Benutzeranleitung / Produktwartung IK-TF7C des Produzenten Toshiba
Zur Seite of 36
For Customer Use Enter below the Serial No . which is located on the bottom of the cabinet. Retain this inf or mation f or future ref- erence. Model No.
2 SAFETY PRECAUTIONS Safety icons This manual contains safety instructions that must be observed in order to avoid potential hazards that could result in personal injuries, damage to your equipment, or loss of data.
3 Disclaimer We disclaim an y responsibility and shall be held harmless for any damages or losses incurred b y the user in any of the f ollowing cases: 1. Fire, earthquake or any other act of God; acts by third par ties; misuse by the user , whether inten- tional or accidental; use under extreme operating conditions.
4 1. CAUTIONS ON USE AND INST ALLA TION ..... 5 2. COMPONENTS ................................................ 5 3. ITEMS CONTROLLED BY USING ON SCREEN DISPLA Y .................................... 6 4. NAMES AND FUNCTIONS ............................
5 1. CAUTIONS ON USE AND INST ALLA TION • Carefully handle the units. Do not drop, or giv e a strong shock or vibration to the camera. This ma y cause problems . T reat the camera cables carefully to pre vent cab le problems, such as cable breakdown and loosened connec- tions.
6 3. ITEMS CONTROLLED BY USING ON SCREEN DISPLA Y MODE E. TRG MANU speed Syncro. scan. Partial scanning T rigger (1P SNR/SR) T rigger (PW SNR/SR) 1P exposure time MODE MANU MODE Color temperature MANU.
7 4. NAMES AND FUNCTIONS DISP PAGE DC IN 12V MENU DATA (AWB) 1 8 2 4 6 7 5 9 3 Prism faceplate DIGITAL terminal DISP button PAGE button [ Rear ] [ Front ] MENU UP button MENU DOWN button DATA UP (AWB) button DATA DOWN button DC IN 12V terminal 1 Prism faceplate The protection cap is attached on the lens mount por tion.
8 5. CONNECTION 5. 1 Standard Connection 5. 2 Cautions on Connection • When connecting the camer a cables, unplug the po wer source of the camera and the other equipment connected. • W e suggest using a C mount lens made for a 3CCD camer a. When using another lens, the best camera perf or mance of this camera may not be obtained.
9 6. OPERA TION 1 Refer to the item " 5. CONNECTION", connect each equipment correctly . 2 T urn on the connected equipment and the power source of the camera. 3 P oint the lens at the object, operate the lens iris adjustment, focus adjustment, etc.
10 2 MANU (Manual white balance) • Set the MODE to MANU on the WHT BAL menu. (Refer to the item "7.2 (3) WHT BAL (white balance)".) • Shoot a known white object, adjust the white balance adjusting the levels of R GAIN and B GAIN on the menu, confirming with a monitor or a monitor etc.
11 7. MODE SETTING BY ON SCREEN DISPLA Y V ar ious settings can be controlled on the unit by using the on screen men u display ed on the monitor . The contents once set are memorized ev en if the power source is turned off , so it is unnecessar y to set again when using the unit next time.
12 7. 2 Menus • Select the menu to change the setting by referring the item "7.1 Using the Menus".) • When the [MENU UP], [MENU DOWN] buttons are pushed, the " → " on the screen moves up and down. Move the " → " to the item to change.
13 (1. 2) Changing each setting in SS (synchro. scan) mode (a) Changing the shutter speed setting 1 Set the " → " to SS by pushing [MENU UP], [MENU DO WN] buttons . 2 Select the shutter speed by pushing [D A T A UP], [DA T A DOWN] b uttons.
14 (1. 3) Changing each setting in E.TRG mode The E.TRG has five modes; 1P SNR, 1P SR, PW SNR, PW SR, RR. First set the " → " to MODE and select E.
15 (1. 3. 2) Changing each setting in 1P SR mode (a) Changing the polarity of inputting trigger pulse setting 1 Set the " → " to TRG.P by pushing [MENU UP], [MENU DO WN] buttons. 2 Select either , by pushing [D A T A UP], [DA T A DOWN] buttons .
16 (1. 3. 3) Changing each setting in PW SNR mode (a) Changing the polarity of inputting trigger pulse setting 1 Set the " → " to TRG.P by pushing [MENU UP], [MENU DO WN] buttons. 2 Select either , by pushing [D A T A UP], [DA T A DOWN] b uttons.
17 (1. 3. 4) Changing each setting in PW SR mode -- SHUTTER -- MODE E.TRG E.TRG PW SR TRG.P PART OFF <MODE = E.TRG E.TRG = PW SR> • Partial scanning switch OFF/60fps/90fps/E.
18 (1. 3. 5) Changing each setting in RR mode (a) Changing the partial scanning setting 1 Set the " → " to P ART by pushing [MENU UP], [MENU DO WN] buttons. 2 Select either OFF/60fps/90fps/E.60fps/E.90fps by pushing [D A T A UP], [DA T A DOWN] b uttons.
