Benutzeranleitung / Produktwartung SLV-X847ML des Produzenten Sony
Zur Seite of 76
1 Introduction PAL NTSC Video Cassette Recor der ©1997 by Sony Corporation SL V -X847ML Operating Instructions G 3-861-476- 11 (1).
Introduction 2 W ARNING T o prevent fir e or shock hazard, do not expose the unit to rain or moisture. T o avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only . The mains lead must only be changed at a qualified service shop.
3 Introduction T able of contents Getting Started 4 Step 1: Unpacking 5 Step 2: Setting up the r emote commander 8 Step 3: Connecting the VCR 11 Step 4: T uning your TV to the VCR 14 Step 5: Setting u.
4 Getting Started • Remote commander • R6 (size AA) batteries Getting Started • Aerial cable • Audio/video cable (3-phono to 3-phono) Step 1 Unpacking Check that you have received the followin.
5 Getting Started Getting Started Step 2 Setting up the r emote commander Inserting the batteries Insert two R6 (size AA) batteries by matching the + and – on the batteries to the diagram inside the battery compartment. Insert the negative (–) end first, then push in and down until the positive (+) end clicks into position.
6 Getting Started Contr olling other TVs with the remote commander The r emote commander is prepr ogrammed to control non-Sony TVs. If your TV is listed in the table below , set the appropriate manufactur er ’s code number . 1 Set TV / VIDEO at the top of the remote commander to TV .
7 Getting Started Getting Started Manufactur er Sony Aiwa Akai Blaupunkt Brionvega C.G.M Colonad Dual Emerson Fenner Fer guson Gold Star Gr undig Hitachi Hyper Inno-Hit Irradio ITT JVC Loewe Mitsubish.
8 Getting Started 1 Disconnect the aerial cable fr om your TV and connect it to AERIAL IN on the r ear panel of the VCR. 2 Connect AERIAL OUT of the VCR and the aerial input of your TV using the supplied aerial cable. 3 Connect the mains lead to the mains.
9 Getting Started Getting Started Additional connections T o a TV that has phono type audio/ video input jacks This additional connection impr oves picture and sound quality . Connect the TV as shown on the right. If you want to use the T rinitron TV Synchr o Play function (see page 43), this connection is necessary .
10 Getting Started Notes • If a video signal is input to the VCR (via the line input, tuner , or playback), the on- scr een menus will appear on your TV regardless of the NTSC PB switch setting. • If your TV is compatible with the SECAM system, the on-scr een menus may be displayed in black and white.
11 Getting Started Getting Started 1 Pr ess ON/STANDBY to turn on the VCR. 2 Pr ess RF CH SET on the VCR with a ball-point pen, etc. The factory-preset RF channel appears in the display window . The VCR signal is output through this channel to the TV .
12 Getting Started 4 Pr ess RF CH SET . The TV system indicator appears in the display window . Pr ess PROGRAM +/– to select the desir ed TV system. 5 T une the TV to the same channel as that shown in the display window so that the picture on the right appears on the TV scr een.
13 Getting Started Getting Started T o check to see if the TV tuning is corr ect Set the TV to the video channel and pr ess PROGRAM +/– on the VCR. If the TV scr een changes to a differ ent programme each time you pr ess PROGRAM +/–, the TV tuning is corr ect.
14 Getting Started Setting up the VCR with EASY SET UP Befor e using the VCR for the first time, set up the VCR using the EASY SET UP function. W ith this function, you can set the language for the on-screen display , TV channels, guide channels for G-CODE, and the VCR clock, guided by the sequence indicated on the TV screen.
15 Getting Started Getting Started 5 Press CURSOR > / . to select either I, D/ K, B/G, or M, whichever is applicable in your area, then pr ess EXECUTE. The VCR starts searching for all the receivable channels. During presetting, the channel being located is displayed on the screen.
