Benutzeranleitung / Produktwartung NX-2415 des Produzenten Star Micronics
Zur Seite of 134
USERS MANUAL NOT INTENDED FOR SALE.
Federal Communications Commission Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part IS of FCC Rules. These limits are designed to provide reasonable protection against harmful Interference m a residential installation.
b c. L. c L b. HOW TO USE THIS MANUAL This manual is organized into nine chapters. To learn how to make the best use of your printer you are urged to read through chapters 1 through 3. The remaining chapters may be treated as a reference guide for programming operations, etc.
Chapter 6 - MS-DOS and your printer Since the PC or PC-AT family of computers running under MS-DOS is currently the most popular configuration of microcomputer, we have in- cluded a few hints and tips to help you use your printer with such systems.
FEATURES OF THE PRINTER This printer is a convenient, monochrome printer without frills but with a full complement of features, making it an excellent partner for a personal computer. It supports the IBM/Epson printer commands and character sets, enabling it to print just about anything your computer can generate, both text and graphics.
TABLE OF CONTENTS Chapter 1 SETTING UP THE PRINTER .............................................. .1 Locating the Printer .......................................................................... 1 Unpacking and Inspection ...........................
Chapter 3 DIP SWITCH SETTINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Location of the DIP Switches.. ...................................................... .3 1 Functions of the DIP Switches .
Chapter 8 SPECIFICATIONS ................................................................ 107 Chapter 9 CHARACTER SETS ............................................................. 111 Standard Character Set ...........................................
L i Chapter 1 SETTING UP THE PRINTER Subjects covered in Chapter 1 include - l Locating the printer l Unpacking and inspection (names of parts) l Setting up and connection l Loading single sheets l Lo.
UNPACKING AND INSPECTION Check the carton contents Now unpack the contents of the printer shipping carton, and check each item in the box against Figure 1- 1 to make sure that you have everything (there should be five items). If any of these items are missing, contact your supplier.
The optional accessories which you may have ordered with your printer are: 9 Serial (RS-232) interface board l Automatic sheet feeder l Pull tractor unit l Font card l RAM card Parts name of the printer Make an external inspection of the printer. Note the locations of the follow- ing parts: Power Entry slot Release lever Figure 1-Z.
-- SElTlNG UP Place the printer inthe position where it is going to be permanently sited, and remove all packing material from inside the top cover. This packing material is intended to prevent damage to the printer in transit.
1. Use the tensioning knob on the ribbon cartridge to tighten the ribbon if it is slack (turn clockwise). 2. Use the grips on the side of the ribbon cartridge to help locate the cartridge (squeeze them inwards gently), and make sure that the spindles on the cartridge holder fit into the sockets on the cartridge itself.
3. The ribbon should pass between the print head and the print head shield (see Figure l-6). -. -- - - Figure I-6. Pass the ribbon between the print head and print head shield Now, hold the top cover upright and engage the tabs at the back. Then swing the front edge down until the cover is closed.
Ins tall the optional IC card This printer has five built-in character styles (fonts), and an1 1 K-byte data buffer. You can add more fonts or expand the data buffer by installing oprional IC cards (Font card or RAM card). To install or change an IC card, first turn off the power switch.
Connection Connect the printer to your computer, using a standard parallel-type cable. On a PC or PC/AT-type computer, this means that you use the 25way D- type connector at the computer end, and the Amphenol-type 36-way connector at the printer end.
Figure I-9. Replacing the interface board 9.
LOADING SINGLE SHEETS This section will take you through the procedures for loading single sheets of paper. If you are using the optional automatic sheet feeder (ASF), read the ASF instruction booklet. Automatic loading I / Single sheets can be loaded manually with power off, or automatically with power on.
3. Adjust the paper guides to match the size of paper you will be using (re- membering that printing will start some distance from the left-hand edge of the carriage). 4. Place a single sheet between the guides, placing the side on which you want to print towards the back of the printer.
Manual loading It is also possible to load papermanually while the printer’s power is off. The procedure is: 1. Place the paper guide in position, locating the lugs on the bottom of the assembly into the slots on the rear cover of the printer. 2. Check that printer power is off and the release lever at the back of the printer is down.
