Benutzeranleitung / Produktwartung AFG3000 des Produzenten Tektronix
Zur Seite of 230
This document supports fi rm ware version 1.0.0 and above. www.tektronix.com Reference Manual AFG3000 Series Arbitrary/Function Generators 071-1639-00.
Copyright © T ektronix, Inc. All rights reserv ed. T ektronix products are covered by U.S. and foreign patent s, issued and pending. Information in this publication supercedes that in all previously published material. Specif ications and price change pri vileges reserv ed.
W ARRANTY 16 T ektronix warrants that the product will be free from defects in m aterials and workmanship for a period of three (3) years from the date of original purchase from an author ized T ektronix distributor .
.
AFG3000 Series Arbitrary/Functio n Generators Reference Manual i T able of Contents General Safety Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix Preface . . . . . . . . . . . . . . . . . . . . .
T able of Contents ii AFG3000 Series Arbitrary/Function Generators Reference Manual MMEMory:LO AD:TRA Ce (No Query F orm) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-28 MMEMory:LOCK[:ST A T e] . . . . . . . . . . . . . . . . . . . . .
T able of Contents AFG3000 Series Arbitrary/Functio n Generators Reference Manual iii [SOURce[1|2]]:PM:INT ernal:FUNCtion:EFILe . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-64 [SOURce[1|2]]:PM:SOURce . . . . . . . . . . . . . . . . . . . .
T able of Contents iv AFG3000 Series Arbitrary/Function Generators Reference Manual TRA Ce|D A T A [:D A T A]:LINE (No Query Form) . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-100 TRA Ce|D A T A[:DA T A]:V ALue . . . . . . . . . . . . . . .
List of Figures AFG3000 Series Arbitrary/Functio n Generators Reference Manual v List of Figures Figure 1-1: Dual-channel model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 Figure 1-2: Fron t panel controls . . . .
List of Figures vi AFG3000 Series Arbitrary/Function Generators Reference Manual Figure 4-5: Questionable Condition Re gister (QCR) . . . . . . . . . . . . . . . . . . . . . . . 4-8 Figure 4-6: Ev ent Status Enable Register (ESER) . . . . . . . . . . .
List of T ables AFG3000 Series Arbitrary/Functio n Generators Reference Manual vii List of T ables Table 2-1: Sine/Square Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 Table 2-2: Ramp Menu . . . . . . . .
List of T ables viii AFG3000 Series Arbitrary/Function Generators Reference Manual Table A-1: Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1 Table A-2: Standard accessori es . . . . . . .
AFG3000 Series Arbitrary/Functio n Generators Reference Manual ix General Safety Summary Re view the fol lowing safety precautions to av oid injury and pre vent damage to this product or an y products conn ected to it . T o av oid potential hazards, use this product only as specif ied.
General Safety Summary x AFG3000 Series Arbitrary/Function Generators Reference Manual Symbols and T erms T erms in this Manual. These terms may appear in this manual: T erms on the Product. These terms may appear on the product: D ANGER indicates an injury hazard immediately acces sible as you read the marking.
AFG3000 Series Arbitrary/Functio n Generators Reference Manual xi Preface This manual provides operating in formation for the AFG3000 S eries Arbitrary/Function Genera tors. The manual consists of the follo wing sections: Operating Basics co vers operating principles of the instrument.
Preface xii AFG3000 Series Arbitrary/Function Generators Reference Manual AFG3000 Series Service Man ual. A serv ice manual is a v ailable as an optional accessory . The service manual includes pro cedure s to service th e instrument to the module le vel.
Operating Basics.
.
AFG3000 Series Arbitrary/Functio n Generators Reference Manual 1-1 Operating Basics The AFG3000 Series Arbitra ry/Function Genera tors front panel is divided into easy to use functional areas. This section provides you with a quick ov ervie w of the controls.
Operating Basics 1-2 AFG3000 Series Arbitrary/Function Generators Reference Manual Fr ont P anel Contr ols This section introduces you to the front panel controls of the instrument and provides a brief ov erview on ho w to use the front panel key controls.
Operating Basics AFG3000 Series Arbitrary/Functio n Generators Reference Manual 1-3 Action Buttons The Po wer (not sh o wn in Figure 1-2), Upper Menu, T op Menu, V ie w , and Manual T rigger b uttons are called action b uttons. When you push these act ion butt ons, it will cause an action.
Operating Basics 1-4 AFG3000 Series Arbitrary/Function Generators Reference Manual View Format 1. Fi gure 1-3 is a single channel parameter and grap h setup display . In this vie w , Channel 1 is selected with th e Channel Select b utton. When Channel 2 is selected, the parameters and graph for Channel 2 will be display ed in this view .
Operating Basics AFG3000 Series Arbitrary/Functio n Generators Reference Manual 1-5 View Format 3. Fi gure 1-5 is a channel compare vie w . In this vie w , Channel 1 is selected with the Channel Select button. Figure 1-5: W a veform parameter comparison (CH1 selec ted) In Figure 1-6, Channel 2 is select ed with the Channel Select button.
Operating Basics 1-6 AFG3000 Series Arbitrary/Function Generators Reference Manual Other Action buttons. The Enter b utton and the fol lowi ng related b uttons are also classified as Action b uttons. Enter button. The Enter b utton causes a numeric input to be updated.
Operating Basics AFG3000 Series Arbitrary/Functio n Generators Reference Manual 1-7 State Buttons The Channel Select, CH1/CH2 Output an d Run Mode bu ttons are called Stat e buttons. Channel Sele ct button. The Channel Select bu tton directly controls the display , toggling between the two channels.
Operating Basics 1-8 AFG3000 Series Arbitrary/Function Generators Reference Manual Select the Run Mode Menu bezel b utton from the def ault screen (see page 1-14) to display the Run Mode menus. The Conti nuous mode is selected in Figure 1-7. If you select Modulation, Sweep, or Burst as the Run Mode, the correspondin g bezel menu is high lighted.
Operating Basics AFG3000 Series Arbitrary/Functio n Generators Reference Manual 1-9 Shortcut Buttons The follo wing six b uttons are called Shortcut b uttons and are provided as shortcuts for experienced users. Y ou can push this button whi le vie wing any of the display types.
Operating Basics 1-10 AFG3000 Series Arbitrary/Function Generators Reference Manual BNC Connectors Refer to Figu re 1-2 on page 1-2 for th e locations of the front pan el BNC connec- tors. CH1 Output. This BNC connector will output the Channel 1 signal.
Operating Basics AFG3000 Series Arbitrary/Functio n Generators Reference Manual 1-11 Displa y Area and Screen Interface Figure 1-8 sho ws the main areas of the instrument display . Figure 1-8: Screen interface Main Displa y Area Pushing the front-panel Vie w button changes the view fo rmat of the main display area.
Operating Basics 1-12 AFG3000 Series Arbitrary/Function Generators Reference Manual Level Meter . Amplitude le v el is displayed. T o pr otect your DUT (de vice under test), use the Output Menu to set the limit v alues for high le v el and low le v el.
