Benutzeranleitung / Produktwartung MI.61XX des Produzenten Spectrum Brands
Zur Seite of 79
SPECTRUM SYSTEMENTWICKLUNG MICROELE CTRONIC GMBH · AHRENSFELDER WEG 13-17 · 22927 GROSSHANSDORF · GERMANY PHONE: +49 (0)4102-6956 -0 · FAX: +49 (0)4102 -6956-66 · E-MA IL: info@spec.
(c) SPECTRUM SYSTEMENTWICKLUNG MICR OELECTRONIC GMBH AHRENSFELDER WEG 13-17, 22927 GROSSHANSDORF, GERM ANY SBench is a registered trademark of Spectr um Systementwic klung Microelectronic G mbH.
3 Introduction .................................... ..................................... ............................. ............. .... 6 Preface ......................................................................................................
4 Programming the Board ......................... .................................... .................................... . 36 Overview .................. ..............................................................................................
5 Option Gated Replay ........ .................................... ..................................... ...................... 63 Output modes ............ ....................................................................................... .....
6 MI.61xx Manual Preface Introduction Introduction Preface This manual provides detailed information on the hardware featur es of your Spectrum instrumentation boar d. This information inc ludes tech- nical data, specifications, block diagram and a connector description.
Introduction Different models of the MI.61xx series (c) Spectrum GmbH 7 Different models of the MI.61xx series The following overwiew shows the different available models of th e MI.61xx series. They differ in th e number mounted generation modules and the number of available channels.
8 MI.61xx Manual Additional options Introduction Additional options Extra I/O (Opti on -XMF) With this simple-to-use enhancem ent it is possible to control a wide range of external instruments or other equipment. Therefore you have 24 digital I/O and the 4 analog outputs available.
Introduction Additional options (c) Spectrum GmbH 9 Starhub The star hub module allows the syn- chronisation of up to 16 MI boards. It is possible to synchronise boards of the same type with each other as well as different types. The module acts as a star hub for clock and trigger signals.
10 MI.61xx Manual The Spectrum type plate Introduction The Spectrum type plate The Spectrum type plate, which consists of the follo wing components, can be found on all of our boards. The board type, consisting of the two lette rs describing the bus (in this case MI for the PCI bus) an d the model number.
Introduction Hardware information (c) Spectrum GmbH 11 Hardware information Block diagram Technical Data Resolution 8 Bit Dimension 312 mm x 107 mm Integral linearity (DAC) ± 1.5 LSB typ. Width (Sta ndard) 1 full size slot Differential l inearity (DAC) ± 1.
12 MI.61xx Manual Hardware information Introduction Dynamic Parameters Dynamic parameter s are measured at ± 1 V output level and 50 Ohm termination with a spec trum analyser . The samplerate selected is the max imum possible samplerate . Signal fre- quency is equal to the cut-off frequency of the filter.
Hardware Installation System Requirements (c) Spectrum GmbH 13 Hardware Installation System Requirements All Spectrum MI.xxxx instrumen tat ion boards are compliant to the PCI standard and require in genera l one fr ee full length slot. Depending on the installed options additional free slots can be necessary.
14 MI.61xx Manual Installing the board in the system Hardware Installation Installing a board wi th digital inputs/out puts Before installing the board you first need to unscrew and remove the dedicated blind-br ackets usually mounted to cover unused s lots of your PC.
Hardware Installation Installing the board in the system (c) Spectrum GmbH 15 Installing multiple boa rds synchronized b y starhub Hooking up the boards Before mounting several synchronized boards for a multi channel system into the PC yo u can hook up the boar ds with their s ynchr onization cables first.
16 MI.61xx Manual Installing the board in the system Hardware Installation Installing multip le synchronized boards Hooking up the boards Before mounting several synchronized boards for a multi channel system into the PC you can hook up the bo ards with the synchron ization cable first.
Software Driver Installation Interrupt Sharing (c) Spectrum GmbH 17 Software Driver Installation Before using the board a driver must be installed that matches th e operating system. The installati on is done in different ways depending o n the used operating system.
18 MI.61xx Manual Windows 98 Software Driver Installation Windows 98 Installation When installing the board in a Win- dows 98 system the Spectrum board will be recognized automatically on the next start-up. The system offers the direct installa- tion of a driver for the board.
Software Driver Installation Windows 98 (c) Spectrum GmbH 19 After clicking the driver info button the detailed vers ion information of the driver is shown. In the case of a support question this information must be pr esented together with the board’s serial number to the support team to help finding a fast solution.
20 MI.61xx Manual Windows 2000 Software Driver Installation Windows 2000 Installation When installing the board in a Windows 2000 system the Spectrum board will be rec- ognized automatically on the next start-u p. The system offers the direct in- stallation of a driver for the board.