16 Getting Started Step 5 : Setting up the VCR with EASY SET UP (continued) Notes • Do not exit EASY SET UP while the VCR is pr esetting channels. If you do, repeat EASY SET UP from the beginning. • The channel numbers pr eset using AUT O TUNER PRESET may not match your local channel numbers.
17 Getting Started Getting Started 1 Pr ess MENU, then press CURSOR > / . to move the cursor ( z ) to LANGUAGE and pr ess EXECUTE. 2 Pr ess CURSOR > / .
18 Getting Started Manual setup — Pr esetting channels First, we recommend that you pr eset the receivable channels in your ar ea using EASY SET UP or using automatic pr esetting below .
19 Getting Started Getting Started 2 Pr ess CURSOR > / . / ? / / to move the cursor ( z ) to SYSTEM, then select either I, D/K, B/G, or M, whichever is applicable in your ar ea. If SYSTEM is set to the wr ong position, the sound will be distorted or noisy .
20 Getting Started Presetting channels manually MENU CURSOR > / . / ? / / PROG+/– • CURSOR • CURSOR • CURSOR • EXECUTE • MENU EXECUTE 123 456 789 0 Manual setup — Pr esetting channels (continued) 1 Pr ess MENU, then press CURSOR > / .
21 Getting Started Getting Started • EXECUTE 4 Pr ess PROG +/– to select the pr ogramme position. 5 Pr ess CURSOR / r epeatedly until the channel you want is displayed. Pr essing CURSOR ? goes back to the pr evious channels. The channels are scanned in the or der shown on pages 24 to 31.
22 Getting Started Manual setup — Pr esetting channels (continued) Disabling unwanted pr ogramme positions After tuning the TV channels, you can disable unused pr ogramme positions. The disabled positions will be skipped later when you pr ess the PROG +/– buttons.
23 Getting Started Getting Started If the pictur e is not clear Normally , the Auto Fine T uning (AFT) function automatically tunes in channels clearly . If, however , the picture is not clear , you may also use the manual tuning function. 1 Press PROG +/– to select the programme number for which you cannot obtain a clear picture.
24 Getting Started Manual setup — Pr esetting channels (continued) Channel numbers in the CHANNEL SET field and the corresponding channels TV system Country Channel number in the CHANNEL SET field 1.
25 Getting Started Getting Started TV system Country Channel number in the CHANNEL SET field 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 Cor respond.
26 Getting Started Manual setup — Pr esetting channels (continued) TV system Country Channel number in the CHANNEL SET field 64 65 66 67 68 69 C1 C2 C3 C4 C5 C6 C7 C8 C9 C10 C11 C12 C13 C14 C15 C16 .
27 Getting Started Getting Started TV system Country Channel number in the CHANNEL SET field C28 C29 C30 C31 C32 C33 C34 C35 C36 C37 C38 C39 C40 C41 C42 C43 C44 C45 C46 Cor responding channels B/G Ind.
28 Getting Started Manual setup — Pr esetting channels (continued) TV system Country Channel number in the CHANNEL SET field 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Corr esponding channels D/K Japan East Eur ope UK/Hong Kong Ireland U.
29 Getting Started Getting Started TV system Country Channel number in the CHANNEL SET field 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 Corr esponding channels D/K Japan East Eur ope UK/Hong Kong Ireland U.
30 Getting Started Manual setup — Pr esetting channels (continued) TV system Country Channel number in the CHANNEL SET field 63 64 65 66 67 68 69 C1 C2 C3 C4 C5 C6 C7 C8 C9 C10 C11 C12 C13 C14 C15 C16 C17 C18 C19 C20 C21 C22 C23 C24 Corr esponding channels D/K Japan East Eur ope UK/Hong Kong Ireland U.
31 Getting Started Getting Started TV system Country Channel number in the CHANNEL SET field C25 C26 C27 C28 C29 C30 C31 C32 C33 C34 C35 C36 C37 C38 C39 C40 C41 C42 C43 C44 C45 C46 Corr esponding channels D/K Japan East Eur ope UK/Hong Kong Ireland U.
