Benutzeranleitung / Produktwartung toshiba satellite user's manual des Produzenten Toshiba
Zur Seite of 214
T OSHIBA Satellite L550/ Satellite Pro L550/ Satellite L550D/ Satellite Pro L550D series User's Manual.
User ’s Manual ii Copyright © 2009 by TOSHIBA Corporation. All rights reserved. Under the copyright laws, this manual cannot be reproduced in any form without the prior written permission of TOSHIBA. No p at ent liabili ty is assumed, with respect to the use of the information contained herein.
User ’s Manual iii ConfigFree is a trade mark of TOSHIBA Corporation. DVD MovieFactory is trademark of the Corel Corporations. Manufactured under licens e from Dolby Lab oratories. ExpressCard is a trademark of PCMCIA HDMI, the HDMI logo and High-Definition Multimedia Interfa ce are trademarks or registered trade marks of HDMI Lice nsing LLC.
User ’s Manual iv FCC conditions This device complies with part 15 of the FCC Rules. Operation is subj ect to the following two conditions: 1. This device may not cause harmful interfere nce. 2. This device must accept any interference received, including interference that may cause undesired opera tion.
User ’s Manual v EU Conformity S t atement VCCI Class B Information Canadian regulatory in formatio n (Canada only) This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the Radio Interference Regulation of the Canadian Department of Communications.
User ’s Manual vi Modem warning notice Conformity S tatem ent The equipment has been approved to [Commission Decision “CTR21”] for pan-European single te rminal connectio n to the Public Sw itched T elephone Network (PSTN).
User ’s Manual vii Redial Up to two redial atte mpts can be made. If more th an two redial attempts are made, the modem will return Black Listed . If you are experiencing problems with the Black Listed code, set the interval between redials at one minute or longer .
User ’s Manual viii Pursuant to FCC CFR 47, Part 68: When you are ready to install or use the modem, call your local telephone company and give them the following information: ■ The telephone number of the line to which you will connect the modem ■ The registration number t hat is located on the device.
User ’s Manual ix T ype of service Y our modem is desi gned to be used on standard-device telephon e lines. Connection to telep hone company-provided coin se rvice (central office implemented systems) is pr ohibited. Connection to pa rty lines service is subject to state tarif fs.
User ’s Manual x Instructions for IC CS -03 certified equipment 1. The Industry Canada label identi fies certified e quipment. This certification means that the equipment meets certain telecommunica.
User ’s Manual xi Notes for Users in Australia and New Zealand Modem w arning notice for Australia Modems connected to the Australian te lecoms network must have a valid Austel permit. This modem has been desi gned to specifically configure to ensure compliance with Austel standards when the country/region selection is set to Australia.
User ’s Manual xii ■ Some parameters required fo r compliance with T eleco m’s P TC S pecifications are dep endent on th e equipment (PC) associated with this modem.
User ’s Manual xiii ■ The transmit level from this device is set at a fixe d level and because o f this there may be circumstances where the performance is less than optimal.
User ’s Manual xiv Following information is only for EU-memb er states: Disposal of products Disposal of batteries and/or accumulators The crossed out wheeled dust bin symbol in dicates that products must be collected and disp osed of separately from household waste .
User ’s Manual xv ENERGY ST AR ® Program Disposing of the com puter and the computer’s batte r ies ■ Discard this compu ter in acco rdance with appli cable laws and regulations. For further information, cont act y our local government. ■ This computer contains rechargeable batteries.
User ’s Manual xvi Optical disc drive st andards TOSHIBA Satellite L550/Satellite Pro L550/Satellite L550D/Satel lite Pro L550D series computer is shipped with one of the following drives preinstalled: DVD Super Multi (+-R DL) drive or DVD Super Multi (+-R DL) /w Label Flash d rive.
User ’s Manual xvii DVD Super Multi (+-R DL) drive Panasonic UJ 880AD/UJ880ED HLDS G T20N/G T20F Pioneer DVR-TD09TBM/DVR-TD09TBF Location of the required label COMPLIES WITH FDA RADIA TION PERFORMANCE ST ANDARDS, 21 CFR SUBCHAPTER J. MANUF ACTURED Panasonic Communications Co.
User ’s Manual xviii T oshiba Samsung TS-L633C/TS-L633 Y Location of the required label COMPLIES WITHFDA RADIA TION PERFORMANCE ST ANDARDS, 21 CFR SUBCHAPTER J MANUF ACTURED PIONEER CORPORA TION 4-1.
User ’s Manual xix International precautions CAUTION: This appliance contains a laser system and is classified as a “CLASS 1 LASER PRODUCT .” T o use this model properly , read the instruction manual carefully a nd keep this manual for your future reference.
User ’s Manual xx OBS! Apparaten innehåller laserkomponent som avger laserstråini ng överstigande gränsen för laserkl ass 1. V AROITUS. Suojakoteloa si saa avata. Laite sisältää laserdiodin, joka lähetää näkymätöntä silmilie vaaral lista lasersäteilyä.
User ’s Manual xxi T able of Content s Copyright. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
User ’s Manual xxii TOSHIBA V alue Added Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-12 Utilities and Applicati ons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-12 Options . . . . . . . . . . . . . . . .
User ’s Manual xxiii Generating ASCII characters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5 Chapter 6 Power and Power-up Modes Power conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
User ’s Manual xxiv Appendix A S pecifications Environment a l requirement s . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1 Appendix B Display Controller Display contro ller . . . . . . . . . . . . . . . . . . . . . . . . . . . .
User ’s Manual xxv Preface Congratulations on your purchase of the TOSHIBA Satellite L550/Satellite Pro L550/Satellite L550D/Satelli te Pro L550D series computer . This powerful notebook computer provides excellent expansion capability , includes multimedia functionality , and is designed to provide years of reliable, high-performan ce computing.
User ’s Manual xxvi Preface Chapter 4, Operating Basics , includes tips on care of the computer and on using the touchpad, optical disc drive, Aud io/Video controls, the web camera, the micropho ne, the internal mode m, wireless co mmunication and LAN.
User ’s Manual xxvii Preface Display Messages Messages are used in this manual to bring important information to your attention. Each type of message is identified a s shown below .
User ’s Manual xxviii General Precautions TOSHIBA computers are designed to optimize safety , minimize strain and withstand the rigors of portability . Ho we ver , certain precautions should be observed to further reduce the risk of personal injury or damag e to the computer .