Operating Basics AFG3000 Series Arbitrary/Functio n Generators Reference Manual 1-13 Bezel Menu Displa y Area When you push a front panel b utton, the in strument displays the co rresponding menu on the right side of the screen.
Operating Basics 1-14 AFG3000 Series Arbitrary/Function Generators Reference Manual W avef orm P arameter s and Numeric Input This section explains ho w to set or ch ange the w av eform parameters of the arbitrary/function generator using the front-p anel controls or bezel menu selection.
Operating Basics AFG3000 Series Arbitrary/Functio n Generators Reference Manual 1-15 Numeric Input If you want to change the frequency v alue, push the Frequency bezel b utton. The v alue of Freq in main display area chan ges to “selected status”.
Operating Basics 1-16 AFG3000 Series Arbitrary/Function Generators Reference Manual Y ou can also change the value with the fro nt-panel numeric ke y-pad. Entering an y v alue from the numeric key-pad will automa tically change the bezel menu to Units.
Operating Basics AFG3000 Series Arbitrary/Functio n Generators Reference Manual 1-17 Changing P arameters Using the Shortcut Buttons The shortcut buttons are pro vided for e xpe rienced users. The butto ns allo w you to select a setup parameter without using an y bezel menu selection.
Operating Basics 1-18 AFG3000 Series Arbitrary/Function Generators Reference Manual Y ou can no w change the frequen cy v alue. If you pu sh the Fr equency/Period shortcut button ag ain, the activ e paramete r will change to Period.
Operating Basics AFG3000 Series Arbitrary/Functio n Generators Reference Manual 1-19 Rear P anel Figure 1-21 sho ws the locations of th e instrument rear panel connecto rs.
Operating Basics 1-20 AFG3000 Series Arbitrary/Function Generators Reference Manual USB. The USB connector is used to connect a USB controller . LAN. This connector is used to connect the arbitrary/function generator to a network. Connect a 10B ASE-T or 100BASE-T cable here.
Ref erence.
.
AFG3000 Series Arbitrary/Functio n Generators Reference Manual 2-1 Ref erence This section describes the menus associated with each front-panel menu b utton or control. Menu System The user interface of the AFG3000 Seri es Arbitrary/Function Generators was designed for easy access to specialize d functions through the menu structure.
Reference 2-2 AFG3000 Series Arbitrary/Function Generators Reference Manual Menu Structure This section describes the menus and op erating details associated with each front-panel menu b utton. Sine/Square Menu, page 2-3 Ramp Menu, page 2-4 Pulse Menu, page 2-4 Arb Menu, page 2-5 More.
Reference AFG3000 Series Arbitrary/Functio n Generators Reference Manual 2-3 Sine/Square Menu T able 2-1 shows the Sine and Squar e menu. T able 2-1: Sine/Square Men u First Le vel Second Level Thir d Level Description F requency/P er iod/ Phase Menu F requency Selects Frequency as a parameter to be change d.
Reference 2-4 AFG3000 Series Arbitrary/Function Generators Reference Manual Ramp Menu T able 2-2 shows the Ramp menu. Pulse Menu T able 2-3 shows the Pulse menu. T able 2-2: Ramp Men u First Le vel Second Level Description Ramp P ar ameter Menu Symmetr y Sets the Ramp wa v ef orm symmetr y to your desired v alue.
Reference AFG3000 Series Arbitrary/Functio n Generators Reference Manual 2-5 Arb Menu The arbitrary/function generator can outpu t a user-def ined wa veform that is stored in the internal memory , Edit Memory , or a USB memory . T able 2-4 shows the Arb menu.
Reference 2-6 AFG3000 Series Arbitrary/Function Generators Reference Manual More ... Menu T able 2-5 sho ws the Mor e... menu. T able 2-5: More Men u First Le vel Second Level Description More W a vef.
Reference AFG3000 Series Arbitrary/Functio n Generators Reference Manual 2-7 Modulation P arameter Menu T able 2-6 sho ws the Modu lation Parameter Menu.
Reference 2-8 AFG3000 Series Arbitrary/Function Generators Reference Manual Phase Modulation. Phase modulation is similar to FM (F requency modulation), b ut in PM, the phase of the carrier wa veform is va ried by the amplitude of the modu- lating wa veform.
Reference AFG3000 Series Arbitrary/Functio n Generators Reference Manual 2-9 Sweep P arameter Menu T able 2-7 shows the Sweep Parameter Menu. The sweep function outputs a wa veform with the output signal frequency v arying linearly or logarithmically .
Reference 2-10 AFG3000 Series Arbitrary/Function Generators Reference Manual When sweep is taking place, the frequency sweeps from start frequenc y to stop fre- quency .
Reference AFG3000 Series Arbitrary/Functio n Generators Reference Manual 2-11 Burst P arameter Men u T able 2-8 shows the Burst P arameter Menu. T riggered Bur st Mode. When a trigger ev ent occurs in b urst mode, the wav eform is output for the number of cycles specif ied by the Burst P arameter Menu.
Reference 2-12 AFG3000 Series Arbitrary/Function Generators Reference Manual Output Menu T able 2-9 show s the Output Menu. T o access the Output menu, push the front-panel T op Menu butto n, and then push the b ottom bezel b utton. T able 2-9: Output Men u First Le vel Second Level Description Load Impedance 50 Ω Option buttons .
Reference AFG3000 Series Arbitrary/Functio n Generators Reference Manual 2-13 Save/Recall Men u The Save and Recall menus store or recall arbitrar y/function ge nerator setups.
Reference 2-14 AFG3000 Series Arbitrary/Function Generators Reference Manual Edit Menu The Edit menu is used to create or edit user -defined w av eforms and to import or export w a veforms. T o output a user-def ined wa veform, wa veform data must be created in the Edit Memory and then st ored in the internal or a USB memory .
Reference AFG3000 Series Arbitrary/Functio n Generators Reference Manual 2-15 P aste at Beginning Memor y Internal USB Selects a memor y type (Inter nal or USB). P aste P astes a w av ef orm at the beginning of the current wa v eform. (blank) Change Director y Opens a director y .
Reference 2-16 AFG3000 Series Arbitrary/Function Generators Reference Manual Number of P oin ts. This bezel menu sets the number of points of the wa veform to be created or the length of Edit Memory .
Reference AFG3000 Series Arbitrary/Functio n Generators Reference Manual 2-17 New . Pushing the New bezel b utton will display a st andard wa v eform selection submenu. Y ou can select a standard wa ve form from fi v e wa veform types (Sine, Square, Pulse, Ramp, and Nois e).
Reference 2-18 AFG3000 Series Arbitrary/Function Generators Reference Manual Using the Cursor s. Y ou can use cursors to edit a wav eform. T o use cursors, select the Operations submenu in the Edit menu.
Reference AFG3000 Series Arbitrary/Functio n Generators Reference Manual 2-19 Line (Line Edit). The Line edits by linearly interpola ting from a specified point in the wa veform currently edited to another specified point as shown in Figure 2-5. Figure 2-5: Line Edi t example Data (Edit b y Data P oint).
