Benutzeranleitung / Produktwartung ST536 des Produzenten Technicolor - Thomson
Zur Seite of 792
Power DSL Ethernet Internet Thomson ST516/536/546 CLI Reference Guide.
.
Thomson ST516/536/546 CLI Reference Guide R6.2.
Copyright Copyright ©1999-2007 THOMSON. All rights reserved. Distribution and co pying of this do cument, use and communication o f its contents is not permitted witho ut written authorizatio n from THOMSON.
E-DOC-CTC-20061 027-0003 v2.0 Contents i About this CLI Reference Guide ....................... ......................... 1 1 Root Commands ........................ .................................................. 3 ping .......... ................ .
E-DOC-CTC-2006 1027-0003 v2.0 Contents ii atm debug aal5s tats ........... ................ .............. .............. ................. .............. .............. ........ ............... .. 41 atm debug gstats .... ................. ..........
E-DOC-CTC-20061 027-0003 v2.0 Contents iii 6 Connection Commands....... .............................. ........................ 81 connection app config ................. .............. ................. .............. .............. .................
E-DOC-CTC-2006 1027-0003 v2.0 Contents iv dhcp client debu g traceconfig ............................ ................. ................. ................. ................. .. ...... ... 121 dhcp client rqoptio ns add .......... ................. ...
E-DOC-CTC-20061 027-0003 v2.0 Contents v dhcp server option instdelete ..................... ................. ................ ................. .................... ....... .......... 163 dhcp server option instlist ....................... .........
E-DOC-CTC-2006 1027-0003 v2.0 Contents vi dns server route delete .................... ................ .................... ................. ................. .............. .............. 205 dns server route flush ............. .............. ....
E-DOC-CTC-20061 027-0003 v2.0 Contents vii env set ............. ................. .............. .............. ................. .............. .............. ................ . ......................... 247 env unset ............ .............. ...
E-DOC-CTC-2006 1027-0003 v2.0 Contents viii eth bridge maclist ......... ................. .............. .............. .............. ................. .............. .......... ......... ......... 289 eth bridge mcdadd ............. .............. .
E-DOC-CTC-20061 027-0003 v2.0 Contents ix 15 Expr Commands .................. .............................. ...................... 327 expr add .... .............. .............. ................. .............. .............. ................. .....
E-DOC-CTC-2006 1027-0003 v2.0 Contents x grp rip flush................... .............. ................. .............. .............. .............. ................. ..... ....................... 382 grp rip ifcon fig ...................... ......
E-DOC-CTC-20061 027-0003 v2.0 Contents xi igmp proxy ifl ist .................. ................ .............. .............. ................. .............. .............. ... .................... 422 igmp proxy mb slist ......... .................
E-DOC-CTC-2006 1027-0003 v2.0 Contents xii ip auto ifdetach ............. .............. .............. ................. .............. .............. ................. ........ .............. ...... 465 ip auto ifli st ........... .............. ...
E-DOC-CTC-20061 027-0003 v2.0 Contents xiii language co nfig ......... ................. .............. .............. .............. ................. .............. ............. ....... ........... 514 language delete .................... .........
E-DOC-CTC-2006 1027-0003 v2.0 Contents xiv mlp privilege co nfig ........... .............. .............. ................ .............. .............. ................. ....... ................ 552 mlp privilege d elete ................. ..........
E-DOC-CTC-20061 027-0003 v2.0 Contents xv ppp relay ifdel ete .................. .............. .............. ................. .............. .............. ................. . ................... 607 ppp relay ifli st ..................... ........
E-DOC-CTC-2006 1027-0003 v2.0 Contents xvi service system modify .......................... ................. ................. ................. ................... .......... ............. 647 34 SNMP Commands ............... .......................
E-DOC-CTC-20061 027-0003 v2.0 Contents xvii system ra config .............. .............. .............. ................. .............. .............. ................ ........ ............... ... 687 system rtc synchronize ................. ......
E-DOC-CTC-2006 1027-0003 v2.0 Contents xviii user flush ......... .............. ................. .............. .............. ................. .............. .............. .... .................. ...... 727 user list ............... .............
E-DOC-CTC-20061 027-0003 v2.0 About this CLI Reference Guide 1 About this CLI Reference Guide Used Symbols T erminology Generally , the Thomson ST 516/536/546 will be referred to as Thom son ST in this CLI Reference Guide.
E-DOC-CTC-2006 1027-0003 v2.0 About this CLI Reference Guide 2.
E-DOC-CTC-20061 027-0003 v2.0 Root Commands 3 1 Root Commands From the root pr ompt, you can choose one of the foll owing commands: EXAMPLE: Comma nd Description help Displays the help information. ? menu Displays the menu. exit Exits the shell. .. Exits group selection .
E-DOC-CTC- 20061027-0003 v2 .0 Root Commands 4 ping Send ICMP ECHO_REQUES T packets. SYNT AX: where: EXAMPLE: ping proto = <{ip|atm}> addr = <ip-address> dest = <string> [count = <.
E-DOC-CTC-20061 027-0003 v2.0 Root Commands 5 traceroute Send ICMP/UDP packets to trace the IP path. SYNT AX: where: traceroute addr = <ip-address> [count = <number{1-10}>] [size = <num.
E-DOC-CTC- 20061027-0003 v2 .0 Root Commands 6 EXAMPLE: =>traceroute addr = 192.193.195.250 count=3 size=1 interval=1000 maxhops=30 dstport=33433 maxfail=5 type=icmp utime=yes :traceroute addr=192.
E-DOC-CTC-20061 027-0003 v2.0 ADSL Commands 7 2 ADSL Commands Introduction This chapter describes the commands of the adsl command group. Contents This chapter covers th e following commands: adsl config Show/set the Asymmetric Digital Sub scriber Line (ADSL) configuration .
E-DOC-CTC- 20061027-0003 v2 .0 ADSL Commands 8 adsl config Show/set the Asymmetric Digital Su bscriber Line (ADSL) configuration. SYNT AX: where: EXAMPLE: The example belo w shows the default configur.
E-DOC-CTC-20061 027-0003 v2.0 ADSL Commands 9 adsl info Display the ADSL statistics and inform ation about the DSL line st atus. Although the same comma nd is used for both Thomson ST ADSL/POTS and Thomson ST ADSL/ISDN variants, the command features specific ou tput parameters and counters per variant.
E-DOC-CTC- 20061027-0003 v2 .0 ADSL Commands 10 EXAMPLE (for a Thomson ST ADSL/POTS variant): =>adsl info Modemstate : up Operation Mode : G.992.1 Annex A Channel Mode : interleaved Number of resets : 1 Vendor Local Remote Country : 0f 00 Vendor : TMMB VendorSpecific : 0000 0000 StandardRevisionNr : 00 00 Downstream Upstream Margin [dB] : 26.
E-DOC-CTC-20061 027-0003 v2.0 ADSL Commands 11 adsl debug bitloadinginfo Displays the number of bi ts per tone. Syntax adsl debug bitloadinginfo.
E-DOC-CTC- 20061027-0003 v2 .0 ADSL Commands 12 adsl debug deltconfig Enable/disable the Du al Ended Line T es ting Interface (DEL T) Syntax where: adsl debug deltconfig [state = <{disabled|enabled.
E-DOC-CTC-20061 027-0003 v2.0 ADSL Commands 13 adsl debug deltinfo Display Dual En ded Line T est ing Interface (DEL T) results Syntax adsl debug deltinfo.
E-DOC-CTC- 20061027-0003 v2 .0 ADSL Commands 14 adsl debug modemoptioninfo Displays the modem op tions bitmap Syntax adsl debug modemoptioninfo.
E-DOC-CTC-20061 027-0003 v2.0 ADSL Commands 15 adsl debug modemoption Configure the modem options bitmap Syntax where: adsl debug modemoption [config = <hexbitmap>] config The modem options bitm.
E-DOC-CTC- 20061027-0003 v2 .0 ADSL Commands 16 adsl debug traceconfig Configure the ADSL tracelevel. Syntax where: adsl debug traceconfig [level = <number{0-2}>] level T race Level : > 0=dis.
E-DOC-CTC-20061 027-0003 v2.0 ATM Commands 17 3 A TM Commands Introduction This chapter describes the commands of the atm comman d group. Contents This chapter covers th e following commands: atm flush Flush all Asynchrono us T ransfer Mode (A TM) interfaces.
E-DOC-CTC- 20061027-0003 v2 .0 ATM Commands 18 atm oam vclb add Create a loopback connection for VC. 52 atm oam vclb del Delete a loopback connection for VC. 53 atm oam vclb list List all VC loopb ack connections. 54 atm phonebook add Add a new phoneboo k entry .
E-DOC-CTC-20061 027-0003 v2.0 ATM Commands 19 atm flush Flush all Asynchro nous T ransfer Mode ( A TM) interfaces. SYNT AX: atm flush.
E-DOC-CTC- 20061027-0003 v2 .0 ATM Commands 20 atm ifadd Create a new A TM interface. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: atm ifadd intf = <string> intf The name for th e new A TM interface. Note If not specified, the destination para meter must be specified.
E-DOC-CTC-20061 027-0003 v2.0 ATM Commands 21 atm ifattach Attach a A TM interface. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: atm ifattach intf = <string> intf The name of the A TM interf ace to be attached.
E-DOC-CTC- 20061027-0003 v2 .0 ATM Commands 22 atm ifconfig Configure an A TM interface. SYNT AX: where: i The interface to be configured must not be connected at the tim e of configuration. If this should be the case, use the command :atm ifdetach before using the command :atm ifconfig .
E-DOC-CTC-20061 027-0003 v2.0 ATM Commands 23 EXAMPLE: ulp Select the Upper Layer Protoc ol (ULP) for this interface. Choose between: > ip (for a Routed IPoA interface). > mac (for a Bridged Ethernet, Rout ed ETHoA, Bridged PPP ov er Ethernet (PPPoE), Ro uted PPPoE or a PPPoE Relay i nterface).
E-DOC-CTC- 20061027-0003 v2 .0 ATM Commands 24 atm ifdelete Delete an A TM interface . SYNT AX: where: EXAMPLE: RELA TED COMMANDS: atm ifdelete intf = <string> intf The name of the A TM interface to be deleted.
E-DOC-CTC-20061 027-0003 v2.0 ATM Commands 25 atm ifdetach Detach an A TM interface. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: atm ifdetach intf = <string> intf The name of the A TM interf ace to be detached.
E-DOC-CTC- 20061027-0003 v2 .0 ATM Commands 26 atm iflist Display the A TM interfaces. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: atm iflist [intf = <string>] intf The name of the A TM interface to be shown. Note If not specified, al l the A TM interfaces are show n.
E-DOC-CTC-20061 027-0003 v2.0 ATM Commands 27 atm bundle add Add a new bundle of interfaces. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: atm bundle add name = <string> name The name of the new bundle.
E-DOC-CTC- 20061027-0003 v2 .0 ATM Commands 28 atm bundle attach Attach a bundle of interfaces. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: atm bundle attach name = <string> name The name of the b undle to be attached.
E-DOC-CTC-20061 027-0003 v2.0 ATM Commands 29 atm bundle config Modify a bundle of interf aces. SYNT AX: where: EXAMPLE: i The bundle of interfaces to be configu red must not be connected at the time of configuration. If this should be the case , use the command :atm bundle de tach before using the command :atm bundle c onfig .
E-DOC-CTC- 20061027-0003 v2 .0 ATM Commands 30 atm bundle clear Clear the bundle statistics. SYNT AX: where: atm bundle clear [name = <string>] name The name of the b undle for wh ich the statistics must be cleared. Note If not specified, t he statistics for all the bund les will be cleared.
E-DOC-CTC-20061 027-0003 v2.0 ATM Commands 31 atm bundle delete Delete a bundle of interfaces. SYNT AX: where: RELA TED COMMANDS: atm bundle delete name = <string> name The name of the bundle to be deleted. REQUIRED atm bundle add Add a new bundle of interfaces.
E-DOC-CTC- 20061027-0003 v2 .0 ATM Commands 32 atm bundle detach Detach a bundle of interfac es. SYNT AX: where: RELA TED COMMANDS: atm bundle detach intf = <string> intf The na me of the bundle to be detached . REQUIRED atm bundle attach Attach a bu ndle of interfaces.
E-DOC-CTC-20061 027-0003 v2.0 ATM Commands 33 atm bundle flush Flush all bund les. SYNT AX: atm bundle flush.
E-DOC-CTC- 20061027-0003 v2 .0 ATM Commands 34 atm bundle ifadd Add an interface on a bundle. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: i Up to 8 interfaces or (sub-)bund les can be added to one bund le.
E-DOC-CTC-20061 027-0003 v2.0 ATM Commands 35 atm bundle ifconfig Configure an interface from a bundle. SYNT AX: where: i The interface to be configured must not be connected at the tim e of configuration. If this should be the case, use the command :atm bundle ifde tach before using th e command :atm bundle ifconfig .
E-DOC-CTC- 20061027-0003 v2 .0 ATM Commands 36 atm bundle ifdelete Remove an interface from a bundle. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: atm bundle ifdelete name = <string> intf = <string> name The name of the b undle from which an A TM interface must be removed.
E-DOC-CTC-20061 027-0003 v2.0 ATM Commands 37 atm bundle list Display the current bundles. SYNT AX: EXAMPLE: RELA TED COMMANDS: atm bundle list =>atm bundle list Test : Connection state : not-conne.
E-DOC-CTC- 20061027-0003 v2 .0 ATM Commands 38 atm cac config Configure the A TM connec tion admission co ntrol. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: atm cac config config port = <{dsl0|dsl1|atm2|atm3|aal5|atm5} or number> state = <{disabled|enabled}> config port The port for which CAC is co nfigured.
E-DOC-CTC-20061 027-0003 v2.0 ATM Commands 39 atm cac list Display all the CAC parameters. SYNT AX: EXAMPLE: RELA TED COMMANDS: atm cac list {Administrator}[atm cac]=>list CAC: port: dsl0 state: en.
E-DOC-CTC- 20061027-0003 v2 .0 ATM Commands 40 atm cac overbooking Configure A TM overboo king parameters. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: atm cac overbooking rt = <number{0-1000}> nrt = <number{0-1000}> rt A number between 0 and 1000.
E-DOC-CTC-20061 027-0003 v2.0 ATM Commands 41 atm debug aal5stats Display A TM Adaptation Layer 5 (AAL 5) port specific A TM statistics. SYNT AX: where: RELA TED COMMANDS: atm debug aal5stats port = &.
E-DOC-CTC- 20061027-0003 v2 .0 ATM Commands 42 atm debug gstats Display A TM global statistics. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: atm debug gstats [clear = <{disabled | enabled}>] clear Enabl e or disable clearing of the statistics after request.
E-DOC-CTC-20061 027-0003 v2.0 ATM Commands 43 atm debug portstats Display port specific A TM statistics. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: atm debug portstats port = <{dsl0} or number> [clear = <{disabled | enabled}>] port The port number for whic h statistics will be retrieved.
E-DOC-CTC- 20061027-0003 v2 .0 ATM Commands 44 atm oam config Modify the A TM Operation and Maintenance (OAM) settings. SYNT AX: where: RELA TED COMMANDS: atm oam config [clp = <number{0-1}>] [loopbackid = <string>] clp A number (0 or 1). Represents th e Cell Loss Priority (CLP) bit value of the OAM cells.
E-DOC-CTC-20061 027-0003 v2.0 ATM Commands 45 atm oam list Display the A TM OAM settings. SYNT AX: EXAMPLE: RELA TED COMMANDS: atm oam list =>atm oam list OAM config dump ------------------- CLP bi.
E-DOC-CTC- 20061027-0003 v2 .0 ATM Commands 46 atm oam modify Modify the A TM OAM data b locking mode. SYNT AX: where: atm oam modify port = <{dsl0} or number> blocking = <{disabled | enabled}> port The port for which OA M blocking is configur ed.
E-DOC-CTC-20061 027-0003 v2.0 ATM Commands 47 EXAMPLE: RELA TED COMMANDS: =>atm oam list OAM config dump ------------------- CLP bit value : 1 Loopback id : 6a 6a 6a 6a 6a 6a 6a 6a 6a 6a 6a 6a 6a 6.
E-DOC-CTC- 20061027-0003 v2 .0 ATM Commands 48 atm oam ping Send A T M loopback cells. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: atm oam ping dest = <string> [count = <number{1-1000000}>] [interval = <number{100-1000000}>] dest The destination address for the request.
E-DOC-CTC-20061 027-0003 v2.0 ATM Commands 49 atm oam cc list Display Continuity Che ck (CC) configuration. SYNT AX: EXAMPLE: RELA TED COMMANDS: atm oam cc list =>atm oam cclist PORT = 0 VPI = 15 V.
E-DOC-CTC- 20061027-0003 v2 .0 ATM Commands 50 atm oam cc modify Modify CC on the connection . SYNT AX: where: RELA TED COMMANDS: atm oam modify port = <{dsl0|dsl1|atm2|atm3|aal5|atm5} or number>.
E-DOC-CTC-20061 027-0003 v2.0 ATM Commands 51 atm oam cc send Send CC activate/deact ivate to connection. SYNT AX: where: RELA TED COMMANDS: atm oam cc send port = <{dsl0} or number> vpi = <n.
E-DOC-CTC- 20061027-0003 v2 .0 ATM Commands 52 atm oam vclb add Create a loopback connection for VC. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: atm oam vclb add port = <{dsl0} or number> vpi = <number{0-15}> [vci = <number{0-511}>] port The A TM port number .
E-DOC-CTC-20061 027-0003 v2.0 ATM Commands 53 atm oam vclb del Delete a loop back connection for VC. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: atm oam vclb del port = <{dsl0} or number> vpi = <number{0-15}> [vci = <number{0-511}>] port The A TM port number .
E-DOC-CTC- 20061027-0003 v2 .0 ATM Commands 54 atm oam vclb list List all VC loopback connections. SYNT AX: EXAMPLE: RELA TED COMMANDS: atm oam vclb list =>atm oam vclb list PORT = 0 VPI = 0 VCI = 36 PORT = 1 VPI = 0 VCI = 37 => atm oam vclb add Create a loopback co nnection for VC.
E-DOC-CTC-20061 027-0003 v2.0 ATM Commands 55 atm phonebook add Add a new phonebook entry . SYNT AX: where: EXAMPLE: RELA TED COMMANDS: atm phonebook add name = <string> addr = <atmchannel : PVC syntax is [port.]vpi.vci port=dsl0 | ...> name The name of the new ph onebook entry .
E-DOC-CTC- 20061027-0003 v2 .0 ATM Commands 56 atm phonebook autolist Show the auto PVCs. SYNT AX: EXAMPLE: RELA TED COMMANDS: i Auto PVCs are only shown if they are su pported by the Central Office DSLAM. atm phonebook autolist =>atm phonebook autolist 8.
E-DOC-CTC-20061 027-0003 v2.0 ATM Commands 57 atm phonebook delete Delete an existing ph onebook entry . SYNT AX: where: EXAMPLE: RELA TED COMMANDS: i This command is only ap plicable for phonebook entries that are not used (in other wo rds, not configured for any packet service).
E-DOC-CTC- 20061027-0003 v2 .0 ATM Commands 58 atm phonebook flush Flush all the phoneb ook entries. SYNT AX: EXAMPLE: i 1. Phonebook entries that ar ei nu s e ,c a n n o tb ef l u s h e d . 2. This command does not impa ct pre viously saved configurations.
E-DOC-CTC-20061 027-0003 v2.0 ATM Commands 59 atm phonebook list Display the current phonebook. SYNT AX: EXAMPLE: RELA TED COMMANDS: atm phonebook list =>atm phonebook list Name Use Address atm_pvc_0_35 1 0.35 RtPPPoA 0 8.35 => atm phonebook add Add a new phoneboo k entry .
E-DOC-CTC- 20061027-0003 v2 .0 ATM Commands 60 atm qosbook add Add a new QoS book entry . SYNT AX: where: EXAMPLE: RELA TED COMMANDS: atm qosbook add name = <string> [txctd = <string>] [rxctd = <string>] name The name of the new QoS entry .
E-DOC-CTC-20061 027-0003 v2.0 ATM Commands 61 atm qosbook config Modify the QoS book configuration . SYNT AX: where: EXAMPLE: atm qosbook config [format = <{bytes | cells}>] format The in put/output format of the QoS book. Choose between: > byte s : the output is shown in Kbits or bytes.
E-DOC-CTC- 20061027-0003 v2 .0 ATM Commands 62 atm qosbook ctdadd Add a Connection T ra ffic Descriptor (CTD). SYNT AX: where: EXAMPLE: atm qosbook ctdadd name = <string> conformance = <{UBR .
E-DOC-CTC-20061 027-0003 v2.0 ATM Commands 63 IMPORT ANT NOTE: The Thomson ST always rounds up specified burst sizes to a multiple of 48 by tes (a multiple of A TM cells). Example: In the example below a burst size of 100 bytes is specified (maxburst=100).
E-DOC-CTC- 20061027-0003 v2 .0 ATM Commands 64 atm qosbook ctddelete Delete a C TD. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: atm qosbook ctddelete name = <string> [force = <{disabled | enabled}>] name The name of the C TD entry to be deleted.
E-DOC-CTC-20061 027-0003 v2.0 ATM Commands 65 atm qosbook ctdlist Display all CTDs. SYNT AX: EXAMPLE: RELA TED COMMANDS: atm qosbook ctdlist =>atm qosbook ctdlist Name Ref Conf Peak Sust Burst Minr.
E-DOC-CTC- 20061027-0003 v2 .0 ATM Commands 66 atm qosbook delete Delete a QoS b ook entry . SYNT AX: where: EXAMPLE: RELA TED COMMANDS: atm qosbook delete name = <string> [force = <{disabled | enabled}>] name The name of the QoS book entry to be d eleted.
E-DOC-CTC-20061 027-0003 v2.0 ATM Commands 67 atm qosbook flush Flush all the QoS book entries. SYNT AX: i The flush command do es not impact previously save d configuration s.
E-DOC-CTC- 20061027-0003 v2 .0 ATM Commands 68 atm qosbook list Display the QoS book. SYNT AX: EXAMPLE: RELA TED COMMANDS: atm qosbook list =>atm qosbook list Name Ref Type TX peak sust burst RX pe.
E-DOC-CTC-20061 027-0003 v2.0 AutoPVC Commands 69 4 AutoPVC Commands Introduction This chapter describes the commands of the autopv c command group. Contents This chapter covers th e following commands: autopvc config Configure autopvc. 70 autopvc list Show the retrie ved information.
E-DOC-CTC- 20061027-0003 v2 .0 AutoPVC Commands 70 autopvc config Configure autopvc. SYNT AX: where: autopvc config [mode = <{pseudo | passive | active}>] [type = <{bridge | pppoerelay | ipoa.
E-DOC-CTC-20061 027-0003 v2.0 AutoPVC Commands 71 EXAMPLE: =>autopvc config Autopvc mode : passive Autopvc type : Autopvc standard: unknown Autopvc pseudo : unknown UBR overwrite : disabled UBR pea.
E-DOC-CTC- 20061027-0003 v2 .0 AutoPVC Commands 72 autopvc list Show the retrieved information. SYNT AX: where: EXAMPLE: autopvc list [table = <{Port | AtmLayer | Vpc | Vcc | Address | AddressRegis.
E-DOC-CTC-20061 027-0003 v2.0 Config Commands 73 5 Config Commands Introduction This chapter describes the commands of the config command group. Contents This chapter covers th e following commands: config delete Delete a user con figuration file. 74 config dump Show the saved configuration file.
E-DOC-CTC- 20061027-0003 v2 .0 Config Commands 74 config delete Delete a user configuration file. SYNT AX: where: RELA TED COMMANDS: config delete [filename = <string>] filename Name of the user con figuration file to b e deleted.
E-DOC-CTC-20061 027-0003 v2.0 Config Commands 75 config dump Show the saved configuratio n file. SYNT AX: where: RELA TED COMMANDS: config dump [sections = <string>] sections Sections to be dumped OP TIONAL config delete Delete a user configuration fi le.
