Benutzeranleitung / Produktwartung X9SPU-F des Produzenten SUPER MICRO Computer
Zur Seite of 107
USER’S MANUAL Revision 1.0a X9SPU-F.
Manual Revision 1.0a Release Date: July 23, 2013 Unless you request and receive written permission from Super Micro Computer , Inc., you may not copy any part of this document.
iii Preface Preface This manual is written for system integrators, PC technicians and knowledgeable PC users. It provides information for the installation and use of the X9SPU-F motherboard. About This Motherboard The X9SPU-F Motherboard supports a single Intel® Xeon E3-1200 v2 processor family and Gen-2 Core-i3 (LGA 1 155) processors.
iv X9SPU-F Motherboard User ’s Manual Conventions Used in the Manual: Special attention should be given to the following symbols for proper installation and to prevent damage done to the components .
v Contacting Supermicro Contacting Supermicro Headquarters Address: Super Micro Computer , Inc. 980 Rock Ave. San Jose, CA 95131 U.S.A. T el: +1 (408) 503-8000 Fax: +1 (408) 503-8008 Email: marketing@supermicro.com (General Information) support@supermicro.
vi X9SPU-F Motherboard User ’s Manual T able of Contents Preface About This Motherboard ................................................................................................ iii Manual Organization ........................................
vii T able of Contents Memory Support .............................................................................................. 2-8 Memory Population Guidelines ....................................................................... 2-8 Memory Population Guidelines .
viii X9SPU-F Motherboard User ’s Manual 2-7 Jumper Settings ............................................................................................ 2-26 Explanation of Jumpers ....................................................................
ix T able of Contents 3-5 Returning Merchandise for Service ................................................................. 3-7 Chapter 4 BIOS 4-1 Introduction .........................................................................................
x X9SPU-F Motherboard User ’s Manual C1E ............................................................................................................. 4-7 T urbo Boost T echnology .................................................................
xi WHEA Support ......................................................................................... 4-16 PCH-FW Conguration ............................................................................... 4-16 MDES BIOS Status Code ....
xii X9SPU-F Motherboard User ’s Manual Administrator Password .......................................................................... 4-23 Secure Boot Control ................................................................................. 4-23 Secure Boot Policy .
Chapter 1: Introduction 1-1 Chapter 1 Introduction 1-1 Overview Checklist Congratulations on purchasing your computer motherboard from an acknowledged leader in the industry . Supermicro boards are designed with the utmost attention to detail to provide you with the highest standards in quality and performance.
1-2 X9SPU-F Motherboard User ’s Manual Note : All graphics shown in this manual were based upon the latest PCB Revision available at the time of publishing of the manual. The motherboard you've received may or may not look exactly the same as the graphics shown in this manual.
Chapter 1: Introduction 1-3 Motherboard Layout Important Notes to the User • See Chapter 2 for detailed information on jumpers, I/O ports and JF1 front panel connections. • " " indicates the location of "Pin 1". • Jumpers not indicated are for testing only .
1-4 X9SPU-F Motherboard User ’s Manual MAC C ODE BAR CODE JSD1 1 3 JF1 20 LE5 A C C768 J28 JPW2 R137 RT 1 CO M1 JI2C1 1 JI2C2 1 J29 1 JPME1 JPME2 JL1 7 JLAN2 JLAN1 T- SGPIO1 T- SGPIO2 + SPKR1 J31 J1.
Chapter 1: Introduction 1-5 X9SPU-F Motherboard Headers/Connectors Connector/Switch Description UID-LED Unit ID Switch SBX2 Slot for Supemicro riser card P/N RSC-R1UW-E8R SBX1, SBX3, UIO-RISER Slots for Supermicro riser card T -SGPIO1~T -SGPIO2 Serial Link General Purpose I/O Headers (5V Gen1/Gen 2) I-SA T A0, I-SA T A1 SA T A 3.
1-6 X9SPU-F Motherboard User ’s Manual X9SPU-F Motherboard LED Indicators LED Description Color/State Status LE7 IPMI Heartbeart Green: Blinking IPMI Normal LE4 Standby Power LED Green: Solid On Sta.