LOADING AND PARKING FANFOLD FORMS Fanfold forms have holes along the sides and perforations between the sheets. They are also called sprocket forms, punched forms, or just plain “computer paper”. This printer accepts forms up to 16” wide. Fanfold forms are loaded, parked, and unparked as explained next.
6. With the sprocket covers open, thread the paper over the sprockets, aligning holes with the pins on the sprockets. 7. Adjust the spacing of the sprockets by sliding them along the bar, using the cl.
12. Mount the paper guide in the horizontal position shown in Figure 1-14, so that it will separate the printed from the unprinted paper. Figure l-74. Mounting the paper guide for fanfold forms Loading the paper with pull tractor unit You can load the fanfold paper by using the optional pull tractor unit.
Platen roller sha Pull tractor unit ‘pure 7-75. Mounting the optional pull tractor unit -- . . rguro 7-m. I mead the tantold paper over the sprockets trom the entry slot of the printer -. 7. Now close the sprocket covers, again making sure that the paper sprocket holes are aligned with the pins on the sprockets.
i L.. L I b. I i. L. L L L t L Paper parking After loading fanfold paper with the internal tractor unit, you do not have to unload it when you want to print on a single sheet. The printer will “park” it for you if you follow the procedure below. 1.
ADJUSTING THE PRINTING GAP The distance between the print head and the platen can be adjusted to accommodate different paper thicknesses. To make this adjustment, remove the top cover. The adjustment lever is located near the right end of the paper bail.
Chapter 2 CONTROL PANEL OPERATIONS The control panel buttons can be pressed singly to perform the operations indicated by their names. Other functions can be obtained by holding these buttons down when you turn the printer’s power on. Still further functions can be executed by pressing the control panel buttons in combination.
ON LINE button The ( ON LINE ) button sets the printer on-line and off-line. The state changes each time you press the button. In the on-line state the printer receives data from the computer and prints the data. In the off-line state the printer stops printing and sends the computer a signal indicating that it cannot accept data.
L PAPER FEED button If you press this button in off-line, the paper feeds forward. If you hold this button down, the printer performs consecutive line feeds. While you are feeding lines, if you also press the ( ON LINE > button, the paper will feed to the top of the next page.
STYLE button This button selects the font style to be printed. Courier style is always selected at power-up. To change to one of the other styles, set the printer off- line, then press the (STYLE) button repeatedly until the indicators beside the desired selection illuminate.
POWER-UP FUNCTIONS In addition to their normal functions, all the control panel buttons have special functions that operate if you hold them down while switching power on.
Long test mode If the printer is turned on while the (PAPER FEED) button is pressed, the printer will enter the long self-test mode. The printer will start printing as soon as the (PAPER FEED) button .
Stay in panel style If held down during power-up, the (STYLE) button prevents software inter- ference with the font style selected from the control panel. There will be an acknowledging beep, after which you can set the printer off-line, select a font style, then return to the on-line state and start printing.
The following BASIC program is a simple test you can run in hexadecimal mode: 10 FOR I=0 TO 255 20 LPRINT CHR$(I); 30 NEXT I 40 LPRINT 50 END If your system passes the codes directly to the printer without changing them, you will get a printout like Figure 2-4.
When the IBM-PC BASIC interpreter sends hex code OD (carriage return) it adds an extra hex OA (line feed). Hex code 1A (end-of-file) also gets special treatment: the interpreter does not send it at ah. This can cause problems that generate graphics or download character data, but there is a solution.
SWITCH COMBINATION FUNCTIONS Several additional functions can be obtained by pressing the control panel buttons in combinations. Top of form Clearing the buffer F/guru Z-6. Switch combination functions of control panel Form feed If you are using single sheets, this operation ejects the current page.
Top of form When you turn on printer power, the top-of-form position is automatically set to the current position. If this is not where you want the top of the page to be, you can change the top-of-form position as follows. 1. Press the ( ON LINE > button to set the printer off-line.
Clearing the buffer When DIP switch 2-l is ON, the printer stores received data in a large memory buffer. This creates a problem when you want to abandon a printing job and restart: the printer may be holding much more data in its buffer than it has actually printed, and this unprinted data must be cleared out before restarting.