E-DOC-CTC- 20061027-0003 v2 .0 Config Commands 76 config flush Flush the loaded configu ration. SYNT AX: where: i 1. This flush command combines all the possible fl ush commands. 2. This command does not affect saved configurations. config flush [flush_ip = <{enabled | disabled}>] flush_ip Flush IP settings (enabled) or not (dis abled).
E-DOC-CTC-20061 027-0003 v2.0 Config Commands 77 config list Show the current configuration set. SYNT AX: where: RELA TED COMMANDS: config list [templates = <{disabled | enabl ed}>] templates List the template file s (disabled) or not (enabled).
E-DOC-CTC- 20061027-0003 v2 .0 Config Commands 78 config load Load complete saved (backup) or default configuration file. SYNT AX: where: i Use the command :config fl ush before loading a conf iguration file .
E-DOC-CTC-20061 027-0003 v2.0 Config Commands 79 EXAMPLE: RELA TED COMMANDS: =>ip rtlist Destination Source Gateway Intf Mtrc 10.0.0.0/24 10.0.0.0/24 10.0.0.140 eth0 0 172.16.0.5/32 0.0.0.0/0 172.16.0.5 cip1 0 10.0.0.140/32 0.0.0.0/0 10.0.0.140 eth0 0 127.
E-DOC-CTC- 20061027-0003 v2 .0 Config Commands 80 config save Store the current config uration in a backup file. All the existing configurations an d modifi cations entered by the user are saved. The backup file is saved in the Thomson ST permanent storage.
E-DOC-CTC-20061 027-0003 v2.0 Connection Commands 81 6 Connection Commands Introduction This chapter describes the commands of the connec tion command group. Contents This chapter covers th e following commands: connection appconfig Configure the avail able CONN/NA T application helpers.
E-DOC-CTC- 20061027-0003 v2 .0 Connection Commands 82 connection appconfig Configure the available CONN/ NA T application hel pers. SYNT AX: where: connection appconfig application = <string> [t.
E-DOC-CTC-20061 027-0003 v2.0 Connection Commands 83 EXAMPLE: RELA TED COMMANDS: =>connection applist Application Proto DefaultPort Traces Timeout IP6TO4 6to4 0 enabled unavailable PPTP tcp 1723 en.
E-DOC-CTC- 20061027-0003 v2 .0 Connection Commands 84 connection appinfo Display CONN/NA T application specific info. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: connection appinfo application = <{string} > application The name of a CONN /NA T application helper .
E-DOC-CTC-20061 027-0003 v2.0 Connection Commands 85 connection applist List the available CONN/N A T application helpers. SYNT AX: EXAMPLE: RELA TED COMMANDS: connection applist =>connection appli.
E-DOC-CTC- 20061027-0003 v2 .0 Connection Commands 86 connection bind Create a new CONN/NA T applic ation helper/port bind ing. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: connection bind application = <string> port = <port-range> application The name of a CONN /NA T application helper .
E-DOC-CTC-20061 027-0003 v2.0 Connection Commands 87 connection bindlist List the current CONN/NA T application helper/port bindings. SYNT AX: EXAMPLE: RELA TED COMMANDS: connection bindlist =>conn.
E-DOC-CTC- 20061027-0003 v2 .0 Connection Commands 88 connection clean Clean the connection da tabase by forcing tim eouts. SYNT AX: where: EXAMPLE: connection clean [level = <number{0-9}>] level A number betwee n 0 and 9. Represents the desired scrubbing level.
E-DOC-CTC-20061 027-0003 v2.0 Connection Commands 89 connection clear Kill all the connections. SYNT AX: EXAMPLE: connection clear =>connection clear Connection to host lost.
E-DOC-CTC- 20061027-0003 v2 .0 Connection Commands 90 connection config Configure the connection handling. SYNT AX: where: EXAMPLE: connection config [configchangemode = <{i mmediate | delayed}>] [probes = <{disabled | enabled}>] [udptrackmode = <{strict | loose}>] configchangemode Select how configuration changes are handled.
E-DOC-CTC-20061 027-0003 v2.0 Connection Commands 91 connection debug The connection debug commands SYNT AX: where: EXAMPLE: connection debug [trace = <{disabled|enabled}>] trace E nable or disable traces.
E-DOC-CTC- 20061027-0003 v2 .0 Connection Commands 92 connection describe Describe the streams of a connect ion. SYNT AX: where: EXAMPLE: connection describe [id = <number{0-2048}>] id A number between 0 and 2048. Represents the ID of the connection to be described.
E-DOC-CTC-20061 027-0003 v2.0 Connection Commands 93 connection flush Flush the current con nection configuration. SYNT AX: connection flush.
E-DOC-CTC- 20061027-0003 v2 .0 Connection Commands 94 connection info Show all the registered modules with some info. SYNT AX: EXAMPLE: connection info =>connection info Registered connection modules : - Module : FW, holds private data (F:10264 S:6592).
E-DOC-CTC-20061 027-0003 v2.0 Connection Commands 95 connection list Display the currentl y known connection s. SYNT AX: where: EXAMPLE: connection list [nr = <number{1-2048}>] [string = <string>] [beginstring = <string>] nr A number between 1 and 2048.
E-DOC-CTC- 20061027-0003 v2 .0 Connection Commands 96 connection refresh Invalidate all the cached decisions. SYNT AX: connection refresh.
E-DOC-CTC-20061 027-0003 v2.0 Connection Commands 97 connection stats Display the connection and stream statistics. SYNT AX: EXAMPLE: connection stats =>connection stats Connection statistics: ----.
E-DOC-CTC- 20061027-0003 v2 .0 Connection Commands 98 connection timerclear Clear the connection timeout to default. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: connection timercl ear [timer = <{tcpidle|tcpneg|tcpkill|udpidle|udpkill| icmpkill|ipidle|ipkill}>] timer The name of the connecti on idle timer to be reset.
E-DOC-CTC-20061 027-0003 v2.0 Connection Commands 99 connection timerconfig Configure the conn ection timeout handl ing. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: connection timerconfig [timer = <.
E-DOC-CTC- 20061027-0003 v2 .0 Connection Commands 100 connection unbind Delete an existing CONN/NA T application helper/port bindi ng. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: connection unbind application = <string> port = <port-range> application The name of a CONN /NA T application helper .
E-DOC-CTC-20061 027-0003 v2.0 CWMP Commands 101 7 CWMP Commands Introduction This chapter describes the commands of the cwmp (CPE W AN Managemen t Protocol) command grou p. Contents This chapter covers th e following commands: cwmp config Configure the cwmpd as seen fr om the ACS.
E-DOC-CTC- 20061027-0003 v2 .0 CWMP Commands 102 cwmp config Configure the cwmpd as seen from the ACS. SYNT AX: where: cwmp config [state = <{disabled|enabled}>] [mode = <{readonly|full}>].
E-DOC-CTC-20061 027-0003 v2.0 CWMP Commands 103 EXAMPLE: connectionRequest Set the connection request flag of the cwmp daemon. Choose between: > enabled > disabled. The default is enabled . OP TIONAL connectionReqPath Set the path where th e cwmp daemon can be reached.
E-DOC-CTC- 20061027-0003 v2 .0 CWMP Commands 104 cwmp server config Configure the cwmpd towards the ACS. SYNT AX: where: EXAMPLE: cwmp server config [url = <string>] [username = <string>] [password = <string>] url Set the HTTP URL used to contact the ACS server .
E-DOC-CTC-20061 027-0003 v2.0 Debug Commands 105 8 Debug Commands Introduction This chapter describes the commands of the debug comman d group. Contents This chapter covers th e following commands: debug exec Execute a 'T race & Debug' command.
E-DOC-CTC- 20061027-0003 v2 .0 Debug Commands 106 debug exec Execute a 'T race & Debug' command. SYNT AX: where: ! This comman d is for qualifie d personnel onl y . debug exec cmd = <quoted string> cmd A quoted 'T race & Deb u g' command string.
E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 107 9 DHCP Commands Introduction This chapter describ es the commands of the Dynamic Host Config uration Protoc ol (DHCP) command grou p. Contents This chapter covers th e following commands: dhcp client flush Delete al l the DHCP leases.
E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 108 dhcp relay ruledelete Delet e a selection rule from a DHCP forw ard entry . 142 dhcp rule add Add a rule for DHCP condition al selection. 143 dhcp rule debug t raceconfig Modify DHCP ru le trace configuration.
E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 109 dhcp client flush Delete all the DHCP lea ses. SYNT AX: i The flush command does not impact previously saved configurations.
E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 110 dhcp client ifadd Create a DHCP client. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: dhcp client ifadd intf = <string> [defrqoptions = <{disabled|enabled}>] intf The name of the dynamic interface for which a DHCP lease must be created.
E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 111 dhcp client ifattach Activate a DHCP client. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: dhcp client ifattach intf = <string> intf The name of the dyn amic interface for which a DHCP client was created.
E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 112 dhcp client ifconfig Configure a DHCP client. SYNT AX: where: RELA TED COMMANDS i Use the command :dhcp cli ent ifrele ase before configurin g the dhcp client.
E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 113 dhcp client ifdelete Delete a DHCP client. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: dhcp client ifdelete intf = <string> intf The name of the dynami c inte rface for which the DHCP lease must be deleted.
E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 114 dhcp client ifdetach De-activate a DHCP client and releases its lease. SYNT AX: where: RELA TED COMMANDS: ifdetach intf = <string> intf The name of the dyn amic interface. REQUIRED dhcp client ifa ttach Activ ate a DHCP client.
E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 115 dhcp client iflist List all the DHCP leases attached to dyna mic interfaces. SYNT AX: where: EXAMPLE: EXAMPLE INPUT/OUTPUT IN A NETWORKED ENVIRONMENT : The Thomson ST is configured as DHCP client di sabled its Ethernet interface eth0.
E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 116 RELA TED COMMANDS: dhcp client ifa dd Create a DHCP client. dhcp client ifdel ete Delete a DHCP client.
E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 117 dhcp client ifrenew Renew the DHCP lease. SYNT AX: where: EXAMPLE 1: dhcp client ifrenew intf = <string> intf The name of the dynami c inte rface for which the DHCP lease must be renewe d. REQUIRED =>dhcp client iflist NewETHoA : [BOUND] flags= uc IP address : 10.
E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 118 EXAMPLE 2: The Thomson ST is configured as DHCP client di sabled its Ethernet interface eth0. RELA TED COMMANDS: =>dhcp client stats DHCP client sta.
E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 119 dhcp client debug clear Clear the DHCP client statistics. SYNT AX: EXAMPLE: RELA TED COMMANDS: dhcp client debug clear =>dhcp client debug stats DHCP.
E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 120 dhcp client debug stats Print the DHCP cl ient statistics. SYNT AX: EXAMPLE: RELA TED COMMANDS: dhcp client debug stats =>dhcp client debug stats DH.
E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 121 dhcp client debug traceconfig Modify the DHCP clie nt trace configuration. SYNT AX: where: EXAMPLE: dhcp client debug traceconfig [state = <{disabled | enabled}>] state Enable or disabl e tracing. The default is disabled .
E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 122 dhcp client rqoptions add Add a DHCP Opti on Code to the Parameter Request List. SYNT AX: where: RELA TED COMMANDS: dhcp client rqoptions add intf = <string> option = <string or number> [index = <number{0-255}>] intf The name of the dyn amic interface.
E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 123 dhcp client rqoptions delete Delete a DHCP Option Code from the Parameter Request List. SYNT AX: where: RELA TED COMMANDS: dhcp client rqoptions delete intf = <string> option = <string or number> intf The name of the dyn amic interface.
E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 124 dhcp client rqoptions list List all DHCP Optio n Codes in the Parameter Request List. SYNT AX: where: RELA TED COMMANDS: dhcp client rqoptions list [intf = <string>] intf The name of the d ynamic interface.
E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 125 dhcp client rqoptions optionlist List all DHCP Option Codes that can be used in the Para meter Request List. SYNT AX: RELA TED COMMANDS: dhcp client rqoptions optionlist dhcp client rqoption s add Add a DHCP Option Code to the Parame ter Request List.
E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 126 dhcp client txoptions add Add an option . SYNT AX: where: EXAMPLE: RELA TED COMMANDS: dhcp client txoptions add intf = <string> option = <stri.
E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 127 dhcp client txoptions delete Delete an option. SYNT AX: where: RELA TED COMMANDS: dhcp client txoptions delete intf = <string> option = <string or number> intf The name of the d ynamic interface.
E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 128 dhcp client txoptions list List all options. SYNT AX: RELA TED COMMANDS: dhcp client txoptions list dhcp client txoptio ns delete Delete an option.
E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 129 dhcp client txoptions optionlist Lists all DHCP Option C odes that can be used. SYNT AX: RELA TED COMMANDS: dhcp client txoptions optionlist dhcp client txoptio ns add Add an option. dhcp client txop tions list List all options.
E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 130 dhcp relay add Add an entry to the DHCP forward list. SYNT AX: where: RELA TED COMMANDS: dhcp relay add name = <string> name The forward entry name. REQUIRED dhcp relay delete Delete an entry from the DHCP forward list.
E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 131 dhcp relay debug stats Show the DHCP relay statistics. SYNT AX: EXAMPLE: RELA TED COMMANDS: dhcp relay debug stats =>dhcp relay debug stats DHCP rela.
E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 132 dhcp relay debug traceconfig Modify the DHCP relay trace configur ation. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: dhcp relay debug traceconfig [state = <{disabled | enabled}>] state Enable or disabl e tracing.
E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 133 dhcp relay config Set the DHCP relay con figuration settings. SYNT AX: where: EXAMPLE: dhcp relay config [agentinfo = <{disabled | enabled}>] [agentmismatch = <{disabled | enabled}>] agentinfo Set the relay ag ent info status (RFC3 046) enabled or disabled.
E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 134 dhcp relay delete Delete an entry from the DHCP forward list. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: dhcp relay delete name = <string> name The forward entry name. REQUIRED =>dhcp relay delete name = lan1_to_127.
E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 135 dhcp relay flush Flush the DHCP relay settings. SYNT AX: EXAMPLE: i The flush command does not im pact previously saved configurations. dhcp relay flush =>dhcp relay list DHCP server Interface giaddr ------------------------------------------------------- 127.
E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 136 dhcp relay ifconfig Configure a DHCP relay interface. SYNT AX: where: dhcp relay ifconfig intf = <string> [relay = <{disabled | enabled}>] .
E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 137 EXAMPLE: =>dhcp relay iflist eth0 : admin state = up oper state = up max hops = 4 trusted = disabled remote id = Internet_trigger : admin state = dow.
E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 138 dhcp relay iflist Show the configuration of the relay interfaces. SYNT AX: where: EXAMPLE: dhcp relay iflist [intf = <string>] intf The name of the d ynamic interface to be lis ted. Note If not specified, all the relay in terfaces will be shown.
E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 139 dhcp relay list List the DHCP forward list. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: dhcp relay list [name = <string>] name The forward entry name. OP TIONAL =>dhcp relay list DHCP server Interface giaddr ------------------------------------------------------- 127.
E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 140 dhcp relay modify Modify an entry from the DHCP forward list. SYNT AX: where: RELA TED COMMANDS: dhcp relay modify name = <string> [addr = <ip.
E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 141 dhcp relay ruleadd Add a selection rule to a DHCP forward entry . SYNT AX: where: RELA TED COMMANDS: dhcp relay ruleadd name = <string> [key = <{or | and}>] rulename = <string> name The name of the forward entry .
E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 142 dhcp relay ruledelete Delete a selection rule from a DHCP forward entry . SYNT AX: where: RELA TED COMMANDS: dhcp relay ruledelete name = <string> rulename = <string> name The name of the forward entry .
E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 143 dhcp rule add Add a rule for DHCP conditional selection. SYNT AX: where: RELA TED COMMANDS: dhcp rule add name = <string> type = <{vci | uci | .
E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 144 dhcp rule debug traceconfig Modify DHCP ru le trace configuration. SYNT AX: where: dhcp rule debug traceconfig [state = {disabled | enabled}] state Set tracing to disabl ed or enable d. The default is disabled .
E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 145 dhcp rule delete Delete a DHCP rule. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: dhcp rule delete name = <string> name The name of the DHCP rule. REQUIRED =>dhcp rule delete name = new :dhcp rule delete name=new => dhcp rule add Add a ru le for DHCP conditional selection.
E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 146 dhcp rule flush Flush all DHCP rules. SYNT AX: EXAMPLE: RELA TED COMMANDS: dhcp rule flush =>dhcp rule list Name Use Value new 0 vci=test =>dhcp rule flush =>dhcp rule list Name Use Value => dhcp rule add Add a ru le for DHCP conditional selection.
E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 147 dhcp rule list List all DHCP rules. SYNT AX: EXAMPLE: RELA TED COMMANDS: dhcp rule list =>dhcp rule list Name Use Value new 0 vci=test => dhcp rule add Add a ru le for DHCP conditional selection. dhcp rule delete Delete a DHCP rule.
E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 148 dhcp server config Print the DHCP server c onfiguration settings . SYNT AX: where: dhcp server config [state = <{disabled | enabled}>].
E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 149 dhcp server flush Flush all DHCP s erver pool and leas e entries. SYNT AX: i The flush command does not impact previously saved configurations.
E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 150 dhcp server policy Print the DHCP serv er policy settings. SYNT AX: where: dhcp server policy [verifyfirst = <disabled|enabled>] [trustclient = &.
E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 151 dhcp server debug clear Clear the DHCP server statistics. SYNT AX: EXAMPLE: RELA TED COMMANDS: dhcp server debug clear =>dhcp server debug stats DHCP.
E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 152 dhcp server debug stats Show the DHCP server statistics. SYNT AX: EXAMPLE: DESCRIPTION: > DHCP server stat e : the state of the DHCP se rver . > Cor r upted pack et recv : the number of corrupted packets (not co mplaint to RFC2131) received from the LAN.
E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 153 > Ping table g ot full : whet her the history lis t of IP addr ess pings got full or not. These pi ngs are sent by th e DHCP server to verify whether the IP address is alr eady in use disabled the LAN or not (:dhcp server policy verifyfirst=yes).
E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 154 dhcp server debug traceconfig Modify the DHCP server trace configuration. SYNT AX: where: EXAMPLE: dhcp server debug traceconfig [state = <{disabled | enabled}>] state Enable or disabl e tracing. The default is disabled .
E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 155 dhcp server lease add Add a DHCP serv er lease. SYNT AX: where: dhcp server lease add clientid = <client-id> pool = <string> [addr = <ip-.
E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 156 EXAMPLE: RELA TED COMMANDS: =>dhcp server lease list Lease Pool TTL State Clientid 0 0.0.0.0 dhcp_pool_1 00:26:40 FREE 00:90:D0:12:34:56 =>dhcp server lease add clientid=01:23:55:67:89:ab pool=Local_pool leasetime=3600 =>dhcp server lease list Lease Pool TTL State Clientid 0 0.
E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 157 dhcp server lease delete Delete a DHCP server lease. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: dhcp server lease delete [clientid = <clientid | none>] [index = <number>] clientid The DHCP client identification stri ng of the DHCP lease.
E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 158 dhcp server lease flush Flush all the DHCP server leases. SYNT AX: where: EXAMPLE: i The flush command does not impact previously saved configurations. dhcp server lease flush [pool = <string>] pool The name of the DHCP server pool to be flushed.
E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 159 dhcp server lease list List all the DHCP server lea ses. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: dhcp server lease list [clientid = <clientid | none>] [index = <number>] clientid The DHCP client identification stri ng of the DHCP lease.
E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 160 dhcp server option flush Flush all DHCP server option templates and instances. SYNT AX: i The flush command does not impact previously saved configurations.
E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 161 dhcp server option instadd Add a DHCP s erver option instance. SYNT AX: where: dhcp server option instadd name = <string> tmplname = <string> value = <Value : (type)value; type being 8- bit, 16-bit, 32-bit, addr, ascii, byte_array> name The name of the DHCP server op tion instance.
E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 162 EXAMPLE: RELA TED COMMANDS: =>dhcp server option instlist myInstance Tmpl name : myTmpl (1) Use : 0 Value : (32-bit)64 =>dhcp server option insta.
E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 163 dhcp server option instdelete Delete a DHCP server option instance. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: dhcp server option instdelete name = <string> name The name of the DHCP server op ti on instance to be d eleted.
E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 164 dhcp server option instlist List all the DHCP serv er option instances. SYNT AX: EXAMPLE: RELA TED COMMANDS: dhcp server option instlist =>dhcp serv.
E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 165 dhcp server option tmpladd Add a DHCP server o ption template. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: dhcp server option tmpladd name = <string&.
E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 166 dhcp server option tmpldelete Delete a DHCP server option template. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: dhcp server option tmpldelete name = <string> name The name of the DHCP server op ti on templa te to be deleted.
E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 167 dhcp server option tmpllist List all the DHCP serv er option templates. SYNT AX: EXAMPLE: RELA TED COMMANDS: dhcp server option tmpllist =>dhcp server option tmpllist Name Option Type Use yourTmpl 2 ascii 0 myTmpl 1 32-bit 0 => dhcp server option tmpladd Ad d a DHCP server option template.
E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 168 dhcp server pool add Add a DHCP server pool. SYNT AX: where: dhcp server pool add name = <string> [index = <number>] name The name of the DHCP server po ol. Note If not specified, the name i s “dhcp_pool_x”, where x is a subsequent number .
E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 169 EXAMPLE: RELA TED COMMANDS: =>dhcp server pool list Pool Start End State PPP 0 dhcp_pool_1 0.0.0.0 0.0.0.0 FREE 1 My_LAN_Pool 10.0.0.1 10.0.0.254 USED 2 dhcp_pool_2 0.0.0.0 0.0.0.0 FREE =>dhcp server pool add =>dhcp server pool list Pool Start End State PPP 0 dhcp_pool_1 0.
E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 170 dhcp server pool config Configure a DHCP server po ol. SYNT AX: where: dhcp server pool config name = <string> intf = <string> [index = <.
E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 171 EXAMPLE: gateway T he IP address of the defa ult gateway for the DHCP clients. The default value of th is parameter is 0 (not speci fied), which means t.
E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 172 dhcp server pool delete Delete a DHCP server pool . SYNT AX: where: EXAMPLE: RELA TED COMMANDS: dhcp server pool delete name = <string> name The name of the DHCP se rver pool to be deleted. Ti p Use the command :dhc p server pool list to obtain a lis t of all current DHCP leases.
E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 173 dhcp server pool flush Flush all DHCP server pools. SYNT AX: EXAMPLE: i The flush command does not impact previously saved configurations. dhcp server pool flush =>dhcp server pool list Pool Start End Intf State 0 LAN_Private 10.
E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 174 dhcp server pool list List all DHCP server po ols. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: dhcp server pool list [name = <string>] name The name of the DHCP server po ol to be shown. Note If not specified, al l the DHCP server pools are shown.
E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 175 dhcp server pool optadd Add an option instance to the DHCP server po ol. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: dhcp server pool optadd name = <string> instname = <string> name The name of the DHCP server pool to which an option instance must be added.
E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 176 dhcp server pool optdelete Delete an option instan ce from the DHCP server pool. SYNT AX: where: dhcp server pool optdelete name = <string> instname = <string> name The name of the DHCP server po ol from which an optio n instance must be deleted.
E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 177 EXAMPLE: RELA TED COMMANDS: =>dhcp server pool list name=dhcp_pool_1 Pool Start End Intf State 1 dhcp_pool_1 0.0.0.0 0.0.0.0 lan1 FREE DHCP server = 0.0.0.0 [unnumbered] Netmask = 0.0.0.0 Leasetime = infinite Gateway = 0.
E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 178 dhcp server pool rtadd Add a route to the DHCP server pool. SYNT AX: where: RELA TED COMMANDS: dhcp server pool rtadd name = <string> dst = <i.
E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 179 dhcp server pool rtdelete Delete a route from the DHCP server pool. SYNT AX: where: RELA TED COMMANDS: dhcp server pool rtdelete name = <string> d.
E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 180 dhcp server pool ruleadd Add a selection rule to th e DHCP ser ver pool. SYNT AX: where: RELA TED COMMANDS: dhcp server pool ruleadd name = <string> [key = {or | and}] rulename = <string> name The name of the DHCP server pool to which a selection rule must be added.