Chapter 1: Introduction 1-7 Motherboard Features CPU Single Intel® Xeon E3-1200 v2 processor family and Gen-2 Core-i3 (LGA 1 155) processors. It is also backward compat- ible with Xeon E3-1200 processors. Memory Four (4) UDIMM slots support up to 32GB of DDR3 Unbuf - fered, ECC or non-ECC UDIMM memory , 1333/1600MHz.
1-8 X9SPU-F Motherboard User ’s Manual PC Health Monitoring CPU & Chassis Monitoring Onboard voltage monitors for CPU core, +3.3V , +5V , +/- 12V , +3.
Chapter 1: Introduction 1-9 System Block Diagram Note: This is a general block diagram and may not exactly represent the features on your motherboard. See the Motherboard Features pages for the actual specications of each motherboard. X9SPU-F Motherboard Block Diagram BLOCK DIAGR AM DDR3 (CHA) Intel Xeon E3-1200 v2 E3-1200 Core i3 PCIe3.
1-10 X9SPU-F Motherboard User ’s Manual 1-2 Chipset Overview The I ntel ® C 216 seri es i s a sin gle c hip s olu ti on th at is d esi gne d fo r ded ic ated s er ve rs a nd wo rks ta - tions. It su ppor ts high-speed SAS, SA T A and advanced requiremen ts for Intel Xeon platforms.
Chapter 1: Introduction 1-1 1 1-3 Special Features Recovery from AC Power Loss Basic I/O System (BIOS) provides a setting for you to determine how the system will respond when AC power is lost and then restored to the system.
1-12 X9SPU-F Motherboard User ’s Manual System Resource Alert Thi s feat ure i s availa ble w he n the sy stem i s use d wit h Sup er o Doc to r III i n the W in dow s OS envir onm ent o r use d wit h Sup ero D oc tor I I in Lin ux. S upe ro D oct or is u sed t o noti f y th e use r of ce r ta in sy ste m event s.
Chapter 1: Introduction 1-13 Be sure to connect these connectors to the 24-pin (JPW1) and the 8-pin (JPW2/JPW3) power connectors on the motherboard. Failure in doing so will void the manufacturer warranty on your power supply and motherboard.
1-14 X9SPU-F Motherboard User ’s Manual Notes.
Chapter 2: Installation 2-1 Chapter 2 Installation 2-1 Static-Sensitive Devices Electrostatic-Discharge (ESD) can damage electronic com ponents. T o avoid dam - aging your system board, it is important to handle it very carefully . The following measures are generally sufcient to protect your equipment from ESD.
2-2 X9SPU-F Motherboard User ’s Manual 2-2 Processor and Heatsink Installation W arning : When handling the processor package, avoid placing direct pressure on the label area of the fan. Notes: Always connect the power cord last, and always remove it before adding, removing or changing any hardware components.
Chapter 2: Installation 2-3 2. Gen tly l if t t he lo ad lever t o ope n th e loa d plat e. 3. Use your thumb and your index nger to hold the CPU at the North center edge and the South center edge of the CPU. 4. Align the CPU key that is the semi-circle cutouts against the socket keys.
2-4 X9SPU-F Motherboard User ’s Manual W arning: Y ou can only install the CPU inside the socket only in one direction. Make sure that it is properly inserted into the CPU socket before closing the load plate. If it doesn't close properly , do not force it as it may damage your CPU.
Chapter 2: Installation 2-5 Mounting Holes Motherboard Screw#1 Screw#2 Heatsink Bracket Installing a Passive CPU Heatsink 1. Do not apply any thermal grease to the heatsink or the CPU die -- the re - quired amount has already been applied.
2-6 X9SPU-F Motherboard User ’s Manual Removing the Heatsink W arning: W e do not recommend that the CPU or the heatsink be removed. However , if you do need to uninstall the heatsink, please follow the instruc - tions below to uninstall the heatsink to prevent damage done to the CPU or the CPU socket.
Chapter 2: Installation 2-7 2-3 Installing DDR3 Memory CAUTION Exercise extreme care when installing or removing DIMM modules to prevent any possible damage.
2-8 X9SPU-F Motherboard User ’s Manual MAC C ODE BAR CODE JSD1 1 3 JF1 20 LE5 A C C768 J28 JPW2 R137 RT 1 CO M1 JI2C1 1 JI2C2 1 J29 1 JPME1 JPME2 JL1 7 JLAN2 JLAN1 T- SGPIO1 T- SGPIO2 + SPKR1 J31 J1.