Reference 2-20 AFG3000 Series Arbitrary/Function Generators Reference Manual Cut (Cut by Data P oints). The Cut deletes an area between specified points in the wa veform. When Cut is selected, two v alues can be input (From X1 and T o X2). See Figure 2-7.
Reference AFG3000 Series Arbitrary/Functio n Generators Reference Manual 2-21 P aste at Beginning. The Paste at Beginning inserts the contents of the user wa v e- form memory (User1, User2, User3, or User4), USB memory , or the current contents of Edit Memory at the be ginning of the wa veform that is currently being edited.
Reference 2-22 AFG3000 Series Arbitrary/Function Generators Reference Manual P aste at End. The Pas te a t En d appends the contents of the user wav eform memory (User1, User2, User3, or User4), USB memory , or the current contents of edit memory at the end of the wave form currently being edited.
Reference AFG3000 Series Arbitrary/Functio n Generators Reference Manual 2-23 Utility Menu The Utility menu prov ides access to utilities used by the arbitrary/function gener- ator such as language selection, instru ment diagnostics, and user preferences.
Reference 2-24 AFG3000 Series Arbitrary/Function Generators Reference Manual System T rigger Out T rigger Sync Select Tr i g g e r to generate the trigger signal for the oscilloscope. Select Sync to synchronize m ultiple AFG3000 series instr uments. Clock Ref Internal Exter nal Select Internal to accept the internal reference clock.
Reference AFG3000 Series Arbitrary/Functio n Generators Reference Manual 2-25 Connecting to a GPIB Netw ork. The GPIB Interface can be used for remotely con- trolling the arbitrary/function generator fro m an external device (such as a PC). Refer to Syntax an d Commands on page 3-1 for information about remote control commands.
Reference 2-26 AFG3000 Series Arbitrary/Function Generators Reference Manual Synchr onous O peration. By synchronizing multiple ar bitrary/function generators, you can configure the multichannel arbitra ry/function generator.
Reference AFG3000 Series Arbitrary/Functio n Generators Reference Manual 2-27 Back up/Restore. The Backup function is prov ided for copying the current arbi- trary/function generator information (ins trument setups or user -def ined wa ve- forms) to a USB memory with a single bu tton push.
Reference 2-28 AFG3000 Series Arbitrary/Function Generators Reference Manual File Operations This section describes the ba sic f ile operations such as bro wsing f iles and sa ving or recalling the instrument setups or wa ve form data.
Reference AFG3000 Series Arbitrary/Functio n Generators Reference Manual 2-29 Bro wsing W a vef orm Files using Edit Menu. Y ou can also bro wse through w av e- forms using the Edit Menu. Select a f ile you want to edit and then push the Read bezel button.
Reference 2-30 AFG3000 Series Arbitrary/Function Generators Reference Manual Entering a File Name. When you select Write As from the Write to... submenu, the character entry box is displayed as sho wn in Figure 2-11. Figure 2-11: Write As - Character entry box English alphabet characters are displayed be lo w the file name box.
Reference AFG3000 Series Arbitrary/Functio n Generators Reference Manual 2-31 Bro wsing Instrument Setup Files T o bro wse instrument setup f iles in the in ternal memory or in a USB memory , push the front-panel Recall button, and then push the Memory bezel b utton to specify Internal or USB as a memo ry type.
Reference 2-32 AFG3000 Series Arbitrary/Function Generators Reference Manual Entering a File Name. When you select Save As , the f ile name box is displayed as sho wn in Figure 2-13. Figure 2-13: Save As - Character entry box English alphabet characters are displayed be lo w the file name box.
Syntax and Commands.
.
AFG3000 Series Arbitrary/Functio n Generators Reference Manual 3-1 Syntax and Commands This section provides th e follo wing information: Command Syntax defines the command syntax and processing con ventions. Command Groups describes comman d groups wh ich lists the commands by function.
Syntax and Co mmands 3-2 AFG3000 Series Arbitrary/Function Generators Reference Manual Command and Query Structure Commands consist of set commands and qu ery commands (usually simply called commands and queries). Commands chan ge instrument settings or perform a specific action.
Syntax and Command s AFG3000 Series Arbitrary/Functio n Generators Reference Manual 3-3 Figure 3-1 shows the f i ve command message elements. Figure 3-1: Command messa ge elements Commands. Commands cause the instrument to perform a specific function or change one of its settings.
Syntax and Co mmands 3-4 AFG3000 Series Arbitrary/Function Generators Reference Manual Command Entry Follo w these general rules when entering commands: Enter commands in upper or lower case. Y ou can precede any command with white space characters.
Syntax and Command s AFG3000 Series Arbitrary/Functio n Generators Reference Manual 3-5 Creating Commands SCPI com mands are created by stringing toge ther the nodes of a subs ystem hier- archy and separating each no de by a colon. In Figure 3-2, TR IGger is the root node and SEQuence , SLOPe , SOURce , and TI Mer are lo wer le vel nodes.
Syntax and Co mmands 3-6 AFG3000 Series Arbitrary/Function Generators Reference Manual Special Characters The Line Feed (LF) character or the New Line (NL) character (ASCII 10), and all characters in the range of ASCII 127-255 are defined as special characters.
Syntax and Command s AFG3000 Series Arbitrary/Functio n Generators Reference Manual 3-7 Chaining Commands and Queries Y ou can chain sev eral commands or querie s together into a single message.
Syntax and Co mmands 3-8 AFG3000 Series Arbitrary/Function Generators Reference Manual General Rules for Using SCPI commands The following are three general rules for using SCPI commands, queries, and.
Syntax and Command s AFG3000 Series Arbitrary/Functio n Generators Reference Manual 3-9 Command Groups This section lists the co mmands org anized by functio nal group. The Com mand Descriptions section, starting on page 3-15, lists all comman ds alphabetically .
Syntax and Co mmands 3-10 AFG3000 Series Arbitrary/Function Generators Reference Manual Mass Memory Commands. Mass Memory comma nds let you change mass memory attributes. T able 3-8 lists and describes Mass Memory commands. Output Commands. Output commands let you set output attributes.
Syntax and Command s AFG3000 Series Arbitrary/Functio n Generators Reference Manual 3-11 [SOURce[1|2]]:BURSt [:ST A T e] Set/quer y burst mode status [SOURce[1|2]]:COMBine:FEED Set/query internal nois.
Syntax and Co mmands 3-12 AFG3000 Series Arbitrary/Function Generators Reference Manual Status Commands. Status commands let you determin e the status of the instrument.
Syntax and Command s AFG3000 Series Arbitrary/Functio n Generators Reference Manual 3-13 System Commands. System commands let you control miscellaneou s instrument functions. T able 3-12 lists and describes System command s. Synchr onization Command s.
Syntax and Co mmands 3-14 AFG3000 Series Arbitrary/Function Generators Reference Manual T race Comma nds. T race commands let you set the edit memory and user wav eform memory . T able 3-14 lists an d describes T race commands. Tr i g g e r C o m m a n d s .