E-DOC-CTC-20061 027-0003 v2.0 DHCP Commands 181 dhcp server pool ruledelete Delete a sele ction rule from the DHCP se rver pool. SYNT AX: where: RELA TED COMMANDS: dhcp server pool ruleadd name = <string> rulename = <string> name The name of the DHCP server po ol from which a selection rule must be deleted.
E-DOC-CTC- 20061027-0003 v2 .0 DHCP Commands 182.
E-DOC-CTC-20061 027-0003 v2.0 DNS Commands 183 10 DNS Commands Introduction This chapter describes the commands of the dns comman d group. Contents This chapter covers th e following commands: dns client config Modify the Domain Name System (DNS) resolver configura tion.
E-DOC-CTC- 20061027-0003 v2 .0 DNS Commands 184 dns client config Modify the Domain Name System (DNS) resolver configuration. SYNT AX: where: EXAMPLE: dns client config [timeout = <number{1-900}>.
E-DOC-CTC-20061 027-0003 v2.0 DNS Commands 185 dns client dnsadd Add a DNS server . SYNT AX: where: EXAMPLE: RELA TED COMMANDS: dns client dnsadd addr = <string> [port = <number>] addr The IP addre ss of the DNS server to be adde d. REQUIRED port The DNS server port number .
E-DOC-CTC- 20061027-0003 v2 .0 DNS Commands 186 dns client dnsdelete Delete a DNS server . SYNT AX: where: EXAMPLE: RELA TED COMMANDS: dns client dnsdelete index = <number{1-99}> index A numb er between 1 and 99. Represents the index number of the DNS server to be deleted.
E-DOC-CTC-20061 027-0003 v2.0 DNS Commands 187 dns client dnslist List all DNS servers. SYNT AX: EXAMPLE: RELA TED COMMANDS: dns client dnslist =>dns client dnslist Entry State Family Server 1 CONNECTED IP [port] 53 - [addr] 127.0.0.1 2 CONNECTED IP [port] 53 - [addr] 150.
E-DOC-CTC- 20061027-0003 v2 .0 DNS Commands 188 dns client flush Remove all DNS servers. SYNT AX: dns client flush.
E-DOC-CTC-20061 027-0003 v2.0 DNS Commands 189 dns client nslookup DNS lookup for a dom ain name or an addre ss. SYNT AX: where: dns client nslookup host = <string> host T he DNS domain name string for which to query .
E-DOC-CTC- 20061027-0003 v2 .0 DNS Commands 190 dns server config Modify the DNS resolver confi guration. SYNT AX: where: EXAMPLE: dns server config [domain = <string>] [timeout = <number{0-2.
E-DOC-CTC-20061 027-0003 v2.0 DNS Commands 191 dns server flush Flush all local DN S hosts and routes. SYNT AX: dns server flush.
E-DOC-CTC- 20061027-0003 v2 .0 DNS Commands 192 dns server debug clear Clear the DNS server/f orwarder statistics. SYNT AX: EXAMPLE: RELA TED COMMANDS: dns server debug clear =>dns server debug sta.
E-DOC-CTC-20061 027-0003 v2.0 DNS Commands 193 dns server debug stats Print the DNS server/f orwarder statistics. SYNT AX: EXAMPLE: RELA TED COMMANDS: dns server debug stats =>dns server debug stat.
E-DOC-CTC- 20061027-0003 v2 .0 DNS Commands 194 dns server debug spoof clear Clear the intercept cache table SYNT AX: RELA TED COMMANDS: dns server debug spoof clear dns server debug spoof getaddress .
E-DOC-CTC-20061 027-0003 v2.0 DNS Commands 195 dns server debug spoof getaddress Get the real ip for the given spoofed ip SYNT AX: where: EXAMPLE: RELA TED COMMANDS: dns server debug spoof getaddress addr = <ip-address> addr The IP ad dress of the spoofed server .
E-DOC-CTC- 20061027-0003 v2 .0 DNS Commands 196 dns server debug spoof getflags Get the error flags for the given spoofed ip SYNT AX: where: EXAMPLE: RELA TED COMMANDS: dns server debug spoof getflags addr = <ip-address> addr The IP ad dress of the spoofed server .
E-DOC-CTC-20061 027-0003 v2.0 DNS Commands 197 dns server debug spoof list List the intercept cache table. SYNT AX: EXAMPLE: RELA TED COMMANDS: dsn server debug spoof list {Administrator}[dns server debug spoof]=>list Spoof IP FQDN Real IP Flags 198.
E-DOC-CTC- 20061027-0003 v2 .0 DNS Commands 198 dns server debug spoof update Update the interc ept cache table. SYNT AX: EXAMPLE: RELA TED COMMANDS: dns server debug spoof update {Administrator}=>.
E-DOC-CTC-20061 027-0003 v2.0 DNS Commands 199 dns server host add Add a local DNS host. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: dns server host add name = <string> [addr = <ip-address>] [ttl = <number{0-2147483647}>] name The name of the IP host to be added.
E-DOC-CTC- 20061027-0003 v2 .0 DNS Commands 200 dns server host delete Delete a local DNS host. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: dns server host delete name = <string> name The name of the DNS host to be del eted. REQUIRED =>dns server host list Address Hostname TTL (s) 150.
E-DOC-CTC-20061 027-0003 v2.0 DNS Commands 201 dns server host flush Flush all the local DNS hosts. SYNT AX: EXAMPLE: dns server host flush =>dns server host list Address Hostname TTL (s) 192.
E-DOC-CTC- 20061027-0003 v2 .0 DNS Commands 202 dns server host list List all the local DNS hosts. SYNT AX: EXAMPLE: RELA TED COMMANDS: dns server host list =>dns server host list Address Hostname TTL (s) 192.
E-DOC-CTC-20061 027-0003 v2.0 DNS Commands 203 dns server route add Creates a DNS forwarding entry or template. SYNT AX: where: dns server route add dns = <ip-address> [src = <ip-address>].
E-DOC-CTC- 20061027-0003 v2 .0 DNS Commands 204 EXAMPLE: RELA TED COMMANDS: =>dns server route add dns=150.150.150.150 src=10.0.0.0/8 domain=myDNS intf=eth0 =>dns server route list DNS Server Source Domain Metric Intf State 150.150.150.150 10.0.
E-DOC-CTC-20061 027-0003 v2.0 DNS Commands 205 dns server route delete Deletes a DNS forwa rdi ng entry or template SYNT AX: where: EXAMPLE: RELA TED COMMANDS: dns server route delete dns = <ip-add.
E-DOC-CTC- 20061027-0003 v2 .0 DNS Commands 206 dns server route flush Removes all DNS forwarding entries and templates. SYNT AX: EXAMPLE: dns server route flush =>dns server route list DNS Server Source Domain Metric Intf State 150.150.150.150 10.
E-DOC-CTC-20061 027-0003 v2.0 DNS Commands 207 dns server route list List all the DNS forwardi ng entries or templates. SYNT AX: EXAMPLE: RELA TED COMMANDS: dns server route list =>dns server route list DNS Server Source Domain Metric Intf State 150.
E-DOC-CTC- 20061027-0003 v2 .0 DNS Commands 208.
E-DOC-CTC-20061 027-0003 v2.0 DSD Commands 209 11 DSD Commands Introduction This chapter describes the commands of the dsd comman d group. Contents This chapter covers th e following commands: dsd config Display/modify the Differentia ted Service Delivery (DSD) framework configuration.
E-DOC-CTC- 20061027-0003 v2 .0 DSD Commands 210 dsd config Display/modify the Diffe ren tiated Service Deliver y (DSD) framework configuration. SYNT AX: where: EXAMPLE: dsd config [state = <{disabl.
E-DOC-CTC-20061 027-0003 v2.0 DSD Commands 211 dsd debug config Display/modif y DSD debug settings SYNT AX: where: config [turbomode = <{disabled|enabled}>] turbomode Enable/disable turbom ode O.
E-DOC-CTC- 20061027-0003 v2 .0 DSD Commands 212 dsd debug connection list Display the internal co nnection pool usage. SYNT AX: where: dsd debug connection list [expand = <{disabled|enabled}>] expand Enable or disable the expanded listing. The default is disab led .
E-DOC-CTC-20061 027-0003 v2.0 DSD Commands 213 dsd debug proxy Display/modi fy the HyperT ext T ransfer Proto col (HTTP) Intercep t fixed proxy configu ration.
E-DOC-CTC- 20061027-0003 v2 .0 DSD Commands 214 dsd debug recycling Display/ modify HTTP I recycling settings SYNT AX: where: dsd debug recycling state = <disabled>|<enabled> interval = &l.
E-DOC-CTC-20061 027-0003 v2.0 DSD Commands 215 dsd debug stats Display/clear DSD framework and module statistics SYNT AX: where: dsd debug stats name = <{intercept|urlfilter|recycling|syslog|all} c.
E-DOC-CTC- 20061027-0003 v2 .0 DSD Commands 216 dsd intercept config Display/modify the HTTP Intercept configuration. SYNT AX: where: EXAMPLE: dsd intercept config [WDSpoofedIP = <ip-address>] [.
E-DOC-CTC-20061 027-0003 v2.0 DSD Commands 217 dsd sy slog config Display/modif y the HTTP Intercept logg ing configurat ion. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: dsd syslog config [syslog = <{none | unauthorized | errors | inter- cepted | all}>] syslog Define the type of events to log.
E-DOC-CTC- 20061027-0003 v2 .0 DSD Commands 218 dsd sy slog list Display the HTTP Intercept log file. SYNT AX: EXAMPLE: RELA TED COMMANDS: dsd syslog list =>dsd syslog list <86> SysUpTime: 00:22:37 [HTTPI] src=10.0.0.1 src_port=1965 dst=141.11.
E-DOC-CTC-20061 027-0003 v2.0 DSD Commands 219 dsd urlfilter config Display/modify the URL filtering configuration. SYNT AX: where: EXAMPLE: dsd urlfilter config [state = <{disabled | enabled}>].
E-DOC-CTC- 20061027-0003 v2 .0 DSD Commands 220 dsd urlfilter rule add Add a rule. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: dsd urlfilter rule add url = <string> action = <{block | accept | redirect}> redirect = <string> url Definition of the URL filter .
E-DOC-CTC-20061 027-0003 v2.0 DSD Commands 221 dsd urlfilter rule delete Delete a rule. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: dsd urlfilter rule delete index = <number> [url = <string>] index Insertion po sition in the list. Ti p Use the command :dsd urlfilter rule list to obtain the index number of the rule to be deleted.
E-DOC-CTC- 20061027-0003 v2 .0 DSD Commands 222 dsd urlfilter rule flush Remove all current rules. SYNT AX: EXAMPLE: dsd urlfilter rule flush =>dsd urlfilter rule list Index Action Url Redirect ----- ------ --- -------- 0 redirect www.speedtouch.com www.
E-DOC-CTC-20061 027-0003 v2.0 DSD Commands 223 dsd urlfilter rule list Display the list of curr ent rules. SYNT AX: EXAMPLE: RELA TED COMMANDS: dsd urlfilter rule list =>dsd urlfilter rule list Index Action Url Redirect ----- ------ --- -------- 0 redirect www.
E-DOC-CTC- 20061027-0003 v2 .0 DSD Commands 224 dsd urlfilter rule modify Modify an existing rule. SYNT AX: where: dsd urlfilter rule modify index = <number> [newurl = <string>] action = <{block | accept | redirect}> redirect = <string> index Insertion po sition in the list.
E-DOC-CTC-20061 027-0003 v2.0 DSD Commands 225 EXAMPLE: RELA TED COMMANDS: =>dsd urlfilter rule list Index Action Url Redirect ----- ------ --- -------- 0 redirect www.speedtouch.com www.speedtouch.be 1 accept www.baen.com Rule list statistics : 2 present, 128 total (0.
E-DOC-CTC- 20061027-0003 v2 .0 DSD Commands 226.
E-DOC-CTC-20061 027-0003 v2.0 DynDNS Commands 227 12 DynDNS Commands Introduction Dynamic DNS is a service that allows to bind a ho st name to an IP address. In contra st to classica l DN S, this service allows regular updates of the IP address related to a host name.
E-DOC-CTC- 20061027-0003 v2 .0 DynDNS Commands 228 dyndns add Add a dynamic DNS client. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: dyndns add name = <string> name The name of the new dynamic DNS client. Note A maximum of 5 clients ca n be configured.
E-DOC-CTC-20061 027-0003 v2.0 DynDNS Commands 229 dyndns delete Delete a dynamic DNS client. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: dyndns delete name = <string> name The name of the dynamic DNS client to be dele ted. REQUIRED =>dyndns list WAN : [INIT] user = password = addr = 0.
E-DOC-CTC- 20061027-0003 v2 .0 DynDNS Commands 230 dyndns flush Delete all the dy namic DNS clients. SYNT AX: dyndns flush.
E-DOC-CTC-20061 027-0003 v2.0 DynDNS Commands 231 dyndns list List all the dyna mic DNS clients. SYNT AX: EXAMPLE: RELA TED COMMANDS: dyndns list =>dyndns list WAN : [INIT] user = password = addr = 0.0.0.0 => dyndns add Add a dynamic DNS client.
E-DOC-CTC- 20061027-0003 v2 .0 DynDNS Commands 232 dyndns modify Modify a dynamic DNS client. SYNT AX: where: dyndns modify name = <string> [intf = <string>] [user = <string>] [passw.
E-DOC-CTC-20061 027-0003 v2.0 DynDNS Commands 233 EXAMPLE: status Enable or disabl e the dynamic DNS client. The default is disab led . OPTIONAL trace Enable or disable the verbose console logg ing for the dynamic DNS client. The default is disab led .
E-DOC-CTC- 20061027-0003 v2 .0 DynDNS Commands 234 dyndns host add Add a fully qualified host name. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: dyndns host add group = <string> name = <string> group The dynamic DNS host grou p. Note A maximum of 4 diffe rent groups can be created.
E-DOC-CTC-20061 027-0003 v2.0 DynDNS Commands 235 dyndns host delete Delete a hos t name. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: dyndns host delete name = <string> name The name of the IP host to be deleted. REQU IRED =>dyndns host list local : [ ] localhost.
E-DOC-CTC- 20061027-0003 v2 .0 DynDNS Commands 236 dyndns host flush Delete all hosts. SYNT AX: i The hosts cannot be flushed, if there is still a group referenced to the hosts.
E-DOC-CTC-20061 027-0003 v2.0 DynDNS Commands 237 dyndns host list List all host names. SYNT AX: EXAMPLE: RELA TED COMMANDS: dyndns host list =>dyndns host list local : [ ] localhost.
E-DOC-CTC- 20061027-0003 v2 .0 DynDNS Commands 238 dyndns service list List all dynami c DNS services. SYNT AX: EXAMPLE: dyndns service list =>dyndns service list dyndns : server = members.dyndns.org port = 80 request = /nic/update update interval = 2097120 retry interval = 30 max retry = 3 statdns : server = members.
E-DOC-CTC-20061 027-0003 v2.0 DynDNS Commands 239 RELA TED COMMANDS: dyndns service modify Modify specific dynamic DNS service settings..
E-DOC-CTC- 20061027-0003 v2 .0 DynDNS Commands 240 dyndns service modify Modify specific dynami c DNS service settings. SYNT AX: where: dyndns service modify name = <string> [server = <string.
E-DOC-CTC-20061 027-0003 v2.0 DynDNS Commands 241 EXAMPLE: RELA TED COMMANDS: =>dyndns service modify name=custom server=mydyndns.org port=www-http request=hereiam | updateinterval=2000000 retryinterval=15 max_retry=5 =>dyndns service list dyndns : server = members.
E-DOC-CTC- 20061027-0003 v2 .0 DynDNS Commands 242.
E-DOC-CTC-20061 027-0003 v2.0 Env Commands 243 13 Env Commands Introduction This chapter describes the commands of the env comman d group. Contents This chapter covers th e following commands: env flush Flush all the non-system e nvironment variables.
Env Commands E-DOC-CTC- 20061027-0003 v2 .0 244 env flush Flush all the non-system environment variables. SYNT AX: env flush.
Env Commands E-DOC-CTC-20061 027-0003 v2.0 245 env get Get the current value of an environment variable. SYNT AX: where: RELA TED COMMANDS: env get var = <string> var The name of th e environme nt variable. Ti p Use th e command :env list to obtain a list of all environ- ment variables.
E-DOC-CTC- 20061027-0003 v2 .0 Env Commands 246 env list Show all the currently availa ble environment variables. SYNT AX: RELA TED COMMANDS: env list env get Get the current value of an environment variable.
E-DOC-CTC-20061 027-0003 v2.0 Env Commands 247 env set Set an environment variable. SYNT AX: where: EXAMPLE: For infinite TELN ET time out, set the val ue of the variable SESSIONTIMEOUT to “0”: RELA TED COMMANDS: env set var = <string> value = <translated string> var The name of th e environme nt variable.
E-DOC-CTC- 20061027-0003 v2 .0 Env Commands 248 env unset Delete a environment variable. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: env unset var = <string> var The name of the environment variable to be deleted.
E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 249 14 Eth Commands Introduction This chapter describes the commands of the eth comman d group. Contents This chapter covers th e following commands: eth ifadd Create a new ETH interfac e. 252 eth ifattach Attach an E TH interface.
E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 250 eth bridge igmpsnooping ifconfi g Configure the brid ge interface‘s IGMP snoopi ng flags and mode 282 eth bridge igmpsnooping iflist Display a bridge .
E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 251 eth vlan flush Flush all VLANs. 325 eth vlan list Display all VLAN s. 326.
E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 252 eth ifadd Create a new ETH interface. SYNT AX: where: RELA TED COMMANDS: eth ifadd intf = <string> intf The name of the new ETH in terface. REQUIRED eth ifdelete Delete an ETH interface. eth iflist Display the ETH interfaces .
E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 253 eth ifattach Attach an ETH interf ace. SYNT AX: where: RELA TED COMMANDS: eth ifattach intf = <string> intf The name of the ETH interf ace to be attached. REQUIRED eth ifdetach Detach an ETH interface.
E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 254 eth ifconfig Modify an ETH interfac e. SYNT AX: where: eth ifconfig intf = <string> [dest = <string>] [retry = <number{0-65535}>] [vlan = <string>] intf The name of the ETH interface to be con figured.
E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 255 eth ifdelete Delete an ETH interface. SYNT AX: where: RELA TED COMMANDS: eth ifdelete intf = <string> intf The name of the ETH interface name to be d eleted. REQUIRED eth ifadd Create a new ETH interface.
E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 256 eth ifdetach Detach an ETH interface. SYNT AX: where: RELA TED COMMANDS: eth ifdetach intf = <string> intf The name of the ETH interf ace to be detached. REQUIRED eth ifattach Attach an ETH interface.
E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 257 eth iflist Display the ETH interfaces. SYNT AX: where: RELA TED COMMANDS: eth iflist [intf = <string>] [string = <string>] [beginstring = <string>] intf The name of the ETH in terface to be displayed.
E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 258 eth flush Flush all the ETH interfaces. SYNT AX: i The flush command does not impact previo usly saved configurations.
E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 259 eth bridge clear Clear the bridge statistics. SYNT AX: eth bridge clear.
E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 260 eth bridge list Display the current bridge instances Syntax where eth bridge list [brname = <{brid ge}>] [string = <string>] [beginstring = .
E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 261 eth bridge add Add a new bridge instance Syntax where eth bridge add brname=<string> brname The na me of the new bridge instance REQUIRED.
E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 262 eth bridge delete Delete a bridge instance Syntax where eth bridge delete brname = <{bridge}> brname The name of the brid ge instance to be delete.
E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 263 eth bridge select Select the default bridge to configure interfaces (when not sett ing a bridge name, for legacy purposes).
E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 264 eth bridge config Modify/display the brid ge configuration setting s. SYNT AX: where: eth bridge config [brname = <{bridge}>] [age = <number{10.
E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 265 eth bridge dynvlan actlist Display the active MAC entries fo r the dynamic VL AN membership. SYNT AX: RELA TED COMMANDS: eth bridge dynvlan actlist eth bridge dynvlan add Add a dynamic VLAN membership entry .
E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 266 eth bridge dynvlan add Add a dynamic VLAN membership entry . SYNT AX: where: RELA TED COMMANDS: eth bridge dynvlan add [id = <number{0-100000}>] hwaddr = <masked-hardware-address> vlan = <string> [remvlan = <{default}>] id A number between 0 and 100000.
E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 267 eth bridge dynvlan config Modify the d ynamic VLAN membe rship configurati on. SYNT AX: where: RELA TED COMMANDS: eth bridge dynvlan config [timeout = <number{0-100000}>] timeout A numb er betwee n 0 and 100000 (seconds).
E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 268 eth bridge dynvlan delete Delete a dynamic VLAN membership entry . SYNT AX: where: RELA TED COMMANDS: eth bridge dynvlan delete id = <number{0-100000}> id A number between 0 and 100000. Represents the id of a dynamic VLAN membership.
E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 269 eth bridge dynvlan flush Flush all dyna mic VLAN membership entries. SYNT AX: eth bridge dynvlan flush.
E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 270 eth bridge dynvlan list Display a dynamic VLAN membership entry . SYNT AX: RELA TED COMMANDS: eth bridge dynvlan list eth bridge dynvlan actlist Display the active MAC entries fo r the dyna mic VL AN me mbership.
E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 271 eth bridge flush Flush bridge interfaces and parameters. SYNT AX: i The flush comman d does not impact previously saved configurations.
E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 272 eth bridge ifadd Add a new bridge interface. SYNT AX: where: RELA TED COMMANDS: eth bridge ifadd [brname = <{brid ge}>] intf = <string> brname The na me of a bridge instan ce. OPTIONAL intf The name of the new br idge interface.
E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 273 eth bridge ifattach Attach a bridge interface. SYNT AX: where: RELA TED COMMANDS: eth bridge ifattach [brname = <{bridge}>] intf = <string> brname The na me of a bridge instan ce. OPTIONAL intf The name of the bridge interface to b e attached.
E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 274 eth bridge ifconfig Modify a bridge interface configuratio n. SYNT AX: where: eth bridge ifconfig [brname = <{bridge}>] intf = <string> [des.
E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 275 ipprec The IP precedence for this interface. Choose between: > disabled > preceden ce > dscp. The default is disab led . OP TIONAL priority A number between 0 and 7. Represents the default priori ty for tagging egress packe ts.
E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 276 eth bridge ifdelete Delete a bridge interface. SYNT AX: where: RELA TED COMMANDS: eth bridge ifdelete [brname = <{bridge}>] intf = <string> brname The na me of a bridge instan ce. OPTIONAL intf The name of the bridge interf ace na me to be deleted.
E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 277 eth bridge ifdetach Detach a bridge interface. SYNT AX: where: RELA TED COMMANDS: eth bridge ifdetach [brname = <{bridge}>] intf = <string> brname The na me of a bridge instan ce. OPTIONAL intf The name of the bridge interface to b e detached.
E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 278 eth bridge iflist Display the current bridge interfaces. SYNT AX: where: RELA TED COMMANDS: eth bridge iflist [brname = <{bridge}>] [intf = <string>] [string = <string>] [beginstring = <string>] brname The na me of a bridge instan ce.
E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 279 eth bridge ifflush Flush the br idge interfac es: detach/delete all interfa ces. SYNT AX: where: eth bridge ifflush [brname = <{bridge}>] brname The na me of a bridge instan ce.
E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 280 eth bridge igmpsnooping config Configure the bridge instance‘ s IGMP Snooping flag s Syntax where: eth bridge igmpsnooping config [brname = <{bridg.
E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 281 eth bridge igmpsnooping list Display a brid ge instance‘s snooped group s. Syntax where: eth bridge igmpsnooping list [brname = <{bridge}>] brnam.
E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 282 eth bridge igmpsnooping ifconfig Configure the bridge in terface‘s IGMP snoopi ng flags and mode. Syntax where: eth bridge igmpsnooping ifconfig [brna.
E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 283 eth bridge igmpsnooping iflist Display a bridge i nterface‘s IGMP status Syntax where: Display bridge interface IGMP status [brname = <{bridge}>].
