 3, 4, 5), and 28 (floors 1-4) Central Science and Technology Park, Shennan Rd, Nanshan, Shenzhen, China DECLARA TION OF CONFORMITY For the following equipment: Product Description: 150Mbps Wireless N ADSL2+ Modem Router (Annex B) Model No.
CONTENTS Package Cont ents .................................................................................................... 1 Chapter 1. Introducti on ......................................................................................... 2 1.1 Product Over view .
4.5.4 UPnP ....................................................................................................................... 64 4.5.5 DDNS ..........................................................................................................
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 1 Package Contents The following contents should be found in your package: ¾ One TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Rout.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 2 Chapter 1. Introduction Thank you for choosing the TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) . 1.1 Product Overview The device is designed to provide a simple and cost-effective ADSL Internet connection for a private Ethernet or IEEE 802.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 3 ¾ Downstream data rates up to 24Mbps, upstream data rates up to 3.5Mbps （ With Annex M enabled ） . ¾ Supports long transfers, the max line length can reach to 6.5Km. ¾ Supports remote configurati on and management through SNMP and CWMP.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 4 Chapter 2. Hardware Installation 2.1 The Front Panel Figure 2-1 The LEDs locate on the front panel. They indicate the device’s working st atus. For details, please refer to LED Explanation.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 5 ) Note: 1. If the ADSL LED is off, please check your Internet connection first. Refer to 2.4 Connecting the Modem Router for more information about how to ma ke Internet connection correctly.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 6 least 5 seconds. And the Router will reboot to its factory default settings. Method two : Restore the default setting from “Mai ntenance-SysRestart” of the Router's Web-based Utility.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 7 Figure 2-3 W all-mount Install ) Note: The diameter of the screw, 3.5mm<D<7.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 8 • PHONE: Connect to the phone sets • MODEM: Connect to the ADSL port of TD-W8951NB Plug one end of the twisted-pair ADSL cable into the ADSL port on the rear panel of TD-W8951NB.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 9 Chapter 3. Quick Installation Guide 3.1 Configure PC After you directly connect your PC to the TD-W8951NB or connect your adapter to a Hub/Switch which has connected to the Router, you need to conf igure your PC’s IP address.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 10 Figure 3-2 Step 3: Select General tab, highlight Internet Protoc ol (TCP/IP), and then click the Properties button.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 11 Step 4: Configur e the IP address as Figure 3-4 shows. After that, click OK .
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 12 Figure 3-5 If the result displayed is similar to the screen shown belo w, it means t hat your PC has not connected to the Router.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 13 Figure 3-7 Step 1: Select the Quick Start tab, then click RUN WIZARD , and you will see the next screen. Click the NEXT button. Figure 3-8 Step 2: Configur e the time for the Router, and then click the NEXT button.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 14 Figure 3-10 Step 4: Configur e the following options provided by your ISP: Username , Password , VPI , VCI and Connection Type . Then click NEXT . Figure 3-1 1 Step 5: Configur e the rules for the WLAN, and click NEXT .
