Benutzeranleitung / Produktwartung thick shake freezers des Produzenten Taylor
Zur Seite of 40
Models 358 & 359 Th ick S hake F reezers Opera ting Instruc tions 056788-M 8/2/ 10 (Or igi nal Publi cation) (Updat ed 3/18/ 11).
Com plete this page for quick r efer ence when ser vice is r equir ed: Taylor Distributor: Address: Phone: Serv ice: Par ts: Date of Installation: Infor mation found on the data label: Model Number: Seri al Number: Electrical S pecs: Voltage Cycle Phase Maximum Fuse Si ze: A Minimum Wi re Ampacity : A E August , 2010 T aylor All right s res erved.
Models 3 58 & 3 59 Table of Cont ents Table of Contents Section 1 To the Installer 1 ............................................ Installer Safety 1 ........................................................ Site P reparation 1 .....................
Table of Cont ents Mode ls 358 & 3 59 Table of Contents - P age 2 Cleaning 19 ............................................................. Disassemb ly 19 .......................................................... Brush Cleani ng 19 .............
1 Mo del s 358 & 359 To the Insta ller Section 1 To the Installer The f ollowing are general ins tallat ion inst ruct ions. For com plete ins tallat ion details , please s ee the checko ut card. Installer Safety In all ar eas of t he world, equipm ent s hould be installed in ac cordanc e with exis ting loc al codes.
2 Mo del s 358 & 359 To the Insta ller 110318 Air Cooled Units DO NOT obst ruc t air int ake and dis charge openings: Air cooled units r equire a minimum of 3” ( 76 mm) of clearanc e around all sides of the f reezer s and 3-1/ 2” (89 mm) on the bo tt om.
3 Mo del s 358 & 359 To the Insta ller Refr igerant In cons iderat ion of our env ironment , T aylor proudly uses only ear th fr iendly HFC ref rigerant s. The HF C ref rigerant used in this unit is R404A. T his ref rigerant is gener ally consider ed non-toxic and non-f lammable, wit h an O zone Depleting P otent ial (O DP) of z ero (0) .
4 Mo del s 358 & 359 To the Opera tor Section 2 To the Operator Your f reezer s have been car efully engineer ed and manuf actur ed to give y ou dependable operat ion. Thes e units, when properly oper ated and c ared for , will produce a c onsist ent qualit y produc t.
5 Mo del s 358 & 359 Safety Se cti on 3 Sa fety We, at T aylor Company, ar e concerned about the safet y of the operat or when he or s he comes in contac t wit h the f reez er and its par ts. Tay lor has gone to ext rem e eff ort s to des ign and manuf actur e built- in safet y f eatur es to pr otect both y ou and the serv ice tec hnician.
6 Mo del s 358 & 359 Safety S DO NOT allow unt rained pers onnel to operat e this m achine. S DO NOT operat e t he freez er unless all serv ice panels and access doors ar e restrain ed with screws. S DO NOT rem ove any int ernal oper ating part s (examples: f reez er door, beater, scr aper blades, et c.
7 Mo del s 358 & 359 Op erato r Parts I den ti fi cati on Section 4 Operator Parts Identif ication Model 358 Figur e 1 ITE M DESCRIPTI ON PART NO. 1 COVER A.- HOPPER INSUL X51658 2 TUBE-FEED- NONREVERS 015176-5 3 PANEL-REAR 046021 4 PANEL-SI DE *358* RI GHT 046023-SP1 5 FILTER A.
8 Mo del s 358 & 359 Op erato r Parts I den ti fi cati on Model 359 Figur e 2 ITE M DESCRIPTI ON PART NO. 1 PANEL-SI DE-LEFT 065250 2 COVER ASSEMBLY-HOPPER X51658 3 TUBE-FEED- NONREVERSIBLE 015176-5 4 PANEL-REAR 065271 5 FILTER- AIR 18 L X 13. 5 H X .
9 Mo del s 358 & 359 Op erato r Parts I den ti fi cati on Beater and Door Assem bly Figur e 3 ITE M DESCRIPTI ON PART NO. 1 SEAL-DRI VE SHAFT 032560 2 SHAFT-BEATER 033235 3 BEATER A.- 7 QT. - 1 PIN X46233 4 BEARING- FRONT 013116 5 GASKET-DOOR - 5.