User ’s Manual xxix General Precautions T o keep your comp uter in prime ope rati ng cond ition, protect your work area from: ■ Dust, moisture, and direct sunlig ht. ■ Equipment that generate s a strong electromagnetic field, such as stereo speakers (other tha n speak ers that are connected to the computer) or speakerphones.
User ’s Manual xxx General Precautions Mobile phones Please be aware that the use of mob ile phones can inte rfere with the aud io system. The operation of the computer wil l not be impa ired in any way , but it is recommended that a minimum distance of 30cm is maintained between the computer and a mobile phone that is in use.
User ’s Manual 1-1 Chapter 1 Introduction This chapter provides an equipment checkli st, and it identifies the computer ’s features, options and accessories. Equipment checklist Carefully unpack your comp uter , taking care to save the b ox and packaging materials for future use.
User ’s Manual 1-2 Introduction Sof twar e The following Wi ndows ® operating system and ut ility sof tware are pre-installed. ■ Microsoft ® Windows V ista ® ■ Modem Driver (Can be used only .
User ’s Manual 1-3 Introduction Features This computer incorporates the following fea tures and benefits: Processor Chipset Mobile Intel ® PM45 Express Chipset Mobile Intel ® GM45 Express Chipset .
User ’s Manual 1-4 Introduction Vi deo RAM Video RAM depends on the model you purchased. Mobile Intel ® GM45 Express Chipset model/ Mobile Intel ® GL40 Express Chi pset model: Video RAM capacity shares with main memory , and the proportio n depends on Dynamic Video Memory T echnology .
User ’s Manual 1-5 Introduction Disks Hard disk dr ive or Solid State drive This computer is equipped with the following types of Solid S tate Drive(SSD) and Hard Disk Drive (HDD).
User ’s Manual 1-6 Introduction Optical disc drive DVD Super Multi drive The drive reads DVD-ROM's at a maximum 8x speed and CD-ROM's at a maximum 24x speed, and writes CD-R's at u p .
User ’s Manual 1-7 Introduction Keyboard Pointing Device Power Ports Built-in The internal keyboard provides dedicated cursor control overlay keys, and Keys. The keyboard is compatible with the IBM ® enhanced keyboard. Refer to Chapter 5, The Keyboard , for details.
User ’s Manual 1-8 Introduction Slots Multimedia ExpressCard ™ The internal ExpressCar d slot is a Universal slot. This slot supports ExpressCard/54 an d ExpressCard/34 modules. Bridge media This slot lets you insert an SD ™ /SDHC ™ memory card, miniSD ™ /microSD ™ Card, Memory S t ick ® (PRO ™ ) and MultiMediaCard ™ .
User ’s Manual 1-9 Introduction Communications Modem Some models are equi pped with the integrated modem. The integrated modem provides capability for data and fax communications that support the V .90 (V .92) standards and includes a modem jack for connection to the telephone line.
User ’s Manual 1-10 Introduction Security Software The computer's internal display panel suppo rts high-resolution video graphics and can be set to a wide range of viewing angle s for maximum comfort and readability .
User ’s Manual 1-1 1 Introduction System automatic Sleep/Hibernati on Mode * This feature automatically shuts down the system into either Sleep Mode or Hi bernation Mode when there is no input or hardware access for a specified time. T his can be specified in the Power Options.
User ’s Manual 1-12 Introduction T OSHIBA V alue Added Package This section describes the TOSHIBA Component features pre-installed on the computer . Utilities and Applications This section describes the pre-installed uti lities that come with the computer and details how to start them.
User ’s Manual 1-13 Introduction Bluetooth St ack for Wind ows by T oshiba This software enables communication between the computer and external Blueto oth devices such as printers and mobile phones. Bluetooth functions cannot be used in models th at do not have a Bluetooth module in stalled.
User ’s Manual 1-14 Introduction TOSHIBA DVD-RAM Utility This utility has the functi on of Physical Fo rmat and Write-Protect to DVD-RAM. This utility is contained the setup module of TOSHIBA Disc Creator . T o start this utility , click Start → All Programs → TO SH I B A → CD&DVD Applications → DVD-RAM Utility .
User ’s Manual 1-15 Introduction Window s Mobility Center This section describes the Windows Mobility Center . Mobility Center is a utility for accessing several mobile PC settings quickly in one window . A default maxi mum of eight tiles are provided by the ope rating system, and the additional two tiles are added to your Mobility Center .
User ’s Manual 1-16 Introduction Options Y ou can add a number of options to make your computer even more powerful and con venient to use. The foll owing options are available: Memory expan sion 1,024MB/2 ,048MB/4,096MB memory modu le (PC2-6400) can easily be installed in the computer .
User ’s Manual 2-1 Chapter 2 The Grand T our This chapter identifies the vari ous components of your computer . Become familiar with each component before yo u operate the computer . Front with the display closed The following figure shows the computer ’s front with its display panel in the closed position.
User ’s Manual 2-2 The Grand T our Lef t side The following figure shows the comp uter's left side. Figure 2-2 The left side of the computer Keep foreign metal objects, such as scr ews, staples and paper clips, out of the Bridge media slot.
User ’s Manual 2-3 The Grand T our ■ Do not connect any cable other than a LAN cabl e to the LAN jack. It could cause damage or malfunction. ■ Do not connect the LAN cable to a power supply . It could cause damage or malfunction. HDMI out port HDMI out port can connect with T ype A connector HDMI cable.
User ’s Manual 2-4 The Grand T our Right side The following figure shows the comp uter ’s right side. Figure 2-3 The right side of the computer 1 3 5 2 4 1. Optical disc drive 2. Universal Serial Bus (USB 2.0) port *3. Modem jack 4. DC IN 19V jack 5.
User ’s Manual 2-5 The Grand T our Underside The following figure shows the undersi de of the computer . Y ou should ensure that the disp lay is closed befo re the computer is turned over to avoid causing any damage.
User ’s Manual 2-6 The Grand T our Battery safety lo ck Slide this latch into its 'Unlock' posi tion in order to release the battery pack and prepare for removal. Battery pack The battery pack provides power to the computer when the AC adapto r is not connected.
User ’s Manual 2-7 The Grand T our Front with the display op en This section shows the computer with the display panel open. In order to open the display , lift the display panel up and position it at a comfortable viewing angle for you. Figure 2-5 The front of the computer with the display open 1 2 3 3 4 5 7 6 8 9 10 12 11 1.