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 15 Figure 3-12 ) Note: If the Access Point is activated, the wireless f unction will be available even without the external antenna because of an additional prin ted antenna. To adopt the wi reless security protection measures, please refer to 4.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 16 Chapter 4. Software Configuration This User Guide recommends using the “Quick Installation Guide” for first-time installation.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 17 Figure 4-2 ) Note: Click the other submenus Sy stem Log or Statistics in Figure 4-2 , and you will be able to view the system log and traffic statistics about the Router.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 18 Figure 4-3 The Router can keep logs of all traffic. Yo u can query the logs to find what happened to the Router. Click the CLEAR LOG button to clear the logs. Click the SAVE LOG button to save the logs.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 19 Figure 4-4 ¾ Interface: You can select Ethernet , ADSL and WLAN to view the corresponding network traffic over different ports. ¾ Select Ethernet , and you will see the statistics table as below.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 20 ¾ Select ADSL , and you will see the statistics table as below. Statistics Table: Transmit total PDUs The total PDUs transmitted over the ADSL port. Transmit Statistics Transmit total Error Counts The total errors occurred ov er the ADSL port when dat a is being transmitted.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 21 4.3 Interface Setup Choose “ Interface Setup ”, you can see the next submenus: Internet , LAN and Wireless . Figure 4-5 Click any of them, and you will be able to configure the corre sponding function.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 22 Figure 4-6 ¾ ATM VC: ATM settings are used to connect to your ISP. Your ISP provides VPI (Vir tual Path Identifier), VCI (Virtual Channel Identif ier) settings to you.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 23 • Virtual Circuit: Select the VC number you want to setup, PVC0~PVC7. • Status: If you want to use a designed VC, you should activate it. • VPI: Identifies the virtual path between endpoints in an ATM network.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 24 ¾ Encapsulation: Select the encapsulation mode for the Dy namic IP Address, you can leave it default. ¾ NAT: Select this option to Enabl e/Disable the NAT (Network Address Translation) function for this VC.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 25 Figure 4-8 ) Note: Each IP address entered in the fields must be in t he appropriate IP form, which is four IP octets separated by a dot (x.x.x.x), such as 192.168.1.100. The Router will not acce pt the IP address if it is not in this format.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 26 Figure 4-9 ¾ Servicename: Enter a name to mark current conne ction, or you can leave it blank. ¾ Username: Enter your username for your PPPoA/PPPoE connection. ¾ Password: Enter your password for your PPPoA/PPPoE connection.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 27 automatically. And once there is traffic send or receive, the connection will be automatically on. ¾ Static/Dynamic IP Address: For PPPoA/PPPoE connection, you need to specify the public IP address for this ADSL Router.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 28 Figure 4-1 1 ¾ Router Local IP: These are the IP settings of the LAN interface for the device. These settings may be referred to as Private settings. You may change the LAN IP address if needed.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 29 • Multicast: Select IGMP version, or disable the function. IGMP (Internet Group Multicast Protocol) is a session-layer prot ocol used to establish member ship in a multicast group.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 30 be able to obtain IP address automatically al thou gh the DHCP function is enabled. All the ports are checked by default. ¾ DHCP Table : The information of the DHCP clients will be displayed here • Hostname: Display the name of the DHCP client.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 31 Figure 4-13 • DHCP Server IP for Relay Agent: Enter the DHCP server IP Address runs on WAN side. ) Note: If you select Disabled , the DHCP function will not take ef fect. 4.3.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 32 Figure 4-14.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 33 ¾ Access point Settings: These are the settings of the ac cess point. You c an configure the rules to allow wireless-equipped computers and other devices to communicate with a wireless network.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 34 ¾ 11n Settings: These are the settings of the 11n par ameters. If “802.11n”, “802.11g+n” or “802.11b+g+n” is selected for Wireless mode , these settings will be displayed.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 35 1) WEP-64Bits To configure WEP-64Bits settings, select the WEP-64Bits option from the drop-down list. The menu will change to offer the appropriate settings . WEP-64Bits is a data privacy mechanism based on a 64-bit shared key algorithm, as described in the IEEE 802.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 36 Figure 4-18 ¾ Encryption: Select the encryption you want to use: TKIP/AES, TKIP or AES (AE S is an encryption method str onger than TKIP).
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 37 Figure 4-20 4.3.3.1 WPS Settings ¾ WPS Settings: WPS can help you to add a new wireless device to an existing network quickly. This section will gui de you how to use WPS function.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 38 Step 2: Press and hold the WPS button of the adapt er directly for 2 or 3 seconds. Step 3: Wait for a while until the next screen appears. Click Finish to complete the WPS configuration.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 39 The WPS Configuration Screen of Wireless Adapter Step 3: Wait for a while until the next screen appears.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 40 2) PIN code If the wireless adapter supports Wi -Fi Protected Setup and the PIN method, you can add it to the network by PIN with t he following two methods. Click PIN code , you will see the screen as shown below.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 41 Figure 4-23 Method Two: Enter the PIN from my Router Step 1: Get the Current PIN code of the Router from AP self PIN code in Figure 4-23 (each Router has its unique PIN code. Here takes the PIN code 00001557 of this Router for example).