E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 284 eth bridge igmpsnooping clear Clear the snooping statistics. Syntax where: eth bridge igmpsnooping clear [brname = <{bridge}>] [intf = <{interf.
E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 285 eth bridge macadd Add a static MAC address to a bridge interface. This command allows to manually add static MA C addresses, which should normally be dynamically discovered by the bridge itself.
E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 286 EXAMPLE: RELA TED COMMANDS: =>eth bridge maclist 00:10:a4:ad:32:cf -- dynamic, ethport1, 300 seconds 00:90:d0:8b:fc:2c -- permanent 01:00:5e:00:00:67.
E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 287 eth bridge macdelete Remove a MAC address from th e filtering database. SYNT AX: where: EXAMPLE: eth bridge macdelete [brname = <{bridge}>] hwaddr = <hardware-address> [vlan = <string>] brname The na me of a bridge instan ce.
E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 288 RELA TED COMMANDS: eth bridge macadd Add a static MAC address to a bridge interface. eth bridge maclist Display the MAC address database.
E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 289 eth bridge maclist Display the MAC address database. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: eth bridge maclist [brname = <{bridge}>] brname The na me of a bridge instan ce.
E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 290 eth bridge mcdadd Add a multicast group to be dropped to the database. SYNT AX: where: RELA TED COMMANDS: eth bridge mcdadd [brname = <{bridge}>] .
E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 291 eth bridge mcddelete Delete a multic ast group to be dropped from the database. SYNT AX: where: RELA TED COMMANDS: eth bridge mcddelete [brname = <{bridge}>] brname The na me of a bridge instan ce. OPTIONAL eth bridge mcdadd Add a multicast group to be dropped to the database.
E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 292 eth bridge mcdlist Display the multic ast group to be droppe d from the database. SYNT AX: RELA TED COMMANDS: eth bridge mcdlist eth bridge mcdadd Add a multicast group to be dropped to the database. eth bridge mcddelete Del ete a multicast group to be drop ped from the database.
E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 293 eth bridge rule add Add a new constraint to th e VLAN learning system. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: eth bridge rule add type = <{shared | independent}> vlan = <string> [vlan2 = <string>] [isi = <number{0-32}>] type T y pe of constraint.
E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 294 eth bridge rule delete Delete a constraint from the VLAN learning system. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: eth bridge rule delete index = <number{0-32}> index Index of the constrain t to be dele ted.
E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 295 eth bridge rule flush Flush all constraints from the VLAN learning system. SYNT AX: eth bridge rule flush.
E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 296 eth bridge rule list Display all constraints from the VLAN lear ning system. SYNT AX: EXAMPLE: RELA TED COMMANDS: eth bridge rule list =>eth bridge r.
E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 297 eth bridge vlan ifadd Add a bridge interface to a VLAN. SYNT AX: where: RELA TED COMMANDS: eth bridge vlan ifadd name = <string> intf = <string> [untagged = <{disabled | enabled}>] name The VLAN name to which a bri dge interface must be added.
E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 298 eth bridge vlan ifconfig Modify a bridge interface from a VLAN. SYNT AX: where: RELA TED COMMANDS: eth bridge vlan ifconfig name = <string> intf = <string> untagged = <{disabled | enabled}> name The VLAN name for which a bridge interface must be modifie d.
E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 299 eth bridge vlan ifdelete Delete a bridge interf ace from a VLAN. SYNT AX: where: RELA TED COMMANDS: eth bridge vlan ifdelete name = <string> intf = <string> name The VLAN name for which a bridge interface must be deleted.
E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 300 eth bridge vlan iflist Display all VLANs . SYNT AX: RELA TED COMMANDS: eth bridge vlan iflist eth bridge vlan ifadd Add a bridge interface to a VLAN. eth bridge vlan ifconfig Modify a bridge interface from a VLAN.
E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 301 eth device ifconfig Configure an Ethe rnet interface. SYNT AX: where: eth device ifconfig intf = <string> [type = <{auto | 10BaseTHD | 10BaseTFD | 100BaseTHD| 100BaseTFD} or number>] [state = <{enabled | disabled}>] intf The name of a phys ical interface.
E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 302 EXAMPLE: RELA TED COMMANDS: =>eth device iflist Interface Type Result State ethif1 auto 100BaseTFD UP [forwarding] ethif2 auto 100BaseTFD UP [forward.
E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 303 eth device iflist Show status of Ethernet interfaces. SYNT AX: EXAMPLE: DESCRIPTION: > Ty p e : Indicates the configured Eth ernet communication speed and duplex mode. > Result : Indicates the effective op erating status if T ype e quals “auto” .
E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 304 eth switch group flush Set all the ports to the default settings. All the ports are placed in group 0. SYNT AX: EXAMPLE: RELA TED COMMANDS: eth switch g.
E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 305 eth switch group list List all the configured swi tch groups. SYNT AX: EXAMPLE: RELA TED COMMANDS: eth switch group list =>eth switch group list Group 0 Ports: 4 Group 1 Ports: 1 Group 2 Ports: 2 3 => eth switch group fl ush Set all the ports to the default settings.
E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 306 eth switch group move Move a specified port t o a specified switch group. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: eth switch group move group = <number{0-3}> port = <number{1-4}> group A number be tween 0 and 4.
E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 307 eth switch mirror capture Define the specified port to be th e Mirror Capture Port. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: i Only one port can be th e Mirror Capture Port at any one time. eth switch mirror capture port = <number{1-4}> port The port to be th e Mirror Capture Port.
E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 308 eth switch mirror egress Enable or disab le the specified port to be the Mirror Egress Po rt. SYNT AX: where: EXAMPLE: Here port 1 is enable d as Mirror Egress Port Here port 1 is disabled as Mirror Egress Port RELA TED COMMANDS: i Only one port can be th e Mirror Egress Port at any one t ime.
E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 309 eth switch mirror ingress Enable or disab le the specified port to be the Mirror Ingress Port. SYNT AX: where: EXAMPLE: Here port 2 is enable d as Mirror Ingress Port Here port 2 is disabled as Mirror Ingress Port RELA TED COMMANDS: i Only one port can be th e Mirror Ingress Port at any one time.
E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 310 eth switch share add Add a port to be shared. SYNT AX: where: RELA TED COMMANDS: eth switch share add port = <number{1-4}> shared = <number{1-4}> port A number between 1 and 4. Represents the port.
E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 311 eth switch share delete Delete a shared port. SYNT AX: where: RELA TED COMMANDS: eth switch share delete port = <number{1-4}> shared = <number{1-4}> port A number between 1 and 4. Represents the port.
E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 312 eth switch share list Display shared ports. SYNT AX: RELA TED COMMANDS: eth switch share list eth switch share add Add a port to be shared .
E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 313 eth switch info Display switch capabilities. SYNT AX: RELA TED COMMANDS: Not applicable eth switch info.
E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 314 eth switch qos config Configure common qos parame ters. SYNT AX: where: RELA TED COMMANDS: eth switch qos config state = <disabled|enabled> [nbrOf.
E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 315 eth switch qos ifconfig Configure per port QoS parameters. SYNT AX: where: RELA TED COMMANDS: eth switch qos ifconfig port = <number{1-4}> mode = <802.
E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 316 eth switch qos list Display QoS configuratio n. SYNT AX: RELA TED COMMANDS: eth switch qos list eth switch qos config Conf igure common qos parameters. eth switch qos ifconfig Configure per port QoS parameters.
E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 317 eth switch qos weights Configure the queue weights. SYNT AX: where: RELA TED COMMANDS: eth switch qos weights queue0 = <number{0-100}> queue1 = <.
E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 318 eth switch shaper config Configure common ing re ss shaper parameters. SYNT AX: where: RELA TED COMMANDS: eth switch shaper config shaper = <number{0.
E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 319 eth switch shaper ifconfig Configure per port shaper parameters. SYNT AX: where: RELA TED COMMANDS: eth switch shaper ifconfig port = <number{1-4}>.
E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 320 eth switch shaper iflist Display shaper conf iguration per port. SYNT AX: RELA TED COMMANDS: eth switch shaper iflist eth switch shaper config Configur e common ingress sh aper parameters. eth switch shaper ifconf ig Config ure per port shaper parameters.
E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 321 eth switch storm ifconfig Configure per port storm con trol parameters. SYNT AX: where: RELA TED COMMANDS: eth switch storm ifconfig port = <number{1-.
E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 322 eth switch storm iflist Display storm control configuration per port. SYNT AX: RELA TED COMMANDS: eth switch storm iflist eth switch storm ifconfig Configure per port storm control param eters.
E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 323 eth vlan add Add a new VLAN. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: eth vlan add name = <string> vid = <number{2-4094}> [addrule = <{disabled | enabled}>] name The new VLAN name. REQUIRED vid A numb er representing th e new VLAN ID.
E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 324 eth vlan delete Delete a V LAN. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: eth vlan delete name = <string> name T he name of the VLAN to be de leted.
E-DOC-CTC-20061 027-0003 v2.0 Eth Commands 325 eth vlan flush Flush all VLA Ns. SYNT AX: EXAMPLE: i All the VLANs, except the de fault VLAN will be flushed.
E-DOC-CTC- 20061027-0003 v2 .0 Eth Commands 326 eth vlan list Display all VLANs . SYNT AX: EXAMPLE: RELA TED COMMANDS: eth vlan list =>eth vlan list Vid Name --- ---- 1 default 2 myVLAN => eth vlan add Add a new VLAN. eth vlan del ete Delete a VLAN.
E-DOC-CTC-20061 027-0003 v2.0 Expr Commands 327 15 Expr Commands Introduction This chapter describes the commands of the expr command group. Contents This chapter covers th e following commands: expr add Add a subexpression to an expression. 328 expr delete Delete an expression.
E-DOC-CTC- 20061027-0003 v2 .0 Expr Commands 328 expr add Add a subexp re ssion to an expression. SYNT AX: where: expr add name = <string> type = <{intf | ip | serv}> addr [!]= <ip-rang.
E-DOC-CTC-20061 027-0003 v2.0 Expr Commands 329 intfgroup The IP interface group. Choose between: > wan > local > lan > tunnel > dmz > guest. Note Only for expression ty pe intf . OP TIONAL tos A number between 0 and 25 5. Represents the T ype of Service (T oS) specification in the IP packet.
E-DOC-CTC- 20061027-0003 v2 .0 Expr Commands 330 icmpcode A nu mber between 0 and 15 . Represents the ICMP code (or begi nning of range) of the packet.
E-DOC-CTC-20061 027-0003 v2.0 Expr Commands 331 EXAMPLE: RELA TED COMMANDS: =>expr list name type use flags expression ------------------------------------------------------------------------------------------ _myPPP_ppp intf 0 D 1. intf=myPPP_ppp _eth0 intf 0 D 1.
E-DOC-CTC- 20061027-0003 v2 .0 Expr Commands 332 expr delete Delete an expression. SYNT AX: where: expr delete name = <string> [index = <number>] name The name of the expression to be deleted. REQUIRED index The index of the subexpression to be deleted.
E-DOC-CTC-20061 027-0003 v2.0 Expr Commands 333 EXAMPLE: RELA TED COMMANDS: =>expr list name type use flags expression ------------------------------------------------------------------------------------------ _myPPP_ppp intf 0 D 1. intf=myPPP_ppp _eth0 intf 0 D 1.
E-DOC-CTC- 20061027-0003 v2 .0 Expr Commands 334 expr flush Flush all the expressions. SYNT AX: expr flush.
E-DOC-CTC-20061 027-0003 v2.0 Expr Commands 335 expr list List the expressions. SYNT AX: where: expr list [name = <string>] [type = <{intf | ip | serv}>] [format = <{pretty | cli}>] [string = <string>] [beginstring = <string>] name The na me of an existing expression .
E-DOC-CTC- 20061027-0003 v2 .0 Expr Commands 336 EXAMPLE 1: =>expr list name type use flags expression ------------------------------------------------------------------------------------------ _Internet intf 0 D 1. intf=Internet _LocalNetwork intf 0 D 1.
E-DOC-CTC-20061 027-0003 v2.0 Expr Commands 337 EXAMPLE 2: =>expr list format=cli :expr add name=_Internet type=intf intf=Internet :expr add name=_LocalNetwork type=intf intf=LocalNetwork :expr add.
E-DOC-CTC- 20061027-0003 v2 .0 Expr Commands 338 RELA TED COMMANDS: expr add Add a subexpression to an expression. expr delete Delete an expression..
E-DOC-CTC-20061 027-0003 v2.0 Expr Commands 339 expr modify Modify an expression. SYN T AX: where: expr modify name = <string> type = <{intf | ip | serv}> index = <number> addr [!]= .
E-DOC-CTC- 20061027-0003 v2 .0 Expr Commands 340 intfgroup The IP interface group. Choose between: > wan > local > lan > tunnel > dmz > guest. Note Only for expression ty pe intf . OP TIONAL bridgeport The bridge port number . Note Only for expression ty pe intf .
E-DOC-CTC-20061 027-0003 v2.0 Expr Commands 341 icmpcode A nu mber between 0 and 15 . Represents the ICMP code (or begi nning of range) of the packet. OP TIONAL icmpcodeend A number between 0 and 15.
E-DOC-CTC- 20061027-0003 v2 .0 Expr Commands 342.
E-DOC-CTC-20061 027-0003 v2.0 Firewall Commands 343 16 Firewall Commands Introduction This chapter describes the commands of the firewa ll command grou p. Contents This chapter covers th e following commands: firewall config Configure the firewall options.
E-DOC-CTC- 20061027-0003 v2 .0 Firewall Commands 344 firewall config Configure the fi rewall op tions. SYNT AX: where: firewall config [state = <{disabled | enabled}>] [keep = <{disabled | en.
E-DOC-CTC-20061 027-0003 v2.0 Firewall Commands 345 EXAMPLE: logdefault Disable or enable logging of d efault firewall rule. The defaul t is disabled . OP TIONAL logthreshol d Disable or enable lo g thresholdi ng. The defaul t is enabled . OP TIONAL tcpwindow A number be twe en 0 and 1073725440.
E-DOC-CTC- 20061027-0003 v2 .0 Firewall Commands 346 firewall clear Flush the firewall configuration. SYNT AX: firewall clear.
E-DOC-CTC-20061 027-0003 v2.0 Firewall Commands 347 firewall list List the firewall configuratio n. SYNT AX: where: firewall list [format = <{pretty | cli}>] format Select the output format in which the config uration must be shown. Choose between: > pr etty : the configuration is shown as intuitive output in clear text.
E-DOC-CTC- 20061027-0003 v2 .0 Firewall Commands 348 EXAMPLE of output in text mode: EXAMPLE of output in CLI mode: =>firewall list Config ====== State : enabled Keep : disabled TcpChecks : exact T.
E-DOC-CTC-20061 027-0003 v2.0 Firewall Commands 349 firewall chain add Add a chain. SYNT AX: where: firewall chain add chain = <string> chain The name of the chai n to be added.
E-DOC-CTC- 20061027-0003 v2 .0 Firewall Commands 350 EXAMPLE: RELA TED COMMANDS: =>firewall chain list Chains ====== Name Description ---------------------------------------------------------------.
E-DOC-CTC-20061 027-0003 v2.0 Firewall Commands 351 firewall chain delete Delete a chain. SYNT AX: where: firewall chain delete chain = <string> chain The name of the chain to be deleted.
E-DOC-CTC- 20061027-0003 v2 .0 Firewall Commands 352 EXAMPLE: RELA TED COMMANDS: =>firewall chain list Chains ====== Name Description ---------------------------------------------------------------.
E-DOC-CTC-20061 027-0003 v2.0 Firewall Commands 353 firewall chain flush Flush all chains. SYNT AX: firewall chain flush.
E-DOC-CTC- 20061027-0003 v2 .0 Firewall Commands 354 firewall chain list List all chains. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: firewall chain list [format = <{pretty | cli}>] format Select the output format in which the chains must be shown.
E-DOC-CTC-20061 027-0003 v2.0 Firewall Commands 355 firewall debug clear Clear the firewall statistics. SYNT AX: EXAMPLE: RELA TED COMMANDS: firewall debug clear =>firewall debug stats Statistics =.
E-DOC-CTC- 20061027-0003 v2 .0 Firewall Commands 356 firewall debug stats Display the firewall statistics. SYNT AX: EXAMPLE: RELA TED COMMANDS: firewall debug stats =>firewall debug stats Statistic.
E-DOC-CTC-20061 027-0003 v2.0 Firewall Commands 357 firewall debug traceconfig Configure the firewa ll trace options. SYNT AX: where: EXAMPLE: firewall debug traceconfig [tcpchecks = <{disabled | e.
E-DOC-CTC- 20061027-0003 v2 .0 Firewall Commands 358 firewall level add Add a security level. SYNT AX: where: RELA TED COMMANDS: firewall level add name = <string> [index = <number>] [read.
E-DOC-CTC-20061 027-0003 v2.0 Firewall Commands 359 firewall level delete Delete a security level. SYNT AX: where: RELA TED COMMANDS: firewall level delete name = <string> name The name of the security le vel to be deleted. REQU IRED firewall level add Add a security level.
E-DOC-CTC- 20061027-0003 v2 .0 Firewall Commands 360 firewall level flush Flush the se curity level configuration. SYNT AX: firewall level flush.
E-DOC-CTC-20061 027-0003 v2.0 Firewall Commands 361 firewall level list List all the security levels. SYNT AX: where: RELA TED COMMANDS: firewall level list [format = <{pretty | cli}>] [string = <string>] [beginstring = <string>] format Select the output format in which the se curity levels must be shown.
E-DOC-CTC- 20061027-0003 v2 .0 Firewall Commands 362 firewall level modify Configure a security level. SYNT AX: where: firewall level modify name = <string> [index = <number>] [readonly = .
E-DOC-CTC-20061 027-0003 v2.0 Firewall Commands 363 firewall level set Set the security level or display the curr ent security level. SYNT AX: where: firewall level set [name = <string>] name The name of the secu rity level to be set. Note If no security level is spec ified, the current security level will be sho wn.
E-DOC-CTC- 20061027-0003 v2 .0 Firewall Commands 364 firewall rule add Add a firewall rule. SYNT AX: where: RELA TED COMMANDS: firewall rule add chain = <chain name> [index = <number>] [na.
E-DOC-CTC-20061 027-0003 v2.0 Firewall Commands 365 firewall rule delete Delete a fi rewall rule . SYNT AX: where: RELA TED COMMANDS: firewall rule delete chain = <string> index = <number> chain The name of th e chain in which a rule m ust be deleted.
E-DOC-CTC- 20061027-0003 v2 .0 Firewall Commands 366 firewall rule flush Flush all firewall rules. SYNT AX: where: firewall rule flush [chain = <string>] chain The name of th e chain for which the rules must be flushed. Note If not specifi ed, the rules of all the chains wi ll be flushed.
E-DOC-CTC-20061 027-0003 v2.0 Firewall Commands 367 firewall rule list Show a list of the fi rewall rules in a chain. SYNT AX: where: firewall rule list [chain = <string>] [format = <{pretty | cli}>] [string = <string>] [beginstring = <string>] chain The name of the chain for which the rules must be listed.
E-DOC-CTC- 20061027-0003 v2 .0 Firewall Commands 368 EXAMPLE: =>firewall rule list Rules (flags: C=Constant, D=Dynamic, E=Enable, L=Log) ===== Chain Nr.
E-DOC-CTC-20061 027-0003 v2.0 Firewall Commands 369 firewall rule modify Modify a firewall rule. SYNT AX: where: RELA TED COMMANDS: firewall rule modify chain = <string> index = <number> [.
E-DOC-CTC- 20061027-0003 v2 .0 Firewall Commands 370 firewall rule debug clear Clear the firewall rule statistics. SYNT AX: where: firewall rule debug clear [chain = <string>] [index = <number>] chain The name of the chain whi ch contains the rule.
E-DOC-CTC-20061 027-0003 v2.0 Firewall Commands 371 EXAMPLE: RELA TED COMMANDS: =>firewall rule debug stats chain index packets bytes ---------------------------------------------------------------.
E-DOC-CTC- 20061027-0003 v2 .0 Firewall Commands 372 firewall rule debug stats Show the firewall rule statistics. SYNT AX: where: firewall rule debug stats [chain = <chain name>] [index = <number>] chain The name of the chain for wh ich the statistics must be shown.
E-DOC-CTC-20061 027-0003 v2.0 Firewall Commands 373 EXAMPLE: RELA TED COMMANDS: =>firewall rule debug stats chain index packets bytes ---------------------------------------------------------------.
E-DOC-CTC- 20061027-0003 v2 .0 Firewall Commands 374 firewall rule debug traceconfig Display or modify the ru le trace configuration. SYNT AX: where: EXAMPLE: firewall rule debug traceconfig [trace = <{disabled | enabled}>] trace Enable or disable rule traces.
E-DOC-CTC-20061 027-0003 v2.0 GRP Commands 375 17 GRP Commands Introduction This chapter describes the commands of the grp comman d group. Contents This chapter covers th e following commands: grp config Set the Generic Routing Proto col (GRP) configuratio n settings.
E-DOC-CTC- 20061027-0003 v2 .0 GRP Commands 376 grp config Set the Generic Rout ing Protocol (GRP) c onfiguration settings . SYNT AX: where: EXAMPLE: grp config [cdistance = <number{0-255}>] [kdistance = <number{0-255}>] [rdistance = <number{0-255}>] [trace = <{disabled | enabled}>] cdistance A number between 0 and 255 .
E-DOC-CTC-20061 027-0003 v2.0 GRP Commands 377 grp flush Flush the GRP interface setti ngs and parameters. SYNT AX: grp flush.
E-DOC-CTC- 20061027-0003 v2 .0 GRP Commands 378 grp rtlist Show the current routes in th e GRP interfaces routing table. SYNT AX: where: EXAMPLE: grp rtlist [dst = <ip-address>] [dstmask = <ip-mask (dotted or cidr)>] dst The destination IP address of the route.
E-DOC-CTC-20061 027-0003 v2.0 GRP Commands 379 grp rip config Configure the RIP settings. SYNT AX: where: grp rip config state = <{disabled | enabled}> [version = <{rip_unspec | rip_v1 | rip_.
E-DOC-CTC- 20061027-0003 v2 .0 GRP Commands 380 impsrt Enable or disable the import of static routes. The defaul t is enabled . OP TIONAL impdefkrt Enable o r disable the i mport of the default kerne l route. The defaul t is enabled . OP TIONAL impdefsrt Enable or disable the import of the default static route.
E-DOC-CTC-20061 027-0003 v2.0 GRP Commands 381 EXAMPLE: RELA TED COMMANDS: =>grp rip show RIP routing protocol config dump ------------------------------------ RIP daemon is enabled Global RIP quer.
E-DOC-CTC- 20061027-0003 v2 .0 GRP Commands 382 grp rip flush Flush the RIP inter face settings and global parameters. SYNT AX: grp rip flush.
E-DOC-CTC-20061 027-0003 v2.0 GRP Commands 383 grp rip ifconfig Configure a RIP interface. SYNT AX: where: grp rip ifconfig intf = <string> [rip = <{disabled | enabled}>] [rxversion = <.
E-DOC-CTC- 20061027-0003 v2 .0 GRP Commands 384 EXAMPLE: =>grp rip ifconfig intf = myPPP_ppp [rip] = disabled [rxversion] = rip_unspec [authmode] = none [authstr] = [passive] = disabled [splithoriz.
E-DOC-CTC-20061 027-0003 v2.0 GRP Commands 385 grp rip show Show the RIP settings and the routes in the RIP database. SYNT AX: EXAMPLE: grp rip show =>grp rip show RIP routing protocol config dump .
E-DOC-CTC- 20061027-0003 v2 .0 GRP Commands 386.
E-DOC-CTC-20061 027-0003 v2.0 Hostmgr Commands 387 18 Hostmgr Commands Introduction This chapter describes the commands of the hostmg r command group. Contents This chapter covers th e following commands: hostmgr add Add host device info to the host manager .
E-DOC-CTC- 20061027-0003 v2 .0 Hostmgr Commands 388 hostmgr add Add host device info to the host manage r . SYNT AX: where: hostmgr add mac_addr = <hardware- address> [ip_addr = <ip-address&g.