Syntax and Command s AFG3000 Series Arbitrary/Functio n Generators Reference Manual 3-15 Command Descriptions Commands either set or query instrument v alues.
Syntax and Co mmands 3-16 AFG3000 Series Arbitrary/Function Generators Reference Manual AFGContr ol:CSCop y (No Query Form) This command copies setu p parameters for one chan nel to another channel. If your arbitrary/function generat or is a si ngle-channel model, th is command is not supported.
Syntax and Command s AFG3000 Series Arbitrary/Functio n Generators Reference Manual 3-17 CALibration[:ALL] The CALibration[: ALL] command pe rforms an internal calibration. The CALibration[ :ALL]? command performs an intern al calibration and returns 0 (Pass) or a calibration error code.
Syntax and Co mmands 3-18 AFG3000 Series Arbitrary/Function Generators Reference Manual DIA Gnostic[:ALL] The DIAGn ostic[:ALL] command performs a self-test.
Syntax and Command s AFG3000 Series Arbitrary/Functio n Generators Reference Manual 3-19 DISPla y:CONT rast This command sets or queries th e contrast of the LCD display .
Syntax and Co mmands 3-20 AFG3000 Series Arbitrary/Function Generators Reference Manual DISPla y[:WINDo w]:TEXT[:D A T A] The DISPlay[:WINDo w]:TEXT[:DA TA] command displays a text message on the instrument screen. The DISPlay[:WIND ow]:TEXT[:D ATA]? command returns a text string currently displayed on the instrument screen.
Syntax and Command s AFG3000 Series Arbitrary/Functio n Generators Reference Manual 3-21 *ESE This command sets or queries the bits in the Ev ent Status Enable Register (ESER) used in the status and e ven ts reporting system of the arbitrary/fun ction generator.
Syntax and Co mmands 3-22 AFG3000 Series Arbitrary/Function Generators Reference Manual *ESR? This query-only comman d re turns the contents of the Standard Event Status Register (SESR) used in the status e v ents reporting system in the arbitrary/function generator.
Syntax and Command s AFG3000 Series Arbitrary/Functio n Generators Reference Manual 3-23 MEMory:ST A T e:V ALid? This query-only comman d returns the av ailability of a setup memory . Gr oup Memory Syntax MEMory:STA Te:VALid? {0 |1|2|3|4} Arguments 0, 1, 2, 3, or 4 specif ies the location of setup memory .
Syntax and Co mmands 3-24 AFG3000 Series Arbitrary/Function Generators Reference Manual MEMory:ST A T e:LOCK This command sets or queries whether to lock the specified setup memory . If you lock a setup memo ry , you cannot ov er write or delete the setup f ile.
Syntax and Command s AFG3000 Series Arbitrary/Functio n Generators Reference Manual 3-25 MEMory:ST A T e:RECall:A UT o This command sets or queries whether to enable the automatic recall of last setup memory when po wered-on.
Syntax and Co mmands 3-26 AFG3000 Series Arbitrary/Function Generators Reference Manual MMEMory:CA T a log? This query-only comman d returns the current state of the mass storag e system (USB memory).
Syntax and Command s AFG3000 Series Arbitrary/Functio n Generators Reference Manual 3-27 MMEMory:CDIRectory This command changes the cu rrent working directory in th e mass storag e system.
Syntax and Co mmands 3-28 AFG3000 Series Arbitrary/Function Generators Reference Manual MMEMory:LO AD:ST A T e (No Quer y Form) This command copies a setup file in the mass storage system to an internal setup memory . If a specified internal set up memo ry is locked, this command causes an error .
Syntax and Command s AFG3000 Series Arbitrary/Functio n Generators Reference Manual 3-29 MMEMory:LOCK[:ST A T e] This command sets or queries whether to lo ck a file or dire ctory in the mass sto rage system. If you lock a file or di rector y , you cannot ov erwrite or delete it.
Syntax and Co mmands 3-30 AFG3000 Series Arbitrary/Function Generators Reference Manual MMEMory:ST ORe:ST A T e (No Query Form) This command copies a setup file in the setup memory to a specified f ile in the mass storage system. If the specif ied file in the mass storage system is locked, this command causes an error .
Syntax and Command s AFG3000 Series Arbitrary/Functio n Generators Reference Manual 3-31 *OPC This command generates the operation complete messag e by setting bit 0 in the Standard Event Status Re gister (SESR) wh en al l pending comma nds that generate an OPC message are complete.
Syntax and Co mmands 3-32 AFG3000 Series Arbitrary/Function Generators Reference Manual OUTPut[1|2]:IMP edance The OUTPut:IM Pedance command sets the output load impedance for the specif ied channel. The specified v alue is used for amplitude, of fset, and high/lo w le v el settings.
Syntax and Command s AFG3000 Series Arbitrary/Functio n Generators Reference Manual 3-33 OUTPut[1|2]:POLarity This command in ve rts a specified output w av e form relati ve to the of fset lev el. The query command returns the polar ity for the specif ied channel.
Syntax and Co mmands 3-34 AFG3000 Series Arbitrary/Function Generators Reference Manual OUTPut:TRIGger:MODE This command sets or queries the mode (tri gger or sync) for T rigger Output signal.
Syntax and Command s AFG3000 Series Arbitrary/Functio n Generators Reference Manual 3-35 *PSC This comman d sets and querie s the po wer -on status flag that controls the automatic po wer-on ex ecution of SRER and ESER. Wh en *PSC is true, SRER and ESER are set to 0 at power -on.
Syntax and Co mmands 3-36 AFG3000 Series Arbitrary/Function Generators Reference Manual *RST (No Query Form) This command resets the instrument to the factory default se ttings. This command is equiv alent to pushing the Default button on the front pane l.
Syntax and Command s AFG3000 Series Arbitrary/Functio n Generators Reference Manual 3-37 [SOURce[1|2]]:AM[:DEPTh] This command sets or queries the modulation depth of AM modulation for the specified channel.
Syntax and Co mmands 3-38 AFG3000 Series Arbitrary/Function Generators Reference Manual [SOURce[1|2]]:AM:INT e rnal:FREQuency This command sets or queries the intern al modulation freq uency of AM modula- tion for the specif ied channel. Y ou can use this comm and only when the internal modulation source is selected.
Syntax and Command s AFG3000 Series Arbitrary/Functio n Generators Reference Manual 3-39 [SOURce[1|2]]:AM:INT e rnal:FUNCtion This command sets or queries the modula ting w av eform of AM modulation for the specified channel. Y ou ca n use this comm and only when the internal modulation source is s elected.
Syntax and Co mmands 3-40 AFG3000 Series Arbitrary/Function Generators Reference Manual [SOURce[1|2]]:AM:INT e rnal:FUNCtion:EFILe This command sets or queries an EFILe name used as a modulating wa v eform for AM modulation. A f ile name must be specif ied in the mass storage system.