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 42 is the same for all stations in your wireless network. Type the desired SSID in the space provided. • Authentication Type: Select an authentication type fr om the drop-down list, which allows you to configure security features of the wireless LAN interface.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 43 Figure 4-25 ¾ Firewall: Select this option can aut omatically detect and block Denial of Service (DoS) attacks, such as Ping of Death, SYN Flood, Port Scan and Land Attack.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 44 ¾ Destination IP Address: This parameter specifies the IP network address of the final destination. ¾ IP Subnet Mask: Enter the subnet mask for this destination. ¾ Gateway IP Address: Enter the IP address of the gatew ay.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 45 ¾ NAT Status: This field shows the current status of the NAT function for the current VC. You can go to the previous screen (shown in Figure 4-6 ) to activate the function. ¾ Number of IPs; This field is to specify how many IPs are provided by your ISP for current VC.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 46 Figure 4-30 ¾ Rule Index: The Virtual server rule index for this VC. You can specify 10 rules in maximum. All the VCs with single IP will use the same Virtual Server rules. ¾ Application: The Virtual servers can be used for se tting up public services on your LAN.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 47 Click the BACK button to return to the previous screen. Click the CANCEL button to cancel the configur ation which is made just now.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 48 Step 3: Select the rule type you w ant from the drop-down list. Step 4: Enter the local and public IP addresses in the corresponding fields. Step 5: After that, click SAVE to make the entry take effect.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 49 Figure 4-32 ¾ QoS: Select this option to Activa te/Deactivate the IP QoS on different types (IP ToS and DiffServ). ¾ Summary: Click the button to view t he configurations of QoS.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 50 • Application: Select the application t hat the rule aimed at. • Physical Po rts: Select the port whose traffic fl ow a re controlled by the rule. • Destination MAC & IP & Mask & Port Range: Enter the IP information about the Destination host for the rule.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 51 4.4.5 VLAN Choose “ Advanced Setup → VLAN ”, you can activate the VLAN function in the next screen.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 52 Figure 4-34 ¾ PVID: Each physical port has a default VID ca lled PVID (Port VID). PVID is assigned to untagged frames or priority tagged frames (frame s with null (0) VID) received on this port.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 53 Figure 4-35 ¾ VLAN Index: Select the VLAN index for this VC. You can specify 8 gr oups in maximum.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 54 Figure 4-36 ¾ ADSL Mode: Select the ADSL operation mode wh ich your ADSL connection uses.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 55 Figure 4-38 ¾ ACL: If Activated , the IP addresses which are contai ned in the Access Control List can access to the Router. If Deactivated , all IP addresses can access to the Router.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 56 4.5.2.1 IP Filter Select IP /MAC Filter as the Filter type, and select IP as the Rule type (shown in Figure 4-39 ), then you can configure the filt er rules based on IP address.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 57 ) Note: If select PVC0~PVC7 as an interface, the filter will match the IP traffic of WAN port with specified IPs (Source IP Address and Destination IP Address). If select LAN as an inte rface, the filter will match the IP traffic of LA N port with specified IPs.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 58 as follows. Presume the rules ar e both aimed at the interface PVC 0, and their ind exes are (1, 1), (1, 2) and (1, 3). Step 1: Select the “IP/MAC Filter” as t he Filter Type Selection (show in Figure 4- 39 ).
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 59 Step 6: Go to Step 2 to configure the next two rule s: Block E-mail received by the IP addres s 192.168.1.7 on your local network; Make t he PC with IP address 192.168.1.8 una ble to visit the website of IP address 202.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 60 Figure 4-40 ¾ Rule Type: Select MAC for the MAC Filter rule. ¾ Active: Select “Yes” to make t he rule to take effect.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 61 Select the “MAC” as the Rule Ty pe on the Filter screen (show in Figure 4 -40 ).