E-DOC-CTC-20061 027-0003 v2.0 Hostmgr Commands 389 EXAMPLE: RELA TED COMMANDS: =>hostmgr list MAC-address IP-address Flags Type Intf Hw Intf Hostname ----------- ---------- ----- ---- ---- ------- -------- 00:10:a4:ad:32:cf 192.
E-DOC-CTC- 20061027-0003 v2 .0 Hostmgr Commands 390 hostmgr clear Remove all the hosts from the list. SYNT AX: EXAMPLE: RELA TED COMMANDS: hostmgr clear =>hostmgr list MAC-address IP-address Flags Type Intf Hw Intf Hostname ----------- ---------- ----- ---- ---- ------- -------- 00:10:a4:33:56:53 0.
E-DOC-CTC-20061 027-0003 v2.0 Hostmgr Commands 391 hostmgr config Configure the host m anager parameters. SYNT AX: where: EXAMPLE: hostmgr config [state = <{disabled | enabled}>] [scantime = <number{10-600}>] [autosave = <{disabled | enabled}>] [trace = <{disabled | enabled}>] state Enable or disable the host manager daemon.
E-DOC-CTC- 20061027-0003 v2 .0 Hostmgr Commands 392 hostmgr delete Delete the host device info from the host manager . SYNT AX: where: EXAMPLE: RELA TED COMMANDS: hostmgr delete mac_addr = <hardware-address> mac_addr The MAC address of the host to be rem oved.
E-DOC-CTC-20061 027-0003 v2.0 Hostmgr Commands 393 hostmgr flush Flush the ho st manager configuration. The host manager configu ration is cleaned and returne d to default values.
E-DOC-CTC- 20061027-0003 v2 .0 Hostmgr Commands 394 hostmgr list List all the host devices. SYNT AX: EXAMPLE: RELA TED COMMANDS: hostmgr list =>hostmgr list MAC-address IP-address Flags Type Intf Hw Intf Hostname ----------- ---------- ----- ---- ---- ------- -------- 00:10:a4:33:56:53 0.
E-DOC-CTC-20061 027-0003 v2.0 IDS Commands 395 19 IDS Commands Introduction This chapter describ es the comma nds of the ids command group. Contents This chapter covers the fo llowing commands: ids clear Reset the IDS statistics. 396 ids config Display/modify th e Intrusion Detection System (IDS) configuration.
E-DOC-CTC- 20061027-0003 v2 .0 IDS Commands 396 ids clear Reset the IDS statistics. SYNT AX: RELA TED COMMANDS: ids clear ids parser list Display the IDS parse r configurat ion.
E-DOC-CTC-20061 027-0003 v2.0 IDS Commands 397 ids config Display/modify the I ntrusion Detection System (IDS) configuratio n. SYNT AX: where: EXAMPLE: ids config [state = <{disabled | enabled}>] [trace = <{disabled|enabled}>] state Enable or disable IDS checks.
E-DOC-CTC- 20061027-0003 v2 .0 IDS Commands 398 ids parser list Display the IDS parse r configuration. SYNT AX: where: EXAMPLE: ids parser list [parser = <parser>] parser The na me of the parser.
E-DOC-CTC-20061 027-0003 v2.0 IDS Commands 399 ids parser modify Modify the IDS parser configuratio n. SYNT AX: where: ids parser modify parser = <string> state = <{disabled | enabled}> parser The na me of the IDS parser of which the configu ration must be modifi ed.
E-DOC-CTC- 20061027-0003 v2 .0 IDS Commands 400 EXAMPLE: =>ids list Resources: ========== resource total maximum --------------------------------- parsers 5 10 signatures 38 50 Signatures: ========.
E-DOC-CTC-20061 027-0003 v2.0 IDS Commands 401 ids pattern clear Reset the pattern tracker . SYNT AX: EXAMPLE: RELA TED COMMANDS: ids pattern clear =>ids pattern stats Pattern tracker statistics: -.
E-DOC-CTC- 20061027-0003 v2 .0 IDS Commands 402 ids pattern list Display the patterns in the pattern tracker . SYNT AX: where: EXAMPLE: RELA TED COMMANDS: ids pattern list [size = <{10 | 100 | full} or number>] size Th e size of the IDS pattern li st that will be shown.
E-DOC-CTC-20061 027-0003 v2.0 IDS Commands 403 ids pattern stats Display the p attern tracker s tatistics. SYNT AX: EXAMPLE: RELA TED COMMANDS: ids pattern stats =>ids pattern stats Pattern tracker.
E-DOC-CTC- 20061027-0003 v2 .0 IDS Commands 404 ids signature list Displays the ids sign ature configuration SYNT AX where EXAMPLE: ids signature list [signature = <fragment_sweep|zero- length_frag.
E-DOC-CTC-20061 027-0003 v2.0 IDS Commands 405 ids signature modify Modify the states of the signatures. SYNT AX where EXAMPLE: ids signature modify [signature = <fragment_sweep| zero-length_fragme.
E-DOC-CTC- 20061027-0003 v2 .0 IDS Commands 406 ids threshold clear Reset the IDS thresho lds to their default value s. SYNT AX: EXAMPLE: RELA TED COMMANDS: ids threshold clear =>ids threshold list index name window limit scaling ----------------------------------------------------------------- 1.
E-DOC-CTC-20061 027-0003 v2.0 IDS Commands 407 ids threshold list Display the IDS thresholds. SYNT AX: EXAMPLE: RELA TED COMMANDS: ids threshold list =>ids threshold list index name window limit scaling ----------------------------------------------------------------- 1.
E-DOC-CTC- 20061027-0003 v2 .0 IDS Commands 408 ids threshold modify Modify the IDS thresholds. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: ids threshold modify index = <number> [window = <number>] [limit = <number>] [scaling = <{disabled | enabled}>] index The index o f the IDS threshold to be modified .
E-DOC-CTC-20061 027-0003 v2.0 IGMP Commands 409 20 IGMP Commands Introduction This chapter describes the commands of the IGMP command group. Contents This chapter covers th e following commands: igmp host con fig Display or modify global IGMP co nfiguration.
E-DOC-CTC- 20061027-0003 v2 .0 IGMP Commands 410 igmp host config Display or modify gl obal IGMP configurati on. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: igmp host config [requirera = <{disabled | enabled}>] requirera E nable or d isable the ro uter alert IP o ption check.
E-DOC-CTC-20061 027-0003 v2.0 IGMP Commands 411 igmp host flush Flush the IGMP settings. SYNT AX: igmp host flush.
E-DOC-CTC- 20061027-0003 v2 .0 IGMP Commands 412 igmp host list Show the IGMP groups. SYNT AX: where: EXAMPLE: igmp host list [intf = <string>] [expand = <{disabled | enabled}>] intf The IP interface name. OP TIONAL expand Enable or disable expanded listing of IGMP grou ps.
E-DOC-CTC-20061 027-0003 v2.0 IGMP Commands 413 igmp host ifconfig Configure an IG MP interface. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: igmp host ifconfig intf = <string> version = <{none |IGMPv1 |IGMPv2 |IGMPv3}> intf The IP interface name.
E-DOC-CTC- 20061027-0003 v2 .0 IGMP Commands 414 igmp host iflist Show the configuration of the IGMP interfaces. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: igmp host iflist [expand = <{disabled | enabled}>] expand Enable or disable expanded listing of IGMP i nterfaces configuration.
E-DOC-CTC-20061 027-0003 v2.0 IGMP Commands 415 igmp host debug clear Clear IGMP statistics. SYNT AX: RELA TED COMMANDS: igmp host debug clear igmp host debu g stats Print IGMP statistics.
E-DOC-CTC- 20061027-0003 v2 .0 IGMP Commands 416 igmp host debug stats Print IGMP stati stics. SYNT AX: EXAMPLE: RELA TED COMMANDS: igmp host debug stats =>igmp host debug stats Total IGMP messages.
E-DOC-CTC-20061 027-0003 v2.0 IGMP Commands 417 igmp proxy config Configure the IGMP proxy . SYNT AX: where: igmp proxy config [state = <{disabled | enabled}>] [qi = <number{1-86400}>] [qr.
E-DOC-CTC- 20061027-0003 v2 .0 IGMP Commands 418 EXAMPLE: RELA TED COMMANDS: =>igmp proxy config IGMP proxy state : disabled Query Interval : 0 days, 0:02:05 Query Response Interval : 0 days, 0:00:.
E-DOC-CTC-20061 027-0003 v2.0 IGMP Commands 419 igmp proxy flush Flush all IGM P proxy settings and learned groups. SYNT AX: igmp proxy flush.
E-DOC-CTC- 20061027-0003 v2 .0 IGMP Commands 420 igmp proxy grouplist Show the learned group s on an IGMP proxy interface. SYNT AX: where: RELA TED COMMANDS: igmp proxy grouplist [intf = <string>] [expand = <{disabled | enabled}>] intf The name of the IGMP proxy in terface to be listed.
E-DOC-CTC-20061 027-0003 v2.0 IGMP Commands 421 igmp proxy ifconfig Configure an IGMP proxy interface. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: igmp proxy ifconfig intf = <string> [state = &l.
E-DOC-CTC- 20061027-0003 v2 .0 IGMP Commands 422 igmp proxy iflist Show the configuration of an IGMP proxy interface. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: igmp proxy iflist [expand = <{disabled | enabled}>] expand Enable or disable expanded listing of IGMP proxy interf ace configuration.
E-DOC-CTC-20061 027-0003 v2.0 IGMP Commands 423 igmp proxy mbslist Show the IGMP proxy mem bership database (merge of all l earned groups. SYNT AX: igmp proxy mbslist.
E-DOC-CTC- 20061027-0003 v2 .0 IGMP Commands 424 igmp proxy debug clear Clear IGMP proxy statistics. SYNT AX: RELA TED COMMANDS: igmp proxy debug clear igmp proxy debug stats Print IGMP proxy statis tics. igmp proxy debug traceco nfig Modify IG MP proxy trace configuratio n.
E-DOC-CTC-20061 027-0003 v2.0 IGMP Commands 425 igmp proxy debug stats Print IGMP proxy statistics. SYNT AX: EXAMPLE: RELA TED COMMANDS: igmp proxy debug stats =>igmp proxy debug stats IGMP proxy s.
E-DOC-CTC- 20061027-0003 v2 .0 IGMP Commands 426 igmp proxy debug traceconfig Modify IGMP pro xy trace configuration. SYNT AX: where: RELA TED COMMANDS: igmp proxy debug traceconfig [state = <{disabled | enabled}>] state Enable or disable tr acing.
E-DOC-CTC-20061 027-0003 v2.0 Interface Commands 427 21 Interface Commands Introduction This chapter describes the commands of the interf ace command group.
E-DOC-CTC- 20061027-0003 v2 .0 Interface Commands 428 interface list Display interfaces. SYNT AX: where: interface list [expand = <{disabled | enabled}>] [reverse = <{disabled | enabled}>] expand Enable or di sable expanded listing of interfaces.
E-DOC-CTC-20061 027-0003 v2.0 Interface Commands 429 EXAMPLE: =>interface list Name Type State Use UL Interfaces ethif1 physical connected 1 bridge ethif4 physical connected 1 bridge usbif1 physica.
E-DOC-CTC- 20061027-0003 v2 .0 Interface Commands 430.
E-DOC-CTC-20061 027-0003 v2.0 IP Commands 431 22 IP Commands Introduction This chapter describes the commands of the ip command group. Contents This chapter covers th e following commands: ip arpadd Add an entry to the ARP cache of a broadcast Internet Protocol (IP) interface.
E-DOC-CTC- 20061027-0003 v2 .0 IP Commands 432 ip debug sendto Sen d UDP packets. 468 ip debug stats Display IP statistics. 470 ip debug traceconfig Display/modify the IP st ack trace configuration.
E-DOC-CTC-20061 027-0003 v2.0 IP Commands 433 ip arpadd Add an entry to the ARP cache of a broa dcast Internet Protocol (IP) interface. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: ip arpadd intf = <string> ip = <ip-range> [hwaddr = <hardware-address>] intf The IP interface name.
E-DOC-CTC- 20061027-0003 v2 .0 IP Commands 434 ip arpdelete Delete an entry from the ARP cache. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: ip arpdelete intf = <string> ip = <ip-range> [hwaddr = <hardware-address>] intf The IP interface name.
E-DOC-CTC-20061 027-0003 v2.0 IP Commands 435 ip arplist Display the ARP cache. SYNT AX: EXAMPLE: RELA TED COMMANDS: ip arplist =>ip arplist Interface IP-address HW-address Type 2 eth0 10.0.0.1 00:10:a4:ad:32:cf STATIC 2 eth0 10.0.0.2 00:00:00:00:00:00 DYNAMIC 2 eth0 10.
E-DOC-CTC- 20061027-0003 v2 .0 IP Commands 436 ip config Show/set global IP stack configura tion options. SYNT AX: where: ip config [forwarding = <{disabled | enabled}>] [redirects = <{disabl.
E-DOC-CTC-20061 027-0003 v2.0 IP Commands 437 EXAMPLE: addrcheck Set the level of IP address checks. Choose between: > of f : No address ch ecking is performed. For advanced users on ly; in normal circumstances there sh ould always be some kind of address checking.
E-DOC-CTC- 20061027-0003 v2 .0 IP Commands 438 ip flush Flush all the static IP par ameters. Dynamic configuration s (for example from PPP or CIP links) rema in. SYNT AX: i The flush command do es not impact previously save d configuration s. ! The command :ip flush deletes all local IP conn ectivity .
E-DOC-CTC-20061 027-0003 v2.0 IP Commands 439 ip ifadd Create an IP interface. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: ip ifadd intf = <string> dest = <string> intf The name of the IP i nte rface to be created . REQUIRED dest An network interface name.
E-DOC-CTC- 20061027-0003 v2 .0 IP Commands 440 ip ifattach Attach an IP in terface. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: ip ifattach intf = <string> intf The name of the IP i nte rface to be attached.
E-DOC-CTC-20061 027-0003 v2.0 IP Commands 441 ip ifconfig Configure the parameters of an IP interface. SYNT AX: where: ip ifconfig intf = <string> [mtu = <number{68-65535}>] [status = <.
E-DOC-CTC- 20061027-0003 v2 .0 IP Commands 442 EXAMPLE: =>ip iflist Interface Group MTU RX TX TX-Drop Status HW-address 0 loop local 65535 123966 75177 0 [UP] 00:0e:50:0f:fc:2c 1 Internet wan 1500 .
E-DOC-CTC-20061 027-0003 v2.0 IP Commands 443 ip ifdelete Delete an IP interface. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: ip ifdelete intf = <string> intf The name of the IP i nte rface to be deleted.
E-DOC-CTC- 20061027-0003 v2 .0 IP Commands 444 ip ifdetach Detach an IP interface. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: ip ifdetach intf = <string> intf The name of the IP i nte rface to be detached .
E-DOC-CTC-20061 027-0003 v2.0 IP Commands 445 ip iflist Display all the IP interfaces. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: ip iflist [expand = <{disabled | enabled}>] [string = <string>] [beginstring = <string>] expand Enable or disa ble expanded listing.
E-DOC-CTC- 20061027-0003 v2 .0 IP Commands 446 ip ifwait W ait for a status change of an IP interface. SYNT AX: where: RELA TED COMMANDS: ip ifwait intf = <string> [timeout = <number{1-600000}>] [adminstatus = <{down | up}>] [operstatus = <{down | up}>] [linkstatus = <{down | up}>] intf The IP i nterface name.
E-DOC-CTC-20061 027-0003 v2.0 IP Commands 447 ip ipadd Assign an IP add ress to an IP interface. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: ip ipadd intf = <string> addr = <ip-address> [netmask = <ip-mask(dotted or cidr)>] [pointopoint = <ip-address>] [addroute = <{disabled | enabled}>] intf The IP interface name.
E-DOC-CTC- 20061027-0003 v2 .0 IP Commands 448 ip ipconfig Modify an IP ad dress configuration. SYNT AX: where: EXAMPLE: ip ipconfig addr = <ip-address> [preferred = <{disabled | enabled}>] [primary = <{disabled | enabled}>] addr The IP address t o be configured.
E-DOC-CTC-20061 027-0003 v2.0 IP Commands 449 ip ipdelete Remove an IP address fr om an IP interface. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: ip ipdelete addr = <ip-address> addr The IP address to b e deleted. REQ UIRED =>ip iplist Interface Type IP-address Point-to-point/Mask 1 eth0 Ethernet 10.
E-DOC-CTC- 20061027-0003 v2 .0 IP Commands 450 ip iplist Display all the configured IP addresses. SYNT AX: EXAMPLE: RELA TED COMMANDS: ip iplist =>ip iplist Interface Type IP-address Point-to-point/Mask 2 LocalNetwork Ethernet 10.0.0.138 255.255.255.
E-DOC-CTC-20061 027-0003 v2.0 IP Commands 451 ip mcast rtadd Add a multi cast route to the multic ast routing table. SYNT AX: where: RELA TED COMMANDS: ip mcast rtadd srcintf = <string> [src = &.
E-DOC-CTC- 20061027-0003 v2 .0 IP Commands 452 ip mcast rtdelete Delete a multicast route from the multic ast routing table. SYNT AX: where: RELA TED COMMANDS: ip mcast rtdelete srcintf = <string> [src = <ip-address>] grp = <ip-address> dstintf = <string> srcintf The source IP interface.
E-DOC-CTC-20061 027-0003 v2.0 IP Commands 453 ip mcast rtlist Display the multic ast routing table. SYNT AX: where: RELA TED COMMANDS: ip mcast rtlist [expand = <{disabled | enabled}>}] expand Enable or disable expanded listin g. The default is disabled .
E-DOC-CTC- 20061027-0003 v2 .0 IP Commands 454 ip mcast flush Flush the multicast rout ing table. SYNT AX: RELA TED COMMANDS: ip mcast flush ip mcast rtadd Add a multicast route to the multicast routing table. ip mcast rtdelete Delete a multicast route from the multicast routing table.
E-DOC-CTC-20061 027-0003 v2.0 IP Commands 455 ip rtadd Add a route to the routing table. SYNT AX: where: ip rtadd dst = <ip-address> [dstmsk = <ip-mask(dotted or cidr)>] [label = <strin.
E-DOC-CTC- 20061027-0003 v2 .0 IP Commands 456 EXAMPLE: RELA TED COMMANDS: =>ip rtlist Destination Label Gateway Intf Mtrc Status 10.0.0.0/24 10.0.0.140 eth0 0 [UP] 10.0.0.140/32 10.0.0.140 eth0 0 [UP] 127.0.0.1/32 127.0.0.1 loop 0 [UP] =>ip rtadd dst=10.
E-DOC-CTC-20061 027-0003 v2.0 IP Commands 457 ip rtdelete Delete a route from the routing table. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: ip rtdelete dst = <ip-address> [dstmsk = <ip-mask(.
E-DOC-CTC- 20061027-0003 v2 .0 IP Commands 458 ip rtlist Display the routing table. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: ip rtlist [expand = <{disabled | enabled}>] expand Enable or disable expanded listin g. The default is disabled . OP TIONAL =>ip rtlist Destination Label Gateway Interface Metric Status 10.
E-DOC-CTC-20061 027-0003 v2.0 IP Commands 459 ip auto flush Flush the auto IP interfaces. SYNT AX: ip auto flush.
E-DOC-CTC- 20061027-0003 v2 .0 IP Commands 460 ip auto ifadd Create an autoIP interface. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: ip auto ifadd intf = <string> [addr = <ip-address>] intf T he name of the IP interface for which a link-local ad dress has to be allocated.
E-DOC-CTC-20061 027-0003 v2.0 IP Commands 461 ip auto ifattach Select and assign a link-local ad dress to an autoIP interface. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: ip auto ifattach intf = <string> intf The name of the autoIP in terface for which a link-local address has to be attached.
E-DOC-CTC- 20061027-0003 v2 .0 IP Commands 462 ip auto ifconfig Configure an autoIP interface. SYNT AX: where: ip auto ifconfig intf = <string> [addr = <ip-address>] [poolstart = <ip-ad.
E-DOC-CTC-20061 027-0003 v2.0 IP Commands 463 EXAMPLE: => ip auto iflist eth0 : [INIT] 0.0.0.0 poolstart = 169.254.1.1 poolend = 169.254.254.254 netmask = 255.255.0.0 claim : 10 defence : 5 probe : 4 interval : 2 (sec) probes sent = 0 collisions = 0 =>ip auto ifconfig intf=ipsec0 claim=5 probe=5 => ip auto iflist ipsec0 : [INIT] 0.
E-DOC-CTC- 20061027-0003 v2 .0 IP Commands 464 ip auto ifdelete Delete an existing autoIP interface. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: ip auto ifdelete intf = <string> intf The name of the IP i nte rface to be deleted. REQUIRED =>ip auto iflist ipsec0 : [SELECTING] 169.
E-DOC-CTC-20061 027-0003 v2.0 IP Commands 465 ip auto ifdetach Release the link-local address for the given autoIP interface. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: ip auto ifdetach intf = <string> intf The name of the autoIP in terface for which a link-local address has to be detached.
E-DOC-CTC- 20061027-0003 v2 .0 IP Commands 466 ip auto iflist Display the autoIP interfaces. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: ip auto iflist [intf = <string>] intf The name of the autoIP interface to be listed. Note If not specified, all the au toIP interfaces are shown.
E-DOC-CTC-20061 027-0003 v2.0 IP Commands 467 ip debug httpprobe Send a HTTP probe. This HTTP probe will meas ure the Round T rip T ime (RTT) taken to connect and access data from a HTTP server .
E-DOC-CTC- 20061027-0003 v2 .0 IP Commands 468 ip debug sendto Send UDP packets. SYNT AX: where: ip debug sendto addr = <ip-address> [count = <number{1-1000000}>] [size = <number{0-2000.
E-DOC-CTC-20061 027-0003 v2.0 IP Commands 469 EXAMPLE: =>ip debug sendto addr=10.0.0.148 listen=on srcport=19 dstport=1025 =>ip debug sendto addr=10.0.0.148 listen=on srcport=19 dstport=1025 1 bytes from 10.0.0.148:1025 41 A =>ip debug sendto addr=10.
E-DOC-CTC- 20061027-0003 v2 .0 IP Commands 470 ip debug stats Display IP statistics. SYNT AX: EXAMPLE: ip debug stats =>ip debug stats Total datagrams received : 8599 IP header errors : 0 Datagrams.
E-DOC-CTC-20061 027-0003 v2.0 IP Commands 471 ip debug traceconfig Display/mod ify the IP st ack trace configura tion. SYNT AX: where: ip debug traceconfig [input = <{none | label | -telnet | -host.
E-DOC-CTC- 20061027-0003 v2 .0 IP Commands 472 EXAMPLE: EXAMPLE: =>ip debug traceconfig Input traces : none Forward traces : none Output traces : none Drop traces : all Path traces : none Trace mode : line ARP traces : none => =>ip debug traceroute addr = 192.
E-DOC-CTC-20061 027-0003 v2.0 IPQoS Commands 473 23 IPQoS Commands Introduction This chapter describes the commands of the ipqos comman d group. Contents This chapter covers th e following commands: ipqos config Configure IPQoS for a given dest ination interface for the IPQoS queues instantiation.
E-DOC-CTC- 20061027-0003 v2 .0 IPQoS Commands 474 ipqos config Configure IPQoS for a given destination interface for the IPQoS qu eues instantiation . SYNT AX: where: i When enabling or disa bling IPQoS, ta ke the following into account: > if the W A N interface (for example PPPoA, IP oA,.
E-DOC-CTC-20061 027-0003 v2.0 IPQoS Commands 475 priority Select the subq ueue priority algorithm. Choose betwee n: > wfq : W eighted Fair Q ueuing (WFQ) is used for th e four AF queues. The realtime queu e has priority over the WFQ queues, which have priority over the best-effort queue.
E-DOC-CTC- 20061027-0003 v2 .0 IPQoS Commands 476 EXAMPLE: RELA TED COMMANDS: =>ipqos config dest=atm_pvc_8_35 state=enabled =>ipqos list Name State Discard Priority Size Size Rate Burst Weights.