10 Mo del s 358 & 359 Op erato r Parts I den ti fi cati on Accessor ies Figur e 4 ITE M DESCRIPTI ON PART NO. 1 KIT ASSEMBLY- TUNE UP *358 X46050 KIT ASSEMBLY- TUNE UP *359 X36356 2 BRUSH-REAR BEARI NG 013071 3 BRUSH-DOUBLE ENDED 013072 ITE M DESCRIPTI ON PART NO.
11 Models 3 58 & 3 59 Impor tant: To the Oper ator Section 5 Important: To the Operator Model 358 Model 359 Figur e 5 Figur e 6 ITE M DESCRIPTI ON 1 POWER SWITC H 2 MIX OUT I NDICATOR 3 RESET BUTT.
12 Mo del s 358 & 359 Impor tant: To the Oper ator Power Switch The m iddle position is “ OF F” . T he left position is “W ASH”, which act ivat es the beat er m otor only . T he right pos ition is “ AUT O”, which act ivat es the beat er motor and the re frigeration system.
13 Mo del s 358 & 359 Op erati ng P roced ures Section 6 Operating Procedures The M odel 358 has been select ed t o show you t he pict ured st ep-by- step oper ating pr ocedures f or bot h models c ontained in t his manual. T hese m odels, f or pract ical purpos es of oper ation, ar e the s ame.
14 Mo del s 358 & 359 Op erati ng P roced ures Step 3 Check the sc raper blades f or any nicks or s igns of wear. I f any nic ks ar e present , r eplace both blades . If the blades ar e in good condition, inst all the scr aper blade clips on t he sc raper blades.
15 Mo del s 358 & 359 Op erati ng P roced ures Step 8 Place t he fr eezer door gas ket int o t he groove on t he back of the f reezer door . S lide the whit e plastic front bearing over t he baff le rod ont o the bear ing hub, making c ertain t he f langed end of t he bearing is rest ing against the freez er door.
16 Mo del s 358 & 359 Op erati ng P roced ures Sani tizing Step 1 Prepar e an approved 100 PP M sanit izing solut ion (exam ples: 2-1/ 2 gal. [9.5 liters ] of Kay- 5 R or 2 gal. [7. 6 liters] of S tera- Sheen R ). USE WARM WA- TER A ND FO LLOW THE M ANUF ACTURE R'S SPECIFICATI ONS.
17 Mo del s 358 & 359 Op erati ng P roced ures Step 6 Stand t he air t ube in the c orner of the mix hopper . Figur e 25 Re peat St eps 1 thr ough 6 for t he other s ide of t he fr eezer on t he Model 359. Prim ing Step 1 Wit h a pail beneath t he door s pout, r aise t he draw handle.
18 Mo del s 358 & 359 Op erati ng P roced ures Step 5 Place t he mix hopper c over in pos ition over t he mix hopper. Figur e 29 Re peat St eps 1 thr ough 5 for t he other s ide of t he fr eezer on t he Model 359.
19 Mo del s 358 & 359 Op erati ng P roced ures Cleaning Step 1 Prepar e an approved 100 PP M cleaning s olution (exam ples: 2-1/ 2 gal. [9.5 liters ] of Kay- 5 R or 2 gal. [7. 6 liters] of S tera- Sheen R ). USE WARM WAT ER A ND FO LLOW T HE M ANUFA CTURER' S SPECIFICATI ONS.
20 Mo del s 358 & 359 Op erati ng P roced ures Step 5 Return t o t he freez er wit h a small amount of cleaning solut ion. W ith t he black br istle br ush, br ush clean t he rear shell bear ing(s) at the back of the freez ing cylinder (s) .
21 Models 3 58 & 3 59 Impor tant: Ope rat or Chec klis t Section 7 Important: Operator Checklist Dur ing Cl eaning and Sani tizing ALWAYS FOLLOW LOCAL HEALTH CODES. Clean in g and san i tiz in g sched u les are govern ed by fe der al, st ate , or loca l re gulator y age ncie s, and must b e fo ll ow ed acco rdi n gl y.
22 Mo del s 358 & 359 Impor tant: Ope rat or Chec klis t j 4. Dispose of o-rings and s eals if t hey ar e worn, torn, or f it t oo loosely, and replace wit h new ones. j 5. Follow all lubr icating pr ocedures as out lined in “Assembl y”. j 6. If y our machine is air cooled, check t he condenser f or acc umulat ion of dirt and lint.