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 62 4.5.2.3 Application Filter Select Application Filter as the Filter type (shown in Figure 4-41 ), and then you c an configure the filter rules based on application. Figure 4-41 ¾ Filter Type Selection: Select the Application Filter for the next configuration.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 63 Figure 4-42 ¾ Filter Type Selection: Select the URL Filter fo r the next configuration. ¾ Active: Select “Yes” to make t he rule to take effect. ¾ URL Index: Select the index for the URL Filter entry.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 64 Other operations for the entries as show n in Figure 4-39 : Select the URL Index to view or modify the entry. Select the URL Index to locate the specific rule, and then click the DELETE button to delete the entry.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 65 Figure 4-44 ¾ UPnP: Activate or Deactivate the UPnP function. Only when the function is activa ted, can the UPnP take effect.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 66 ¾ Service Provider: This field displays the service provider of DDNS. ¾ My Host Name: Enter your host name here. ¾ E-mail Address: Enter your E-mail address here. ¾ Username & Password: Type the “User Name” and “Password” for your D DNS account.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 67 ¾ User Name/Passwo rd: Enter the User Name and Password that provided the ACS server to login the router. ¾ Periodic Inform: Activate or deactivate the function. If Activat ed, the information will be informed to ACS server periodically.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 68 4.6.2 Time Zone Choose “ Maintenance → Time Zone ”, you can configure the system time in the screen (shown in Figure 4-49 ). The system time is the time used by the device for scheduling services.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 69 Figure 4-50 3) Manually Select Manually as the Synchronize time, you need to se t the date and time corresponding to the current time.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 70 Figure 4-52 To upgrade the router's firmware, follow these instructions below: Step 1: Type the path and file name of t he update file into the “New Firmware Location” field.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 71 Figure 4-53 Step 2: Save the file as the appointed file (shown in Figure 4-54 ). TD-W8951NB Figure 4-54 To restore the Router’s settings: Step 1: Click the Browse button to locate the update file for the device, or enter the exact path in “New Romfile Location” field.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 72 4.6.4 SysRestart Choose “ Maintenance → SysR esta rt ”, you can select to restart t he device with current settings or restore to factory default settings in the screen (shown in Figure 4-55 ).
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 73 Figure 4-56 4.7 Help Choose “ Help ”, you can view the help information for configuration of any function.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 74 Figure 4-57 ) Note: Click the tab, and you will be able to get the corresponding information.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 75 Appendix A: Specifications General Standards and Protocols ANSI T1.413, ITU G.992.1, ITU G. 992.2, ITU G.992.3, ITU G.992.5, IEEE 802.11b, IEEE 802.11g, I EEE 802.11n, IEEE 802.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 76 Appendix B: Troubleshooting T1. How do I restore m y Modem Router’s configuration to its fact ory default settings? With the Modem Router powered on, press and ho ld the RESET button on the rear panel for 8 to 10 seconds before releasing it.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 77 Click Change adapter settings Click Properties Right-click Local Area Connection.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 78 Double-click Internet Protocol Version 4 (TCP/IPv4) Select Obtain an IP address automatically Select Obtain DNS server address.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 79 For Windows Vista OS Go to Start > Settings > Control Panel , and then you will see the following page.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 80 Double-click Internet Protocol Version 4 (TCP/IPv4) Select Obtain an IP address automatically Select Obtain DNS server address.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 81 For Windows XP OS Go to Start > Control Panel , you will then see the following page.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 82 Double-click Internet Protocol (TCP/IP) Select Obtain DNS server address automatically Select Obtain an IP address automatical.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 83 Click OK.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 84 2) Configure your IE browser Open your IE browser, click Tools tab and you will see the following screen.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 85 2) Check to see if you can lo g on to the web managem ent page of the M odem Router. If you can, try the following steps. If you cannot, please set your computer referring to T3 then try to see if you can access the Internet.
TD-W8951NB 150Mbps Wireless N ADSL2+ Modem Router (Annex B) User Guide 86 Appendix C: Technical Support Technical Support For more troubleshooting help, go to: http://www.tp-link.com/e n/support/faq T o download the latest Firm ware, Driver , Utility and User Guide, go to: http://www.
Ein wichtiger Punkt beim Kauf des Geräts TP-Link TD-W8951NB (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie TP-Link TD-W8951NB noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für TP-Link TD-W8951NB - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von TP-Link TD-W8951NB reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über TP-Link TD-W8951NB erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon TP-Link TD-W8951NB besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von TP-Link TD-W8951NB verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit TP-Link TD-W8951NB. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei TP-Link TD-W8951NB gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