E-DOC-CTC-20061 027-0003 v2.0 IPQoS Commands 477 ipqos list Display the IPQoS con figuration. SYNT AX: EXAMPLE: RELA TED COMMANDS: ipqos list =>ipqos list Name State Discard Priority Size Size Rate.
E-DOC-CTC- 20061027-0003 v2 .0 IPQoS Commands 478 ipqos ef config Configure the IPQoS Expedited Forwar ding (EF) timer for an interface. SYNT AX: where: EXAMPLE: The example below shows the de fault c.
E-DOC-CTC-20061 027-0003 v2.0 IPQoS Commands 479 ipqos ef list Display the IPQoS EF timers. SYNT AX: EXAMPLE: RELA TED COMMANDS: ipqos ef list =>ipqos ef list Interface State Timeout MTU (ms) (byte.
E-DOC-CTC- 20061027-0003 v2 .0 IPQoS Commands 480 ipqos ef stats Display the IPQoS EF timer statistics. SYNT AX: EXAMPLE: RELA TED COMMANDS: ipqos ef stats =>ipqos ef stats Interface State Remain (ms) loop active 900 Rt_PPPoA2 active 900 eth0 disabled 0 => ipqos ef config Configure the IPQoS Expedited Forwardi ng (EF) timer for an interface.
E-DOC-CTC-20061 027-0003 v2.0 IPQoS Commands 481 ipqos queue clear Clear the IPQoS statistics. SYNT AX: EXAMPLE: RELA TED COMMANDS: ipqos queue clear =>ipqos queue stats Name Queue # packets # pack.
E-DOC-CTC- 20061027-0003 v2 .0 IPQoS Commands 482 ipqos queue config Modify the IPQoS subqueue configuration. SYNT AX: where: ipqos queue config dest = <string> queue = <number{0-5}> [prop.
E-DOC-CTC-20061 027-0003 v2.0 IPQoS Commands 483 EXAMPLE: RELA TED COMMANDS: maxbytes A number between 0 and 128. Represents the maxim um size in kilobytes of this q ueue. The default is 0 for the Real time que ue and 20 for the other queues. Note 0 means that a maximum size is not enforced.
E-DOC-CTC- 20061027-0003 v2 .0 IPQoS Commands 484 ipqos queue list Display the IPQoS subq ueue configuration. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: ipqos queue list [dest = <string}>] dest The destination interface for the IPQoS queues instantiation.
E-DOC-CTC-20061 027-0003 v2.0 IPQoS Commands 485 ipqos queue stats Show the IPQoS subq ueue statistics. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: ipqos queue stats [dest = <string}>] dest The destination interface for the IPQoS queues instantiation.
E-DOC-CTC- 20061027-0003 v2 .0 IPQoS Commands 486.
E-DOC-CTC-20061 027-0003 v2.0 Label Commands 487 24 Label Commands Introduction This chapter describes the commands of the label comman d group. Contents This chapter covers th e following commands: label add Create a new label. 488 label delete Del ete a label.
E-DOC-CTC- 20061027-0003 v2 .0 Label Commands 488 label add Create a new label. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: label add name = <string> name The name of the labe l to be ad ded.
E-DOC-CTC-20061 027-0003 v2.0 Label Commands 489 label delete Delete a label. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: label delete name = <string> [force = <{disabled | enabled}>] name The name of the label to be deleted.
E-DOC-CTC- 20061027-0003 v2 .0 Label Commands 490 label flush Flush all labels. SYNT AX: i The flush command do es not impact previously saved configurations.
E-DOC-CTC-20061 027-0003 v2.0 Label Commands 491 label list Display the labels. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: label list [name = <string>] name The name of the label to be displayed . Note If not specified, all the labels will be displayed.
E-DOC-CTC- 20061027-0003 v2 .0 Label Commands 492 label modify Modify a label configuratio n. SYNT AX: where: label modify name = <string> [classification = <{ignore | overwrite | increase}&g.
E-DOC-CTC-20061 027-0003 v2.0 Label Commands 493 ackclass The priority cla ss of the ACK segments of the TCP connection. Choose between: > A number between 0 an d 15 > prioritize > defclass.
E-DOC-CTC- 20061027-0003 v2 .0 Label Commands 494 EXAMPLE: =>label list Name Class Def Ack Bidirect Inherit Tos mark Type Value Use Trace DSCP overwrite dscp defclass disabled disabled disabled tos.
E-DOC-CTC-20061 027-0003 v2.0 Label Commands 495 label chain add Add a new label chain. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: label chain add chain = <string> chain The nam e of the chain to be added.
E-DOC-CTC- 20061027-0003 v2 .0 Label Commands 496 label chain delete Delete a label chain. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: label chain delete chain = <string> chain The nam e of the chain to be deleted.
E-DOC-CTC-20061 027-0003 v2.0 Label Commands 497 label chain flush Flush all label chain s. SYNT AX: label chain flush.
E-DOC-CTC- 20061027-0003 v2 .0 Label Commands 498 label chain list Display a list of chains. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: label chain list [format = <{pretty | cli}>] format Select the output format of the list. Choose between: > pret ty : the configuration is show n as intuitive output in clear text.
E-DOC-CTC-20061 027-0003 v2.0 Label Commands 499 label rule add Add a label rule. SYNT AX: where: label rule add chain = <chain name> [index = <number>] [name = <string>] [clink = &l.
E-DOC-CTC- 20061027-0003 v2 .0 Label Commands 500 EXAMPLE: RELA TED COMMANDS: =>label rule list Rules (flags: C=Constant, D=Dynamic, E=Enabl e, L=Log) ===== Chain Nr.
E-DOC-CTC-20061 027-0003 v2.0 Label Commands 501 label rule list Display a list of label rules..
E-DOC-CTC- 20061027-0003 v2 .0 Label Commands 502 label rule delete Delete a label rule. SYNT AX: where: EXAMPLE: label rule delete chain = <string> index = <number> chain The nam e of the chain in whic h a rule must be deleted. REQUIRED index The index number of the rule in the chain.
E-DOC-CTC-20061 027-0003 v2.0 Label Commands 503 RELA TED COMMANDS: label rule add Add a label rule. label rule list Display a list of label rules..
E-DOC-CTC- 20061027-0003 v2 .0 Label Commands 504 label rule flush Flush all label rules. The chains themselves are not removed. SYNT AX: where: i The flush command do es not impact previously saved configurations. label rule flush [chain = <string>] chain The nam e of the chain to be flushed.
E-DOC-CTC-20061 027-0003 v2.0 Label Commands 505 label rule list Display a list of label rules. SYNT AX: where: label rule list [chain = <string>] [format = <{pretty | cli}>] [string = <string>] [beginstring = <string>] chain The name of the chain for which the rules must be listed.
E-DOC-CTC- 20061027-0003 v2 .0 Label Commands 506 EXAMPLE: RELA TED COMMANDS: =>label rule list format=cli :label rule add chain=qos_default_labels index=1 serv=sip log=disabled state=enabled label.
E-DOC-CTC-20061 027-0003 v2.0 Label Commands 507 label rule modify Modify a label rule. SYNT AX: where: label rule modify chain = <chain name> index = <number> [newindex = <number>] .
E-DOC-CTC- 20061027-0003 v2 .0 Label Commands 508 label rule debug clear Clear the label rule statistics. SYNT AX: where: label rule debug clea r [chain = <string>] [index = <number>] chain The name of the chain in which the rule is to be found.
E-DOC-CTC-20061 027-0003 v2.0 Label Commands 509 EXAMPLE: RELA TED COMMANDS: =>label rule debug stats chain=qos_labels chain index packets bytes ----------------------------------------------------.
E-DOC-CTC- 20061027-0003 v2 .0 Label Commands 510 label rule debug stats Display the label ru le statistics. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: label rule debug stat s [chain = <string>] [index = <number>] chain The nam e of the chain for wh ich the statistics must be shown.
E-DOC-CTC-20061 027-0003 v2.0 Label Commands 511 label rule debug traceconfig Display or modify the ru le trace configuration. SYNT AX: where: EXAMPLE: label rule debug trac econfig [trace = <{disabled | enabled}>] trace Disable or enable rule traces.
E-DOC-CTC- 20061027-0003 v2 .0 Label Commands 512.
E-DOC-CTC-20061 027-0003 v2.0 Language Commands 513 25 Language Commands Introduction This chapter describes the commands of the langua ge command grou p. Contents This chapter covers th e following commands: language config Select a language. 514 language delete Delete one or all language archives.
E-DOC-CTC- 20061027-0003 v2 .0 Language Commands 514 language config Select a langua ge. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: language config [language = <string>] [complete = <{yes | no}>] language Langu age code: OSI langua ge code (2 chars) for language.
E-DOC-CTC-20061 027-0003 v2.0 Language Commands 515 language delete Delete one or all language arch ives. SYNT AX: where: RELA TED COMMANDS: language delete [file = <string>] [all = <{yes | no}>] file The filename of the lang uage archive to be removed.
Language Commands E-DOC-CTC- 20061027-0003 v2 .0 516 language list List the available language archives. SYNT AX: EXAMPLE: RELA TED COMMANDS: language list =>language list CODE LANGUAGE VERSION FILENAME en* English 5.3.0.10.0 <system> => i The currently sele cted language is indicate d by a “*” next to the OSI language code.
E-DOC-CTC-20061 027-0003 v2.0 MBUS Commands 517 26 MBUS Commands Introduction This chapter describes the commands of the mbus command group. Contents This chapter covers th e following commands: mbus client config Modify clie nt parameters. 518 mbus client exec Execute mbus command.
E-DOC-CTC- 20061027-0003 v2 .0 MBUS Commands 518 mbus client config Modify clie nt parameters. SYNT AX: where: RELA TED COMMANDS: mbus client config [writelock = <{enabled | disabled}>] [wlgetim.
E-DOC-CTC-20061 027-0003 v2.0 MBUS Commands 519 mbus client exec Execute mbus command. SYNT AX: where: mbus client exec cmd = <{addobject | deleteobject | getparamattr ibutes | getparamcount | getp.
E-DOC-CTC- 20061027-0003 v2 .0 MBUS Commands 520 RELA TED COMMANDS: mbus client config Modify client parameters. mbus client regi ster Register cli cl ie nt to mbus.
E-DOC-CTC-20061 027-0003 v2.0 MBUS Commands 521 mbus client register Register cli client to mbus. SYNT AX: RELA TED COMMANDS: mbus client register mbus client config Modify client parameters. mbus client exec Execute mbus co mmand. mbus debug stats Display mbus statistics.
E-DOC-CTC- 20061027-0003 v2 .0 MBUS Commands 522 mbus debug stats Display mbus statistics. SYNT AX: RELA TED COMMANDS: mbus debug stats mbus debug traceconfig Modify mbus trace settings.
E-DOC-CTC-20061 027-0003 v2.0 MBUS Commands 523 mbus debug clearstats Reset MBUS statistics . SYNT AX: RELA TED COMMANDS: mbus debug clearstats mbus debug stats Display mbus statistics.
E-DOC-CTC- 20061027-0003 v2 .0 MBUS Commands 524 mbus debug traceconfig Modify mbus trace settings. SYNT AX: where: RELA TED COMMANDS: mbus debug traceconfig [level = <number{0-4}>] level A number between 0 and 4. Represents the mbus trace level.
E-DOC-CTC-20061 027-0003 v2.0 MBUS Commands 525 mbus listobjects Display the object instances. SYNT AX: where: RELA TED COMMANDS: mbus listobjects [path = <quoted string>] [type = <{idpath | keypath}>] [output = <{list | tree}>] [expand = <{disabled | enabled}>] path Fully qualified m bus path to list.
E-DOC-CTC- 20061027-0003 v2 .0 MBUS Commands 526 mbus listtypes Display the registered objecttypes. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: mbus listtypes [path = <quoted string>] [expand = <{disabled | enabled}>] path Fully qualified m bus path to list.
E-DOC-CTC-20061 027-0003 v2.0 MBUS Commands 527 mbus listenums Display the registered enumtypes. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: mbus listenumss [dmtree = <{igd|atomic|system}>] [name = <quoted string>] [expand = <{disabled|enabled}>] dmtree Select mbusd da tamodel tree.
E-DOC-CTC- 20061027-0003 v2 .0 MBUS Commands 528 mbus listcontexts Display the context instances . SYNT AX: where: RELA TED COMMANDS: listcontexts [dmtree = <{igd|atomic|system}>] dmtree Select mbusd da tamodel tree. OPTIONAL mbus listobjects Display the object instances.
E-DOC-CTC-20061 027-0003 v2.0 MBUS Commands 529 mbus listsubscriptions Display the subscrip tion instances . SYNT AX: where: RELA TED COMMANDS: listsubscriptions [dmtree = <{igd|atomic|system}>] dmtree Select mbusd da tamodel tree. OPTIONAL mbus listobjects Display the object instances.
E-DOC-CTC- 20061027-0003 v2 .0 MBUS Commands 530 mbus debug loadobjects Load object instances of registered objecttypes. SYNT AX: where: RELA TED COMMANDS: mbus debug loadobjects [dmtree = <{igd|at.
E-DOC-CTC-20061 027-0003 v2.0 MBUS Commands 531 mbus debug unloadobjects Unload object inst ances. SYNT AX: where: RELA TED COMMANDS: mbus unloadobjects [path = <quoted string>] [type = <{idpath | keypath}>] path Fully qualified m bus path.
E-DOC-CTC- 20061027-0003 v2 .0 MBUS Commands 532 mbus pluginevent Simulate event from plugin . SYNT AX: where: mbus pluginevent ctxid = <number{0--2}> type = <{addobj|delobj|updobj}> path .
E-DOC-CTC-20061 027-0003 v2.0 MBUS Commands 533 mbus unregister Unregister a client/p lugin context . SYNT AX: where: unregister id = <number> id message-based client/plugin con text id.
E-DOC-CTC- 20061027-0003 v2 .0 MBUS Commands 534 mbus client unregister Unregister cli client from mbus . SYNT AX: unregister.
E-DOC-CTC-20061 027-0003 v2.0 MEMM Commands 535 27 MEMM Commands Introduction This chapter describes the commands of the memm command group. Contents This chapter covers th e following commands: memm debug lock traceconfig Modify lock trace settings. 536 memm debug traceconfig Modify memm trace settings.
E-DOC-CTC- 20061027-0003 v2 .0 MEMM Commands 536 memm debug lock traceconfig Modify lock trace settings. SYNT AX: where: memm debug lock traceconfig [level = <number{0-4}>] [name = <string>] level A number betwe en 0 and 4. Represents the memm trace level.
E-DOC-CTC-20061 027-0003 v2.0 MEMM Commands 537 memm debug traceconfig Modify memm trace settings. SYNT AX: where: memm debug traceconfig [level = <number{0-4}>] level A number betwe en 0 and 4.
E-DOC-CTC- 20061027-0003 v2 .0 MEMM Commands 538 memm debug clearstats Clear time statistics SYNT AX: memm debug clearstats.
E-DOC-CTC-20061 027-0003 v2.0 MEMM Commands 539 memm debug lock stats Display lock statistics SYNT AX: memm debug lock stats.
E-DOC-CTC- 20061027-0003 v2 .0 MEMM Commands 540 memm listobjects Display objects. SYNT AX: where: memm listobjects [name = <quoted string>] name Select typename(s) to list (s upports partial typename).
E-DOC-CTC-20061 027-0003 v2.0 MEMM Commands 541 memm stats Display memm statistics. SYNT AX: where: EXAMPLE: memm stats [name = <quoted string>] name Select typename(s) to list (s upports partial typename). OPTIONAL =>memm stats pool name bytes cur,max,avail (m ax.
E-DOC-CTC- 20061027-0003 v2 .0 MEMM Commands 542 EXAMPLE: =>memm stats pool name bytes cur,max,avail (max.%) count cur,max,avail ref cur,max,avail ------------- --------------------------- --------.
E-DOC-CTC-20061 027-0003 v2.0 MLP Commands 543 28 MLP Commands Introduction This chapter describes the commands of the mlp comman d group. Contents This chapter covers th e following commands: mlp flush Flush all the Multi-Level access Policies (MLP) structures.
E-DOC-CTC- 20061027-0003 v2 .0 MLP Commands 544 mlp flush Flush all the Multi-Level acce ss Policies (MLP) structures. SYNT AX: mlp flush.
E-DOC-CTC-20061 027-0003 v2.0 MLP Commands 545 mlp import Import all the scores. SYNT AX: where: RELA TED COMMANDS: mlp import [trace = <{disabled | enabled | full}>] trace Select the impo rt trace level. Choose between: > disabled > enabled > full.
E-DOC-CTC- 20061027-0003 v2 .0 MLP Commands 546 mlp debug export Export all the scores. SYNT AX: RELA TED COMMANDS: mlp debug export mlp import Import all the scores.
E-DOC-CTC-20061 027-0003 v2.0 MLP Commands 547 mlp debug stats Display MLP statistics. SYNT AX: EXAMPLE: mlp debug stats =>mlp debug stats Roles (cur/free/max) : 8/7/15 Privileges (cur/free/max) : .
E-DOC-CTC- 20061027-0003 v2 .0 MLP Commands 548 mlp debug traceconfig Modify the MLP trace settings. SYNT AX: where: EXAMPLE: mlp debug traceconfig [trace = <{disabled | enabled | full}>] trace Selec t the trace level. Choose between: > disabled > enabled > full.
E-DOC-CTC-20061 027-0003 v2.0 MLP Commands 549 mlp privilege add Add a privilege. SYNT AX: where: mlp privilege add name = <quoted string> type = <{access | service}> [descr = <quoted string>] name The name of the new privilege. Note The maximum number of privileges is 60.
E-DOC-CTC- 20061027-0003 v2 .0 MLP Commands 550 EXAMPLE: RELA TED COMMANDS: =>mlp privilege list type=access Privilege (type) Description ---------------------------- anyaccess (access) All access .
E-DOC-CTC-20061 027-0003 v2.0 MLP Commands 551 mlp privilege addzone Add a zone to a privilege. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: i Only one zone can b e added at a time to a priv ilege. If multiple zo nes need to be added, the command :mlp privileg e addzone must be executed for each zone to be added.
E-DOC-CTC- 20061027-0003 v2 .0 MLP Commands 552 mlp privilege config Modify a privilege. SYNT AX: where: EXAMPLE: mlp privilege config name = <string> [descr = <quoted string>] [score = <{hex-word}[:{hex-word}] ex: 'a12:c30f'>] name The name of the privilege to b e modified.
E-DOC-CTC-20061 027-0003 v2.0 MLP Commands 553 mlp privilege delete Delete a privilege. SYNT AX: where: EXAMPLE: mlp privilege delete name = <string> name The name of the privil ege to b e deleted.
E-DOC-CTC- 20061027-0003 v2 .0 MLP Commands 554 RELA TED COMMANDS: mlp privilege delete Add a privilege. mlp privilege list Display the privileges..
E-DOC-CTC-20061 027-0003 v2.0 MLP Commands 555 mlp privilege list Display the priv ileges. SYNT AX: where: mlp privilege list [name = <string>] [type = <{access | service}>] [verbose = <{minimal | medium | all}>] name The name of the privilege to b e listed.
E-DOC-CTC- 20061027-0003 v2 .0 MLP Commands 556 EXAMPLE: RELA TED COMMANDS: =>mlp privilege list type=service Privilege (type) Description ---------------------------- anyservice (service) All serv.
E-DOC-CTC-20061 027-0003 v2.0 MLP Commands 557 mlp privilege removezone Remove a zone from a privilege. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: i Only one zone can be removed at a time from a priv ilege. If multiple zones n eed to be removed, the command :mlp privileg e removezone must be executed for each zone to be removed.
E-DOC-CTC- 20061027-0003 v2 .0 MLP Commands 558 mlp role add Add a role. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: mlp role add name = <quoted string> parent = <string> [descr = <quoted string>] name The name of the new ro le. Note The maximum number of r oles is 15.
E-DOC-CTC-20061 027-0003 v2.0 MLP Commands 559 mlp role list Display the roles..
E-DOC-CTC- 20061027-0003 v2 .0 MLP Commands 560 mlp role addpriv Add a privilege to a role. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: mlp role addpriv name = <string> access = <string> service = <string> name The name of the role. REQUIRED access The nam e of the access privilege to be added.
E-DOC-CTC-20061 027-0003 v2.0 MLP Commands 561 mlp role config Modify the role. SYNT AX: where: EXAMPLE: mlp role config name = <string> [parent = <string>] [descr = <quoted string>] name The name of the role to be configured. REQUIRED parent The name of the parent role.
E-DOC-CTC- 20061027-0003 v2 .0 MLP Commands 562 mlp role delete Delete a role. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: mlp role delete name = <string> name The name of the role to be deleted.
E-DOC-CTC-20061 027-0003 v2.0 MLP Commands 563 mlp role list Display the roles. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: mlp role list [name = <string>] [verbose = <{minimal | medium | all}>] name The name of the role to be listed. Note If not specified, all the ro les will be listed.
E-DOC-CTC- 20061027-0003 v2 .0 MLP Commands 564 mlp role removepriv Remove a privilege from a role. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: mlp role removepriv name = <string> access = <string> [service = <string>] name The name of the role.
E-DOC-CTC-20061 027-0003 v2.0 NAT Commands 565 29 NA T Commands Introduction This chapter describes the commands of the nat comman d group. Contents This chapter covers th e following commands: nat config Display/modify gl obal NA T configuration op tions.
E-DOC-CTC- 20061027-0003 v2 .0 NAT Commands 566 nat config Display/modif y global NA T configuration optio ns. SYNT AX: where: EXAMPLE: nat config [trace = <{disabled | enabled}>] trace Enable or disable traces.
E-DOC-CTC-20061 027-0003 v2.0 NAT Commands 567 nat flush Flush the curren t NA T configuration. SYNT AX: nat flush.
E-DOC-CTC- 20061027-0003 v2 .0 NAT Commands 568 nat ifconfig Modify address translation on an IP interface. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: nat ifconfig intf = <string> translation = <{disabled | enabled | trans- parent}> intf The IP interface name.
E-DOC-CTC-20061 027-0003 v2.0 NAT Commands 569 nat iflist Display the address translation co nfiguration on all the interfaces. SYNT AX: EXAMPLE: RELA TED COMMANDS: nat iflist =>nat iflist Interface NAT loop disabled Internet enabled RtPPPoE_ppp enabled LocalNetwork transparent => nat ifconfig Modify address transla tio n on an IP interfac e.
E-DOC-CTC- 20061027-0003 v2 .0 NAT Commands 570 nat mapadd Add an address mapp ing to a Network Addr ess T ranslation (NA T) enabled interface. SYNT AX: where: nat mapadd intf = <string> [type =.
E-DOC-CTC-20061 027-0003 v2.0 NAT Commands 571 inside_addr The inside (typi cally pr ivate) IP address. > Inbound: Represents the address(es ) to be used as destination address after translation. > Outbound: Thi s map will only apply if the so urce IP address is part of the inside address(es).
E-DOC-CTC- 20061027-0003 v2 .0 NAT Commands 572 outside_port The outside port number or range (only for maps of type napt ). > For a NAPT map: Represents the range of TCP/UDP ports to be used as dynamic port ra nge during the NAPT process. > For a port-shifting map: Repr esen ts the source port(s) to be translated (shifted) into inside_port .
E-DOC-CTC-20061 027-0003 v2.0 NAT Commands 573 EXAMPLE: RELA TED COMMANDS: =>nat maplist Idx Type Interface Outside Address Inside Address Use 1 NAPT eth0 any:80 127.0.0.1:8080 0 2 NAPT eth0 any:1080 127.0.0.1:8080 0 3 NAPT eth0 any:8080 127.0.0.1:8080 0 =>nat mapadd intf=myPPP_ppp type=napt outside_addr=100.
E-DOC-CTC- 20061027-0003 v2 .0 NAT Commands 574 nat mapdelete Delete an address mapping from a NA T enabled interface. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: nat mapdelete intf = <string> index = <number> intf The IP interface name. REQUIRED index The map ind ex.
