Benutzeranleitung / Produktwartung 6KB82440 des Produzenten SOYO
Zur Seite of 46
6KB 82440 LX PCI Mainboard User’s Guide & Technical Reference.
® C C F Tested To Comply With FCC Standards FOR HOME OR OFFICE US E ™ About This Guide This UserÕs Guide is for assisting system manufacturers and end users in setting up and installing the mainboard. Information in this guide has been carefully checked for reliability; however, no guarantee is given as to the correctness of the contents.
iii Table of Contents Chapter 1: Introduction .................................................. 1 Key Features ............................................................................... 1 Unpacking the Mainboard .................................
iv Chapter 3: BIOS Setup .................................................. 19 Standard CMOS Setup .............................................................. 20 BIOS Features Setup ................................................................. 21 Chipset Features Setup .
1 Introduction The 82440 LX PCI mainboard is a high-performance ATX architecture system board that supports 686 (PII) family CPUs. This mainboard is fully compatible with industry standards, and adds many technical enhancements.
2 Introduction Unpacking the Mainboard The mainboard package contains: ¥ The 82440LX Mainboard ¥ This User's Guide ¥ One Triones IDE Bus Master Drivers Diskette Note: Do not unpack the mainboard until you are ready to install it. Follow the precautions below while unpacking the mainboard.
Introduction 3 Mainboard Layout w/ Default Settings 2 2 3 4 5 6 10 9 9 11 11 12 15 15 13 14 16 17 7 1 8 Figure 1Ð1. Mainboard Layout 1. Slot 1 for PII CPU 9. IDE1/IDE2 Connector 2. 82440LX Chipset 10. Floppy Connector 3. Ultra I/O Chip 11. COM1/COM2 Connector 4.
4 Introduction Default settings are as follows: 686 (PII) 233MHz CPU, On-board PCI Bus IDE Enabled, FDC Enabled, 2 high speed UARTS Enabled (w/ 16550 FIFO), 1 EPP/ECP port (ECP + EPP mode), and ATX Power Supply. #3 #2 #1 #2 #3 #4 82371 AB IDE2 IDE1 FDC COM2 COM1 USB1 USB2 PS/2 KB Conn.
2 Hardware Setup This chapter explains how to configure the mainboardÕs hardware. After you install the mainboard, you can set jumpers, install memory on the mainboard, and make case connections. Refer to this chapter whenever you upgrade or reconfigure your system.
6 Hardware Setup SW1: Bus Fraction Core/Bus Ratio Select Jumper Set this jumper according to your CPU clock. Ratio 686 (PII) Family SW1 3.5x (default) 686 (PII) Ð 233 MHz 5 4 23 1 ON 4.0x 686 (PII) Ð 266 MHz 5 4 23 1 ON 4.5x 686 (PII) Ð 300 MHz 5 4 23 1 ON 5.
Hardware Setup 7 686 (PII) Ð 266 CPU Settings (4.0 x clock) FLASH BIOS SW1 5 4 23 1 ON Figure 2Ð1Ð2. CPU Jumper Settings 686 (PII) Ð 300 CPU Settings (4.5 x clock) FLASH BIOS SW1 5 4 23 1 ON Figure 2Ð1Ð3. CPU Jumper Settings 686 (PII) Ð 330 CPU Settings (5.
8 Hardware Setup Multi I/O Port Addresses Default settings for multi-I/O port addresses are shown in the table below. Port I/O Address IRQ Status LPT1* 378H 7 ECP + EPP COM1 3F8H 4 COM2 2F8H 3 * If default I/O port addresses conflict with other I/O cards (e.
Hardware Setup 9 PS/2 Mouse Connector A six-pin female PS/2 mouse connector is located at the rear of the board. Plug the mouse jack into this connector. IR – IR Connector A ten-pin wafer connector is for connecting to the IR device. Use the device that has the ASKIR or HPSIR specification and choose ASKIR/HPSIR from the BIOS setup.
10 Hardware Setup IDE1/IDE2 – On-board Primary/Secondary IDE HDD Connectors Attach on-board hard disk drives to these connectors. COM1/COM2 Connectors Connect COM1/COM2 devices to these connectors. IDE LED – IDE HDD LED Connectors Attach on-board IDE device LEDs to this connector.
Hardware Setup 11 FAN: CPU Cooling Fan Connector This 3-pins connector provides 12V power for the CPU cooling fan which matches the pin assignment of this connector. If you enable the Suspend Mode function in BIOS setup, this fan will stop when the system is into the suspend mode.