Software Driver Installation Windows 2000 (c) Spectrum GmbH 21 Driver - Update If a new driver version should be installe d no Spectrum board is allowed to be in us e by any software. So please stop and exit all software that could access the boards. A new driver version is direct- ly installed from the device manager.
22 MI.61xx Manual Windows XP Software Driver Installation Windows XP Installation When installing the board in a Windows XP system the Spectrum board will be rec- ognized automatically on the next start-up. The system offers the direct instal lation of a driver for the boa rd.
Software Driver Installation Windows XP (c) Spectrum GmbH 23 On the property page Windows XP shows the dat e and the version of the installed driver. After clicking the driver details button the detailed version inform ation of the driver is shown.
24 MI.61xx Manual Windows NT Software Driver Installation Windows NT Installation Under Windows NT the Spectr um dri ver mu st be i n- stalled manually. The driver is found on CD in the directory InstallWinNTDrv. Please start the „Setup.exe“ pro- gram.
Software Driver Installation Linux (c) Spectrum GmbH 25 Linux Overview The Spectrum boards are delivered with drivers for linux. It is necessary to install them manual ly following th e steps explaine d afterwards. The linux drivers can be found on CD in the directory /Driver/linu x .
26 MI.61xx Manual Linux Software Driver Installation Installing the device You connect a device to the driver with the mknod command. The ma jor number is the number of the driver as shown in the last st ep, the minor number is the index of the board starting with 0.
Software Software Overview (c) Spectrum GmbH 27 Software This chapter gives you an overview about the structure of the dr ivers and the software, where to find and how to use the exa mples.
28 MI.61xx Manual C/C++ Driver Interface Software C/C++ Driver Interface C/C++ is the main programming language for which the drivers have been build up. Theref ore the interface to C/C++ is the best m atch . All the small examples of the manual showing different parts of the hard ware programming are done with C.
Software C/C++ Driver Interface (c) Spectrum GmbH 29 Other Windows C/C++ compilers Include Driver To access the driver, the driver functions must be loaded from the driver dll. This can be easily done by standard windows func tions. There is one example in the directory /Examples/ other that shows the process.
30 MI.61xx Manual C/C++ Driver Interface Software Function SpcSetPa ram All hardware settings are based on software registers that can be set by the function SpcSetParam. This function sets a registe r to a defined value or executes a command. The board must first be initialized.
Software C/C++ Driver Interface (c) Spectrum GmbH 31 Under Linux the additional parameter nBytesPe rSample must be used for this function. For all boards with 8 bit resolution the p arameter is „1“, for all boards with 12, 14 or 16 bit resolution this paramet er has to be „2“.
32 MI.61xx Manual Delphi (Pascal) Programming Interface Software Delphi (Pascal) Pr ogramming Interface Type definiti on All Spectrum driver functions are using pr e-defined variable types to cover different operating systems and to use the same dri ver interface for all programming languages.
Software Delphi (Pascal) Programming Interface (c) Spectrum GmbH 33 This function is only available on generator or i/o boar ds. The function is not available on acquisition boards. Function SpcGetData Reads data from the board from a specific me mo ry channel.
34 MI.61xx Manual Visual Basic Programming Interface Software Visual Basic Prog ramming Interfa ce The Spectrum boards can be used together with Microsoft Visual Ba sic as well as with Microsoft Visual Basic for Applications. T his allows per example the direct access of the hardwa re from within Microsoft Ex cel.
Software Visual Basic Programming Interface (c) Spectrum GmbH 35 Function SpcGetParam The function SpcGetParam reads out software registers or status information. The board must first be initialized. The available software re- gisters for the driver are listed in the board specific part of th e documentation below.
36 MI.61xx Manual Overview Programming the Board Programming the Board Overview The following chapters show you in detail how to program the different aspects of the board. For every topic there’s a small ex ample. For the examples we focussed on Visual C++.
Programming the Board Initialization (c) Spectrum GmbH 37 This means as a result that it is not nece ssary to check each driver call for an error but to check for an error before the boa rd is started to see whether all settings ha ve been vali d. By reading all the error information one can easily examine wher e the error occure d.
38 MI.61xx Manual Initialization Programming the Board Hardware versi on Since all of the MI, MC and MX boards from Spectrum are modular boards, they consis t of one base board and one or two (only PCI and CompactPCI) piggy-back modules. This register SPC_PCIVERSION gi ves information about the revision of either the base board and the mo- dules.
Programming the Board Initialization (c) Spectrum GmbH 39 Installed features and options The SPC_PCIFEATURES register informs you about the options, that are installed on the b oard. If you want to know about one opti on being installed or not, you need to read out the 32 bit value and mask the interesting bit.