. L . Chapter 3 DIP SWITCH SETTINGS The bank of DIP (Dual In-line Package) switches inside the printer is used for various functions. This chapter explains where the DIP switches are located, and how to use them.
FUNCTIONS OF THE DIP SWITCHES The printer is delivered with all DIP switch set to the ON position. These am the standard settings. By changing the settings, you can alter various printer functions to match your requirements. The following questions will help you make the right settings.
Switch 1-3: Do you want a bottom margin? Leave this switch ON if you do not want to set the bottom margin. Move it to the OFF position if you want to set the bottom margin to the l-inch. Switch 1-4: Are you going to use the automatic sheet feeder (ASF)? To use the automatic sheet feeder, move this switch to the OFF position.
Switch 1-8: Do you want an automatic line feed? If you leave this switch at the ON position, a separate line-feed code is required to obtain a line feed, If you move this switch to the OFF position, the printer performs both a carriage return and line feed each time it receives a carriage-return code.
-. . . L b_ c . c a. L. L.. Switch 2-8: Which type of printing area format do you want to use for single sheets? This printer can use two types of printing area format for single sheets.
. MEMO 4 -.
chapter 4 PRINTER CONTROL COMMANDS L L L i i L L i. : The printer has two emulation modes: Standard mode and IBM mode. In standard mode, the printer emulates the functions of the Epson LQ-1050. In IBM mode, the printer emulates the IBM Proprinter XL24.
- Many commands have alternative forms. Some commands use <ESC> (character code 27) in Standard mode and cFS> (character code 28) in IBM mode. Other commands have parameters that can be specified as either character codes or digit characters, like the parameter 1 in the sample command above.
Select Courier characters n Font style 0 Courier (initial value) 1 Optional font 2 Prestige 3 Orator 4 script Mode ASCII Decimal Hexadecimal Both 'I(“ 'I(,‘ “F" ‘I)" “),' "0" 40 40 70 41 41 48 28 28 46 29 29 30 Changes to the Courier font.
Select Script characters Mode ASCII Decimal Hexadecimal Both “(4‘ “(“ ‘SF’ “)” ,,),, “4” 40 40 70 41 41 52 28 20 46 29 29 34 Changes to the Script font. Ignored if the (STYLE) button was pressed during power-up. Select italic characters - Mode ASCII Decimal Hexadecimal Both “(” “(” “I” ‘6)” s.
Emphasized printing Mode ASCII Decimal Hexadecimal Both <ESC> “E” 27 69 16 45 Causes subsequent characters to be emphasized by adding extra thickness to vertical strokes. Cancel emphasized printing Mode ASCII Decimal Hexadecimal Both &SC> “F’ 27 70 IB 46 Cancels emphasized printing.
Stop underlining Mode ASCII Decimal Hexadecimal II ( ‘6 l . ( ‘I “_” “),, ‘,),, "0" 40 40 45 41 41 48 28 28 2D 29 29 30 Both <ESC> “-” “0” 27 45 48 1B 2D 30 <ESC> I’-” <o> 27 45 0 1B 2D 00 Stops underlining.
Cancel superscript or subscript Mode ASCII Decimal Hexadecimal Both <ESC> “T” 27 84 1B 54 Stops printing superscripts or subscripts and returns to normal printing. CHARACTER SET COMMANDS Select standard character set Selects the standard character set.
Select character set #2 Mode ASCII Decimal Hexadecimal Both <ES& “6” 27 54 1B 36 Selects character set #2. Select international character set - Mode ASCII Decimal Hexadecimal Std. <ES& “R” n 27 82 n 1B 52 n IBM cFS> “R” n 28 82 n 1C 52 n -, - Selects an international character set according to the value of n.
‘ Enable printing of all character codes on next character Mode ASCII Decimal Hexadecimal IBM <ESC> “ h ” 27 94 1B 5E This command operates like <ESC> ‘Y” except that it remains in effect for only one character. Select slash zero Mode ASCII Decimal Hexadecimal <ESC> “ “ e.
Elite pitch Mode ASCII Decimal Hexadecimal Both <ESC> “M” 27 77 18 4D IBM <ESC> “:” 27 58 1B 3A In Standard mode, changes from either pica or semi-condensed to elite pitch (12 cpi) or from condensed pica to condensed elite (20 cpi).