12 Hardware Setup Slot 1 Installation Guide This mainboard provides a non-boxed 686 (PII) CPU retention set to secure the CPU on this board. Follow the steps below to secure this type of CPU on to your motherboard. Step 1: Find the ATX PW and the Slot 1 on the board and set the board in the direction as follows before doing any installation.
Hardware Setup 13 Step 2: Insert the supporting base, which is shown below, into the two holes directly to the left of the 2 sets of screws that have just been inserted on to the board.
14 Hardware Setup Step 3: Insert the 2 latches into the two holes of the supporting base and then turn them 90¡ to secure the CPU. ATX PW.
Hardware Setup 15 Step 4: Set the retention clip right on the top of the 2 sets of screws which are along the sides of Slot1 and then tighten the 4 screws on the retention clip.
16 Hardware Setup Step 5: Insert the CPU into the retention clip and notice that the heat sink is on the left hand side of the board. Lock the two latches on the sides of the CPU to secure the CPU.
Hardware Setup 17 Step 6: Insert the clip portion of the CPU supporter, which is shown below, so that the heat sink can sit on the top of the whole CPU supporter.
3 BIOS Setup The mainboardÕs BIOS setup program is the ROM PCI/ISA BIOS from Award Software Inc. Enter the Award BIOS programÕs Main Menu as follows: 1. Turn on or reboot the system. After a series of diagnostic checks, you are asked to press DEL to enter Setup.
BIOS Setup 19 Standard CMOS Setup Run the Standard CMOS Setup as follows. 1. Choose ÒSTANDARD CMOS SETUPÓ from the Main Menu. A screen appears. ROM PCI/ISA BIOS STANDARD CMOS SETUP AWARD SOFTWARE, INC.
20 BIOS Setup Video Choose Monochrome, Color 40x25, VGA/EGA (default), Color 80x25 Floppy 3 Mode Support Choose Disabled (default) or Enabled. When enables this function, the system will support 720KB/1.25MB/1.44MB 3 different modes floppy diskette. Note: This function is for a special disk drive which happens to be popular in Japan.
BIOS Setup 21 BIOS Features Setup Run the BIOS Features Setup as follows. 1. Choose ÒBIOS FEATURES SETUPÓ from the Main Menu and a screen with a list of items appears. ( The screen below shows the BIOS default settings. ) ROM PCI/ISA BIOS BIOS FEATURES SETUP AWARD SOFTWARE, INC.
22 BIOS Setup Boot Sequence Choose the boot device sequence as your need. For example, ÒA, C, SCSIÓ means that BIOS will look for an operating system first from drive A, drive C, then SCSI device.
BIOS Setup 23 PCI/VGA Palette Snoop Enabled: The color of the monitor may be incorrect if uses with MPEG card. Enable this option to make the monitor normal. Disabled: Default setting. OS Select for DRAM >64MB OS2: Choosing this when you are using OS/2 operation system.
24 BIOS Setup Chipset Features Setup The Chipset Features Setup option changes the values of the chipset registers. These registers control system options in the computer. Note: Change these settings only if you are familiar with the Chipset. Run the Chipset Features Setup as follows.
BIOS Setup 25 EDO RAS# Precharge Time Use the default setting. EDO DRAM Read Burst Use the default setting. DRAM Write Burst Use the default setting. DRAM Data Integrity Mode Choose Non-ECC (default) or ECC according to the DRAM type you have. CPU-TO-PCI IDE Posting Use the default setting.
26 BIOS Setup SDRAM RAS-to-CAS Delay Use the default setting. SDRAM RAS Precharge Time Use the default setting. SDRAM CAS Latency Time Use the default setting. Spread Spectrum Modulated Enabled it when you want to run the FCC or DOC testing. CPU Warning Temperature Choose Disabled (default) or Enabled .
BIOS Setup 27 Power Management Setup The Power Management Setup option sets the systemÕs power saving functions. Run the Power Management Setup as follows. 1. Choose ÒPOWER MANAGEMENT SETUPÓ from the Main Menu and a screen with a list of items appears.
28 BIOS Setup PM Control by APM Choose Yes or No (default). APM stands for Advanced Power Management. To use APM, you must run Òpower.exeÓ under DOS v6.0 or later version. Video Off Method Choose V/H Sync+Blank (default), Blank screen, or DPMS for the selected PM mode.
BIOS Setup 29 PNP/PCI Configuration Setup This option sets the mainboardÕs PCI Slots. Run this option as follows: 1. Choose ÒPNP/PCI CONFIGURATION SETUPÓ from the Main Menu and the following screen appears. (The screen below shows default settings.