32 Getting Started Manual setup — Setting up G-CODE G-CODE is a feature in Sony VCRs that simplifies pr ogramming the VCR to make timer recor dings. T o use G-CODE, each pr ogramme position needs to be matched with its G-CODE guide channel.
33 Getting Started Getting Started 3 Pr ess CURSOR / twice to select the guide channel column. 4 Pr ess CURSOR > / . to select the guide channel number assigned in the pr ogramme guide. 5 Pr ess CURSOR ? / / to confirm the setting. 6 T o set the guide channel of another station, r epeat steps 2 to 5.
34 Getting Started Setting up G-CODE for satellite br oadcasts When your satellite tuner is connected via the AERIAL IN connector , first you have to set the pr ogramme position for each satellite channel using the TUNER PRESET menu. Then set the guide channel number for each satellite channel using the SET UP CH AND G-CODE menu.
35 Getting Started Getting Started Manual setup –– Changing/ disabling pr ogramme positions After setting the channels and G-CODE guide channels, you can change the programme positions as you like. If any programme positions ar e unused or contain unwanted channels, you can disable them.
36 Getting Started Manual setup –– Changing/disabling programme positions (continued) 3 Pr ess CURSOR > / . until the selected channel and guide channel r ow moves to the desir ed programme position.
37 Getting Started Getting Started 1 Pr ess MENU, then press CURSOR > / . to move the cursor ( z ) to SET UP CH AND G-CODE and pr ess EXECUTE. When using the EASY SET UP pr ocedure, skip this step. 2 Pr ess CURSOR > / . to move the cursor ( z ) to the row on which you want to disable.
38 Getting Started Manual setup — Setting the clock Y ou must set the time and date on the VCR to be able to use the timer recor ding featur es pr operly . If you have not set the VCR clock in the EASY SET UP pr ocedur e, you need to set it manually .
39 Getting Started Getting Started 4 Set the year , hour and minutes in sequence, using CURSOR / to select the item to be set, and CURSOR > / . to select the digits. 5 Pr ess EXECUTE to start the clock. Tip • T o change the digits during setting, press CURSOR ? to return to the item to be changed, and select the digits using CURSOR > / .
Basic Operations 40 Basic Operations Playing a tape 1 T urn on your TV and set it to the video channel. 2 Insert a tape. The VCR turns on and starts playing automatically if you insert a tape with its safety tab r emoved. 3 Pr ess · PLA Y . When the tape reaches the end, it will r ewind automatically .
Basic Operations 41 Basic Operations To Stop play Pause play Resume play after pause Search forwar d Search backward Fast-forward the tape Rewind the tape Eject the tape Press p STOP P P AUSE P P AUSE.
Basic Operations 42 Playing a tape (continued) T o use the time counter At the point on the tape that you want to find later , pr ess COUNTER RESET . The counter in the display window r esets to “0H00M00S.” Search for the point afterwards by r eferring to the counter .
Basic Operations 43 Basic Operations T urning on the VCR and TV , and starting playback automatically (T rinitron TV Synchr o Play) Y ou can only use this function if your TV is made by Sony (T rinitron TV).
Basic Operations 44 1 T urn on your TV and set it to the video channel. 2 Insert a tape with its safety tab in place. Recor ding TV pr ogrammes PROG +/– T APE SPEED r REC 123 456 789 0.
Basic Operations 45 Basic Operations 3 Pr ess PROG +/– to select the programme position you want to recor d. 4 Pr ess T APE SPEED to select the tape speed (SP or LP for the P AL colour system, and SP or EP for the NTSC colour system). LP pr ovides recording time twice as long as SP .
Basic Operations 46 Tips • T o select a pr ogramme position, you can use the pr ogramme number buttons on the remote commander . For two-digit numbers, press the ? (ten’s digit) button followed by the pr ogramme number buttons. • Y ou can select a video source from the LINE-1 IN or the LINE 2 IN jacks using the INPUT SELECT button.