User ’s Manual 2-8 The Grand T our Display screen Please be a ware that, when the computer is operating on the AC adaptor , the image displayed on the internal screen will be somewhat brighter t han when it operates on battery power . This difference in brightness levels is intended to save power when opera ting on batteries.
User ’s Manual 2-9 The Grand T our Microphone A built-in microphone allows you to import and record sounds for your application - please refe r to the Sound system section in Chapte r 4, Operating Basics for more information. Some models are equipped with a micro phone.
User ’s Manual 2-10 The Grand T our Function buttons Some models provide four buttons nex t to the power button: Play/Pause, Previous, Next, Mute. Figure 2-6 Front operation panel These buttons allow you to manage a udio/video, run applications and access utilities.
User ’s Manual 2-1 1 The Grand T our System indicators The LED system indicators for specif ic computer operations glow when those operations are in progress. Figure 2-7 System indicators DC IN The DC IN indicator norma lly glows green when power is being correctly supplied from the AC power adaptor .
User ’s Manual 2-12 The Grand T our Keyboard indicators The following figures show the position s of the CAPS LOCK indicator and the NUM LOCK indicator . Figure 2-8 Keypad indicators CAPS LOCK This indicator glows green when lette r keys are locked into their uppercase format.
User ’s Manual 2-13 The Grand T our Optical disc drives The computer is configured with a DV D Super Multi drive. A Serial A T A interface controller is used for 12 cm (4.72") and 8cm (3.15") CD/DVD operation. When the computer is acce ssing a CD/DVD, an indicato r on the drive glows.
User ’s Manual 2-14 The Grand T our DVDs ■ DVD-R, DVD+R, DVD-R (Dual Layer) and DVD+R (Double Layer) discs can be written o nly once. The recorded data cannot be erased or changed. ■ DVD-RW , DVD+RW and DVD-RAM discs can be recorded more than once.
User ’s Manual 2-15 The Grand T our AC adaptor The AC adaptor can automat ically adjust to any voltage rang ing from 90 to 264 volts and to a freque ncy of either 47 o r 63 hertz, enablin g you to use this computer in almost any countr y/region. The adaptor converts AC power to DC power and reduces the voltage supplied to this computer .
User ’s Manual 3-1 Chapter 3 Getting S t arted This chapter provides basic information to start using your computer . It covers the following topics: ■ Connecting the AC adaptor ■ Opening the di.
User ’s Manual 3-2 Getting S tarted Connecting the AC adaptor Attach the AC adaptor when you need to cha rge the battery or you want to operate from AC power . It is also th e fastest way to get started, because the battery pack will need to be charged before you can operate from battery power .
User ’s Manual 3-3 Getting S tarted ■ Always use the TOSHIBA AC adaptor that was included with your computer or use AC adaptors specif ied by TOSHIBA to avoid any risk of fire or other damage to the computer . Use of an incompatible AC adaptor could cause fire or damage to the computer possibly resultin g in serious injury .
User ’s Manual 3-4 Getting S tarted 1. Connect the power cord to the AC adaptor . Figure 3-1 Connecting the power cord to the AC adap tor (2-pin plug) Figure 3-2 Connecting the power cord to the AC adap tor (3-pin plug) 2. Connect the AC adaptor' s DC output plug to the DC IN 19V jack on the right side of the computer .
User ’s Manual 3-5 Getting S tarted Opening the display The display panel can be opened to a wide range of angles for optimal viewing. While holding down th e palm rest with one hand so that the mai.
User ’s Manual 3-6 Getting S tarted ■ When opening the panel, please be careful not to fo rce it beyond the point where it moves easily . ■ Be careful not to open the display panel too far as this could put stress on the display panel’s hinges and cause damage.
User ’s Manual 3-7 Getting S tarted T urning on the power This section describes how to turn on the power - the power indicator light will then indicate the status. Please refer to the Monitoring of power condition section in Chapter 6, Power and Power-up Modes for more information.
User ’s Manual 3-8 Getting S tarted T urning off the power The power can be turned off in one of three modes, either Shut Down Mode, Hibernation Mode or Sleep Mode.
User ’s Manual 3-9 Getting S tarted Benefits of Hibernation Mode The Hiberna tion Mode feature provi des the following ben efits: ■ Saves data to the hard disk drive when the computer automatically shuts down because of a low battery condition. ■ Y ou can return to your previo us working environment immediately when you turn on the computer .
User ’s Manual 3-10 Getting S tarted Sleep Mode If you have to interrupt your work, you are able to tu rn off the power without exiting from your software by placing the computer into Sleep Mode.
User ’s Manual 3-1 1 Getting S tarted Executing Sleep Mode Y ou can e nter Sleep Mode in one of four ways: ■ Click Start then cl ick the power button ( ) located in the powe r management buttons ( ).
User ’s Manual 3-12 Getting S tarted Rest arting the computer Certai n conditions requi re that you reset the computer , for example if: ■ Y ou ch ange certain computer settings. ■ An error occurs and the computer does not respond to your keyboard commands.
User ’s Manual 3-13 Getting S tarted Creating Optical Reco very Discs This section describes how to create Recovery Discs. A recovery image of the software on your computer i s stored on the hard disk drive, and can be copied to DVD media by using the following steps: 1.
User ’s Manual 3-14 Getting S tarted Restoring the pre-in stalled sof tware from the Recovery hard disk drive A portion of the total hard disk dr ive space is configured as a hidden recovery partition. This p artition stores files which can be used to restore pre-installed software in the event of a problem.
User ’s Manual 3-15 Getting S tarted Restoring the pre-inst alled softw are from your created Recovery Discs If the pre-installed files are damaged , you are able to either use the Recovery Discs you have created or the hard disk drive recovery proce ss to restore the computer to the state it was in when you originally received it.
User ’s Manual 4-1 Chapter 4 Operating Basics This chapter describes the basic operations of your computer an d highlights the precautions that should be taken when using it. Using the T ouch Pad T o use the T ouch Pad, simply touch and move your fingertip across it in the direction you want the on-screen pointer to go.
User ’s Manual 4-2 Operating Basics The two butt ons below the T ouch Pad are used like the but tons on a standard mouse - press the left butt on to select a menu item or to manipulate text or graphics designated by the po inter , and press the rig ht button to display a menu or other function depending on the software you are using.
User ’s Manual 4-3 Operating Basics 2. Grasp the disc tray gently and pull until it is fully op ened. Figure 4-3 Pulling the disc tray open 3. Lay the CD/DVD, label side up, in the disc tray .