19 ( 3 ) WHT BAL (White balance) WHT BAL has two modes; A WB, MANU . Set the " → " to MODE, push the [D A T A UP], [DA T A DOWN], and select mode among A WB, MANU. (3. 1) Changing each setting in AWB (Automatic White Balance) mode (a) Changing color temperature setting 1 Set the " → " to C.
20 ( 4 ) PROCESS (4. 1) Changing master pedestal 1 Set the " → " to M. PED by pushing [MENU UP], [MENU DO WN] buttons. 2 Set the master pedestal by pushing [D A T A UP], [DA T A DOWN] b uttons. (4. 2) Changing R pedestal 1 Set the " → " to R.
21 ( 5 ) SYNC When an external sync signal is input, the display menu changes from INT (internal sync) to EXT (external sync) automatically . (5. 1) Adjusting horizontal phase 1 Set the " → " to H PHASE by pushing [MENU UP], [MENU DO WN] buttons .
22 7. 3 External Sync When using the unit with an e xter nal sync signal, input HD and VD to CC3 and CC4 of the DIGIT AL ter minal. When the external sync signal is input, the camera automatically switches its sync from the internal sync to the external sync.
23 ( 3 ) Using the unit with external sync signal When adjusting H (horizontal) phase refer to the item "7.2 (5) (5.1) Adjusting horiz ontal phase".
24 7. 5 EXT TRIG (External trigger) Charge begins to accumulate after the trigger input to CC1 of the DIGIT AL terminal, and 1 frame images are output.
25 About 1 µ s Exposure period* 2 Exposure period* 2 T rigger* 1 Negative polarity mode P ositive polarity mode RGB data (video interval image) (Internal VD) * 3 FV AL L V AL, DVA L 28H (P ar tial scanning OFF) 38H (P ar tial scanning 60fps) 47H (P ar tial scanning 90fps) ger , there will be an effect on the video.
26 ( 2 ) 1P SR (1 Pulse T rigger Sync Reset) Charge begins to accumulate after the trigger input to CC1 of the DIGIT AL terminal, the ver tical sync signal is reset and frame images are output. (2. 1) 1 Pulse T rigger SYNC-RESET Picture Output Timing *1: Exter nally input signal *2: Exposure time is determined by the setting of "7.
27 ( 3 ) PW SNR (Pulse width trigger SYNC-NON RESET) The trigger input to CC1 of the DIGIT AL ter minal dev elops 1 frame images. (3. 1) Pulse Width T rigger SYNC-NON RESET Picture Output Timing (At T.
28 (3. 2) Pulse Width T rigger SYNC-NON RESET Picture Output Timing (at T ime of Internal Sync) *1: Exter nally input signal *2: Exposure time = T rigger pulse width + 6 µ s (V alid tr igger pulse width is 2 µ s or greater f or external trigger shutter operation.
29 ( 4 ) PW SR (Pulse width trigger SYNC-RESET) The trigger input to CC1 of the DIGIT AL ter minal dev elops 1 frame images. (4. 1) 1 Pulse Width T rigger SYNC-RESET Picture Output Timing *1: Exter na.
30 ( 5 ) RR (Reset restart) Input of an external reset-restart signal (CC4 of the DIGIT AL terminal: External VD input) permits one screen of information to be output at an arbitrary timing.
31 7. 6 Partial Scanning 1/29.2s (796H) Video interval image Blanking interval B Blanking interval D T otal A Video interval C RGB data (video interval image) (Internal VD) FV AL L V AL, DVA L Video p.
32 8. INPUT OUTPUT SIGNAL SPECIFICA TOINS 2.0 µ s to 5.0 µ s (P ositive polarity mode) (Negative polarity mode) More than 2 µ s More than 2 µ s 5H to 21H ( 6 ) External HD/VD Input Phase Specifications 100 100 External HD rising edge Center Unit : Clock 1 clk=33.
33 9. CCD OUTPUT W A VEFORM TIMING CHART ( 1 ) Horizontal Output W aveform Timing Chart 246 clk 40 clk CLK=33.9 nsec (29.5 MHz) 164 clk 29 clk 3 clk 5 clk 33.
34 10. SPECIFICA TIONS P ower supply P ower consumption Pick-up system Image sensor (Effectiv e pixels) Scanning system Scan frequency Sync system Horizontal resolution Sensitivity Minimum illuminatio.
35 12. BEFORE MAKING A SER VICE CALL Symptom No image P oor color Items to be checked • Is the power supplied correctly? • Is the lens iris adjusted correctly? • Are the cables connected correct.
LIMITED W ARRANTY TOSHIBA CCD CAMERA Promptly register your product with T oshiba on-line at www.toshiba.com/taisisd. By registering your prod- uct you will be eligib le for periodic updates, announcements, and special off ers.
Ein wichtiger Punkt beim Kauf des Geräts Toshiba IK-TF7C (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Toshiba IK-TF7C noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Toshiba IK-TF7C - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Toshiba IK-TF7C reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Toshiba IK-TF7C erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Toshiba IK-TF7C besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Toshiba IK-TF7C verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Toshiba IK-TF7C. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Toshiba IK-TF7C gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
