Benutzeranleitung / Produktwartung 21166904 des Produzenten Spalding
Zur Seite of 25
1 10/04 P/N 211669 04 T oll-Free Customer Service Number for U.S: 1-800-558-5234 Internet Address: http://www .hydra-rib.com IMPORT ANT! Have any questions?...Don’t go back to the store! We appreciate your purchasing one of our many fine products. We are sure that you will be very satisfied with your selection.
2 P/N 211669 04 10/04 IMPORT ANT! WRITE MODEL NUMBER FROM BOX ONT O P AGE 1 OF THIS OWNERS MANUAL W ARNING F AILURE T O FOLLO W THESE W ARNINGS MA Y RESUL T IN SERIOUS INJUR Y AND/OR PR OPERTY D AMA GE. Owner must ensure that all pla yers kno w and follo w these rules for saf e operation of the system.
3 10/04 P/N 211669 04 24" (61 cm) 36" (91.4 cm) Ensure ground is level with playing surface, then dig pole hole. GROUND SURFACE PLAYING SURFACE 1. Install threaded ends of J-bolts (1) through holes in mounting plate (3) and secure as shown. NOTE: Make sure J-bolts (1) are in the illustrated position.
4 P/N 211669 04 10/04 Fill hole with concrete. Tamp down concrete to release air pockets and build drainage hill. Insert J-bolts (1) from mounting plate (3) into cement as shown. Move assembly around to release any air pockets in cement, then rest mounting plate on cement drainage hill.
5 10/04 P/N 211669 04 Upright pole (5). Assemble lower pole flange onto protruding J-bolts (1) as shown. The flange will then rest on the nuts (2) from Step 2. Secure pole (5) flange to mounting plate (3) as shown. Tighten completely. 6. 7. 5 TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE.
6 P/N 211669 04 10/04 8. Insert caps (8) into end of each support arm (9) as shown. Tap firmly in position. Apply logo label (11) to lower support arms (9) as shown. Repeat for opposite side. Beginning with upper support arms (9) secure support arms to pole.
7 10/04 P/N 211669 04 1 1. 16 4 13 9 4 7 4 9 7 4 9 7 4 16 4 7 4 9 16 4 16 TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN SERIOUS BODILY INJURY AND/OR PROPERTY DAMAGE. WARNING IMPOR T ANT! Do not over tighten.
8 P/N 211669 04 10/04 12. Install cross brace (17) with nuts (59) and bolts (22) as shown. Repeat for opposite side. 17 22 59.
9 10/04 P/N 211669 04 53 4 4 13. Install vertical supports (18), nuts (2), washers (4) and bolts (53) as shown. 4 4 2 2 53 18 IMPOR T ANT! The end with the double holes need to be toward the playing s.
10 P/N 211669 04 10/04 14. Attach handle plates (21) to vertical supports (18) as shown. Attach cable bracket (20) to handle plates (21) as shown. 54 23 23 54 23 23 55 55 54 54 21 20 21 18 18 SIDE VIE.
11 10/04 P/N 211669 04 15. Remove tie strap that secures cable to strut assembly. Slide shroud (36, 46) over strut assembly (35) as shown. 16. Mount activator bracket (47) to strut assembly (35) with hardware as shown. 35 46 47 56 63 36 35 35 46 CAUTION! Do not depress valve stems.
12 P/N 211669 04 10/04 17. Attach strut/shroud assembly to crossbrace (17) and pole as shown. 7 65 59 61 17.
13 10/04 P/N 211669 04 18. Run the cable from strut assembly around the pole, through the hole in the vertical support (18) and down through the hole in the cable bracket as shown (20). Place one nut on top of the cable bracket and one below as illustrated.
14 P/N 211669 04 10/04 Begin trigger assembly by pulling wire through slot on trigger(48) as shown. Complete this assembly by installing trigger to plates with bolt (53) and bolt (58). Carefully attach cable end to actuator plate (47). 7 42 52 58 66 19 A.
15 10/04 P/N 211669 04 20. Slide shroud over strut assembly and attach shroud with screw (60) as shown. 60.
16 P/N 211669 04 10/04 RIM ASSEMBL Y & INST ALLA TION WARNING 21. Install carriage bolt (41) through rim (25), washers (4) and (27) as shown. Tighten nut (43) completely. Place nut (42) about half-way up carriage bolt (41) as shown. 25 4 41 27 43 TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE.
17 10/04 P/N 211669 04 24. 25 39 40 Insert spacer (45) through rim assembly (25). Place rim assembly on bracket (39) so that carriage bolt (41) is inserted through hole on top of inner bracket (40). Install hex bolt (44), washers (27) and nut (42) through top holes on bracket (39) through spacer (45) as shown.
18 P/N 211669 04 10/04 26. 27. 28. Apply logo label (33) to cover plate (31). Install cover plate (31) on rim (25) using self tapping screws (32) as shown. LEVELING INSTRUCTIONS: Place level on rim (25) and adjust nut (42) until level. Tighten nut (30) to set rim tension for playing.
19 10/04 P/N 211669 04 Apply height adjustment label (37) to front of pole as shown. 30. 10 feet (3.05 m) REGULATION RIM HEIGHT IS 10 FEET (3.05 m). 37 29. Check leveling at this time. Pole should be level in all directions. NOTE: If adjustment is necessary, adjust system by rotating the nuts (2) between mounting plate (3) and pole flange.
20 P/N 211669 04 10/04 31. Attach hook (49) to height strip (50) as shown. Attach this assembly to unit with bolt (12) and nut (7) as shown. 49 50 12 15 63 62.
21 10/04 P/N 211669 04 51 51 57 32. Attach height window (51) to pole using four pieces of double-sided tape (57) as shown. 50 11 1/2” Secure pole pad (35) as shown.
22 P/N 211669 04 10/04 To install height marking labels (10), raise backboard so that the rim is 10’ off the playing surface (two people required for this procedure). Remove 10’ mark label from sheet and insert label on (50) through window of (51).
23 10/04 P/N 211669 04 V alve V alve T rigger released, locking elevator T rigger squeezed, unlocking elevator If the elevator is still difficult to operate, verify that the valves located on the strut are fully depressed when the trigger is activated.
24 P/N 211669 04 10/04 Item Qty. Part No. Description 1 4 200573 J-Bolt, 1/2”-13 x 24” 2 12 265575 Nut, Hex 1/2”-13 3 1 920880 Mounting Plate 4 23* 203474 Washer, Flat 1/2” x 1” O.
25 10/04 P/N 211669 04 Item #41 (1) Item #30 (1) Item #32 (2) Item #42 (2) HARDW ARE IDENTIFIER Item #44 (1) Item #45 (1) Item #43 (1) WARRANTY CARD: Please remember to complete your product registration form on-line at: www.
Ein wichtiger Punkt beim Kauf des Geräts Spalding 21166904 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Spalding 21166904 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Spalding 21166904 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Spalding 21166904 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Spalding 21166904 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Spalding 21166904 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Spalding 21166904 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Spalding 21166904. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Spalding 21166904 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