User ’s Manual 4-4 Operating Basics 4. Press the center of the CD/DVD gently until you feel it click into place on the center spi ndle. The disc shoul d be slightly below the top of the spindle and flush with the spindle base . 5. Press the center of the disc tray in order to close it - the tray will click into place when it is locked.
User ’s Manual 4-5 Operating Basics 2. The CD/DVD media will extend slig htly over the side s of the disc tray in order that you can hold it. Grasp it carefully by its edges and lift it vertically off of the central spind le and out of the tray . Figure 4-5 Removing a CD/DVD 3.
User ’s Manual 4-6 Operating Basics Function buttons This section describes the Function b uttons. Four buttons located next to the Power button are provided with some models.
User ’s Manual 4-7 Operating Basics Import ant message Before you write or rewrite to an y of the media supported by the DVD Super Multi drive, please read and follow all of the setup and operati ng instructions in this section.
User ’s Manual 4-8 Operating Basics ■ If the disc is poor in quality , or is dirty or damaged, wr i ting or rewriting errors may be noted - ensure that you check a ll discs for dirt or damage before you use them.
User ’s Manual 4-9 Operating Basics ■ Y ou can use both DVD-RAM discs that can be removed from a cartridge and DVD-RAM discs designed without a cartri dge. ■ Y ou ma y find that ot her computer DVD-ROM drives or other DVD players may not be able to read DVD-R, DVD-R (Dual Laye r), DVD-RW , DVD+R, DVD+R (Double Layer) or DVD+RW discs.
User ’s Manual 4-10 Operating Basics ■ Writing with software other than T OSHIBA Disc Creator has not been confirmed, therefore operation with other software applications ca nnot be guaranteed.
User ’s Manual 4-1 1 Operating Basics Disclaimer TOSHIBA does not bear responsibility for the following: ■ Damage to any CD-R, CD -RW , DVD-R, DVD-R (Dual L ayer), DVD-RW , DVD+R, DVD+R (Double Layer), DV D+RW or DVD-RAM disc that may be caused by writing or re writing with this product.
User ’s Manual 4-12 Operating Basics ■ If you add data to a DVD-R, DVD-R (Dual Layer), DVD+R or DVD+R (Double Layer) disc that you h ave already recorded to, you might not be able to read the ad ded data under some circumstances.
User ’s Manual 4-13 Operating Basics This whole sectio n need confirmwith new C orel DVD MovieFatory How to make a Labelflash DVD Simplified steps for making a Labelflash DVD: 1.
User ’s Manual 4-14 Operating Basics How to learn more about Corel DVD MovieFactory ® Please refer to the Help and Ma nual files for additional DVD MovieFacto ry information.
User ’s Manual 4-15 Operating Basics ■ Install, remove or connect external devices, including the following: SD/SDHC memory card , USB device, external display , and optical digital devices. ■ Please verify your disc after recording important dat a.
User ’s Manual 4-16 Operating Basics ■ Screen savers will not display while playin g a movie in th e "TOSHIBA DVD PLA YER". The compu ter will also no t go into Sl eep Mode, Hibernation Mode or shutdown while using "TOSHIBA DVD PLA Y ER".
User ’s Manual 4-17 Operating Basics S tarting TOSHIBA DVD PLA YER Use the following procedure to start "TOSHIBA DVD PLA YER". 1. Insert an DVD-Video in the DV D Super Multi drive while Windows Vist a ® is running . When an DVD-Video disc is set in the DVD drive, the following application sel ection scre en may appe ar .
User ’s Manual 4-18 Operating Basics 7. If your CD's or DVD's become dusty or dirty , wipe th em with a clean dry cloth from the center hole outwards - do not wipe in a circular direction.
User ’s Manual 4-19 Operating Basics Sound system This section describes some of the audio control functions. Adjusting System V olume Y ou can control the o verall level of sound using Windows V olume Mixer . T o launch V olume Mixer, follow the steps below .
User ’s Manual 4-20 Operating Basics Information Click the information button to view hardware information, software information, and language se tting. Speaker Configuration Click the playback bu tton to confirm the internal speakers or the headphone sound is coming from the right directi on.
User ’s Manual 4-21 Operating Basics Figure 4-8 Web Camera 1 2 3 1. Microphone 2. Web Camera 3. Web Camera LED ■ Make sure to remove the protective plastic-film befo re using the Web Camera. ■ Do not point the web came ra directly at the sun. ■ Do not touch or press strongly on the web camera lens.
User ’s Manual 4-22 Operating Basics Using TOSHIBA W eb Camera Appli cation TOSHIBA W eb Camera App lication is pre-configured to start when yo u turn on Windows Vista ® ; if you need to restart it go to St a rt → A ll Programs → TOS HI BA → Utilities → W eb Camera Applic ation .
User ’s Manual 4-23 Operating Basics Using TOSHIBA Face Recognition TOSHIBA Face Recognition uses a face verificati on library to verify the face data of users when they log in Windows. The user can thus avoid having to enter a password or the like, which makes the login process easier .
User ’s Manual 4-24 Operating Basics 2. Click the Register face button in the Ma nagement screen. The Registration screen is displayed. 3. Click the Next butto n to start the guide. 4. First, take a picture while moving your neck slightly to the left and right.
User ’s Manual 4-25 Operating Basics 3. Click the Delete b utton. "Y ou are about to delete the user d ata . Would you like to continue? " will be displayed on the screen. ■ If you do not want the data to be deleted, click the No button and you will then be returned to the Management screen.
User ’s Manual 4-26 Operating Basics 7. V erificatio n will be performed. If the authentication is successful, the image data taken in step 6 will be faded in and placed over one another . 8. Windows Welcome screen will be displayed, and wil l be logged in automatically to Wind ows.
User ’s Manual 4-27 Operating Basics 1. Click Start → All Programs → TOS HI BA → Networking → Modem Region Select . 2. The Region Selection icon will appear in the Windows T askbar .
User ’s Manual 4-28 Operating Basics Modem Sele ction If the computer cannot recognize the internal modem, a dialog box is displayed from which you should select the appropriate communications port for your modem to use. Dialing Propertie s Y ou should select this item in order to display the diali ng properties.
User ’s Manual 4-29 Operating Basics 2. Pinch the lever on the pl ug in the computer's modem jack and pull it out from within the computer . Wireless com munications The computer's wireless communicat ion function supp orts both Wireless LAN and Bluetooth devices.