Chapter 2: Installation 2-9 Memory Population Guidelines When installing memory modules, the DIMM slots should be populated in the following order: DIMMA1, DIMMB1 then DIMMA2, DIMMB2 • Always use DDR3 DIMM modules of the same size, type and speed. • Mixed DIMM speeds can be installed.
2-10 X9SPU-F Motherboard User ’s Manual MAC C ODE BAR CODE JSD1 1 3 JF1 20 LE5 A C C768 J28 JPW2 R137 RT 1 CO M1 JI2C1 1 JI2C2 1 J29 1 JPME1 JPME2 JL1 7 JLAN2 JLAN1 T- SGPIO1 T- SGPIO2 + SPKR1 J31 J.
Chapter 2: Installation 2-1 1 Pan head screws (8 pieces) Installing the Motherboard 1. Install the I/O shield into the chassis. 2. Locate the mounting holes on the motherboard. 3. Locate the matching mounting holes on the chassis. Align the mounting holes on the motherboard against the mounting holes on the chassis.
2-12 X9SPU-F Motherboard User ’s Manual MAC C ODE BAR CODE JSD1 1 3 JF1 20 LE5 A C C768 J28 JPW2 R137 RT 1 CO M1 JI2C1 1 JI2C2 1 J29 1 JPME1 JPME2 JL1 7 JLAN2 JLAN1 T- SGPIO1 T- SGPIO2 + SPKR1 J31 J.
Chapter 2: Installation 2-13 MAC C ODE BAR CODE JSD1 1 3 JF1 20 LE5 A C C768 J28 JPW2 R137 RT 1 CO M1 JI2C1 1 JI2C2 1 J29 1 JPME1 JPME2 JL1 7 JLAN2 JLAN1 T- SGPIO1 T- SGPIO2 + SPKR1 J31 J15 C A LE7 LE.
2-14 X9SPU-F Motherboard User ’s Manual Ethernet Ports (LAN1/LAN2) T wo Ethernet ports (LAN1/LAN2) are located next to the VGA port on the I/O backpanel. These ports provide networking connectivity with speeds up to 1Gb/s. Please see the table on the left for the pin denitions.
Chapter 2: Installation 2-15 1. Serial Port (COM1) 2. VGA Port 3, Serial Port Header (COM2) VGA Connector (VGA) A V ideo (VGA/CRT) connector is located next to COM1 Port on the I/O backpanel. This connector is used to provide video and LCD/CRT display .
2-16 X9SPU-F Motherboard User ’s Manual MAC C ODE BAR CODE JSD1 1 3 JF1 20 LE5 A C C768 J28 JPW2 R137 RT 1 CO M1 JI2C1 1 JI2C2 1 J29 1 JPME1 JPME2 JL1 7 JLAN2 JLAN1 T- SGPIO1 T- SGPIO2 + SPKR1 J31 J.
Chapter 2: Installation 2-17 Po we r Butto n Unit ID LED 1 NIC1 LED Re set Butt on 2 Power Fail LED HDD LED Po we r LED #3~4 #1~2 Vcc Vcc Vcc OH/Fan Fail Ground Ground 19 20 Vcc X Ground NMI X Vcc NIC2 LED Front Control Panel Pin Denitions Power LED The Power LED connection is located on pins 15 and 16 of JF1.
2-18 X9SPU-F Motherboard User ’s Manual Po we r Butto n Unit ID LED 1 NIC1 LED Re set Butt on 2 Power Fail LED HDD LED Po we r LED #3~4 #1~2 Vcc Vcc Vcc OH/Fan Fail Ground Ground 19 20 Vcc X Ground .
Chapter 2: Installation 2-19 NMI Button The non-maskable interrupt button header is located on pins 19 and 20 of JF1. Refer to the table on the right for pin denitions. NMI Button Pin Denitions (JF1) Pin# Denition 19 Control 20 Ground Power Button The Power Button connection is locat - ed on pins1 and 2 of JF1.
2-20 X9SPU-F Motherboard User ’s Manual MAC C ODE BAR CODE JSD1 1 3 JF1 20 LE5 A C C768 J28 JPW2 R137 RT 1 CO M1 JI2C1 1 JI2C2 1 J29 1 JPME1 JPME2 JL1 7 JLAN2 JLAN1 T- SGPIO1 T- SGPIO2 + SPKR1 J31 J.