40 MI.61xx Manual Powerdown and reset Programming the Board Example program for the board initialization The following example is only an exerpt to give you an idea on how easy it is to initialize a Spectrum board. Powerdown and reset Every Spectrum board can be set to powerdown mode by software.
Analog Outputs Channel Selection (c) Spectrum GmbH 41 Analog Outputs Channel Selection One key setting that influences all other possible settings is th e channel enable register. An unique feature of the Spectrum b oards is the possibility to program the number of channels you want to use.
42 MI.61xx Manual Setting up the outputs Analog Outputs Setting up the outputs Output Amplifie rs This arbitrary waveform generator board uses separate output am- plifiers for each channel.
Analog Outputs Setting up the outputs (c) Spectrum GmbH 43 Maximum Output Range In order not to generate distorted signals it is nec- essary to keep the total output range as a combina- tion of the set amplitude and offset within a range of ±3000 mV.
44 MI.61xx Manual General description Standard generation modes Standard generation modes General description The generated data is replayed from the on- boa rd memory. These modes allows generating waveforms at very high sample rates with out the need to transfer the data into the board’s on-board memory at high speed.
Standard generation modes Programming (c) Spectrum GmbH 45 Maximum memsize How to read this table: If you have installed the standard amou nt of 8 MSample on your 6111 board and you want to replay all fo ur channels, you have a to tal maximu m memory of 16 MSample * 1/4 = 4 MSample per channel for your data.
46 MI.61xx Manual Programming Standard generation modes Starting without interrupt (classic mode) Command register In this mode the board is started by writing the SPC_START valu e to the command register.
Standard generation modes Programming (c) Spectrum GmbH 47 To prevent the program from this deadlock, a second task must be used which can send the SPC_STOP signal to stop the board. Ano ther possibility, that does not require the need of a second task is to define a timeout value.
48 MI.61xx Manual Programming Standard generation modes Standard mode Writing data to the memory is really easy, if a replay mode is used, that stores no n multiplexed data in the dedicated memory c hannels. The next example shows, how to write the data before replaying tw o channels without multiplexing to both memory channels.
FIFO Mode Overview (c) Spectrum GmbH 49 FIFO Mode Overview General Information The FIFO mode allows to record data continuously and trans- fer it online to the PC (acquisi tion boards) or allows to write data continuously from the PC to the board (generation boards).
50 MI.61xx Manual Programming FIFO Mode When using FIFO mode together with one of the options that allow to have gaps in the generation like Multiple Replay or Gated R eplay one can even run the board with higher s ample rates.
FIFO Mode Programming (c) Spectrum GmbH 51 Analog acquisition or generation boards Digital I/O (701x or 702x ) or pattern generator boards (72xx) Digital I/O board 7005 only We at Spectrum achieved best results when programming the buffer leng th to a number of samples that can hold approximately 100 ms of data.
52 MI.61xx Manual Programming FIFO Mode FIFO mode In normal applications the FIFO mode will run in a loop and process one buffer after the other. There are a few special command s and regi- sters for the FIFO mode: The start command and the wait command both wa it for the signal from the driver that th e next buffer has to be processed.
FIFO Mode Programming (c) Spectrum GmbH 53 The samples are re-named for better readability. A0 is samp le 0 of channel 0, C4 is sample 4 of channel 2, .
54 MI.61xx Manual Overview Clock generation Clock generation Overview The Spectrum boards offer a wide variety of different clock mode s to match all the customers need s.
Clock generation Internally generated sample rate (c) Spectrum GmbH 55 Maximum internal sample rate in MS/s normal (non FIFO) mode Maximum internal sample rate in MS/s in FIFO mode Using plain quartz with no PLL In some cases it is useful for the application not to have the on-board PLL activated.
56 MI.61xx Manual Internally generated sample rate Clock generation Direct external cl ock An external clock can be fed in on the ex ternal clock connector of the board.
Clock generation Internally generated sample rate (c) Spectrum GmbH 57 Example: External cloc k with divide r The extra clock divider can be used to divide an external fed in clock by a fixed value. The exte rnal clock must be > 1 MS/s. T his divided clock is used as a sample clock for the board.
58 MI.61xx Manual General Description Trigger modes and appendant registers Trigger modes and appendant registers General Description Concerning the trigger modes of th e Spectrum MI, MC and MX D/ A boards, you can choose between three external TTL trigger modes and one internal software trigger.
Trigger modes and appendant registers External TTL trigger (c) Spectrum GmbH 59 As the trigger connector is used as an input, y ou can decide wh ether the input is 50 Ohm terminated or not. If you enable th e t ermination, please make sure, that your trigger source is capable to delive r the desired current.
60 MI.61xx Manual External TTL trigger Trigger modes and appendant registers Positive and negative TTL trigger This mode is for detecting the ri sing and falling edges of an ex- ternal TTL signal. The board will trig ger on the first rising or falling edge that is detected after starting the board.