User ’s Manual 4-30 Operating Basics Security ■ TOSHIBA strongly recommend that y ou enable encryption functionality , otherwise your computer will be open to illegal access by an outsider using a wireless connection. If this occurs, the outsider may illegally access your system, eavesdrop, or cause the loss or destruction of stored data.
User ’s Manual 4-31 Operating Basics Release Notes related to the Bluetooth ® Stack for Windows ® by TOSHIBA 1. Fax application software: ■ Please be aware that there is some fax application software that you cannot use on this Bluetooth TM S tack.
User ’s Manual 4-32 Operating Basics Wireless communication indicator The wireless communication indicator shows the status of the computer's wireless com munication function s.
User ’s Manual 4-33 Operating Basics LAN The computer has built-in suppo rt for Ethernet LAN (10 megabits per second, 10BASE-T) and Fast Ethernet LAN (100 megabits per second, 100BASE-TX).
User ’s Manual 4-34 Operating Basics 2. Plug one end of the cable into t he LAN jack. Press gently until you hear the latch click into place. Figure 4-1 1 Connectin g the LAN cable 3. Plug the other end of the cable into a LAN hu b connector or router .
User ’s Manual 4-35 Operating Basics Cleaning the computer T o help ensure long, trouble-free o per ation, keep the computer free of dust and dirt, and u se care with a ll liquids arou nd it.
User ’s Manual 4-36 Operating Basics ■ Close the display panel. ■ Do not pick up the comput er by its display p anel. ■ Before carrying your computer , shut it down, disconnect the AC ad aptor and allow it to cool down - a failure to follow this instruction may result in minor heat injury .
User ’s Manual 5-1 Chapter 5 The Keyboard The computer's keyboard layouts are compatible with a 104/105-key enhanced keyboard - by pressing some keys in combination, all of the 104/105-key enhance d keyboard functions can be performed on the computer .
User ’s Manual 5-2 The Keyboard Function keys: F1 … F12 The function keys (not to be confused with the special FN key) are the twelve keys at the top of your key board - these keys function differentl y from other keys.
User ’s Manual 5-3 The Keyboard Hot keys Hot keys (pressing FN + a function or ESC key) let you enable or disable certain features of the computer . Mute: Pressing FN + ESC turns the volume on and off. Lock: Pressing FN + F1 enters ''Lock computer mode''.
User ’s Manual 5-4 The Keyboard Brightness (Up) : Pre ssing FN + F7 increases the computer's displa y panel brightness in individual steps. Wireless: Pressing FN + F8 switches the active wireless devices. T ouch Pad: Pressing FN + F9 enables or disables the T ouch Pad function.
User ’s Manual 5-5 The Keyboard Windows special keys The keyboard p rovides two keys tha t have special functio ns in Windows: Windows S tart Button activates the Start men u and the other , the application key , has the same fu nction as the secondary mouse button.
User ’s Manual 6-1 Chapter 6 Power and Power-up Modes The computer's power resources incl ude the AC adaptor and internal batteries. This chapter gives details on making the most effective use of these resources including charging and ch anging batteries, tips for saving battery power , and po wer-up modes.
User ’s Manual 6-2 Power and Power-up Modes T a ble 6-1 Power conditions continued Power indica tors As shown in the below table, the Battery , DC IN and Power indicators on the system indicator alert you to the computer ’s operating capability and battery charge status.
User ’s Manual 6-3 Power and Power-up Modes DC IN indicator Check the DC IN indicator to determine t he power status with the AC adaptor connected - the follow ing indi cator conditions shou ld be n.
User ’s Manual 6-4 Power and Power-up Modes Real T ime Clock battery The Real Time Clock (RTC) battery provides power fo r the internal real time clock and calendar function and also main tains the system configuration while the computer is turned off.
User ’s Manual 6-5 Power and Power-up Modes Care and use of the battery p ack The battery pack is a vita l compon ent of portable computing and, as such, taking proper care of it will help ensure a longer operating time on battery power as well as deli ver a longer life for you r battery pack.
User ’s Manual 6-6 Power and Power-up Modes Tim e The following table shows the approximate time required to fully charge a discharged battery . Battery charging notice The battery may not begin cha.
User ’s Manual 6-7 Power and Power-up Modes Repeat these steps two or three time s until the battery recovers no rmal capacity . Monitoring battery ca pacity Remaining battery power can be monitored using the following methods.
User ’s Manual 6-8 Power and Power-up Modes Ret aining data with power off When you turn off your computer with fully charged batteries, the batteries retain data for the following approximate time periods.
User ’s Manual 6-9 Power and Power-up Modes Replacing the battery p ack Please be aware that the battery pack is classified as a consumable item. The operating life of the battery pack will gradually reduce through repeated charging and discharging, and wi ll need to be replaced when it reaches the end of its operati ng life.
User ’s Manual 6-10 Power and Power-up Modes 6. Slide and hold the battery release latch (1 ) to disengage the battery pack and then remove it from the computer (2). Figure 6-2 Releasing the battery pack (2) T o install a battery , follow the steps as detailed below: 1.
User ’s Manual 6-1 1 Power and Power-up Modes T OSHIBA Password Utility The TOSHIBA Supervisor Password Utility allows you to maintain an additional level of security and provides two level s of password security: User and Supervisor .
User ’s Manual 6-12 Power and Power-up Modes T o enter a password manually , follo w these steps: 1. T urn on the power as described in Chapter 3, Getting S tarted. The following message wil l appear in the LCD: Enter Password [xxxxxxxx] 2. Enter the Password.
User ’s Manual 6-13 Power and Power-up Modes System aut o off This feature turns the system of f automat ically if it is not used for a set duration.
User ’s Manual 7-1 Chapter 7 HW Setup and Passwords This chapter explains how to us e TOSHIBA HW Setup program to configure your computer and how to set passwords. HW Setup TOSHIBA HW Setup allows y ou to configure setti ngs for General, Password, Display , Boot Prio rity , Keyboard, USB, LAN.
User ’s Manual 7-2 HW Setup and Passwords This window displays the BIOS version and contains two buttons: Setup This field displays BIOS V ersion and date. Password User Password This option allows you to set or reset the user password for power on.
User ’s Manual 7-3 HW Setup and Passwords If they do not match, the follow ing message appe ars. Y ou mus t repeat step 1. Incorrect Password!!! 4. Follow the same procedures d escribed in the earlier sectio n, How to set the password , to set a new user password.