Chapter 2: Installation 2-21 MAC C ODE BAR CODE JSD1 1 3 JF1 20 LE5 A C C768 J28 JPW2 R137 RT 1 CO M1 JI2C1 1 JI2C2 1 J29 1 JPME1 JPME2 JL1 7 JLAN2 JLAN1 T- SGPIO1 T- SGPIO2 + SPKR1 J31 J15 C A LE7 LE.
2-22 X9SPU-F Motherboard User ’s Manual MAC C ODE BAR CODE JSD1 1 3 JF1 20 LE5 A C C768 J28 JPW2 R137 RT 1 CO M1 JI2C1 1 JI2C2 1 J29 1 JPME1 JPME2 JL1 7 JLAN2 JLAN1 T- SGPIO1 T- SGPIO2 + SPKR1 J31 J.
Chapter 2: Installation 2-23 MAC C ODE BAR CODE JSD1 1 3 JF1 20 LE5 A C C768 J28 JPW2 R137 RT 1 CO M1 JI2C1 1 JI2C2 1 J29 1 JPME1 JPME2 JL1 7 JLAN2 JLAN1 T- SGPIO1 T- SGPIO2 + SPKR1 J31 J15 C A LE7 LE.
2-24 X9SPU-F Motherboard User ’s Manual MAC C ODE BAR CODE JSD1 1 3 JF1 20 LE5 A C C768 J28 JPW2 R137 RT 1 CO M1 JI2C1 1 JI2C2 1 J29 1 JPME1 JPME2 JL1 7 JLAN2 JLAN1 T- SGPIO1 T- SGPIO2 + SPKR1 J31 J.
Chapter 2: Installation 2-25 MAC C ODE BAR CODE JSD1 1 3 JF1 20 LE5 A C C768 J28 JPW2 R137 RT 1 CO M1 JI2C1 1 JI2C2 1 J29 1 JPME1 JPME2 JL1 7 JLAN2 JLAN1 T- SGPIO1 T- SGPIO2 + SPKR1 J31 J15 C A LE7 LE.
2-26 X9SPU-F Motherboard User ’s Manual 2-7 Jumper Settings Explanation of Jumpers T o modify the operation of the mother - board, jumpers can be used to choose between optional settings. Jumpers create shorts between two pins to change the function of the connector .
Chapter 2: Installation 2-27 MAC C ODE BAR CODE JSD1 1 3 JF1 20 LE5 A C C768 J28 JPW2 R137 RT 1 CO M1 JI2C1 1 JI2C2 1 J29 1 JPME1 JPME2 JL1 7 JLAN2 JLAN1 T- SGPIO1 T- SGPIO2 + SPKR1 J31 J15 C A LE7 LE.
2-28 X9SPU-F Motherboard User ’s Manual MAC C ODE BAR CODE JSD1 1 3 JF1 20 LE5 A C C768 J28 JPW2 R137 RT 1 CO M1 JI2C1 1 JI2C2 1 J29 1 JPME1 JPME2 JL1 7 JLAN2 JLAN1 T- SGPIO1 T- SGPIO2 + SPKR1 J31 J.
Chapter 2: Installation 2-29 BMC Enable/Disable (JPB) JPB is used to enable or disable the BMC (Baseboard Management Control) chip and the onboard IPMI port. This jumper is used together with the IPMI settings in the BIOS. See the table on the right for the jumper settings.
2-30 X9SPU-F Motherboard User ’s Manual ME Recovery (JPME1) ME Recovery (JPME1) is used to en - able or disable the ME Recovery fea - ture of the motherboard.
Chapter 2: Installation 2-31 LAN Port LEDs The LAN ports are located on the I/O backpanel of the motherboard. Each Ethernet LAN port has two LEDs. The ye llo w LED in dic ate s ac ti vit y, whi le the Link L ED m ay b e gr een , amb er , or of f to in dic ate t he sp ee d of the conn ec ti ons .
2-32 X9SPU-F Motherboard User ’s Manual MAC C ODE BAR CODE JSD1 1 3 JF1 20 LE5 A C C768 J28 JPW2 R137 RT 1 CO M1 JI2C1 1 JI2C2 1 J29 1 JPME1 JPME2 JL1 7 JLAN2 JLAN1 T- SGPIO1 T- SGPIO2 + SPKR1 J31 J.