Option Multiple Replay Output modes (c) Spectrum GmbH 61 Option Multiple Replay The option Multiple Replay allows the gene ration of data blocks with multiple tri gger events without restarting the hardware. The on-board memory will be divided into several segments of the same size .
62 MI.61xx Manual Trigger mode s Option Multiple Replay Resulting star t delays The following example shows how to set up the board f or Multiple Replay in standard mode. The se tup would be similar in FIFO mo de, but the memsize register would not be used.
Option Gated Replay Output modes (c) Spectrum GmbH 63 Option Gated Replay The option Gated Replay allows the data generation controlled by an external gate signal.
64 MI.61xx Manual Example program Option Gated Replay Due to the structure of the on-board memory there is another delay at the end of the gate interval.
Option Extra I/O Digital I/Os (c) Spectrum GmbH 65 Option Extra I/O Digital I/Os With this simple-to-use enhancement it is possible to control a wide range of external ins trume nts or other equipment. Therefor e you have several digital I/Os and the 4 analog outp uts available.
66 MI.61xx Manual Analog Outputs Option Extra I/O Analog Outputs In addition to the digital I/Os there are fo ur analog outputs available. These output s are directly programmed with the voltage values i n mV. As the analog outputs are driven by a 12 bit DAC, the output vo ltage can be set in a ste psize of 5 mV.
Synchronization (Option) The different synchronization options (c) Spectrum GmbH 67 Synchronization (Option) This option allows the connection of multip le boards to generate a multi-channel syst em. It is possible to synchronize multiple Spectrum boards of the same type as well as different board types.
68 MI.61xx Manual The setup order for the different synchr onization options Synchronization (Option) When the boards are synchronized by the option starhub there will be no delay between the connected boards.
Synchronization (Option) The setup order for the different synchronization options (c) Spectrum GmbH 69 (3) Define the board(s) for trigger master At least one board must be set as the trigger master to get sync hronization running. Every one of the synchronized boards can b e programmed for beeing the trigger master device.
70 MI.61xx Manual The setup order for the different synchr onization options Synchronization (Option) After you have excluded one or more of th e installed boards from the synchronization tr igger it is possible to change the trigg ermodes of these boards.
Synchronization (Option) The setup order for the different synchronization options (c) Spectrum GmbH 71 (9) Start all of the trigger master boards After having armed the synchronized boar ds, you must start all of the boards, that are defined as trigger masters.
72 MI.61xx Manual The setup order for the different synchr onization options Synchronization (Option) Setup synchronizati on for use with FIFO mode and eq ually clocked boa rds Most of the steps are similar to the setup routine for standard synchronization mentioned before.
Synchronization (Option) The setup order for the different synchronization options (c) Spectrum GmbH 73 (8) Start all of the trigger slave boards After having armed the synchronized boards, you must start all of the boards, that are defined as trigger slaves first.
74 MI.61xx Manual The setup order for the different synchr onization options Synchronization (Option) Additions for syn chronizing different bo ards General information Spectrum boards with different speed gr ades, different number of channels or even just differen t clock settings for the same ty pes of boards can be synchronized as well.
Synchronization (Option) The setup order for the different synchronization options (c) Spectrum GmbH 75 Setting up the clock divider The clock divider can easily be set by the following register. Plea se keep in mind that the divider mu st be set for every synch ronized board to have synchronization working correctly.
76 MI.61xx Manual The setup order for the different synchr onization options Synchronization (Option) Additions for equal boards with differ ent sample rates In addition to the possibility of synchron.
Appendix Error Codes (c) Spectrum GmbH 77 Appendix Error Codes The following error codes could occur when a driver function has been called. Please check carefully the allow ed setup for the register and change the settings to run the program. error name value (hex) value (dec.
78 MI.61xx Manual Pin assignment of the multipin conn ector Pin assignment of the multipin connector The 40 lead multipin connector is the main connecto r for all of Spectrum’s digital boards and is.
Pin assignment of the internal multipin connector (c) Spectrum GmbH 79 Pin assignment of the in ternal multipin connector The 26 lead internal connector is used for the option “Extra I/O“ (-XIO) without the external connector described before. The connector mentioned here is m ounted on the bottom side of the Extra I/O modu- le.
Ein wichtiger Punkt beim Kauf des Geräts Spectrum Brands MI.61XX (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Spectrum Brands MI.61XX noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Spectrum Brands MI.61XX - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Spectrum Brands MI.61XX reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Spectrum Brands MI.61XX erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Spectrum Brands MI.61XX besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Spectrum Brands MI.61XX verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Spectrum Brands MI.61XX. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Spectrum Brands MI.61XX gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