User ’s Manual 7-4 HW Setup and Passwords USB Legacy USB Support Use this option to enable or disabl e USB Legacy Emulation. If your operating system does not support USB, you can still use a USB mouse and keyboard by setti ng the USB Legacy Emulation item to enabled.
User ’s Manual 8-1 Chapter 8 Optional Devices Optional devices can expand the computer's capabilities and its versatility . This chapter describes the connection or installation of the followin.
User ’s Manual 8-2 Optional Devices ExpressCard The computer is equi pped with a sin g le ExpressCard slot into w hich any ExpressCard device that meets industry standards, ei ther manufactured b y TOSHIBA or another vendor , can be in stalled.
User ’s Manual 8-3 Optional Devices 6. After inserting the ExpressCard you sho uld refer to its documentation and also check the configu ration in Wi ndows in o rder to ensure that it is correct. Removing an ExpressCard T o remove an ExpressCard, follow the steps as detailed below .
User ’s Manual 8-4 Optional Devices Bridge media slot The computer is equipp ed with a Bri dge medi a slot that can accommodate some kinds of memory media with vari ous memory capacities so that you can easily transfer data from devices, such as digital cameras and Personal Digital Assistants.
User ’s Manual 8-5 Optional Devices Memory media This section provides the important safety precautions in order to handle your memory media. Points to note about the SD/SDHC memory card SD/SDHC memory cards compl y with SDMI (Secure Digital Music Initiative), which is a technology adopted to prevent unlawful copy or playback of digital music.
User ’s Manual 8-6 Optional Devices Additional memory module Y ou can install additional memory into th e computer in order to increase the amount of system memory that is avai lable. This section describes how to install and remove optional memory modules.
User ’s Manual 8-7 Optional Devices Inst alling a memory m odule The computer contains slots for two memory modules, one positioned immediately over the other - the proc edures are the same for installing either modul e.
User ’s Manual 8-8 Optional Devices 5. Seat the memory module cover in place and secure it with one scre w . Figure 8-5 Seating the memory module cover 6. Install the battery pa ck - refer to Replacing th e battery pack section in Chapter 6, Power and Power-up Modes , if required.
User ’s Manual 8-9 Optional Devices Removing a m emory module T o remove the memory module, follow the steps as detailed below: 1. Set the computer to Boot Mode and turn its power of f - make sure the Power indicator is of f (refer to the T urning off the power section in Chapter 3, Getting S tarted if required).
User ’s Manual 8-10 Optional Devices USB floppy diskette drive The USB floppy diskette drive accommod ates e ither a 1.44MB or 720KB a 3 2/1" floppy diskette and connects to one of the computer's USB ports. Figure 8-6 USB floppy diskette drive The USB floppy diskette drive is available only as an option.
User ’s Manual 8-1 1 Optional Devices Using the USB floppy diskette drive The USB floppy diskette drive accommodates either a 1.44MB or 720KB floppy diskette and connects to one of the computer's USB ports.
User ’s Manual 8-12 Optional Devices Disconnecting the USB floppy diskette drive When you have finished using the USB floppy diskette drive, you can follow the procedures below in order to disconnect it: 1. W ait for the Disk-In-Use Indicator light to go out to make sure all floppy diskette activity has stopped.
User ’s Manual 8-13 Optional Devices Disconnecting an eS A T A device When you have finished using an eSA T A device, you can follow the procedures below in order to disconnect it: 1. W ait fo r the indica tor light of an eSA T A devi ce to go out to make sure all activity has stopped.
User ’s Manual 8-14 Optional Devices Figure 8-9 Connecting the monitor ca ble to the external monitor port 3. T urn the external monitor ’s power on. 4. T urn the computer's powe r on. When you turn on the power , th e computer will automatically recog nize the monitor and determine whether it is a color or monochrome device .
User ’s Manual 8-15 Optional Devices HDMI The Video data on your computer can be viewed on a TV set. T o do so, connect your computer ’s HDMI out port to the TV using the HDMI out cable. Y ou can use the hotkeys FN + F5 to change the display device.
User ’s Manual 8-16 Optional Devices Settings for display video o n HDMI T o view video on the HDMI device, be sure to configure th e following settings otherwise you may find that nothing is displayed. Settings for Audio on HDMI T o set the audio device to use the HDMI, follow the steps below .
User ’s Manual 8-17 Optional Devices Select HD Form at T o select the display mode, follow the steps as detailed below: 1. Click Start and click Control Panel . 2. Click Appearance and Personalization . 3. Click Personalization . 4. Click Display Settings .
User ’s Manual 8-18 Optional Devices Security lock A security locks enable you to anchor your computer to a desk or other heavy object in order to help prevent unauthorized removal or theft.
User ’s Manual 9-1 Chapter 9 T roubleshooting TOSHIBA have designed this computer for durability , ho wever , should problems occur you are able to use the procedures detailed in this chapter to help determi ne the cause.
User ’s Manual 9-2 T roubleshooting Preliminary c hecklist Y ou should always consider the simple st solution first - the items detailed in this checklist are easy to fix and yet may cause what appe.
User ’s Manual 9-3 T roubleshooting Record your observations so you can describe them in detail to your reseller , dealer or service provider . Hardware and system checklist This section discusses problems ca used by your computer ’s hardware or attached peripherals.
User ’s Manual 9-4 T roubleshooting Self test While booting up the computer , self te st is exe cuted aut omatically a nd the following will be displaye d: This message remains on the screen for a few seconds.
User ’s Manual 9-5 T roubleshooting Overheating power down If the processor's temperature reaches an unacceptably high level with either setting, the computer will auto matically shut down to prevent any damage - in this instance all unsaved data in memory will be lost.
User ’s Manual 9-6 T roubleshooting Battery If you suspect a problem with the battery , you shoul d check the status of the DC IN in dicator as well as the Battery indicator . Please refer to Chapter 6, Power and Power-up Modes for more information on these indicators, together with general battery operation.
User ’s Manual 9-7 T roubleshooting Real Time Clock Password Keyboard Keyboard problems can be caused by the setup and conf iguratio n of the computer - please refer to Chapter 5, The Keyboard for further information. Problem Pro cedure The following message is displayed on the LCD: RTC battery is low or CMOS checksum is inconsistent.
User ’s Manual 9-8 T roubleshooting Internal display p anel Apparent display panel problems may b e related to the computer's setup and configuration - please refer to Chapter 7, H W Setup and Passwords , for further information.