Basic Operations 47 Basic Operations 1 Pr ess G-CODE. Recording TV pr ogrammes using G-CODE Just enter the programme’s G-CODE number listed in the TV pr ogramme guide. The date, times and programme position of that programme are set automatically . Y ou can pr eset up to eight pr ogrammes at a time.
Basic Operations 48 Recor ding TV programmes using G-CODE (continued) 2 Pr ess the pr ogramme number buttons to enter the pr ogramme’s G-CODE number . If you make a mistake, press TIMER CLEAR and re-enter the corr ect number . 3 Pr ess T APE SPEED to select the tape speed, SP or LP .
Basic Operations 49 Basic Operations T o r ecord satellite broadcasts If you connect the satellite tuner and the VCR, you can r ecor d satellite pr ogrammes. 1 T urn on the satellite tuner . 2 On the satellite tuner , select the satellite programme for which you wish to make a timer setting.
Basic Operations 50 Setting the timer manually The VCR automatically starts and stops recor ding TV pr ogrammes. Y ou can pr eset up to eight programmes at a time. Before you start… • Check that the VCR clock is set to the correct time. • Insert a tape with its safety tab in place.
Basic Operations 51 Basic Operations the curr ent date n SUN-SA T n MON-SA T n MON-FRI n EVER Y SA T ..... n EVER Y MON n EVER Y SUN n 1 month later n (dates count down) n the current date • CURSOR • EXECUTE • CURSOR • TIMER SET / CHECK SAT 25 .
Basic Operations 52 T o use the VCR after setting the timer T o use the VCR before a timer r ecor ding begins, just pr ess u . The TIMER indicator turns of f and the VCR switches on. Remember to press u to r eset the VCR after using the VCR. Y ou can also do the following tasks while the VCR is recor ding: • Reset the counter .
Additional Operations 53 Additional Operations Playing/sear ching at various speeds 0 REW ) FF Playback options Fast-forward/r ewind V iew the pictur e during fast- forwar d or rewind Play at high spe.
Additional Operations 54 Tip • Adjust the pictur e using TRACKING +/– on the VCR if: – streaks appear while playing in slow motion. – bands appear at the top or bottom while pausing. – the pictur e shakes while pausing. Notes • The playback sound is muted during these operations.
Additional Operations 55 Recording TV pr ogrammes using the quick timer After starting r ecor ding in the normal way , you can have the VCR stop recor ding automatically after a specified duration. 1 While recording, press QUICK TIMER on the VCR once.
Additional Operations 56 Checking/ changing/ cancelling timer settings Before you start… • T urn on your TV and set it to the video channel. 1 Press u to turn on the VCR. 2 Press MENU, then select TIMER SET/CHECK: • If you want to change a setting, go on to the next step.
Additional Operations 57 Recording ster eo and bilingual pr ogrammes In ZWEITON (German ster eo) system This VCR automatically r eceives and records stereo and bilingual pr ogrammes based on the ZWEIT ON system only when the SYSTEM (I, D/ K, B/G, or M) option in the TUNER PRESET menu is set to B/G.
Additional Operations 58 Recor ding stereo and bilingual programmes (continued) Bilingual pr ogramme * Usually the main sound (monaural) Selecting the sound during playback Pr ess AUDIO MONIT OR to select the sound you want.
Additional Operations 59 How sound is recor ded on a video tape The VCR r ecor ds sound onto two separate tracks. Hi-fi audio is r ecor ded onto the main track along with the pictur e. Monaural sound is recorded onto the normal audio track along the edge of the tape.
Additional Operations 60 Searching with the index function Y ou can search for the start of a specific passage or scene. The VCR can search up to 99 index signals ahead of or behind the curr ent position. = / + INDEX SEARCH 123 456 789 0 INDEX SEARCH 8 1 Insert an indexed tape into the VCR.