Syntax and Command s AFG3000 Series Arbitrary/Functio n Generators Reference Manual 3-41 [SOURce[1|2]]:AM:ST A T e This command enables or disables AM mo dulation for the spec ified channel.
Syntax and Co mmands 3-42 AFG3000 Series Arbitrary/Function Generators Reference Manual [SOURce[1|2]]:BURSt:NCYCles This command sets or queries t he number of c ycles (burst count ) to be output in burst mode for the specified channel. Th e query command returns 9.
Syntax and Command s AFG3000 Series Arbitrary/Functio n Generators Reference Manual 3-43 [SOURce[1|2]]:BURSt[:ST A T e] This command enables or disables the bu rst mode for the spec ified channel.
Syntax and Co mmands 3-44 AFG3000 Series Arbitrary/Function Generators Reference Manual [SOURce[1|2]]:BURSt:TDELa y This command sets or queries delay tim e in the burst mode for the specifi ed channel. It specifies a time delay between the trigger and the signal output.
Syntax and Command s AFG3000 Series Arbitrary/Functio n Generators Reference Manual 3-45 [SOURce[1|2]]:COMBine:FEED This command sets or queries whether to add the internal noise or an e xternal signal to an output sign al for the specif ied channel.
Syntax and Co mmands 3-46 AFG3000 Series Arbitrary/Function Generators Reference Manual [SOURce[1|2]]:FM[:DEViation] This command sets or queries the peak frequency de viation of FM modulation for the specif ied channel. The setting range of frequency de viation depends on the wa veform selected as the carrier .
Syntax and Command s AFG3000 Series Arbitrary/Functio n Generators Reference Manual 3-47 [SOURce[1|2]]:FM:INT ernal:FUNCtion This command sets or queries the modula ting wav eform of FM modulation for the specified channel. Y ou ca n use this comm and only when the internal modulation source is s elected.
Syntax and Co mmands 3-48 AFG3000 Series Arbitrary/Function Generators Reference Manual [SOURce[1|2]]:FM:INT e rnal:FUNCti on:EFILe This command sets or queries an EFILe name used as a modulating wa v eform for FM modulation. A f ile name must be sp ecif ied in the mass storage system.
Syntax and Command s AFG3000 Series Arbitrary/Functio n Generators Reference Manual 3-49 [SOURce[1|2]]:FM:ST A T e This command enables or disables FM mod ulation.
Syntax and Co mmands 3-50 AFG3000 Series Arbitrary/Function Generators Reference Manual [SOURce[1|2]]:FREQuency:CONCurrent[:ST A T e] This command enables or disables the fu nction to copy the frequenc y (or period) of one chan nel to another c hannel.
Syntax and Command s AFG3000 Series Arbitrary/Functio n Generators Reference Manual 3-51 [SOURce[1|2]]:FREQuency[:CW|:FIXed] This command sets or querie s the frequency of output wav eform for the specif ied channel. This command is av ailable when the Run Mode is s et to other than Sweep.
Syntax and Co mmands 3-52 AFG3000 Series Arbitrary/Function Generators Reference Manual [SOURce[1|2]]:FREQuency:MODE This command sets or queries the frequency sweep state.
Syntax and Command s AFG3000 Series Arbitrary/Functio n Generators Reference Manual 3-53 [SOURce[1|2]]:FREQuency:SP AN This command sets or queries the span of frequency sweep for the specified channel. This command is always used with the [SOURce[1| 2]]:FREQuenc y:CENTer command.
Syntax and Co mmands 3-54 AFG3000 Series Arbitrary/Function Generators Reference Manual [SOURce[1|2]]:FREQuency:ST ARt This command sets or queries the start frequency of sweep for the specif ied channel. This command is always used with the [SOURce[1| 2]]:FREQuenc y:STOP command.
Syntax and Command s AFG3000 Series Arbitrary/Functio n Generators Reference Manual 3-55 [SOURce[1|2]]:FREQuency:ST OP This command sets or queries the start frequency of sweep for the specif ied channel. This command is always used with the [SOURce[1| 2]]:FREQuenc y:STARt command.
Syntax and Co mmands 3-56 AFG3000 Series Arbitrary/Function Generators Reference Manual [SOURce[1|2]]:FSKe y[:FREQuenc y] This command sets or queries the hop fre quenc y of FSK modulation for the spec- ified channel.
Syntax and Command s AFG3000 Series Arbitrary/Functio n Generators Reference Manual 3-57 [SOURce[1|2]]:FSKe y:SOURce This command sets or queries the source of modulation signal of FSK modulation for the specified channel.
Syntax and Co mmands 3-58 AFG3000 Series Arbitrary/Function Generators Reference Manual [SOURce[1|2]]:FUNCtion:EFILe This command sets or queries an EFILe na me used as an output wa veform. A f ile name must be specified in the mass storage system. This comm and causes an error if there is no f ile in the mass storage.
Syntax and Command s AFG3000 Series Arbitrary/Functio n Generators Reference Manual 3-59 [SOURce[1|2]]:FUNCtion[:SHAP e] This command sets or queries the shape of the output wav eform. When the speci- fied user memory is deleted, this command causes an error if you select the user memory .
Syntax and Co mmands 3-60 AFG3000 Series Arbitrary/Function Generators Reference Manual EFILe EFILe is specif ied as an output wa v eform. Returns SIN|SQU|PU LS|RAMP|PRN| DC|SINC|GAU S|LOR|ERIS|ED EC|.
Syntax and Command s AFG3000 Series Arbitrary/Functio n Generators Reference Manual 3-61 [SOURce[1|2]]:PHASe:INITiate (No Query Form) This command synchron izes the phase of CH 1 and CH 2 output wav eforms. The arbitrary/function generator performs the same operation if you sp ecify either SOURce1 or SOURce2.
Syntax and Co mmands 3-62 AFG3000 Series Arbitrary/Function Generators Reference Manual [SOURce[1|2]]:PM:INT e rnal:FREQuency This command se ts or querie s the internal modulation frequency of PM modulation for the specified channel. Y ou can use this command only when the internal modu- lation source is selected.
Syntax and Command s AFG3000 Series Arbitrary/Functio n Generators Reference Manual 3-63 [SOURce[1|2]]:PM:INT e rnal:FUNCtion This command sets or queries the modula ting wav eform of PM modulation for the specified channel. Y ou ca n use this comm and only when the internal modulation source is s elected.
Syntax and Co mmands 3-64 AFG3000 Series Arbitrary/Function Generators Reference Manual [SOURce[1|2]]:PM:INT e rnal:FUNCtion:EFILe This command sets or queries an EFILe name used as a modulating wa v eform for PM modulation. A f ile name must be sp ecif ied in the mass storage system.
Syntax and Command s AFG3000 Series Arbitrary/Functio n Generators Reference Manual 3-65 [SOURce[1|2]]:PM:ST A T e This command enables or disables PM mod ulation. The query command returns the state of PM modulation.Y ou can sele ct a sine, square, ramp, or a rbitrary wav e- form for the carrier wa ve form.