User ’s Manual 9-9 T roubleshooting Solid S tate Drive Hard disk drive Problem Pro cedure Computer does not boot from hard disk drive Check to see whether that is a floppy diskette in the floppy diskette drive or a CD-ROM/DVDROM in the optical disc drive - if so remove it and try to start the computer again.
User ’s Manual 9-10 T roubleshooting DVD Supe r Multi drive For further information, please refer to Chapter 4, Operating Basics . Problem Pro cedure Y ou cannot access a CD/DVD in the drive Make sure the drive's disc tray is securely closed - press it gently into the computer until it clicks into place.
User ’s Manual 9-1 1 T roubleshooting USB floppy diskette drive The USB floppy diskette d rive is available o nly as an option. For further information, please refer to Chapter 4, Operating Basics . Some CD/DVD/DVDs run correctly , but others do not The computer's software or hardware configuration may be causing a problem.
User ’s Manual 9-12 T roubleshooting ExpressCard For further information, please refer to Chapter 8, Optional Devices . SD/SDHC memory card, mi niSD/microSD Card For further information, please refer to Chapter 8, Optional Devices .
User ’s Manual 9-13 T roubleshooting Memory S tick/Memory S t ick PRO For further information, please refer to Chapter 8, Optional Devices . MultiMediaC ard For further information, please refer to Chapter 8, Optional Devices .
User ’s Manual 9-14 T roubleshooting Pointing device If you are using a USB mouse, you should also refer to both the USB device section in this chapter , and the documen tation supplied with your mouse.
User ’s Manual 9-15 T roubleshooting The mouse poi nter moves too fast or too slow In this instance, you should initiall y try changing the speed setting within th e Mouse Control utility . 1. T o access this utility , click Sta rt → Control Panel → Hardware and Sound → Mouse icon.
User ’s Manual 9-16 T roubleshooting USB mouse USB device In addition to the information in this section, p lease also refer to the documentation supplied with yo ur USB device. Problem Procedure On-screen pointer does not respond to mouse operation In this instance the system might be busy .
User ’s Manual 9-17 T roubleshooting eSA T A device In addition to the information in this section, p lease also refer to the documentation supplied with your eSA T A device . Problem Procedure USB device does not work Remove the USB device from the computer and then reconnect it to a free port in order to ensure it is firmly attached.
User ’s Manual 9-18 T roubleshooting Additional mem ory module Please also refer to Chapter 8, Optional Devices , for further information on installing and removing memory modul es. Problem Procedure If there is a memory malfunction, the Power indicator will repeatedly flash (on for 0.
User ’s Manual 9-19 T roubleshooting Sound system In addition to the information in this section, p lease also refer to the documentation supplied with your a udio device. V olume control Problem Pro cedure No sound is heard A djust the volume control.
User ’s Manual 9-20 T roubleshooting External monitor Please also refe r to Chapter 8, Optional Devices , and to the documentation supplied with yo ur monito r for further information.
User ’s Manual 9-21 T roubleshooting Modem This information is appl icable to the models equipped with a built-in modem. Problem Procedure Communication software can’t initialize modem Make sure the computer's intern al modem settings are correct.
User ’s Manual 9-22 T roubleshooting LAN Wireless LAN If the following procedures do not re store LAN access, consult your LAN administrator . For more information on wireless communication, refer to Chapter 4, Operating Basics . Bluetooth For further information on Bluetooth wire less communication, please refer to Chapter 4, Operating Basics .
User ’s Manual 9-23 T roubleshooting HDMI m onitor output function T OSHIBA support If you require any additional help using your compu ter or if you are having problems operating the computer, you may need to cont act TOSHIBA for additional techni cal assistance.
User ’s Manual 9-24 T roubleshooting Where t o writ e If you are still unable to solve the prob lem and suspect that it is hardware related, write to TOSHIBA at the nearest location listed below: Outside of Europe In Europe Australia TOSHIBA Australia Pty .
User ’s Manual 10-1 Chapter 10 Disclaimers This chapter slates the Disclaime r(s) information applicable to TOSHIBA computers. CPU Central Processing Unit ("CP U") Performance Disclaimer.
User ’s Manual 10-2 Disclaimers Under some conditions, your computer product may automatically shut- down. This is a normal protective feat ure designed to reduce the risk of lost data or damage to the product when used outside recommended conditions.
User ’s Manual 10-3 Disclaimers Battery Life Battery life may vary considerably depend ing on product model, configuration, applications, power ma nagement settings and features utilized, as well as the natural perf ormance variations produced by the design of indi vidual compone nts.
User ’s Manual 10-4 Disclaimers Wireless LAN The transmission speed over th e wireless LAN and th e distance over which wireless LAN can re ach may vary depen ding on surro unding electromagnetic environment, obstacles, access po int design and configuration, and client design and so ftware/hardware configurations.
User ’s Manual Appendixes-1 Appendixes T able of Content s Appendix A S pecifications................... ...................... ....................... ................ A-1 Appendix B Display Controller ............ .................... ............
User ’s Manual A-1 Appendix A S pecifications This appendix summarizes the computer ’s technical specifications. Environme nt al require ment s Power Requirement s Operating Non-oper ating Ambient.
User ’s Manual A-2 Built-in Mod em The ability of th is feature is d epending on th e model you pu rchased. Network control unit (NCU) T ype of NCU AA T ype of line T elephone line (analog only) T y.
User ’s Manual B-1 Appendix B Display Controller Display controller The display controller in terprets software commands into hardware commands that turn particular pixels on or off.
User ’s Manual C-1 Appendix C V .90/V .92 The TOSHIBA internal modem uses V .90 technolog y . The modem is capable of downstream speeds of 56Kbps (kilobits per second) when connected to an Internet service provi der that su pports V .
User ’s Manual C-2 T able Result cod es for a V .90 connection *EC stands for the Error Control me thod, which appears only when the extended result codes configuration op tion is enabled . EC is replaced by one of the following symbols, depending on the error control method used.
User ’s Manual C-3 A T Command -V90=* V .90 Dia l Line Rate -V90 sets the maximum V .90 downstream that the modem attempts to connect -V90=0 V .90 di sabled -V90=1 V .
User ’s Manual D-1 Appendix D Wireless LAN This appendix is intended to hel p you get your Wireless LAN network up and running, with a mi nimum of parameters. Card S pecifications Form Factor Mini Card Compati bility ■ IEEE 802.1 1 S tandard for Wireless LANS ■ Wi-Fi (Wireless Fidelity) certified by the Wi-Fi Alliance.