Additional Operations 61 About Adaptive Picture Contr ol (APC) Adaptive Picture Contr ol (APC) automatically impr oves recording and playback quality by adjusting the VCR to the condition of the video heads and tape.
Additional Operations 62 Menu option BUZZER AUDIO MIX HIFI AUDIO APC P AL/MESECAM Changing menu options 1 Press MENU, then select SET UP MENU. 2 Press CURSOR > / . to select the option to change, then pr ess CURSOR ? / / to change the setting. 3 Press EXECUTE to return to the original screen.
63 Editing This VCR (Recorder) TV Tip • Y ou can also use the LINE-1 IN jacks instead. Notes • Make sur e you connect the plugs to jacks of the same colour . • If the other VCR is a monaural type, connect the audio plug to the AUDIO L (white) jack.
64 Editing r REC Basic editing (when r ecording on this VCR) Before you start editing • T urn on your TV and set it to the video channel. • Press INPUT SELECT to display “L2” (or “L1”) in the display window .
65 Additional Information T roubleshooting Symptom The ON/ST ANDBY switch does not function. The power is turned on but the VCR does not operate. The clock has stopped and “–:– –” lights in the display window . The playback picture does not appear on the TV screen.
66 Additional Information T roubleshooting (continued) Recording Timer recording Playback Symptom The picture rolls vertically during picture sear ch. The picture has no sound. The sound is unstable or has an echo. No TV programmes appear on the TV scr een.
67 Additional Information Symptom A tape cannot be inserted. The remote commander does not function. The tracking indicator does not appear on the scr een. The VCR needs to be cleaned. Remedy • Check that a tape isn’t already in the tape compartment.
68 Additional Information Specifications System Channel coverage VHF R1 to R12, E2 to E12, NZ1 to NZ1 1 UHF E21 to E69, R21 to R60 CA TV S01 to S05, S1 to S41 RF output signal UHF channels 21 to 69 Ae.
69 Additional Information Index to par ts and contr ols Front panel Refer to the pages indicated in parentheses ( ) for details. 1 EASY SET UP button (14) 2 ON/ST ANDBY switch/indicator (1 1) 3 Multi .
70 Additional Information Index to parts and controls (continued) Display window 8 (T racking) indicator (61) 9 TV system indicator (12) I/G/K/M !º Audio channel/sound level indicator (58) !¡ STEREO.
71 Additional Information 1 Mains lead (8) 2 LINE-1 IN AUDIO L/R/VIDEO jacks (63) 3 AERIAL OUT connector (8) 4 AERIAL IN connector (8) 5 NTSC PB switch (41) 6 LINE-1 OUT AUDIO L/R/VIDEO jacks (9) Rear.
72 Additional Information Index to parts and controls (continued) Remote commander 1 TV / VIDEO r emote control switch (5) 2 6 ␣ EJECT button (41) 3 Menu buttons (14) MENU button CURSOR > / .
73 Additional Information !§ u ␣ (on/standby) switch (14) !¶ AUDIO MONITOR button (57) !• TV/VIDEO button ( for TV ) (6) !ª G-CODE button (47) @º Programme number/ ? (ten’s digit) buttons (4.
74 Additional Information.
75 Additional Information.
76 Additional Information Sony Corporation A, B Accessories supplied 4 Adjusting picture 23, 54, 61 tracking 54, 61 Aerial hookup 8 AFT (Auto Fine T uning) 23 APC (Adaptive Pictur e Control) 61 Audio .
Ein wichtiger Punkt beim Kauf des Geräts Sony SLV-X847ML (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Sony SLV-X847ML noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Sony SLV-X847ML - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Sony SLV-X847ML reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Sony SLV-X847ML erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Sony SLV-X847ML besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Sony SLV-X847ML verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Sony SLV-X847ML. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Sony SLV-X847ML gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