Chapter 2: Installation 2-33 2-9 SA T A Connections SA T A Connections (I-SA T A0~5) Six Serial A T A (SA T A) connectors (I-SA T A 0~5) are located on the moth - erboard. I-SA T A 0/1 supports data transfer rates of up to 6Gb/s (SA T A 3.0), while I-SA T A 2~5 supports data transfer rates of up to 3Gb/s (SA T A 2.
2-34 X9SPU-F Motherboard User ’s Manual MAC C ODE BAR CODE JSD1 1 3 JF1 20 LE5 A C C768 J28 JPW2 R137 RT 1 CO M1 JI2C1 1 JI2C2 1 J29 1 JPME1 JPME2 JL1 7 JLAN2 JLAN1 T- SGPIO1 T- SGPIO2 + SPKR1 J31 J.
3-1 Chapter 3: Troubleshooting Chapter 3 T roubleshooting 3-1 T roubleshooting Procedures Use t he fo llow in g pro c edur es to t ro ubl esh oot yo ur syste m.
3-2 X9SPU-F Motherboard User ’s Manual No Video 1. If the power is on, but you have no video--in this case, you will need to re - move all the add-on cards and cables rst. 2. Use the speaker to determine if any beep codes exist. (Refer to Appendix A for details on beep codes.
3-3 Chapter 3: Troubleshooting 3-2 T echnical Support Procedures Before contacting T echnical Support, please make sure that you have followed all the steps listed below .
3-4 X9SPU-F Motherboard User ’s Manual 3-3 Frequently Asked Questions Question: What type of memory does my motherboard support? Answer: Please see Section 2-3 for a comprehensive answer . Question: How do I update my BIOS? Answer: It is recommended that you do not upgrade your BIOS if you are not experiencing any problems with your system.
3-5 Chapter 3: Troubleshooting Question: Why do I get an error message “IASTOR.SYS read error” and "press F6 to install Intel RAID driver" when installing Windows on my motherboard? Answer: T o solve this issue, disable the IPMI jumper (if your motherboard has this feature).
3-6 X9SPU-F Motherboard User ’s Manual Proper Battery Disposal W arning! Please handle used batteries carefully . Do not damage the battery in any way; a damaged battery may release hazard - ous materials into the environment. Do not discard a used battery in the garbage or a public landll.
3-7 Chapter 3: Troubleshooting 3-5 Returning Merchandise for Service A rec ei pt or c opy of yo ur invoi ce m ar ked wi th t he date o f purc ha se is re qui red befo re any war r ant y se r v ic e wi ll be r end ere d. Y ou ca n obt ain s er v ic e by c alli ng your ven do r for a Ret ur ned M er ch and ise Au th or iz ati on (R M A) numb er .
3-8 X9SPU-F Motherboard User ’s Manual Notes.
Chapter 4: AMI BIOS 4-1 Chapter 4 BIOS 4-1 Introduction This chapter describes the AMI BIOS Setup Utility for the X9SPU-F Motherboard . The AMI ROM BIOS is stored in a Flash EEPROM and can be easily updated. This chapter describes the basic navigation of the AMI BIOS Setup Utility setup screens.
4-2 X9SPU-F Motherboard User ’s Manual How to Start the Setup Utility Normally , the only visible Power-On Self-T est (POST) routine is the memory test. As the memory is being tested, press the <Delete> key to enter the main menu of the AMI BIOS Setup Utility .
Chapter 4: AMI BIOS 4-3 System Overview: The following BIOS information will be dis played: System Time/System Date Use this option to change the system time and date. Highlight System Time or Sys - tem Date using the arrow keys. Enter new values through the keyboard.
4-4 X9SPU-F Motherboard User ’s Manual 4-3 Advanced Setup Congurations Use the arrow keys to select Boot Setup and hit <Enter> to access the submenu items. BOOT Feature Quiet Boot This option allows the bootup screen options to be modied between POST mes - sages or the OEM logo.
Chapter 4: AMI BIOS 4-5 W ait For 'F1' If Error Thi s for ce s th e syste m to wait u ntil t he ' F1 ' key is pre ss ed i f an er ro r oc c ur s. Th e opti on s are D is abl ed an d Enabled . Interrupt 19 Capture Interrupt 19 is the software interrupt that handles the boot disk function.