Condensed printing Mode ASCII Decimal Hexadecimal Both <Sb 15 OF cESC> <Sb 27 15 1B OF In Standard mode, changes from pica to condensed pica (17 cpi) or from elite to condensed elite (20 cpi). In IBM mode, changes from either pica or elite to condensed (17 cpi).
. . Expanded printing for one line Mode ASCII Decimal Hexadecimal Both <so> 14 OE <ESC> <SO> 27 14 1B OE Causes subsequent characters in the current line to be expanded to double width. Characters return to normal width after the next line feed (<LF>).
Select fixed spacing Mode ASCII Decimal Hexadecimal Both cESC> “p” “0’ 27 112 48 1B 70 XI <ESC> “p” <O> 27 112 0 1B 70 00 IBM <ESC> “P” <0> 27 80 0 1B 50 00 Causes subsequent characters to be printed with fixed character spacing.
Select double or quadruple size Mode ASCII Decimal Hexadecimal Both <ESC> “h” n 27 104 n 1B 88 n Selects the size of subsequent characters as shown below. Extra- high characters align along the cap-line of normal characters, with the base line temporarily moving down.
Return to normal height ~1 Terminates double-height printing and prints subsequent characters at normal height. Select character height, width, and line spacing Mode ASCII Decimal Hexadecimal Both <.
Select character type and print pitch Mode ASCII Decimal Hexadecimal IBM cESC> “I” n 27 73 n 1B 49 n Selects a combination of character type and print pitch according to the value of n as shown below.
VERTICAL POSITION COMMANDS Set line spacing to l/6 inch Mode ASCII Decimal Both <ESC> “0” 27 48 1B 30 Sets the distance the paper advances or reverses in subsequent line feeds to l/8 inch.
Set base unit for line spacing Mode ASCII Decimal Hexadecimal IBM <ESC> “[‘I ‘T’ <4> <0> 279192 4 0 lB585CO400 co> <o> n CO> 0 On0 00 WnW Sets the base unit for the line spacing commands, cESC> “3” and <ES0 “J”.
L, L Execute <ES& ‘A” Mode ASCII Decimal Hexadecimal IBM cEsc> “T’ 27 50 1B 32 Sets the line spacing to the value defined by the last preceding <ESC> “A” command. Sets the line spacing to l/6 inch if there is no preceding <ESC> “A” command.
Perform one n/l 80-inch or n/216-inch line feed Mode ASCII Decimal Hexadecimal Both <ES6 “I-’ n 27 74 n 1B 4A n Feeds the paper once by n/l 80 inches (standard mode) or n/216 inches, where n is between 1 and 255. Does not move the print position right or left when DIP switch l-2 is OFF.
. . . L.. i L Set page length to n lines Mode ASCII Decimal Hexadecimal Both <ESC> “C” n 27 67 n 1B 43 n Sets the page length to n lines in the current line spacing, where n is between 1 and 127 in Standard mode or between 1 and 255 in IBM mode.
Cancel top and bottom margins Mode ASCII Decimal Hexadecimal Both <ESC> “0” 27 79 1B 4F Cancels both the top margin and the bottom margin. Form feed Mode ASCII Decimal Hexadecimal Both <FF> 12 oc Feeds the paper to the top of the next page according to the current _ page length, and moves the print position to the left margin.
Set vertical tab stops Mode ASCII Decimal Hexadecimal Both <ESC> “B” nl n.2 . . . <O> 27 66 nI n2 . . . 0 1B 42 nl n2 . . . 00 Cancels all current vertical tab stops and sets new vertical tab stops at lines nl, n2, etc., where nl, n2, etc.
Vertical tab IMode 1 ASCII 1 Decimal 1 Hexadecimal I I I I Both 1 <VT> 11 OB Feeds the paper to the next vertical tab stop and moves the print position to the left margin.
Set right margin Mode ASCII Decimal Hexadecimal Std. <ESC> “Q” n 27 01 n 1B 51 n IBM <FS> “C?’ n 20 01 n 1C 51 n Sets the right margin at column n in the current character pitch (pica pitch if proportional spacing is currently selected).