23 Models 3 58 & 3 59 Trouble shooting Guide Section 8 Troubleshooting Guide PROBL EM PROBABLE CAUSE REMEDY PAGE REF. 1. No product is being dispensed wit h draw valv e open and machine in t he “AUT O” m ode. a. Beat er mot or is out on reset.
24 Mo del s 358 & 359 Trouble shooting Guide PROBL EM PROBABLE CAUSE REMEDY PAGE REF. 6. The dri ve shaf t is s tuc k in the dri ve coupling. a. Mix and lubr icant c ollect ed in the driv e coupling. a. Br ush clean t he rear s hell bearing area r egularly.
25 Models 3 58 & 3 59 Trouble shooting Guide PROBL EM PROBABLE CAUSE REMEDY PAGE REF. 11. Product is not feeding into the f reezing c ylinder. a. I nadequate lev el of mix i n the m ix hopper. a. Fill t he mix hopper wit h mix. 17 b. Mix inlet hole fr ozen up.
26 Mo del s 358 & 359 Parts Rep lacemen t S ched ul e Section 9 Parts Replacement Schedule PART DESCRIPTI ON EVERY 3 MONTHS EVERY 4 MONTHS EVERY 6 MONTHS ANNUALLY 358 QTY.
Section 10 Parts List 27 Mo del s 358 & 359 Parts List 1 10318 DESCRI PT IO N PART NUMBER QTY. 358 QTY. 359 WARR. CLASS RE MARKS ARM A.- IDLER * 356* X64892 1 2 103 + BRACKET-I DLER ARM 045912 1 2 103 + BOLT-I DLER PULLEY *358* 046039 1 2 103 + SCREW-SHOULDER 046048 1 2 000 + SPRING- EXTENSION.
28 Parts List Mod els 358 & 359 DESCRI PT IO N REMARKS WARR. CLASS QTY. 359 QTY. 358 PART NUMBER CAPACITOR- RUN 7.5UF/370V 034749 1 103 BLOWER FAN CASTER-LOCKI NG SWIVEL 3 IN.
29 Mo del s 358 & 359 Parts List DESCRI PT IO N REMARKS WARR. CLASS QTY. 359 QTY. 358 PART NUMBER FILTER- CORCOM 2VR1 032567 1 2 000 GUIDE A. -DRIP PAN* 358*W/ SHROUD X68531 1 000 208- 230V 60HZ 1PH GUIDE A. -DRI P PAN *358* 359 X45985 1 2 103 208-230V 60HZ 3PH HARNESS A.
30 Parts List Mod els 358 & 359 DESCRI PT IO N REMARKS WARR. CLASS QTY. 359 QTY. 358 PART NUMBER LABEL-WARN- CONDENSER-SHARP 059287 1 3 000 LABEL-WARN- COVER 051433 5 5 000 LIGHT- AMBER 075724 1 2 103 LUBRICANT- TAYLOR 4 OZ. 047518 1 1 000 MAN-O PER 358/359 056788-M 1 1 000 MOTOR-1.
31 Mo del s 358 & 359 Parts List DESCRI PT IO N REMARKS WARR. CLASS QTY. 359 QTY. 358 PART NUMBER + BOLT-I DLER PULLEY *358* 046039 1 2 103 RELAY-3 POLE- 20A-208/ 240 50/60 066795-33 1 2 103 RELAY.
32 Parts List Mod els 358 & 359 DESCRI PT IO N REMARKS WARR. CLASS QTY. 359 QTY. 358 PART NUMBER INSULATOR- SWITCH 1/ 64 ARMITE 029099 2 000 ROD-SW ITCH *350- 1-450- 1* 029135 2 103 SPRING- COMP.
33 Mo del s 358 & 359 Parts List DESCRI PT IO N REMARKS WARR. CLASS QTY. 359 QTY. 358 PART NUMBER WATE R COOLED ACCUMULATOR-COPPER 2" DIA 10" 047062 1 103 ADAPTOR-3/ 8MP X 1/2 BARB- 0110.
Mode l 358 063532-27 Rev. 3/11.
Mode l 358 063532-33 Rev. 3/11.
Mode l 359 065467-33 Rev. 3/11.
Ein wichtiger Punkt beim Kauf des Geräts Taylor thick shake freezers (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Taylor thick shake freezers noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Taylor thick shake freezers - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Taylor thick shake freezers reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Taylor thick shake freezers erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Taylor thick shake freezers besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Taylor thick shake freezers verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Taylor thick shake freezers. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Taylor thick shake freezers gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