E-DOC-CTC-20061 027-0003 v2.0 NAT Commands 575 nat maplist Display the address mapping for a NA T enabled interface. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: nat maplist [intf = <string>] [expand = <{disabled | enabled}>] [string = <string>] [beginstring = <string>] intf The IP in terface name.
E-DOC-CTC- 20061027-0003 v2 .0 NAT Commands 576 nat tmpladd Add an address mapp ing template. SYNT AX: where: nat tmpladd [intf = <string>] [group = <{wan|local|lan|tunnel|dmz|guest} or numbe.
E-DOC-CTC-20061 027-0003 v2.0 NAT Commands 577 outside_addr The outside (typ ically public) IP ad dress. > Inbound: This map will only apply if the destination IP address is part of the outside address(es). > Outbound: Represe nts the address(es) to be used as sour ce address after translation.
E-DOC-CTC- 20061027-0003 v2 .0 NAT Commands 578 protocol The IP protocol to be used as filter for inb ound/outbound traffi c. The NA T map only applies if the pr otocol of t he IP packet matches the map protocol . Select an IP proto col (see “ Supported IP Pro tocols” on page 74 6 ) or , alternativ ely , type the protoc ol number .
E-DOC-CTC-20061 027-0003 v2.0 NAT Commands 579 EXAMPLE: RELA TED COMMANDS: =>nat tmpladd intf=myPPP_ppp type=napt outside_addr=100.100.100.1 =>nat tmpllist Idx Type Interface Ifgroup Outside Address Inside Address Use 1 NAPT myPPP_ppp any 100.100.
E-DOC-CTC- 20061027-0003 v2 .0 NAT Commands 580 nat tmpldelete Delete an address mapping template. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: nat tmpldelete index = <number> index The index of the address ma pping template to be deleted. Ti p Use the command :nat tm pllist to view the address mapping templates.
E-DOC-CTC-20061 027-0003 v2.0 NAT Commands 581 nat tmpllist Display the address mapping templates. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: nat tmpllist [expand = <{disabled | enabled}>] expand Enable or disabl e expanded listing . The default is disabled .
E-DOC-CTC- 20061027-0003 v2 .0 NAT Commands 582 nat tmplinst Instantiate address mappin g templates fo r a given dy namic address. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: nat tmplinst intf = <string> addr_index = <ip-address> dynamic_addr = <ip-address> intf The IP interface name.
E-DOC-CTC-20061 027-0003 v2.0 PPP Commands 583 30 PPP Commands Introduction This chapter describes the commands of the ppp comman d group. Contents This chapter covers th e following commands: ppp flush Flush all PPP in terfaces. 584 ppp ifadd Create a new PPP inter face.
E-DOC-CTC- 20061027-0003 v2 .0 PPP Commands 584 ppp flush Flush all PPP interfaces. SYNT AX: i The flush command do es not impact previously save d configuration s.
E-DOC-CTC-20061 027-0003 v2.0 PPP Commands 585 ppp ifadd Create a new PPP interface. SYNT AX: where: EXAMPLE: ppp ifadd intf = <string> intf The name for the new PPP interface. Note If not specified, th e destination parameter mus t be specified.
E-DOC-CTC- 20061027-0003 v2 .0 PPP Commands 586 RELA TED COMMANDS: ppp ifdelete Delete a PPP interface. ppp iflist Display the PPP interfaces..
E-DOC-CTC-20061 027-0003 v2.0 PPP Commands 587 ppp ifattach Attach a PPP interface. SYNT AX: where: ppp ifattach intf = <string> intf The name of the PPP interface to be attached.
E-DOC-CTC- 20061027-0003 v2 .0 PPP Commands 588 EXAMPLE: RELA TED COMMANDS: =>ppp iflist Internet: dest : RELAY [00:00:00] Retry : 10 mode = IP routing flags = echo magic accomp restart mru addr sa.
E-DOC-CTC-20061 027-0003 v2.0 PPP Commands 589 ppp ifconfig Configure a PPP interface. SYNT AX: where: i The interface to be configured must not be connected at the time of configuration. If this should be the case, use the command :p pp ifdetach before usin g the command :ppp ifconfi g.
E-DOC-CTC- 20061027-0003 v2 .0 PPP Commands 590 password The password for remote P AP/CHAP authentication. OPTIONAL acname The Access Concentr ator name for a PPPoE session. Ti p Use the command :ppp ifscan to obtain the names of available access concentrators, if any .
E-DOC-CTC-20061 027-0003 v2.0 PPP Commands 591 silent Do not send anything at startup and just li sten for incoming LCP messages (enabled) or retry up to 10 times to establish the connection (disabled). The default is disabled . OP TIONAL echo Send LCP echo requests at regular intervals (enabled) or not (disabled).
E-DOC-CTC- 20061027-0003 v2 .0 PPP Commands 592 dnsmetric A number between 1 and 100. Represents the DNS route metric to be used for the negotiated DNS servers. The default is 1 . OP TIONAL idletime A number between 0 and 10000 00 (seconds). Represents the maxi mum time the link may be idle.
E-DOC-CTC-20061 027-0003 v2.0 PPP Commands 593 EXAMPLE: =>ppp iflist Internet: dest : RELAY [00:00:00] Retry : 10 mode = IP routing flags = echo magic accomp restart mru addr savepwd demanddial dns.
E-DOC-CTC- 20061027-0003 v2 .0 PPP Commands 594 ppp ifdelete Delete a PPP interfa ce. SYNT AX: where: EXAMPLE: ppp ifdelete intf = <intfname> intf The name of the PPP interface to be deleted.
E-DOC-CTC-20061 027-0003 v2.0 PPP Commands 595 RELA TED COMMANDS: ppp ifadd Create a new PPP interface. ppp iflist Display the PPP interfaces..
E-DOC-CTC- 20061027-0003 v2 .0 PPP Commands 596 ppp ifdetach Detach a PPP interface. SYNT AX: where: ppp ifdetach intf = <intfname> intf The name of the PPP interface to be detached .
E-DOC-CTC-20061 027-0003 v2.0 PPP Commands 597 EXAMPLE: RELA TED COMMANDS: =>ppp iflist Internet: dest : RELAY [00:00:00] Retry : 10 mode = IP routing flags = echo magic accomp restart mru addr sav.
E-DOC-CTC- 20061027-0003 v2 .0 PPP Commands 598 ppp iflist Display the PPP interfaces. SYNT AX: where: EXAMPLE INPUT/OUTPUT : RELA TED COMMANDS: ppp iflist [intf = <intfname>] [string = <string>] [beginstring = <string>] intf The name of the PPP interface.
E-DOC-CTC-20061 027-0003 v2.0 PPP Commands 599 ppp ifscan Scan a PPPoE interface fo r available Access Concentrator a nd Service names. SYNT AX: where: EXAMPLE: i Use the command :ppp ifdeta ch for this in terface before performing a scan on it.
E-DOC-CTC- 20061027-0003 v2 .0 PPP Commands 600 ppp rtadd Add a route to the routing table when the PPP link comes up. This route configurati on will determine wh ich local host s are allowed to use this li nk and/or which remote destinations should be or should not be reachable.
E-DOC-CTC-20061 027-0003 v2.0 PPP Commands 601 EXAMPLE: RELA TED COMMANDS: metric The route metric, in other wo rd s, the cost fac tor of the route. Practically , the cost is de termined by the hop count.
E-DOC-CTC- 20061027-0003 v2 .0 PPP Commands 602 ppp rtdelete Delete the route for a PPP link. SYNT AX: where: i The interface must not be connected when a route configuration m u st be deleted. If the interface is connected, use the command :ppp ifde tach for this interface.
E-DOC-CTC-20061 027-0003 v2.0 PPP Commands 603 EXAMPLE: RELA TED COMMANDS: =>ppp iflist Internet: dest : RELAY [00:00:00] Retry : 10 mode = IP routing flags = echo magic accomp restart mru addr sav.
E-DOC-CTC- 20061027-0003 v2 .0 PPP Commands 604 ppp relay flush Remove all Ethernet interfaces from the PPP relay agent list and terminate all sessions.
E-DOC-CTC-20061 027-0003 v2.0 PPP Commands 605 ppp relay ifadd Add an Ethernet interfac e to the PPP relay list. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: ppp relay ifadd intf = <string> intf The Ethernet interf ace to be added to the PPP relay agent list.
E-DOC-CTC- 20061027-0003 v2 .0 PPP Commands 606 ppp relay ifconfig Modify an ethernet interface from the PPP relay agent list. SYNT AX: where: ppp relay ifconfig intf = <string> hwaddr = <hardware-address> inft The ethernet intf to be adde d to the PPP relay agent l ist.
E-DOC-CTC-20061 027-0003 v2.0 PPP Commands 607 ppp relay ifdelete Delete an Ethernet interface from the PPP relay agent list. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: ppp relay ifdelete intf = <string> intf The Ethernet in terface to be delete d from the PPP relay agent list.
E-DOC-CTC- 20061027-0003 v2 .0 PPP Commands 608 ppp relay iflist Display all Ethernet interfaces ad ded to the PPP relay agent list. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: ppp relay iflist intf The Ethernet interf ace to be added to the PPP relay agent list.
E-DOC-CTC-20061 027-0003 v2.0 PPP Commands 609 ppp relay sesslist Add an Ethernet interfac e to the PPP relay list. SYNT AX: where: ppp relay ifadd intf = <string> intf The Ethernet interf ace to be added to the PPP relay agent list.
E-DOC-CTC- 20061027-0003 v2 .0 PPP Commands 610.
E-DOC-CTC-20061 027-0003 v2.0 PPTP Commands 611 31 PPTP Commands Introduction This chapter describes the commands of the pptp command group. Contents This chapter covers th e following commands: pptp ifadd Add a Point-to-Point T unnelin g Protocol (PP TP) profile.
E-DOC-CTC- 20061027-0003 v2 .0 PPTP Commands 612 pptp ifadd Add a Point-to-Point T unneling Protocol (PP TP) profile. SYNT AX: where: i Backwards compatible wi th previous release, us e profiles instead.
E-DOC-CTC-20061 027-0003 v2.0 PPTP Commands 613 pptp flush Flush the complete P PTP configuration. SYNT AX: i The flush command does not impact previously saved configurations.
E-DOC-CTC- 20061027-0003 v2 .0 PPTP Commands 614 pptp list Show the current PP TP configuration. SYNT AX: EXAMPLE: pptp list =>pptp list Dialstr Destination QoS Encaps AC State User DIALUP_PPP3 default vcmux never CONNECTED (10.
E-DOC-CTC-20061 027-0003 v2.0 PPTP Commands 615 pptp profadd Define a new PP TP profile. SYNT AX: where: EXAMPLE: pptp profadd name = <string> [qos = <string>] [encaps = <{vcmux | nlpid}>] [ac = <{never | always | keep}>] name Th e name of the new PP TP profile.
E-DOC-CTC- 20061027-0003 v2 .0 PPTP Commands 616 RELA TED COMMANDS: pptp profdelete Define a new PP TP profile. pptp proflist Display all the curre nt PP TP profiles.
E-DOC-CTC-20061 027-0003 v2.0 PPTP Commands 617 pptp profdelete Delete a PPTP profile. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: pptp profdelete name <string> name Th e name of the PP TP prof ile to be deleted.
E-DOC-CTC- 20061027-0003 v2 .0 PPTP Commands 618 pptp proflist Display all the current PP TP profiles. SYNT AX: EXAMPLE: RELA TED COMMANDS: pptp proflist =>pptp proflist Profile QoS Encaps AC Relay_PPP1 default nlpid always PPTPLink default vcmux never => pptp profadd Define a new PP TP profile.
E-DOC-CTC-20061 027-0003 v2.0 Script Commands 619 32 Script Commands Introduction This chapter describes the commands of the script command group. Scripting is not a g eneral purpose mechan ism but is only used in the autoPVC/ILMI m echanism.
E-DOC-CTC- 20061027-0003 v2 .0 Script Commands 620 script add Add a line to a script. SYNT AX: where: RELA TED COMMANDS: script add name = <string> [index = <number>] command = <quoted string> name Name of the script in which a line must be added.
E-DOC-CTC-20061 027-0003 v2.0 Script Commands 621 script delete Delete a complete script or a line from a script. SYNT AX: where: RELA TED COMMANDS: script delete name = <string> [index = <number>] name Name of the script to be deleted. REQUIRED index Line number to be deleted.
E-DOC-CTC- 20061027-0003 v2 .0 Script Commands 622 script flush Flush all scripts. SYNT AX: i The flush command does not impa ct previously saved configurations.
E-DOC-CTC-20061 027-0003 v2.0 Script Commands 623 script list Display a script or all scripts. SYNT AX: where: EXAMPLE Some of the default scripts are shown below: script list [name = <string>] name Name of the script to be listed. Note If not specified, all th e scripts are displayed.
E-DOC-CTC- 20061027-0003 v2 .0 Script Commands 624 RELA TED COMMANDS: script add Add a line to a scr ipt. script delete Delete a complete script or a line from a script.
E-DOC-CTC-20061 027-0003 v2.0 Script Commands 625 script run Run a script. SYNT AX: where: script run name = <string> pars = <string> name Name of the script to be run. Ti p Use the command :scrip t list to obtain the names of the different scripts.
E-DOC-CTC- 20061027-0003 v2 .0 Script Commands 626.
E-DOC-CTC-20061 027-0003 v2.0 Service Commands 627 33 Service Commands Introduction This chapter describes the commands of the servic e command group. Contents This chapter covers th e following commands: service host assign Assign a service t o a host device.
E-DOC-CTC- 20061027-0003 v2 .0 Service Commands 628 service host assign Assign a service to a host device. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: service host assign name = <quoted string> [host = <ip-address>] [log = <{disabled|enabled}>] name The name of an existing host service.
E-DOC-CTC-20061 027-0003 v2.0 Service Commands 629 service host config Modify and/ or display global service configuration optio ns. SYNT AX: where: EXAMPLE: service host config [trace = <{disabled | enabled}>] trace Enable or disable traces. The default is disabled .
E-DOC-CTC- 20061027-0003 v2 .0 Service Commands 630 service host add Add a host service. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: service host add name = <quoted string> [mode = <{server | client | custom}>] name The name of th e ne w host service.
E-DOC-CTC-20061 027-0003 v2.0 Service Commands 631 service host delete Delete a host service . SYNT AX: where: EXAMPLE: RELA TED COMMANDS: service host delete name = <quoted string> name The name of th e host se rvice to be deleted.
E-DOC-CTC- 20061027-0003 v2 .0 Service Commands 632 service host disable Disable a host service. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: service host disable [name = <quoted string>] name The name of th e host service to be disabled. Note If not specified, all the h ost services will be di sabled.
E-DOC-CTC-20061 027-0003 v2.0 Service Commands 633 service host flush Flush all host services. SYNT AX: service host flush.
E-DOC-CTC- 20061027-0003 v2 .0 Service Commands 634 service host list Display a list of host services. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: service host list [name = <quoted string>] [string = <string>] [beginstring = <string>] name The name of th e host service to be listed .
E-DOC-CTC-20061 027-0003 v2.0 Service Commands 635 service host stats Show the host service statistics. SYNT AX: EXAMPLE: service host stats =>service host stats Services : 113 of 150 in use. Service maps : 225 of 300 in use. Trigger ports: 0 of 25 in use.
E-DOC-CTC- 20061027-0003 v2 .0 Service Commands 636 service host triggerlist List all triggers. SYNT AX: EXAMPLE: service host triggerlist =>service triggerlist Ip Triggerport Portrange Timeout -- .
E-DOC-CTC-20061 027-0003 v2.0 Service Commands 637 service host rule add Create/define a host service portmap. SYNT AX: where: RELA TED COMMANDS: service host rule add name = <quoted string> [pr.
E-DOC-CTC- 20061027-0003 v2 .0 Service Commands 638 service host rule delete Delete a host service portmap. SYNT AX: where: RELA TED COMMANDS: service host rule delete name = <quoted string> [pr.
E-DOC-CTC-20061 027-0003 v2.0 Service Commands 639 service sy stem ifadd Add an interface grou p to the access list. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: service system ifadd name = <string> group = <{wan|local|lan|tunnel|dmz|guest} or number> name The name of th e system serv ice for this access list.
E-DOC-CTC- 20061027-0003 v2 .0 Service Commands 640 service sy stem ifdelete Delete an interface group from the access list. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: service system ifdelete name = <string> group = <{wan|local|lan|tunnel|dmz|guest} or number> name The name of th e system serv ice for this access list.
E-DOC-CTC-20061 027-0003 v2.0 Service Commands 641 service sy stem ipadd Add an IP address (ran ge) to the access list. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: service system ipadd name = <string> ip = <ip-range> name The name of th e system serv ice for this access list.
E-DOC-CTC- 20061027-0003 v2 .0 Service Commands 642 service sy stem ipdelete Delete an IP address (r ange) from the access list. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: service system ipdelete name = <string> ip = <ip-range> name The name of th e system serv ice for this access list.
E-DOC-CTC-20061 027-0003 v2.0 Service Commands 643 service sy stem list Display the system services. SYNT AX: where: service system list [name = <string>] [expand = <{disabled | enabled}>].
E-DOC-CTC- 20061027-0003 v2 .0 Service Commands 644 EXAMPLE: RELA TED COMMANDS: =>service system list Idx Name Protocol SrcPort DstPort Group State -------------------------------------------------.
E-DOC-CTC-20061 027-0003 v2.0 Service Commands 645 service sy stem mapadd Add a port map for a system service. SYNT AX: where: RELA TED COMMANDS: service system mapadd name = <{string}> intf = <{auto|loop|Internet|LocalNetwork}> port = <supported port or number> name The name of the system service for this map.
E-DOC-CTC- 20061027-0003 v2 .0 Service Commands 646 service sy stem mapdelete Delete a port map fo r a system service. SYNT AX: where: RELA TED COMMANDS: service system mapdelete name = <string> intf = <{auto|loop|Internet|LocalNetwork}> port = <supported port or number> name The name of the system service for this map.
E-DOC-CTC-20061 027-0003 v2.0 Service Commands 647 service sy stem modify Modify a system service. SYNT AX: where: RELA TED COMMANDS: service system modify name = <string> [state = <{disabled.
E-DOC-CTC- 20061027-0003 v2 .0 Service Commands 648.
E-DOC-CTC-20061 027-0003 v2.0 SNMP Commands 649 34 SNMP Commands Introduction This chapter describes the commands of the snmp command group. Contents This chapter covers th e following commands: snmp config Show/s et global Simple Network Management Protocol (SNMP) parameters.
E-DOC-CTC- 20061027-0003 v2 .0 SNMP Commands 650 snmp config Show/set glob al Simple Networ k Mana gement Protocol (SNMP) parameters. SYNT AX: where: EXAMPLE: snmp config [sysContact = <quoted string>] [sysName = <quoted string>] [sysLocation = <quoted string>] sysContact The SNMP system contact.
E-DOC-CTC-20061 027-0003 v2.0 SNMP Commands 651 snmp get Get from the supplied SN MP Object IDentifier (OID) . For example: get ObjectId=.1.3.6.1.2.1.1.1.0. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: snmp get [ObjectId = <string>] ObjectID The Object Iden tifier .
E-DOC-CTC- 20061027-0003 v2 .0 SNMP Commands 652 snmp getnext GetNext from the supplied SN MP OID. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: snmp getnext [ObjectId = <string>] ObjectID The Object Identifier . Object ID to getnext from for example .
E-DOC-CTC-20061 027-0003 v2.0 SNMP Commands 653 snmp walk W alk from the supplied SNMP OID. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: snmp walk [ObjectId = <string>] ObjectID The Object Identifier . Object ID to walk from fo r exam ple .1.3.6.
E-DOC-CTC- 20061027-0003 v2 .0 SNMP Commands 654 snmp community add Configure an SNMP com munity string to allow SNMP access over IP . SYNT AX: where: EXAMPLE: RELA TED COMMANDS: snmp community add se.
E-DOC-CTC-20061 027-0003 v2.0 SNMP Commands 655 snmp community delete Delete an SNMP commun ity string to prevent SNMP access over IP . SYNT AX: where: EXAMPLE: RELA TED COMMANDS: snmp community delet.
E-DOC-CTC- 20061027-0003 v2 .0 SNMP Commands 656 snmp community list List all SNMP co mmunity strings in use fo r SNMP access over IP . SYNT AX: EXAMPLE: RELA TED COMMANDS: snmp community list =>sn.
E-DOC-CTC-20061 027-0003 v2.0 SNMP Commands 657 snmp community modify Modify an SNMP community string to allow SNMP access over IP . SYNT AX: where: snmp community modify securityname = <{RWCommunity | ROCommunity}> communityname = <password> securityname Configure access rights/res trictions control for the community name.
E-DOC-CTC- 20061027-0003 v2 .0 SNMP Commands 658 snmp ifadd Create a new SNMP interface. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: snmp ifadd intf = <string> dest = <string> intf The name for the new SNMP interface. REQUIRED dest T he destination interface for this SNMP i nterface.
E-DOC-CTC-20061 027-0003 v2.0 SNMP Commands 659 snmp ifdelete Delete an SNMP interface. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: snmp ifdelete intf = <string> intf The name of the SNMP interf ace. REQUIRED =>snmp ifdelete intf = new :snmp ifdelete intf=new => snmp ifadd Create a new SNMP interface.
E-DOC-CTC- 20061027-0003 v2 .0 SNMP Commands 660 snmp ifattach Attach an SNMP interface. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: snmp ifattach intf = <string> intf The name of the SNMP interface. REQUIRED =>snmp ifattach intf = Internet :snmp ifattach intf=Internet => snmp ifadd Create a new SNMP interface.
E-DOC-CTC-20061 027-0003 v2.0 SNMP Commands 661 snmp ifdetach Detach an SNMP interface. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: snmp ifdetach intf = <string> intf The name of the SNMP interf ace. REQUIRED =>snmp ifdetach intf = Internet :snmp ifdetach intf=Internet => snmp ifadd Create a new SNMP interface.
E-DOC-CTC- 20061027-0003 v2 .0 SNMP Commands 662 snmp ifconfig Modify an SNMP interfac e. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: snmp ifconfig intf = <string> [securityname = <{RWCommunity | ROCommunity}>] [communityname = <password>] intf The name of the SNMP in terface to configu re.
E-DOC-CTC-20061 027-0003 v2.0 SNMP Commands 663 snmp iflist Display the SNMP interfaces. SYNT AX: where: snmp iflist [intf = <string>] intf The name of an SNMP interface to configu re.
E-DOC-CTC- 20061027-0003 v2 .0 SNMP Commands 664.
E-DOC-CTC-20061 027-0003 v2.0 SNTP Commands 665 35 SNTP Commands Introduction This chapter describes the com mands of the Simple N etwork T ime Protocol (SNTP) command grou p. Contents This chapter covers th e following commands: sntp add Add a Network T ime Protocol (NTP ) server to the NT P server list.
E-DOC-CTC- 20061027-0003 v2 .0 SNTP Commands 666 sntp add Add a Network T ime Protocol (NTP ) server to the NTP server list. The internal Thom son ST real time clock (SNTP cl ient) will be synchronized with th e NTP server .
E-DOC-CTC-20061 027-0003 v2.0 SNTP Commands 667 sntp config Modify/disp lay the SNTP client config uration. SYNT AX: where: EXAMPLE: sntp config [state = <{enabled | disabled}>] [poll = <number{1-60}>] [pollpresync = <number{1-60}>] state Enab le or disable the Thomson ST SNTP cli ent.
E-DOC-CTC- 20061027-0003 v2 .0 SNTP Commands 668 sntp delete Delete an NTP server fr om the NTP s erver list. SYNT AX: where: EXAMPLE: RELA TED COMMANDS: sntp delete [addr = <ip-address>] [name = <string>] addr The IP addr ess of the NTP serv er to be removed from the list.
E-DOC-CTC-20061 027-0003 v2.0 SNTP Commands 669 sntp flush Flush the NTP server list and the SNTP client configuratio n. SYNT AX: sntp flush.
E-DOC-CTC- 20061027-0003 v2 .0 SNTP Commands 670 sntp list List the NTP servers. SYNT AX: EXAMPLE: DESCRIPTION: The status of an NTP server can be: > Not used : The Thomso n ST SNTP client is disabled. As a consequence , none of the NTP servers are used.