Set automatic line feed Mode ASCII Decimal Hexadecimal IBM <ESC> “5” <1> 27 53 1 18 35 01 Causes the printer to perform both a carriage return and line feed each time it receives a <CR> code. This command takes priority over DIP switch l-8.
L... L L. L L 4.. * i i i. i Right justify Mode ASCII Decimal Hexadecimal Both <ESC> “a” “2” 27 97 50 1B 61 32 cESC> “a” c2> 27 97 2 1B 61 02 Aligns subsequent text with the right margin, leaving the left margin ragged.
Reset all tab stops Mode ASCII Decimal Hexadecimal IBM cESC> “R” 27 02 18 52 Resets the horizontal tab stops to their power-up values in which a tab stop is set every 8 column starting at column 9.
Absolute horizontal tab in inches Mode ASCII Decimal Hexadecimal Both <ESC> “$” nl n2 27 36 nl n2 1B 24 nl n2 Sets the next print position to (nl + n2 x 256)/60 inches from the left margin on the current line. Ignored if this position is beyond the right margin.
Print g-bit double-density, double-speed graphics Mode ASCII Decimal Hexadecimal Both cESC> “I”’ nl n2 27 09 nl n2 1B 59 nl n2 ml m2 . . . ml m2 . . . ml m2 . . . Prints bit-image graphics at 120 dots per inch horizontally (maxi- mum 1632 dots wide), skipping every second dot in the horizontal direction.
Select graphics mode Mode ASCII Decimal Hexadecimal Both cESC> “*” FIO nl 27 42 n0 nl 1B 2A n0 nl n2 ml m2 . . . n2 ml m2 . . . n2 ml m2 . . . Selects one of eleven graphics modes depending on the value of nO and prints dot graphics in this mode.
- Select graphics mode Mode ASCII Decimal Hexadecimal IBM cESC> “1” “g” nl d 27 91 103 nl n2 1 B 58 67 nl n2 m0 ml m.2 . . . m0 ml m2... m0 ml m2... Selects one of eight graphics modes depending on the value of m0 and prints dot graphics in this mode.
L L L. I.. i L L L : i DOWNLOAD CHARACTER COMMANDS Define download characters Mode ASCII Decimal Hexadecimal <ES0 “&I CO> nl 27 30 0 nl 1B 26 00 nl Std. n2 m0 ml m2 n2mOmlm.2 n2mOmlm.2 dl d2 . . . & dl d2 . . . dx dl d2 . . . ah cESC> ‘I=” CO> nl 27 61 0 nl 1B 3D 00 nl IBM n2 m0 ml m.
._. Copy character set from ROM into RAM card Mode ASCII Decimal Hexadecimal Std. <ESC> “:” <0> n <o> 27 58 0 R 0 1B 3A 00 n 00 IBM <FS> Y’ <o> n <o> 28 58 0 .
OTHER PRINTER CONTROL COMMANDS Set MSB to 1 Mode ASCII Decimal Hexadecimal Both <ESC> “7” 27 62 1B 3E Sets the most significant bit of each subsequent byte received to 1, allowing users with a 7-bit interface to access characters with ASCII codes greater than 127.
Repeat data Mode ASCII Decimal Hexadecimal <ESC7 “V” n dl 27 86 n dl IB 56 n dl Both d2 di <ESC> d2 . . . dx 27 d2 ah IB “V” <o> 86 0 5600 Repeats data, defined by dl, d2, .
I . . Cancel immediate print . . L. i r L. Mode ASCII Decimal Hexadecimal Both <ESC> “i” “0” 27 105 48 1B 69 30 <ESC> “i” <o> 27 105 0 IB 69 00 Cancels the immediate print mode. The printer waits for each line to be completed before printing it, and does not scroll the paper up and down.
Bell IMode 1 ASCII 1 Decimal 1 Hexadecimal I 1 Both I cBEL> I 7 I 07 I Sounds a brief beep tone from the printer’s beeper. Bidirectional printing Mode ASCII Decimal Hexadecimal Both <ESC> .
Auto feed Mode ASCII Decimal Hexadecimal Bo* <ESC> <EM> c47 27 25 4 1B 19 04 “(” “(” "4" ")" ")" 40 40 52 41 41 28 28 34 29 29 Selects the automatic sheet feeder. Ignored if DIP switch l-4 is ON (ASF inactive).