30 BIOS Setup IRQX and DMAX assigned to Choose PCI/ISA PnP or Legacy ISA. If the first item is set to Manual, you could choose IRQX and DMAX assigned to PCI/ISA PnP card or ISA card. PCI/ISA PnP: BIOS auto assigns IRQ/DMA to the device. Legacy ISA: User assigns IRQ/DMA to the device.
BIOS Setup 31 Load BIOS Defaults Choose this item and the following message appears: ÒLoad BIOS Defaults (Y/N)?NÓ To use the BIOS defaults, change the prompt to ÒYÓ and press <Enter>. Note: BIOS DEFAULTS values are adjusted for high performance.
32 BIOS Setup IDE HDD Block Mode Choose Enabled (default) or Disabled. Enabled invokes multi-sector transfer instead of one sector per transfer. Not all HDDs support this function. IDE Primary Master PIO IDE Primary Slave PIO IDE Secondary Master PIO IDE Secondary Slave PIO Choose Auto (default) or mode 0~4.
BIOS Setup 33 Onboard Parallel Port Choose the printer I/O address: 378H/IRQ7 (default), 3BCH/IRQ7, 278H/IRQ5 Onboard Printer Mode Choose SPP, ECP, EPP/SPP, or ECP/EPP mode. The mode depends on your external device that connects to this port. ECP Mode Use DMA Choose 3 (default) or 1 to select DMA3 or DMA1 when using the ECP device.
34 BIOS Setup Supervisor Password Based on the setting you made in the ÒSecurity OptionÓ of the ÒBIOS FEATURES SETUPÓ, this Main Menu item lets you configure the system so that a password is required every time the system boots or an attempt is made to enter the Setup program.
BIOS Setup 35 User Password Based on the setting you made in the ÒSecurity OptionÓ of the ÒBIOS FEATURES SETUPÓ, this Main Menu item lets you configure the system so that a password is required every time the system boots or an attempt is made to enter the Setup program.
36 BIOS Setup IDE HDD Auto Detection This Main Menu item automatically detects the hard disk type and configures the STANDARD CMOS SETUP accordingly. Note: This function is only valid for IDE hard disks. ROM PCI/ISA BIOS CMOS SETUP UTILITY AWARD SOFTWARE, INC.
4 Drivers Installation Guide Triones IDE Bus Master Drivers Installation Guide is for Intel PIIX/PIIX3 Chipset. MS-DOS/WINDOW/WFW 1) You should install CD-ROM in secondary channel in Windows (WFW). 2) Change the current directory to a: or b:. 3) Under DOS command line prompt, run the SETUP directly.
38 Drivers Installation Guide WINDOWS 95 1) Close any running applications. 2) Insert the floppy disk into drive A:. 3) Open ÒMy ComputerÓ, double click ÒDrive A:Ó. 4) Double click ÒWin95Ó. 5) Double click the Setup program. 6) Then just follow the instruction.
Drivers Installation Guide 39 4) From root directory, type the following commands: mkdir/inst cd /inst tar xvf /tmp/trisco.tar. (Note: there is a period at the end of the last command.) 5) Now, insert a blank diskette into the floppy drive A and type: tar cvf /dev/<your floppy drive A device name>.
40 Drivers Installation Guide 4) From root directory, type the following commands: mkdir/inst cd /inst tar xvf /tmp/trisco.tar. (Note: there is a period at the end of the last command.) 5) Install the driver by typing: ./install 6) Reboot your SCO UNIX system.
Quick Installation Guide 41 Quick Installation Guide This Quick Installation Guide leaflet is designed for those people who are familiar with motherboard settings to set up this new motherboard in order to boot up the system. Refer back to the proper chapters if you have run in to any problems.
42 Quick Installation Guide Memory Configurations DIMM BANKS DIMM1 DIMM2 DIMM3 DIMM4 RAM Type EDO/SDRAM Size 8/16/32/64/128 Note: This mainboard requires 3.3V DIMM with an access time of 70ns or less, it supports memory size from 8 to 512MB and you may use any combination of DIMMs in the banks.
Ein wichtiger Punkt beim Kauf des Geräts SOYO 6KB82440 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie SOYO 6KB82440 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für SOYO 6KB82440 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von SOYO 6KB82440 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über SOYO 6KB82440 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon SOYO 6KB82440 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von SOYO 6KB82440 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit SOYO 6KB82440. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei SOYO 6KB82440 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