Syntax and Co mmands 3-66 AFG3000 Series Arbitrary/Function Generators Reference Manual SOURce<3|4>:PO W er[:LEV el ][:IMMediate][:AMPLitude] This command sets or queries the internal noise le v el which applies to the output signal for the specifi ed channel.
Syntax and Command s AFG3000 Series Arbitrary/Functio n Generators Reference Manual 3-67 [SOURce[1|2]]:PULSe:DCYCle This command sets or queries the duty cy cle of the pulse w av eform for the speci- fied channel. The setting range is 0.1% to 99.9% in increments of 0.
Syntax and Co mmands 3-68 AFG3000 Series Arbitrary/Function Generators Reference Manual [SOURce[1|2]]:PULSe:DELa y This command sets or queries the lead de lay of the pulse w av eform for the speci- fied channel.
Syntax and Command s AFG3000 Series Arbitrary/Functio n Generators Reference Manual 3-69 [SOURce[1|2]]:PULSe:PERiod This command sets or queries the period for pulse wa v eform.
Syntax and Co mmands 3-70 AFG3000 Series Arbitrary/Function Generators Reference Manual [SOURce[1|2]]:PULSe :TRANsition:TRAiling This command sets or queries the tr ailing edge time of pulse wa v eform.
Syntax and Command s AFG3000 Series Arbitrary/Functio n Generators Reference Manual 3-71 [SOURce[1|2]]:PULSe:WIDTh This command sets or queries the pu lse width for the specified channel. Pulse W idth = Period × Duty Cycle / 100 The pulse width must b e less than the period.
Syntax and Co mmands 3-72 AFG3000 Series Arbitrary/Function Generators Reference Manual [SOURce[1|2]]:PWM:INT e rnal:FREQuency This command sets or qu er ies the internal modulation frequency of PWM modula- tion for the specif ied channel. Y ou can use this comm and only when the internal modulation source is selected.
Syntax and Command s AFG3000 Series Arbitrary/Functio n Generators Reference Manual 3-73 [SOURce[1|2]]:PWM:INT e rnal:FUNCtion This command sets or queries the modulating wa ve form of PWM modulation for the specified chan nel. Y ou can use this command on ly when the internal modula- tion source is selected.
Syntax and Co mmands 3-74 AFG3000 Series Arbitrary/Function Generators Reference Manual [SOURce[1|2]]:PWM:IN T ernal:FUNCtion:EFILe This command sets or queries an EFILe name used as a modulating wa v eform for PWM modulation . A file name must be spec if ied in the mass st orage syst em.
Syntax and Command s AFG3000 Series Arbitrary/Functio n Generators Reference Manual 3-75 [SOURce[1|2]]:PWM:ST A T e This command ena bles or disables PWM modu lation. The query co mmand returns the state of PWM modulation. Y ou can sel ect only pulse wa veform as a carrier wa veform for PWM.
Syntax and Co mmands 3-76 AFG3000 Series Arbitrary/Function Generators Reference Manual [SOURce[1|2]]:PWM[:DEViation]:DCYCle This command sets or queries the PWM de viation in percent for the specif ied channel.
Syntax and Command s AFG3000 Series Arbitrary/Functio n Generators Reference Manual 3-77 [SOURce]:R OSCillator:SOURce This command sets the reference cloc k to either internal or external.
Syntax and Co mmands 3-78 AFG3000 Series Arbitrary/Function Generators Reference Manual [SOURce[1|2]]:SWEep:MODE The [SOURce [1|2]]:SWEep: MODE command selects auto or manual for the sweep mode for the spec if ied channel. The query command returns the swee p mode for the specified channel.
Syntax and Command s AFG3000 Series Arbitrary/Functio n Generators Reference Manual 3-79 [SOURce[1|2]]:SWEep:RT IMe This command sets or queries the sweep return time. Return time represents the amount of time from stop frequency through start fre quency .
Syntax and Co mmands 3-80 AFG3000 Series Arbitrary/Function Generators Reference Manual [SOURce[1|2]]:SWEep:TIME This command sets or queries the sweep time for the sweep for the specified channel. The sweep time does not include hold time and return time.
Syntax and Command s AFG3000 Series Arbitrary/Functio n Generators Reference Manual 3-81 [SOURce[1|2]]:V OL T age:CONCurrent[:ST A T e] This command enables or disables the fu nction to copy the v oltage le vel of one channel to another channel.
Syntax and Co mmands 3-82 AFG3000 Series Arbitrary/Function Generators Reference Manual [SOURce[1|2]]:V OL T age[:LEV el][:IMMediate]:HIGH This command sets or queries the high le vel of output amplitude for the specif ied channel.
Syntax and Command s AFG3000 Series Arbitrary/Functio n Generators Reference Manual 3-83 [SOURce[1|2]]:V OL T age[:LEV el][:IMMediate]:LO W This command sets or queries the lo w lev e l of output amplitude for the specif ied channel.
Syntax and Co mmands 3-84 AFG3000 Series Arbitrary/Function Generators Reference Manual [SOURce[1|2]]:V OL T age[:LEV el][:IMMediate]:OFFSet This command sets or queries the of fset le vel for the specif ied chan nel.
Syntax and Command s AFG3000 Series Arbitrary/Functio n Generators Reference Manual 3-85 [SOURce[1|2]]:V OL T age[:LEV el][:IMMediate][:AMPLitude] This command sets or queries the output amplitude for the sp ecified channel.
Syntax and Co mmands 3-86 AFG3000 Series Arbitrary/Function Generators Reference Manual [SOURce[1|2]]:V OL T age:LIMit:HIGH This command sets or queries the higher limit of the output ampli tude high le v el for the specified channel.
Syntax and Command s AFG3000 Series Arbitrary/Functio n Generators Reference Manual 3-87 [SOURce[1|2]]:V OL T age:LIMit:LO W This command sets or queries the lower lim it of the output amplitude lo w le vel for the specified channe l.
Syntax and Co mmands 3-88 AFG3000 Series Arbitrary/Function Generators Reference Manual [SOURce[1|2]]:V OL T age:UNIT This command sets or queries the units of output amplitude for the specified channel. This co mmand does not af fect th e of fset, High le vel, or Lo w le ve l of output.
Syntax and Command s AFG3000 Series Arbitrary/Functio n Generators Reference Manual 3-89 *SRE This command sets and queries the bits in the Service Request Enable Re gister (SRER).
Syntax and Co mmands 3-90 AFG3000 Series Arbitrary/Function Generators Reference Manual ST A T us:OPERation:CONDition? This query-only command returns the contents of the Operation Condition Register .
Syntax and Command s AFG3000 Series Arbitrary/Functio n Generators Reference Manual 3-91 ST A T us:OPERation[:EVENt]? This query-only comman d re turns the v alue in the Operation Event Register and clears the Operation Event Re gister .
Syntax and Co mmands 3-92 AFG3000 Series Arbitrary/Function Generators Reference Manual ST A T us:QUEStionab le:CONDition? This query-only command returns the contents of the Questionable Condition Register .