MEMO.
Chapter 5 DOWNLOAD CHARACTERS With this printer you can create new characters and symbols, download their dot data, and have them printed in place of selected characters in the regular character set. Characters that can be generated in this way range from simple but useful symbols like the check mark through complex Chinese or Japanese characters.
We will use a tiny representation of a telephone symbol for our example. ASCII Code: 60 Left space: 4 Character width: Right space: 3 29 Now, we calculate the vertical numerical values of the columns of dots, and enter them underneath the grid.
L.. L b.. t . Assigning a value of character space Besides being able to specify the actual width of the character, this printer allows you to specify the position in the standard grid where the character will print. You must specify the dot column in which the printed character starts and the dot column in which the character ends.
1000 LPRINT CHR$(27);"xl"; 1010 LPRINT CHR$(27); "&";CHR$(O);CHR$(60):CHR$(61); 1020 RESTORE 1540 1030 FOR N=60 TO 61 1040 READ LS :LPRINT CHR$(LS); 1050 READ CW :LPRINT CHR$(C.
1600 DATA 80,175,192, 1610 DATA 1620 1 Cai 40, 0, 0. Symbol 1630 DATA 4. 29, 3 1640 DATA 0, 30, 0, 1650 DATA 0, 3, 64, 1660 DATA 20,124, 0, 1670 DATA 63,128, 0, 1680 DATA 64,124,128, 1690 DATA 51, 3, 0, 32, SO, 0, so, 47,192, 40, 16, 0. 19, 15,192 23, 0, 0, 8, 0, 0, 7, 0, 0 0, 0, 0, 0, 60, 0.
MEMO -- ..- -..
Chapter 6 MS-DOS AND YOUR PRINTER When using your printer with an IBM PC, PC-XT, or PC-AT or compatible, you will probably be using PC-DOS or MS-DOS as an operating system. A number of software tricks may be useful here. This chapter is not, however, a substitute for the operating system manuals supplied with your computer.
Number of columns CPI Pica 10 136 Elite 12 163 Condensed pica 17.1 233 Condensed elite 20 272 Proportional Variable Sometimes the software installation will ask you for an initialization sequence to return to the default settings. The command for your printer is <ESC> @.
If you want to print a title in double-size Script, then change to regular-size Courier for some text that includes italics, you can use these commands as follows: File as seen on computer screen: ((F.
The printer supports various commands in addition to the above, such as quadruple-size printing. Most of these other commands consist of the escape code followed by one or more letters or numbers.
COPY and TYPE do not permit you to execute other commands while the file is printing. If you want a particular font style, or print pitch, you can make these settings from the control panel before you start printing. See Chapter 2. c. If you print from the DOS command level very often, it will be advantageous to create a printer setup file.
“V indicates that the following character is a control code. “V[ enters the cESC> code. <ESC> has character code 27, and “[” is the 27th character in ASCII sequence from A. Similarly, “VA enters the control code cl>. See your DOS manual if you need further information about EDLIN.
1100 ' Start printing 1110 WIDTH "LPT1:",255 1120 LPRINT E$;"D";CHR$(3);CHR$(24);CHR$(O) 'Set HT 1130 LPRINT C$:"Font styles are:" 1140 LPRINT H$;D$;"Draft characters,"; 1150 LPRINT HS:CS:"Courier characters.
- 1730 LPRINT E$;"Sl";"SVBSCRIPT";E$;"T";", " 1740 LPRINT H$:C$;"Download characters: ": -.. 1750 LPRINT E$;"SO"; 'Select superscript 1.
2360 NEXT II 2370 RETURN 2380 ' 2390 ' DATA 2400 ' Super/subscript download character data 2410 DATA 7, 23, 6 2420 DATA 12, 0, 16, 0, 44, 0, 80, 0, 44,120, 64,328, 33,120 2430 DATA 94,128, 33,120, 94,128, 33, 24, 66, 0, 33.