E-DOC-CTC-20061 027-0003 v2.0 Software Commands 671 36 Software Commands Introduction This chapter describes the commands of the softwa re command grou p. Contents This chapter covers th e following commands: software upgrade Reboot the mo dem to init iate the SW upgrade.
E-DOC-CTC- 20061027-0003 v2 .0 Software Commands 672 software upgrade Reboot the modem to initiate the SW upgrade. New software available on a remote LAN host w ill be uploa ded to the modem.
E-DOC-CTC-20061 027-0003 v2.0 Software Commands 673 software version Display the software version. SYNT AX: software version.
E-DOC-CTC- 20061027-0003 v2 .0 Software Commands 674.
E-DOC-CTC-20061 027-0003 v2.0 System Commands 675 37 Sy stem Commands Introduction This chapter describes the commands of the system command group. Contents This chapter covers th e following commands: system config Set/change the system co nfig uration parameter s.
E-DOC-CTC- 20061027-0003 v2 .0 System Commands 676 sy stem config Set/change the system co nfiguration pa rameters. SYNT AX: where: ! For a good operation o f UPnP and the discovery mechanism, it is hig hly recommended not to change the system co nfiguration settings.
E-DOC-CTC-20061 027-0003 v2.0 System Commands 677 EXAMPLE: autosavedelay A number between 0 and 600. Represents the autosave de lay in seconds (0 for immediate save).
E-DOC-CTC- 20061027-0003 v2 .0 System Commands 678 sy stem flush Flush the curren t system configuration. The system password and the system config settings (dca che excluded) are flushed. SYNT AX: EXAMPLE: i The flush comman d does not impact previously saved configuratio ns.
E-DOC-CTC-20061 027-0003 v2.0 System Commands 679 sy stem locale Set/get the regional settings. SYNT AX: where: system locale [dec_symbol = <{, | .}>] [group_symbol = <{.
E-DOC-CTC- 20061027-0003 v2 .0 System Commands 680 EXAMPLE: time_format Set the time format. Choose betwe en: > iso > hmmss. The default is iso . Note h = hour s; mm = mi nutes; ss = seconds. OP TIONAL datetime_format Set th e date-time format. Choose betwe en: > iso > date+time > time+dat e.
E-DOC-CTC-20061 027-0003 v2.0 System Commands 681 sy stem reboot Reboot the Thomso n ST. SYNT AX: EXAMPLE: RELA TED COMMANDS: ! Non-saved configur ation settings will be lost after reboot. system reboot =>system reboot ..... (lost session connectivity due to reboot) .
E-DOC-CTC- 20061027-0003 v2 .0 System Commands 682 sy stem reset Reset the Thomson ST to its factory or ISP defaults and reboot the device. SYNT AX: where: EXAMPLE: ! All user specific settings and all saved configuration changes are lost after reboot.
E-DOC-CTC-20061 027-0003 v2.0 System Commands 683 RELA TED COMMANDS: sntp config Modify/display the SNTP client configuration..
E-DOC-CTC- 20061027-0003 v2 .0 System Commands 684 sy stem timedreboot Set or change a timed reboot for the Thomson ST. SYNT AX where: EXAMPLE: RELA TED COMMANDS: timedreboot [state = <{disabled|enabled}>] [time = <number{0-16384}>] [date = <string>] state Enable/Disable timed reboot.
E-DOC-CTC-20061 027-0003 v2.0 System Commands 685 sy stem debug autosave Autosave debugg ing commands SYNT AX: where: system debug autosave [trace = <{disabled|enabled}>] trace Enable or di sabl.
E-DOC-CTC- 20061027-0003 v2 .0 System Commands 686 sy stem debug stats Show the Thomson ST CP U and memory statistics. SYNT AX: where: DESCRIPTION: > CHIP memory : Memory used by the CPU (first MB from the RAM) – not cached since it has to be realtime.
E-DOC-CTC-20061 027-0003 v2.0 System Commands 687 sy stem ra config Configure Remote managem ent access parameters. SYNT AX: where: EXAMPLE: system ra config [secure = <{disabled | enabled}>] [port = <number>] [timeout = <number>] secure Enable or disabl e https.
E-DOC-CTC- 20061027-0003 v2 .0 System Commands 688 sy stem rtc synchronize Do a SNTP update and synchron ize the realtime clock. SYNT AX: system rtc synchro- nize.
E-DOC-CTC-20061 027-0003 v2.0 System Commands 689 sy stem rtc settime Set/get date, time, ti mezone, daylig ht savings time, uptime. When synchronization with an exte rnal NTP server via the Thomson ST SNTP client fails, this com mand allows to manuall y configure its internal cl ock.
E-DOC-CTC- 20061027-0003 v2 .0 System Commands 690.
E-DOC-CTC-20061 027-0003 v2.0 Systemlog Commands 691 38 Sy stemlog Commands Introduction This chapter describes the commands of the system log command group. Contents This chapter covers th e following commands: systemlog flush Flush all messages in the inte rnal Syslog message buffer .
E-DOC-CTC- 20061027-0003 v2 .0 Systemlog Commands 692 sy stemlog flush Flush all messages in the inte rnal Syslog message buffer . SYNT AX: systemlog flush.
E-DOC-CTC-20061 027-0003 v2.0 Systemlog Commands 693 sy stemlog show Show messages in the intern al Syslog message buffer . SYNT AX: where: systemlog show [fac = <supported facility name>] [sev = <supported severity name>] [hist = <{disabled | enabled}>] fac Specify the facility name of the syslog messages to be shown.
E-DOC-CTC- 20061027-0003 v2 .0 Systemlog Commands 694 EXAMPLE: =>syslog msgbuf show fac=kern sev=emerg hist=enabled <0> SysUpTime: 14:45:43 KERNEL Controlled restart (after internal error or .
E-DOC-CTC-20061 027-0003 v2.0 Systemlog Commands 695 sy stemlog send Send messages from the inte rnal Syslog message buffer to a specifie d local or remote sy slog server host. SYNT AX: where: i There will be no no tification on whether the host h as received the messages or not.
E-DOC-CTC- 20061027-0003 v2 .0 Systemlog Commands 696 sy stemlog DBG dbg_sy slog Perform a syslog call. SYNT AX: where: systemlog DBG dbg_syslog priority = <number{0-191}> msgstring = <string.
E-DOC-CTC-20061 027-0003 v2.0 Systemlog Commands 697 sy stemlog DBG dbg_long_mess Generate a long sy slog message call. SYNT AX: systemlog DBG dbg_long_mess.
E-DOC-CTC- 20061027-0003 v2 .0 Systemlog Commands 698 sy stemlog DBG dbg_burst Perform a syslog message burst. SYNT AX: systemlog DBG dbg_burst.
E-DOC-CTC-20061 027-0003 v2.0 Systemlog Commands 699 sy stemlog DBG dbg_contents Show the contents of the message buffer . SYNT AX: systemlog DBG dbg_contents.
E-DOC-CTC- 20061027-0003 v2 .0 Systemlog Commands 700.
E-DOC-CTC-20061 027-0003 v2.0 Upgrade Commands 701 39 Upgrade Commands Introduction This chapter describes the commands of the upgrad e command group. Contents This chapter covers th e following commands: upgrade config Change the upgrade daemon con figuration.
E-DOC-CTC- 20061027-0003 v2 .0 Upgrade Commands 702 upgrade config Change the upgrade d aemon configuration. SYNT AX: where: EXAMPLE: upgrade config [state = <{disabled|enabled}>] [protocol = <{tftp|ftp|http|https}>] state Set the upgrade daemon st ate to enabled or disabled.
E-DOC-CTC-20061 027-0003 v2.0 Upgrade Commands 703 upgrade start Start a new upgrade. SYNT AX: where: upgrade start protocol = <{tftp|ftp|http|https}> [server = <string>] [filename = <string>] protocol The protoco l to be used fo r the download.
E-DOC-CTC- 20061027-0003 v2 .0 Upgrade Commands 704 upgrade debug traceconfig Enable/disable up grade daemon tracing. SYNT AX: where: upgrade debug traceconfig state = <{disabled|enabled}> state Set the upgared daemon state to enabled or disabled .
E-DOC-CTC-20061 027-0003 v2.0 Upgrade Commands 705 upgrade debug sesslist Display the list of sessions. SYNT AX: EXAMPLE: upgrade debug sesslist =>:upgrade debug sesslist Session 0: --------------------------------------------------------------- SessionId : 0x80c25850 State : IDLE Protocol : TFTP ServerName: FileName : DestFile : ServerIP : 0.
E-DOC-CTC- 20061027-0003 v2 .0 Upgrade Commands 706 upgrade profile add Add a new file profile description. SYNT AX: where: RELA TED COMMANDS: upgrade profile add extension = <{sts|ini}> [maxsize(KBytes) = <number>] action = <{none|config_load|script_load|reboot}> extension The extension of the new file profile.
E-DOC-CTC-20061 027-0003 v2.0 Upgrade Commands 707 upgrade profile modify Modify a file profile desc ription. SYNT AX: where: RELA TED COMMANDS: upgrade profile modify extension = <{sts|ini}> [maxsize(KBytes) = <number>] action = <{none|config_load|script_load|reboot}> extension The extension of the new file profile.
E-DOC-CTC- 20061027-0003 v2 .0 Upgrade Commands 708 upgrade profile delete Delete a file profile description. SYNT AX: where: RELA TED COMMANDS: upgrade profile delete extension = <{sts|ini}> extension The extension of the profi le to be deleted.
E-DOC-CTC-20061 027-0003 v2.0 Upgrade Commands 709 upgrade profile list Display a list of the file profile descriptions. SYNT AX: RELA TED COMMANDS: upgrade profile list upgrade profile delete De lete a file profile descrip tion. upgrade profile modify Modify a file profile description.
E-DOC-CTC- 20061027-0003 v2 .0 Upgrade Commands 710 upgrade ifadd Add a download interface. SYNT AX: where: RELA TED COMMANDS: upgrade ifadd intf = <string> intf A download interface REQUIRED.
E-DOC-CTC-20061 027-0003 v2.0 Upgrade Commands 711 upgrade ifattach Attach a download interface. SYNT AX: where: RELA TED COMMANDS: upgrade ifattach intf = <string> intf A download interface REQ.
E-DOC-CTC- 20061027-0003 v2 .0 Upgrade Commands 712 upgrade ifconfig Configure a download interface. SYNT AX: where: RELA TED COMMANDS: upgrade ifconfig intf = <string> [protocol = <{tftp|ftp.
E-DOC-CTC-20061 027-0003 v2.0 Upgrade Commands 713 upgrade ifdelete Delete a download interface. SYNT AX: where: RELA TED COMMANDS: upgrade ifdelete intf = <string> intf A download interface REQ.
E-DOC-CTC- 20061027-0003 v2 .0 Upgrade Commands 714 upgrade ifdetach Detach a download interface. SYNT AX: where: RELA TED COMMANDS: upgrade ifdetach intf = <string> intf A download interface RE.
E-DOC-CTC-20061 027-0003 v2.0 Upgrade Commands 715 upgrade iflist List all downlo ad interfaces. SYNT AX: RELA TED COMMANDS: upgrade iflist.
E-DOC-CTC- 20061027-0003 v2 .0 Upgrade Commands 716.
E-DOC-CTC-20061 027-0003 v2.0 UPnP Commands 717 40 UPnP Commands Introduction This chapter describes the commands of the upnp command group. Contents This chapter covers th e following commands: upnp config Configure the UPnP™ parameter(s). 718 upnp flush Flush the UPnP™ con figuration.
E-DOC-CTC- 20061027-0003 v2 .0 UPnP Commands 718 upnp config Configure the UPnP™ parameter(s). SYNT AX: where: upnp config [maxage = <number{60-999999}>] [writemode = <{full | natonly | rea.
E-DOC-CTC-20061 027-0003 v2.0 UPnP Commands 719 upnp flush Flush the UPnP™ conf iguration. The UP nP configuratio n will be reset to the default configur ation.
E-DOC-CTC- 20061027-0003 v2 .0 UPnP Commands 720 upnp list List all registered devices. SYNT AX: where: EXAMPLE: i Use this command to check whether a PPP connection is properly configured and thus advertised as a PPP service. upnp list [verbose = <number{0-2}>] verbose V erbose level.
E-DOC-CTC-20061 027-0003 v2.0 User Commands 721 41 User Commands Introduction This chapter describes the commands of the user command group. Contents This chapter covers th e following commands: user add Add a user . 722 user config Modify a user . 724 user delete Delete a user .
E-DOC-CTC- 20061027-0003 v2 .0 User Commands 722 user add Add a user . SYNT AX: where: i Y ou can only add a user whos e privileges are the same or l ower than your own privil eges.
E-DOC-CTC-20061 027-0003 v2.0 User Commands 723 EXAMPLE: In the examp le below , the user Adm i nistrator creates a new user JohnDoe. This user has lo wer access rights than the user “Poweruser”. DESCRIPTION: > U : indicates the default user . > R : indicates the default remote a dministrator .
E-DOC-CTC- 20061027-0003 v2 .0 User Commands 724 user config Modify a user . SYNT AX: where: i Y ou can only modify a user whose privileges ar e the same or lower than your own privileges.
E-DOC-CTC-20061 027-0003 v2.0 User Commands 725 EXAMPLE: {Superuser}=>user list User Role ==== ==== Superuser root aPoweruser Poweruser {Superuser}=>user config name=aPoweruser role=LAN_admin {S.
E-DOC-CTC- 20061027-0003 v2 .0 User Commands 726 user delete Delete a user . SYNT AX: where: EXAMPLE: RELA TED COMMANDS: i Y ou can only delete a user whose privileges ar e the same or lower than your o wn privileges. user delete name = <string> name The name of th e user to be deleted.
E-DOC-CTC-20061 027-0003 v2.0 User Commands 727 user flush Flush the use rs. SYNT AX: EXAMPLE: When this T elnet session is termin ated and a new T e lnet session is in itiated, the follo wi ng welcome screen will appear: The user will not have to auth entic ate himself to gain access to th e Thomson ST.
E-DOC-CTC- 20061027-0003 v2 .0 User Commands 728 user list Display the users. SYNT AX: where: user list [name = <string>] [channel = <{ftp | telnet | http | mdap | serial}>] [origin = <{lan | wan | local}>] [secure = <{disabled | enabled}>] name The user name .
E-DOC-CTC-20061 027-0003 v2.0 User Commands 729 EXAMPLE: RELA TED COMMANDS: {Administrator}=>user list User Flags Role ---- ----- ---- Administrator U Administrator tech R TechnicalSupport {Adminis.
E-DOC-CTC- 20061027-0003 v2 .0 User Commands 730 user rights Display the session rights. SYNT AX: EXAMPLE: i The user rights of the curren tly logged-in user are shown.
E-DOC-CTC-20061 027-0003 v2.0 Abbreviations 731 42 Abbreviations The table below lists all the abbreviatio ns used in the CLI Reference Guide. Abbreviation Description AAL5 A TM Ada ption Layer 5 ACL .
E-DOC-CTC- 20061027-0003 v2 .0 Abbreviations 732 HTTP HyperT ext T ransfer Protocol ICMP Internet Control M essage Protocol IDS Intrusion Detection System IGD Internet Gateway Device IGMP Internet Gro.
E-DOC-CTC-20061 027-0003 v2.0 Abbreviations 733 PPPoA PPP over A TM PPPoE PPP over Ethernet PPTP Point-to-Point T u nneling Protocol PSD Power Spectral Densi ty PSK Pre-Shared Key PVC Permanent Virtua.
E-DOC-CTC- 20061027-0003 v2 .0 Abbreviations 734 VLSM V ariable Length Subnet Masking VP Vir t ua l P at h VPI V irtual Path Identifier VPN Virtual Private Networking WA N Wide Area Network WDS Wirele.
E-DOC-CTC-20061 027-0003 v2.0 System Logging Messages 735 43 Sy stem Logging Messages Introduction This chapter lists the differe nt System Logging messages.
E-DOC-CTC- 20061027-0003 v2 .0 System Logging Messages 736 Auto-PVC Module Configuration Module DHCP Client Module Facility Severity Contents LOCAL5 W ARNING AUTOPVC scrip t <script_name> failed.
E-DOC-CTC-20061 027-0003 v2.0 System Logging Messages 737 DHCP Relay Module DHCP Server Module Facility Severity Contents LOCAL2 W ARNING DHCR relay: D ropping boot rq s on interface <intf_id> d.
E-DOC-CTC- 20061027-0003 v2 .0 System Logging Messages 738 Dyndns Module Firewall Module Facility Severity Contents DYNDNS W ARNING <DYNDNS_ STR_ID> Connection failed to <dynd ns_service> .
E-DOC-CTC-20061 027-0003 v2.0 System Logging Messages 739 LOGIN Module Kernel Module Linestate Module NAPT Module Facility Severity Contents AUTH NOTI CE LOG OUT User <user_i d> logged o ut on &.
E-DOC-CTC- 20061027-0003 v2 .0 System Logging Messages 740 PPP Module PPTP Module Facility Severity Contents LOCAL0 W ARNING PPP Link u p (<intf name>) LOCAL0 WA R N I N G PP P Link down (<in.
E-DOC-CTC-20061 027-0003 v2.0 System Logging Messages 741 RIP Module Facility Severity Contents LOCAL1 INFO RIP Packet received from unk nown interface LOCAL1 INFO RIP Packet size is sma ller than min.
E-DOC-CTC- 20061027-0003 v2 .0 System Logging Messages 742 Routing Module Session Module SNTP Module LOCAL1 I NFO RIP IP Address <ip-address> not found in RIP tabl e Facility Severity Contents L.
E-DOC-CTC-20061 027-0003 v2.0 System Logging Messages 743 Software Module UPnP Module Facility Severity Contents KERN INFO SOF TW ARE File <Filename> <r eceive || transmit> initiated KERN .
E-DOC-CTC- 20061027-0003 v2 .0 System Logging Messages 744.
E-DOC-CTC-20061 027-0003 v2.0 Supported Key Names 745 44 Supported Key Names Contents This chapter lists all the key names supported by the Thomson ST, tha t can be used for completi ng CLI command pa.
E-DOC-CTC- 20061027-0003 v2 .0 Supported Key Names 746 Supported IP Protocols For more information on the listed IP protocols, see RFC1340 or www.iana.
E-DOC-CTC-20061 027-0003 v2.0 Supported Key Names 747 Supported TCP/UDP Port Names For more informati on on the listed TCP/UDP po rt assignments, see RFC1340 or www .
E-DOC-CTC- 20061027-0003 v2 .0 Supported Key Names 748 sntp 123 Y Y Simple Network T ime Protocol (SNTP) ingres-net 134 Y Y INGRES -NET Service netbios-ns 137 Y Y NE TBIOS Naming System netbios-dgm 13.
E-DOC-CTC-20061 027-0003 v2.0 Supported Key Names 749 ntalk 518 Y Y NT alk utime 519 Y Y UNIX T ime rip 520 - Y Local routing process (on site); uses variant of Xerox NS Routing Information Proto col .
E-DOC-CTC- 20061027-0003 v2 .0 Supported Key Names 750 Supported ICMP T ype Names For more information on the listed ICMP type names, see RFC1340 or www .
E-DOC-CTC-20061 027-0003 v2.0 Supported Key Names 751 Supported Facilities For more information on the listed facilities, see RFC3164. Facilty Name Hierarchy Code Syslog facility (listed accor ding de.
E-DOC-CTC- 20061027-0003 v2 .0 Supported Key Names 752 Supported Severities For more information on the li sted severities, see RFC3164. IP Precedence Severity Name Hierarchy Code Syslog severity (lis.
E-DOC-CTC-20061 027-0003 v2.0 Supported Key Names 753 Differentiated Services Code Point (DSCP) For more information on DSCP , see RFC3260. PHB PHB Name Binary value ef Expe dited Forwarding 101110 af.
E-DOC-CTC- 20061027-0003 v2 .0 Supported Key Names 754.
Index E-DOC-CTC-20061 027-0003 v2.0 755 A aal5stats atm debug aal5stats 41 actlist eth bridge dynvlan actlist 265 add atm bundle add 27 atm oam vclb add 52 atm phonebook add 55 atm qosbook add 60 dhcp.
Index E-DOC-CTC-2006 1027-0003 v2.0 756 add 55 autolist 56 delete 57 flush 58 list 59 qosbook add 60 config 61 ctdadd 62 ctddelete 64 ctdlist 65 delete 66 flush 67 list 68 attach atm bundle attach 28 .
Index E-DOC-CTC-20061 027-0003 v2.0 757 service host config 629 snmp config 650 sntp config 667 system config 676 system ra config 687 upgrade config 702 upnp config 718 user config 724 connection app.
Index E-DOC-CTC-2006 1027-0003 v2.0 758 optionlist 125 txoptions add 126 delete 127 list 128 relay add 130 config 133 debug stats 131 traceconfig 132 delete 134 flush 135 ifconfig 136 iflist 138 list .
Index E-DOC-CTC-20061 027-0003 v2.0 759 delete 221 flush 222 list 223 modify 224 dump config dump 75 dyndns add 228 delete 229 flush 230 host add 234 delete 235 flush 236 list 237 list 231 modify 232 .
Index E-DOC-CTC-2006 1027-0003 v2.0 760 iflist 322 vlan add 323 delete 324 flush 325 list 326 exec debug exec 106 mbus client exec 519 export mlp debug ex port 546 expr add 328 delete 332 flush 334 li.
Index E-DOC-CTC-20061 027-0003 v2.0 761 G get env get 245 snmp get 651 snmp getnext 652 getaddress dns server debug spoof getaddress 195 getflags dns server debug spoof getflags 196 grouplist igmp pro.
Index E-DOC-CTC-2006 1027-0003 v2.0 762 atm ifdelete 24 dhcp client ifdelete 113 eth bridge ifdelete 276 eth bridge vlan ifdelete 299 eth ifdelete 255 ip auto ifdelete 464 ip ifdelete 443 ppp ifdelete.
Index E-DOC-CTC-20061 027-0003 v2.0 763 iflist 445 ifwait 446 ipadd 447 ipconfig 448 ipdelete 449 iplist 450 mcast flush 454 rtadd 451 rtdelete 452 rtlist 453 rtadd 455 rtdelete 457 rtlist 458 ipadd i.
Index E-DOC-CTC-2006 1027-0003 v2.0 764 eth switch qos list 316 eth switch share list 312 eth vlan list 326 expr list 335 firewall chain list 354 firewall level li st 361 firewall list 347 firewall ru.
Index E-DOC-CTC-20061 027-0003 v2.0 765 list 555 removezone 557 role add 558 addpriv 560 config 561 delete 562 list 563 removepriv 564 modify atm oam cc modify 50 atm oam modify 46 dhcp rela y modify .
Index E-DOC-CTC-2006 1027-0003 v2.0 766 profdelete pptp profdelete 617 proflist pptp proflist 618 proxy dsd debug proxy 213 R reboot system reboot 681 recycling dsd debug recycling 214 refresh connect.
Index E-DOC-CTC-20061 027-0003 v2.0 767 set env set 247 firewall level set 363 settime system rtc settime 689 show grp rip show 3 85 systemlog show 693 snmp community add 654 delete 655 list 656 modif.
Index E-DOC-CTC-2006 1027-0003 v2.0 768 nat tmpladd 576 tmpldelete dhcp server option tmpl delete 166 nat tmpldelete 580 tmplinst nat tmplinst 582 tmpllist dhcp server option tmpl list 167 nat tmpllis.
.
THOMSON Telecom Belgium Prins Boudewijnlaan 47 2650 Edegem www .thomson-broadband.com © THOMSON . All right s reserved. E-DOC-CTC-20061027-0003 v2.0..
Ein wichtiger Punkt beim Kauf des Geräts Technicolor - Thomson ST536 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Technicolor - Thomson ST536 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Technicolor - Thomson ST536 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Technicolor - Thomson ST536 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Technicolor - Thomson ST536 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Technicolor - Thomson ST536 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Technicolor - Thomson ST536 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Technicolor - Thomson ST536. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Technicolor - Thomson ST536 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