4-6 X9SPU-F Motherboard User ’s Manual CPU Conguration This item is for informational purposes only and displays CPU conguration informa - tion including type, frequency , data cache, etc.
Chapter 4: AMI BIOS 4-7 Active Processor Cores Set to Enabled to use a processor's Second Core and beyond. (Please refer to Intel's web site for more information.) The options are All, 1, 2, 3. Power T echnology This feature determines what power-saving scheme the motherboard uses.
4-8 X9SPU-F Motherboard User ’s Manual Chipset Conguration W ARNING: Setting the wrong values in the following sections may cause the system to malfunction. CPU Bridge Conguration This item displays the current processor conguration, including the frequency and memory type.
Chapter 4: AMI BIOS 4-9 South Bridge Conguration This item displays the current South Bridge Revision. USB Functions This feature allows the user to decide the number of onboard USB ports to be enabled. The Options are: Disabled and Enabled . USB 3.
4-10 X9SPU-F Motherboard User ’s Manual AHCI Mode The following items are displayed when AHCI Mode is selected: Aggressive Link Power Management This feature Enables or Disables Aggressive Link Power Management support for Cougar Point B0 stepping and later .
Chapter 4: AMI BIOS 4-1 1 Load Onboard LAN1 Option ROM / Load Onboard LAN2 Option ROM This feature is to enable or disable the onboard option ROMs. The default for LAN 1 is Enabled .
4-12 X9SPU-F Motherboard User ’s Manual Serial Port Console Redirection These submenus allow the user to congure Console Redirection settings. COM 1, COM2, SOL Console Redirection Select Enabled to use a COM Port selected by the user for Console Redirection.
Chapter 4: AMI BIOS 4-13 Stop Bits A stop bit indicates the end of a serial data packet. Select 1 Stop Bit for standard serial data communication. Select 2 Stop Bits if slower devices are used.
4-14 X9SPU-F Motherboard User ’s Manual Console Redirection Settings (for EMS) This feature allows the user to specify how the host computer will exchange data with the client computer , which is the remote computer used by the user . Out-of-Band-Mgmt Port Use this feature to select the port for out-of-band management.
Chapter 4: AMI BIOS 4-15 CPU T emperature The CPU temperature status displays as follows: Low – This level is considered as the ‘normal’ operating state. The CPU temperature is well below the CPU ‘T emperature T olerance’. The mother - board fans and CPU will run normally as congured in the BIOS (Fan Speed Control).
4-16 X9SPU-F Motherboard User ’s Manual pendency on other timestamp calculation devices, such as an x86 RDTSC Instruc - tion embedded in the CPU. The High Performance Event Timer is used to replace the 8254 Programmable Interval Timer. The options are Enabled and Disabled.
Chapter 4: AMI BIOS 4-17 Lock ICC registers When set to All registers, all ICC registers will be locked. When set to Static only , only static ICC registers will be locked.
4-18 X9SPU-F Motherboard User ’s Manual Log System Boot Event This option toggles the System Boot Event logging to enabled or disabled. The options are Disabled and Enabled. MECI The Multiple Event Count Increment (MECI) counter counts the number of times a duplicate event must happen before the MECI counter is incremented.
Chapter 4: AMI BIOS 4-19 4-5 IPMI Settings Intelligent Platform Management Interface (IPMI) is a set of common interfaces that IT administrators can use to monitor system health and to manage the system as a whole. For more information on the IPMI specications, please visit Intel's website at www .
4-20 X9SPU-F Motherboard User ’s Manual BMC Network Conguration Set this feature to congure the IPMI LAN adapter with a network address. Update IPMI LAN Conguration This feature allows the user to decide if the BIOS should congure the IPMI setting at next system boot.
Chapter 4: AMI BIOS 4-21 4-6 Boot Settings Use th is feat ure to c on gu re Bo ot Set ti ngs . Setup Prompt Timeout Use this feature to enter the number of seconds to wait for setup activation key . The default setting is 1 second. Retry Boot Devices When set to Enabled, the BIOS will continuously retry to boot from a legacy device.
4-22 X9SPU-F Motherboard User ’s Manual Boot Options Priorities This feature allows the user to specify which devices are boot devices and the order of priority from which the systems boots during startup. Boot Option #1, Boot option #2, etc. The settings are [ any detected boot device ] and Disabled.