2990 DATA 31,192, 0, 31,240, 0, 31,255, 0, 31,255.240, 31,255,255 3000 DATA 31.255.255, 7,255,255, 0,255,255, 0,255,255, 1,255,240 3010 DATA 3;192, 0. 7,128, 0, 15, 0, 0, 31, 0, 0, 31, OJ O 3020 DATA 31, 0, 0, 31, 0, 0, 31. 0, 0, 31, 0, 0, 31. 0, 0 3030 DATA 31, 0, 0, 31, 0, 0, 31, 0, 0, 31, o, 15, 31.
3620 DATA 15,255,192, 15,255,192, 15,255,192, 15.255.128, 15,255,128 3630 DATA 15,255, 0, 15,255, 0, 15,255, 0, 15,254, 0, 15,254, 0 3640 DATA 252.252.
How the program works This program begins by assigning a number of printer commands to BASIC string variables (lines 1000 to 1090). You can find most of these commands near the beginning of chapter 4. The WIDTH “LPTl:” 255 statement in line 1110 means infinite line width.
Font styles are: ;I T ,3 T' i, (,' ) .) ,Aj j ,i <;: f, $f i" ,,j:: , Courier characters, Prestige characters, ORATOR CHARACTERS, Scti.
Modifications for IBM mode This program can also be run in IBM mode (DIP switch l-6 OFF) if you change a few of the lines as shown below to allow for difference in some of the commands. You will get a cylinder instead of a barrel effect, becuase the IBM mode does not have any command to micro-adjust the character spacing.
Chapter 7 TROlJl3LESHOOTING AND MAINTENANCE The following section on troubleshooting and maintenance is intended only as a brief guide to these functions. Remember that your printer is a highly sophisticated electronic device, which also contains high voltage inside.
. Power supply If the POWER indicator does not illuminate, check the following: Check Is the power cable properly plugged into the electrical outlet? Is power being supplied to the outlet? Possible remedy Turn off the printer, ensure the power cable is securely connected, and then turn the printer back on.
If the print is faint, or uneven, check the following: Check Is the ribbon properly in- stalled? Is the ribbon worn out? Possible remedy Check and reinstall if necessary. The ribbon has a long life, but eventually will need replacing. Fit a new ribbon cartridge if necessary.
Paper feeding If cut sheet paper (without the ASF) is not feeding smoothly, check the following: 1 Check I Possible rem& 1 Is the paper release lever I pushed l&k (to the C posi- tion)? Is the paper guide in place The paper guide should be in place vertically for cut and vertical? sheets to feed smoothlv.
Check Are you trying to feed paper using the front panel buttons while the ON LINE indicator is illuminated? Is the paper too thick? Possible remedy You can only feed paper in this way when the printer is off-line. Set the printer off-line and then feed paper.
If the paper park facility does not appear to be working correctly, check the following: Check Possible remedy Is the paper release lever in the C position? The paper release lever must be set to the C position after the fanfold paper has been parked.
MAINTENANCE Essentially, your printer is a robust piece of equipement, but should be treated with a modicum of care in order to avoid malfunctions. For example: l Keep your printer in a “comfortable” environment. Roughly speaking, if you are comfortable, then the environment is suitable for your printer, too (see Chapter 1).
REPLACING THE PRINT HEAD This is not a job which you will need to do very often. The print head has been designed to give a life about 200 million dots.
Figufa 7-4. Replacing the print head 105.
REPLACING THE BATTERY IN THE RAM CARD The optional RAM card has an internal battery that backs up the stored data even when the card is removed from the printer. This battery can be used for more than four years. To avoid losing data from the RAM card, you should replace the battery before the end of its service life.
Chapter 8 SPECIFICATIONS Printing system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Serial Impact Dot-matrix Printing speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200 cps (Draft elite) 66.7 cps (LQ elite) Print direction .
Character dot matrix . . . . . . . . . . . . . . . . . . . . . . Draft Pica 24 x 9 Elite 24 x 9 Semi-condensed 16x7 Condensed pica 24 x 9 Condensed elite 24 x 9 Super/subscript 16x7 Proportional - Super/subscript proportional - Bit image dot-matrix . .
Emulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Epson mode IBM Proprinter mode Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Centronics parallel (standard) RS-232C serial (option) Ribbon type .
The following describes the pinout of the parallel (Centronics-type) inter- face connector (signals which are low when active are overlined): Pin Name Function 1 STROBE Goes from high to low (for 10.