Syntax and Command s AFG3000 Series Arbitrary/Functio n Generators Reference Manual 3-93 ST A T us:QUEStionab le[:EVENt]? This query-only command returns the v alue in the Questiona ble Ev ent Regi ster and clears the Questionable Event Register .
Syntax and Co mmands 3-94 AFG3000 Series Arbitrary/Function Generators Reference Manual SYST em:BEEP er[:IMMediate] (No Quer y Form) This command causes the ins t rument to beep immediately . Gr oup System Syntax SYSTem:BEE Per[:IMMedia te] Arguments None Examples SYSTem:BEE Per:IMMediat e causes a beep.
Syntax and Command s AFG3000 Series Arbitrary/Functio n Generators Reference Manual 3-95 SYST em:ERRor[:NEXT]? This query-only co mmand returns the contents of the Error/Ev ent queue.
Syntax and Co mmands 3-96 AFG3000 Series Arbitrary/Function Generators Reference Manual SYST em:KLOCk[:ST A T e] This command locks or unlocks the inst rument front panel controls.
Syntax and Command s AFG3000 Series Arbitrary/Functio n Generators Reference Manual 3-97 SYST em:ULANgua ge This command sets or queries the language that the instrument uses to display information on the screen.
Syntax and Co mmands 3-98 AFG3000 Series Arbitrary/Function Generators Reference Manual T R AC e | DA T A : C A T a l o g ? This query-only comman d re turns the names of user wa v eform memory and edit memory . Gr oup Tr a c e Syntax TRACe|DATA :CATalog? Arguments None Returns <string> A series of strings separated by commas is returned.
Syntax and Command s AFG3000 Series Arbitrary/Functio n Generators Reference Manual 3-99 T R AC e | DA T A [ : DA T A ] This command transfers the wa veform data from the e xternal controller to the edit memory in the arbitrary/function generator. The query command returns the binary block data.
Syntax and Co mmands 3-100 AFG3000 Series Arbitrary/Function Generators Reference Manual TRA Ce|D A T A[:D A T A]:LINE (No Query Form) This command writes line data to the edit memory . The data between the specified points is interp olated linearly .
Syntax and Command s AFG3000 Series Arbitrary/Functio n Generators Reference Manual 3-101 T R AC e | DA T A [ : DA T A ] : V A L u e This command sets or queries the data v alue at the specif ie d point in th e edit memory .
Syntax and Co mmands 3-102 AFG3000 Series Arbitrary/Function Generators Reference Manual TRA Ce|D A T A:DEFine (No Query Form) This command resets the contents of edit memory .
Syntax and Command s AFG3000 Series Arbitrary/Functio n Generators Reference Manual 3-103 TRA Ce|D A T A:DELete[:NAME] (No Query Form) This command deletes the contents of specif ied user wa veform memory .
Syntax and Co mmands 3-104 AFG3000 Series Arbitrary/Function Generators Reference Manual T R AC e | DA T A : P O I N t s This command sets or queries the number of data points for the wa veform created in the edit memory .
Syntax and Command s AFG3000 Series Arbitrary/Functio n Generators Reference Manual 3-105 TRIGger[:SEQuence]:SLOP e This command sets or queries the slope of trigger signal.
Syntax and Co mmands 3-106 AFG3000 Series Arbitrary/Function Generators Reference Manual TRIGger[:SEQuence]:TIMer This command sets or queries th e period of an internal clock when you select the internal clock as the trigger source with the T RIGger[:SEQu ence]:SOURce command.
Syntax and Command s AFG3000 Series Arbitrary/Functio n Generators Reference Manual 3-107 *TST? This command performs a self-t est and returns the results. Gr oup Calibration and Diagnostic Related Commands DIAGnostic [:ALL]? Syntax *TST? Arguments None Returns <NR1> where <NR1>=0 indicates that the sel f-test completed without errors.
Syntax and Co mmands 3-108 AFG3000 Series Arbitrary/Function Generators Reference Manual.
Status and Events.
.
AFG3000 Series Arbitrary/Functio n Generators Reference Manual 4-1 Status and Events This section provides deta ils about the status inform ation and ev ents the arbi- trary/function generator reports. Status Repor ting Structure The arbitrary/function g enerator status reporting functions conform to IEEE-488.
Status and Events 4-2 AFG3000 Series Arbitrary/Function Generators Reference Manual Figure 4-1: Err or and event handlin g process 0 0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7 8 9 10 10 11 11 12 12 13 13 14 14 1.
Status and Events AFG3000 Series Arbitrary/Functio n Generators Reference Manual 4-3 Standard/Event Status Block This block is used to report po wer on/o ff, command error , an d command ex ecution status. The block has tw o registers: the Standard Event Status Re gister (SESR) and the Event Status Enable Re gister (ESER).
Status and Events 4-4 AFG3000 Series Arbitrary/Function Generators Reference Manual Register s The registers in the e v ent reporting sy stem fall into tw o functional groups: The Status Registers contain informatio n about the status of the instrument.
Status and Events AFG3000 Series Arbitrary/Functio n Generators Reference Manual 4-5 Status Byte Register (SBR). The SBR is made up of 8 b its. Bits 4, 5 and 6 are defined in accordance with IEEE Std 488.2 -1992 (see Figure 4-2). T hese bits are used to monitor the outp ut queue, SESR, and service requests, respecti vely .
Status and Events 4-6 AFG3000 Series Arbitrary/Function Generators Reference Manual Standar d Event Status Register (SESR). The SESR records eight types of e vents that can occur within the instrument as sho wn in Figure 4-3. Figure 4-3: The Standar d Even t Status Register (SESR) T able 4-2: SESR bit functions Bit Function 7 (MSB) PON P o wer On.
Status and Events AFG3000 Series Arbitrary/Functio n Generators Reference Manual 4-7 Operation Event Register (OEVR). This re gister has the same content as the Opera- tion Condition Register .
Status and Events 4-8 AFG3000 Series Arbitrary/Function Generators Reference Manual Questionable Event Register (QEVR). This re gister has the same content as the Questionable Condition Re gister .
Status and Events AFG3000 Series Arbitrary/Functio n Generators Reference Manual 4-9 Use the *ESC command to set the bits in the ESER. U se the *ESR? query to read the contents of the ESER. Figure 4-6 sho ws the ESER functions. Figure 4-6: Event Statu s Enable Registe r (ESER) Service Request Enable Register (SRER).
Status and Events 4-10 AFG3000 Series Arbitrary/Function Generators Reference Manual Questionable Enable Register (QENR). The QENR consists of bits def ined exactly the same as bits 0 t hrough 15 in the QEVR re gister (see Figure 4-9).
Status and Events AFG3000 Series Arbitrary/Functio n Generators Reference Manual 4-11 Messages and Codes Error and e vent codes with ne gati ve v alues are SCPI standard codes. Error and e vent codes with positi v e values are uniq ue to the AFG3000 Series Arbitrary/Func- tion Generators.