Chapter 4: AMI BIOS 4-23 • If the Administrator password is dened ONL Y - this controls access to the BIOS setup ONL Y . • If the User's password is dened ONL Y - this password will need to be entered during each system startup or boot, and will also have Administrator rights in the setup.
4-24 X9SPU-F Motherboard User ’s Manual Secure Boot Policy Use this feature to congure the extended options for Secure Boot mode. Internal FV Use this item to determine whether or not to load an image from the above device path in the event of a security violation.
Chapter 4: AMI BIOS 4-25 Delete the DB : Deletes the Authorized Signature Database. Append an entry to DB : This item launches the Filebrowser to append the Autho - rized Signature Database entry from le.
4-26 X9SPU-F Motherboard User ’s Manual 4-9 Save & Exit Select the Exit tab from the BIOS Setup Utility screen to enter the Exit BIOS Setup screen. Discard Changes and Exit Select this option to quit the BIOS Setup without making any permanent changes to the system conguration, and reboot the computer .
Chapter 4: AMI BIOS 4-27 Restore Defaults T o set this feature, select Restore Defaults from the Exit menu and press <Enter>. These are factory settings designed for maximum system stability , but not for maximum performance.
4-28 X9SPU-F Motherboard User ’s Manual Notes.
Appendix A: POST Error Beep Codes A-1 Appendix A BIOS Error Beep Codes During the POST (Power-On Self-T est) routines, which are performed each time the system is powered on, errors may occur . Non-fatal errors are those which, in most cases, allow the system to continue with bootup.
A-2 X9SPU-F Motherboard User ’s Manual Notes.
Appendix B: Software Installation Instructions B-1 Driver/T ool Installation Display Screen Note 1 . Click the icons showing a hand writing on the paper to view the readme les for each item. Click on a computer icon to the right of an item to install this item (from top to the bottom), one at a time.
B-2 X9SPU-F Motherboard User ’s Manual SuperDoctor III Interface Display Screen-I (Health Information) B-2 Conguring SuperDoctor ® III The SuperDoctor III program is a Web-based management tool that supports remote management capability . It includes Remote and Local Management tools.
Appendix B: Software Installation Instructions B-3 Note : T he S upe rD oc to r III sof t ware a nd m anua l may b e do wnl oad ed f ro m ou r Website at: http:/ /w w w .
B-4 X9SPU-F Motherboard User ’s Manual Notes.
UEFI BIOS Recovery C-1 Appendix C UEFI BIOS Recovery Instructions W arning! Do not upgrade the BIOS unless your system has a BIOS-related issue. Flashing the wrong BIOS can cause irreparable damage to the system. In no event shall Supermicro be liable for direct, indirect, special, incidental, or consequential damages arising from a BIOS update.
C-2 X9SPU-F Motherboard User ’s Manual Note : At this point, you may decide if you want to start with BIOS Recov - ery . If you decide to proceed with BIOS Recovery , follow the procedures below . a USB CD/DVD ROM/RW device can be used for this purpose.
UEFI BIOS Recovery C-3 5. When the screen as shown above displays, using the arrow key , select the item- "Proceed with ash update" and press the <Enter> key . Y ou will see the progress of BIOS Recovery as shown in the screen below .
C-4 X9SPU-F Motherboard User ’s Manual 8. When a DOS prompt appears, type AMI.BA T BIOSname.### at the prompt. Note: Do not interrupt this process until BIOS ashing is completed. 9. After seeing the message that BIOS update is completed, unplug the AC power cable to clear CMOS, and then plug in the AC power cable to power on the system.
(Disclaimer Continued) The products sold by Supermicro are not intended for and will not be used in life support systems, medical equipment, nuclear facilities or systems, aircraft, aircraft devices, .
Ein wichtiger Punkt beim Kauf des Geräts SUPER MICRO Computer X9SPU-F (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie SUPER MICRO Computer X9SPU-F noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für SUPER MICRO Computer X9SPU-F - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von SUPER MICRO Computer X9SPU-F reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über SUPER MICRO Computer X9SPU-F erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon SUPER MICRO Computer X9SPU-F besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von SUPER MICRO Computer X9SPU-F verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit SUPER MICRO Computer X9SPU-F. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei SUPER MICRO Computer X9SPU-F gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