User ’s Manual D-2 Radio Characteristics Radio Characteristics of Wireless LAN Cards may vary according to: ■ Country/region where the product was purcha sed ■ T yp e of product Wireless communication is often subject to local radio regulations.
User ’s Manual D-3 T able Wireless IEEE 802.1 1 Channels Sets (Revision B and G) When installing Wireless LAN card s, the channel configuration is managed as follows: ■ For wireless clients that o.
User ’s Manual D-4 T able Wireless IEEE 802.1 1 Channels Sets (Revision A) Frequency Range Channel ID 5150-5850 MHz Note 36 5180 40 5200 44 5220 48 5240 52 5260 56 5280 60 5300 64 5320 100 5500 *3 1.
User ’s Manual D-5 *1 Factory-set defaul t channels *2 Refer to the sheet Approved Countries/Regi ons for use for the countries/regions that in which these channels can be used. *3 These channels are ava ilable to A/B/G/N combo type only . *4 Available Area: US (USA, CANADA) only .
User ’s Manual E-1 Appendix E AC Power Cord and Connectors The AC input plug of power cord must be compatible with various international AC power outlets. Power cords need to meet the local standards and the specifications liste d as below: Length: Minimum 1.
User ’s Manual E-2 Certification agencies In Europe, two conductors power cord must be VDE type, H05VVH2-F or H03VVH2-F and for three conductors power cord must be VDE type, H05VV -F .
User ’s Manual E-3 USA Australia Europe United Kingdom Canada China.
User ’s Manual F-1 Appendix F T OSHIBA PC Health Monitor The TOSHIBA Health Monitor soft ware program monitors computer system functions such as power consumpt ion, the cooling system and HDD Drop sensor . It al erts users of specific system conditi ons via pop-up messag es.
User ’s Manual F-2 The TOSHIBA PC Health Monitor software does not extend or modify TOSHIBA's obligations under its st andard li mited warranty in any way . TOSHIBA's st anda rd limited warranty terms and limitations apply . Visit http://www .
User ’s Manual Glossa ry-1 Glossary The terms in this glossary cover topi cs related to this manual. Alternate naming is included for reference. Abbreviations AACS: advanced access content system AC.
User ’s Manual Glossa ry-2 Glossary HD+: High Definition Plus IDE: integrated drive el ectronics IEEE: Institute of Electrical and Electronics Engineers I/O: input/output IrDA: Infrared Data Associa.
User ’s Manual Glossa ry-3 Glossary alphanumeric: Keyboard characte rs including letters, numbers and other symbols, such as punctuation ma rks or mathematica l symbols. alternating current (AC): Electric current that reve rses its directi on of flow at regular intervals.
User ’s Manual Glossa ry-4 Glossary buffer: The portion of the computer ’s me mo ry where data is temporarily stored. Buffers often compe nsate for differences in the rate of flow from one device to another . bus: An interface for transmission of signals, data or electric power .
User ’s Manual Glossa ry-5 Glossary comp atibility: 1) The ability of one compu ter to accept and process d ata in the same manner as another comp uter without modifying th e data or the media upon which it is b ein g transferred. 2) the ability of one device to connect to or comm unicate with another system or component.
User ’s Manual Glossa ry-6 Glossary device drive r: A program (called a "driver") that pe rmits a computer to communicate with a device. dialog bo x: A window that accepts user in put to make system settings or record other info rmation. disable: T o turn a computer optio n off.
User ’s Manual Glossa ry-7 Glossary E echo: T o send back a reflection of the transmitted data to the sending device. Y ou can display th e information on the screen, or output it to the printer , or both.
User ’s Manual Glossa ry-8 Glossary H hard disk: A storage device composed of a rigid platter or platters that can be magnetically coded with data. Hard disks hold much more information than diskettes and are used fo r long-term storage of programs and data.
User ’s Manual Glossa ry-9 Glossary K K: T aken from the Greek word kilo, m eaning 1000; often used as equivalent to 1024, or 2 raised to the 10 th power . See a lso byte and kilobyte . keyboard: An input device containing switch es that are activated by manually pressing marked keys.
User ’s Manual Glossary-10 Glossary mode: A method of operation, for exam ple , the Shut Down Mode, Sleep Mode or the Hiberna tion Mode. modem: Derived from modulator/demod ul ator , a device that c.
User ’s Manual Glossary-1 1 Glossary P PA L : P AL (Phase Alternating Lin e) is the dominant video and broadcasting standard in Europe. pa r it y : 1) The symmetrical relationship between two parameter values (integers) both of which are either on or off; odd or even; 0 or 1.
User ’s Manual Glossary-12 Glossary Random Access Memory (RAM): V olatile memory that can be written to as well as read. V o latile here means that information in RAM is lost when you turn off your computer. This type of memory is used for your computer's main memory .
User ’s Manual Glossary-13 Glossary system disk: A diskette that contains the operating system files needed to start the computer . Any diskette can be formatted as a system disk. A system disk is also called a "b oot able disk", "boot disk" or a "startup dis k.
User ’s Manual Index-1 Index A AC adaptor, 1-7 additional, 1-16 connecting, 3-2 DC IN 19V jack, 2-5 ASCII characters, 5-5 B Battery charging, 6-5 extending ba ttery life, 6-8 indicator, 2-11, 6- 2 M.
User ’s Manual Index-2 FN + F8 (Wireless), 5-4 FN + F9 (Touch Pad), 5-4 FN + spac e (Zoom), 5-4 Function buttons, 4-6 Function keys, 5-2 H Hard disk drive, 2-6 automatic power off, 1-10 HDMI, 8-15 H.
User ’s Manual Index-3 indicator, 6-3 panel power on/off, 6- 12 Shut Down mo de (Boot M ode), 3-8 Sleep Mode, 3-10 system auto off, 6-13 turning off, 3 -8 turning on, 3 -7 Problems AC power, 9-5 Ana.
User ’s Manual Index-4 V Video RAM, 1-4 W Web Camera, 1-8 Wireless communication, 4-29 Wireless LAN, 1-9, 4-29 problems, 9-22.
Ein wichtiger Punkt beim Kauf des Geräts Toshiba toshiba satellite user's manual (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Toshiba toshiba satellite user's manual noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Toshiba toshiba satellite user's manual - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Toshiba toshiba satellite user's manual reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Toshiba toshiba satellite user's manual erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Toshiba toshiba satellite user's manual besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Toshiba toshiba satellite user's manual verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Toshiba toshiba satellite user's manual. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Toshiba toshiba satellite user's manual gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