Status and Events 4-12 AFG3000 Series Arbitrary/Function Generators Reference Manual –113 Undefined header –114 Header suffix out of range –115 Unexpected n umber of parameters –120 Numeric da.
Status and Events AFG3000 Series Arbitrary/Functio n Generators Reference Manual 4-13 Execution Err ors T able 4-7 lists the errors that are detected during execution of a command.
Status and Events 4-14 AFG3000 Series Arbitrary/Function Generators Reference Manual –274 Macro parameter error –275 Macro definition too long –276 Macro recursion error –277 Macro redefinitio.
Status and Events AFG3000 Series Arbitrary/Functio n Generators Reference Manual 4-15 Device Specific Err ors T able 4-8 lists the device-specif ic errors that can occur during arbitrary/function generator oper ation. These e rrors may indicate that th e instrument needs repa ir .
Status and Events 4-16 AFG3000 Series Arbitrary/Function Generators Reference Manual User Request Events These e vents are not used in thi s instrument.
Status and Events AFG3000 Series Arbitrary/Functio n Generators Reference Manual 4-17 Device Err ors T able 4-14 lists the error codes that ar e unique to the AFG3 000 Series Arbi- trary/Function Generators.
Status and Events 4-18 AFG3000 Series Arbitrary/Function Generators Reference Manual 2305 Self-test failed; CH1 Outp ut gain 2306 Self-test failed; CH2 Outp ut gain 2401 Self-test failed; CH1 x 3 d B .
Pr ogramming Examples.
.
AFG3000 Series Arbitrary/Functio n Generators Reference Manual 5-1 Pr ogramming Examples The follo wing two example prog rams, wh ich demonstrate methods that you can use to control the arbitrary/func.
Programming Examples 5-2 AFG3000 Series Arbitrary/Function Generators Reference Manual Example 1 This is a sample program for setting th e arbitrary/function generator outputs. Private Sub Samp le1_Click() ' 'Assign resource ' Tvc1.Descriptor = "GPIB 0::11::INSTR" ' 'Initialize of d evice setting ' Tvc1.
Programming Examples AFG3000 Series Arbitrary/Functio n Generators Reference Manual 5-3 Example 2 This is a sample program for sending an arbitrary wav eform to the arbitrary/func- tion generator's Edit Memory and cop ying th e contents of Edit Memory to the user wa veform memory .
Programming Examples 5-4 AFG3000 Series Arbitrary/Function Generators Reference Manual Next i For i = 1000 To 1999 'Part of Low Level (1000 Points) Data = 0 High = Int(Data / 256) Low = Data - (H.
Appendices.
.
AFG3000 Series Arbitrary/Functio n Generators Reference Manual A-1 Appendix A: Accessories and Options This section lists the standard and optiona l accessories a vailable for the instrument, as well as the product options.
Appendix A: Accessories and Options A-2 AFG3000 Series Arbitrary/Function Generators Reference Manual Accessories All accessories (standard and optional) are a v ailable by contacting your local T ektronix field of f ice. T able A-2 lists standard accessories for this instrument.
Appendix A: Accessories and Options AFG3000 Series Arbitrary/Functio n Generators Reference Manual A-3 Fuse Adap ter . The arbitrary/function generator w ill be damaged if a large DC or A C v oltage is applied to the output or input connectors. T o protect the output circuits, a fuse adapter is pro vided as an optional accessory .
Appendix A: Accessories and Options A-4 AFG3000 Series Arbitrary/Function Generators Reference Manual.
AFG3000 Series Arbitrary/Functio n Generators Reference Manual B-1 Appendix B: General Care and Cleaning General Care Do not store or lea ve the arbitrary/function generator where the LCD display will be exposed to d irect sunlight for long periods of time.
Appendix B: General Care and Cleanin g B-2 AFG3000 Series Arbitrary/Function Generators Reference Manual.
AFG3000 Series Arbitrary/Functio n Generators Reference Manual C-1 Appendix C: SCPI Conf ormance Inf ormation All commands in the arbitrary/function generator are based on SCPI V ersion 1999.0. T able C-1 lists the SCPI commands the arb itrary/function generator supports.
Appendix C: SCPI Con formance Information C-2 AFG3000 Series Arbitrary/Function Generators Reference Manual SOURce(?) √ [DEPTh](?) √ BURSt MODE (?) √ NCYCles(?) √ TDELay(?) √ [ST A T e](?) .
Appendix C: SCPI Conformance Information AFG3000 Series Arbitrary/Functio n Generators Reference Manual C-3 PERiod(?) √ TRANsition TRAiling(?) √ [LEADing](?) √ WIDTh(?) √ PWM INT er nal FREQue.
Appendix C: SCPI Con formance Information C-4 AFG3000 Series Arbitrary/Function Generators Reference Manual TRA Ce|D A T A CA T alog? √ COPY √ [D A T A](?) √ LINE √ V ALue(?) √ DEFine √ DE.
AFG3000 Series Arbitrary/Functio n Generators Reference Manual D-1 Appendix D: Default Setup T able D-1 lists the settings that are re stored when you pu sh the front-panel Default button. T able D-1: Default settings Menu or System Default setting Output configuration Function Sine F requency 1.
Appendix D: Default Setup D-2 AFG3000 Series Arbitrary/Function Generators Reference Manual The front-panel Default button does not reset the follo wing settings: Language option Po wer-on set.
Inde x.
.
AFG3000 Series Arbitrary/Functio n Generators Reference Manual Inde x-1 Symbols +/- button 1-6 A ABORt 3-15 Accessories A-1 Action buttons 1-3 Add external signal, Output men u 2-12 ADD INPUT connecto.
Index Index-2 AFG3000 Series Arbitrary/Function Generators Reference Manual Sav e menu 2-13 Error/Event Queue 4-10 *ESE 3-21 ESER 4-8 *ESR? 3-22 Event Status Enable Re gister 4-3 , 4- 8 Execution erro.
Index AFG3000 Series Arbitrary/Functio n Generators Reference Manual Inde x-3 N New , Edit menu 2-17 Noise More wa veform menu 2-6 Output menu 2-12 Number of Poi nts, Edit menu 2-16 Numeric input 1-15.
Index Index-4 AFG3000 Series Arbitrary/Function Generators Reference Manual Security slot, rear panel 1-20 Select a channel 1-7 Service Manual, part number A-2 Service options A-1 Service Request Enab.
Index AFG3000 Series Arbitrary/Functio n Generators Reference Manual Inde x-5 Standard Event Status Register 4-3 , 4-6 State buttons 1-7 Status Byte Register 4-5 Status reporting structure 4-1 Status,.
Index Index-6 AFG3000 Series Arbitrary/Function Generators Reference Manual.
Ein wichtiger Punkt beim Kauf des Geräts Tektronix AFG3000 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Tektronix AFG3000 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Tektronix AFG3000 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Tektronix AFG3000 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Tektronix AFG3000 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Tektronix AFG3000 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Tektronix AFG3000 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Tektronix AFG3000. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Tektronix AFG3000 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