Chapter 9 CHARACTER SETS This chapter gives tables of the printer’s standard and IBM character sets. The decimal character code of each character is shown in an inset to the lower right of the character. The hexadecimal code can be found by reading the entries at the top and left edges of the table.
STANDARD CHARACTER SET - - - IdI - 68 iO0 1% 15 IE IV Ie 1 531 1 691 1 PSI I1011 I& 16 IF IV If ItBEL) I I’ 17 IG IW la 1~~1 39 1 551 1 711 1 871 103 1119 I(BS, IXAW) 81 fl I.
’ . * , L . F 8 D E F I I I I 0 n - 113.
IBM CHARACTER SET #2.
i i 8 9 A B C D E F n c Ii 6 z - - - n I 115.
IBM CHARACTER SET #I Other characters are identical to character set ##2. The duplication of control codes enables systems with a 7-bit interface to obtain control functions when the most significant bit is set to 1 by the <ESC> 3” command.
IBM SPECIAL CH Additional characters can I 0 1 ARACTER SET be printed by special commands. l - 1- 17 8 2 s -r 1 18 v !! 3 3 19 4 ll 117.
INTERNATIONAL CHARACTER SETS When an international character set is selected DIP switches 2-2 to 2-4 or a command from software, the following changes are made in the charac set: IATIN ABEPlCA #$aiRi &iiifibli$Y DENIAPK/NOPYAY #S@[lA’C~>“@O ‘by :ter - - See Chapter 3 for the DIP switch settings.
INDEX El Absolute horizontal tab, 65 Auto feed, 75 Automatic carriage return, 32 Automatic line feed, 34,62 Automatic sheet feeder, 10,33,74,75, 101 m Backspace, 62 Bail lever, 3, 12, 15 BASIC, 26,78,.
El Hexadecimal dump, 25-27 Horizontal position commands, 60-65 Horizontal tabulation, 64 III IBM character sets, 43, 114-l 17 IBM mode, 33,96 IBM-PC, 26,83 Immediate print, 72 Interface: signals, 110 specifications, 109 International characters, 34,44, 118 Italic printing, 22,40 El Justification, 62 Dl Left margin, 60 Letter Quality, 22.
I RAM card, 7,106 Rear cover, 3, 13 Release lever, 3, 10, 13 Reset printer, 75 Reverse line feed, 55 Reverse micro-feed, 29 Ribbon cartridge, 4,97,109 Right margin, 61 ROM character set, 70 I Script f.
COMMAND SUMMARY MODE CONTROL CODE <BEL> <BS> <HT> <LF> <VT> <FF> <CR> <so> <Sb <DCb Std. <DC2> IBM <DC2> Std.
L c L L. MODE CONTROL CODE FUNCTION PAGE IBM Std. Std. IBM <Esc7 “6” cEsc> ‘T <ESC> “8” &SC> “9” <mc> I*.*. <Esc> ‘4:” 47 n <o> <Esc> “<” <ES6 “2 &SC> ‘(=” <07 nl n2 <E.
MODE CONTROL CODE IBM &SC7 “[” “g” nl n2 m0 ml m2 Std. &SC7 ‘T’ nl n2 IBM &SC7 ‘T’ nl n2 IBM <ESC> “A” cESc7 “-” <cb &SC7 ‘* ” <l> <ESC> .‘-** “1” <me .a-.. “1” -disc> UP <o, &SC7 “a” <17 cESC7 “a” <27 cESC7 “a” <37 <WC> ua.
MODE CONTROL CODE IBM E! iii: Std. Std. Std. Std. Std. Std. Std. Std. IBM Std. IBM Std. Std. Std. Std. Std. Std. Std. Std. IBM <Jzsc7 ‘I-‘* 47 <&‘jC> “_” “0” <ESC> ‘*_‘* “1” <Fs> “2” 457 “3” n <Fs> “4” <I?%> “5” <FS> “.
-.
Ein wichtiger Punkt beim Kauf des Geräts Star Micronics NX-2415 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Star Micronics NX-2415 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Star Micronics NX-2415 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Star Micronics NX-2415 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Star Micronics NX-2415 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Star Micronics NX-2415 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Star Micronics NX-2415 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Star Micronics NX-2415. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Star Micronics NX-2415 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
