Benutzeranleitung / Produktwartung SLV-998HF des Produzenten Sony
Zur Seite of 42
SONY ® Video Cassette Recorder Operating Instructions Owner's record The model and serial numbers are located at the rear of the unit. Record these numbers in the spaces provided below. Refer to them whenever you call upon your Sony dealer regarding this product.
WARNING Installing To prevent fire or shock hazard, do * Allow adequate air circulation to prevent internal not expose the unit to rain or heat buildup. moisture. * Do not place unit on surfaces (rugs, blankets, etc.) or near materials (curtains, draperies) that may block the ventilation slots.
Table of contents Getting Started 4 Step 1: Unpacking 5 Step 2: Setting up the remote commander 8 Step 3: Hookups 32 Selecting a language 33 Setting the clock 39 Setting up the cable box control 44 Pr.
Getting Started Step 1 Unpacking Check that you have received the following items with the VCR: Remote commander 75-ohm coaxial cable with F-type connectors Size AA (R6) batteries Jack cover Audio / v.
Step 2 Setting up the remote commander Inserting the batteries Insert two size AA (R6) batteries by matching the + and - on the batteries to the diagram inside the battery compartment. Insert the negative (-) end first, then push in and down until the positive (+) end clicks into position.
Step 2: Setting up the remote commander (continued) Setting the COMMAND MODE switch To remotely control the VCR with the remote commander, set COMMAND MODE on the remote commander to the same position as that on the VCR.
Code numbers of controllable TVs If more than one code number is listed, try entering them one at a time until you find the one that works with your TV.
Step 3 Hookups Selecting the best hookup option There are many ways in which your VCR can be hookep up. To hook up your VCR so that it works best for you, first scan through the table below. Then use the accompanying diagrams and procedures on the following pages to set up your VCR.
Audio/video (A/V) hookup Pages 9 and 10 If your TV has audio / video (A / V) input jacks, you will get a better picture and sound if you hook up your VCR using these connections. In addition, for a true "home theater" experience, you should connect the audio outputs of your VCR or TV to your stereo system.
Step 3: Hookups (continued) C Use this hookup if your TV has the S-Link™ function Note * To play a tape in stereo, you must use the A / V connection. A / V hookup: VCR setup After you've connected your TV and completed antenna or cable hookup, use the following procedure to set up the VCR.
Hookup 1 Pages 11 to 13 Using cable box control Recommended use You should use this hookup if you have a cable box, especially if your cable system scrambles all or most of the channels. This hookup allows the VCR's cable box control feature to control the channel on the cable box, simplifying the recording process.
Step 3: Hookups (continued) Hookup 1: VCR setup 1 Set the RF UNIT switch to CH 3 or CH 4, whichever channel is not used in your area. If both are used, set the switch to either channel. For details, see page 87. If you made A / V connections (from page 9), you can skip this step.
6 Select your cable box output channel and SET UP CABLE BOX SET UP press OK. CABLE BOX CONTROL CABLE MOUSE ON OFF SET UP is done BOX CODE NO. -- -- -- BOX OUTPUT CH CH3 Use to select Push EASY SET UP to quit Hookup 1: VCR Plus+ channel setup Normal display MENU 1 Press MENU and select SET VCR Plus+ TIMER SET / CHECK CHANNELS.
Step 3: Hookups (continued) Hookup 2 Pages 14 to 16 No cable box, or incompatible cable box with only a few scrambled channels Recommended use Use this hookup if you do not have a cable box.
Hookup 2: VCR setup 1 Set the RF UNIT switch to CH 3 or CH 4, whichever channel is not used in your area. If both are used, set the switch to either channel. For details, see page 87. If you made A / V connections (from page 9), you can skip this step.
Step 3: Hookups (continued) 6 The AUTO PRESET SET UP CABLE BOX SET UP starts. AUTO PRESET SET UP is done PROCESSING Please wait!!! Hookup 2: VCR Plus+ channel setup Normal display MENU 1 Press MENU and select SET VCR Plus+ TIMER SET / CHECK CHANNELS.
Hookup 3 Pages 17 to 19 Antenna hookup Make the following connections if you're using an antenna (if you don't have cable TV.) A Use this hookup if you're using: * VHF / UHF antenna (yo.
Step 3: Hookups (continued) Hookup 3: VCR setup 1 Set the RF UNIT switch to CH 3 or CH 4, whichever channel is not used in your area. If both are used, set the switch to either channel. For details, see page 87. If you made A / V connections (from page 9), you can skip this step.
6 The AUTO PRESET SET UP CABLE BOX SET UP starts. AUTO PRESET SET UP is done PROCESSING Please wait!!! Hookup 3: VCR Plus+ channel setup Normal display MENU 1 Press MENU and select SET VCR Plus+ TIMER SET / CHECK CHANNELS.
Step 3: Hookups (continued) Hookup 4 Pages 20 to 23 Incompatible cable box with many scrambled channels Recommeded use Use this hookup if your cable company cannot supply a cable box that is compatible with the VCR's cable box control feature, and your cable system scrambles all or most channels.
Hookup 4: VCR setup 1 Set the RF UNIT switch to CH 3 or CH 4, whichever channel is not used in your area. If both are used set the switch to either channel. For details, see page 87. If you made A / V connections (from page 9), you can skip this step.
Step 3: Hookups (continued) 6 The AUTO PRESET SET UP CABLE BOX SET UP starts. AUTO PRESET SET UP is done PROCESSING Please wait!!! Hookup 4: VCR Plus+ channel setup Normal display 1 Find the VCR Plus+ Channel Listing in your program guide. For details, see page 48.
Automatic clock setting To use the Auto Clock Set feature with this hookup, you need to manually select a channel that carries a time signal. 1 Tune the cable box to a channel that carries a time signal. 2 Select AUTO in the CLOCK SET menu to turn on the Auto Clock Set feature.
Step 3: Hookups (continued) Hookup 5 Pages 24 to 26 DSS (Digital Satellite System) receiver Recommended Use Use this hookup if you have a DSS receiver. It allows the VCR's cable box control feature to control the channel on the DSS receiver, simplifying the recording process.
Hookup 5: VCR setup 1 Set the RF UNIT switch to CH 3 or CH 4, whichever channel is not used in your area. If both are used set the switch to either channel. For details, see page 87. If you made A / V connections (from page 9), you can skip this step.
Step 3: Hookups (continued) 5 Enter your DSS receiver code number and press SET UP CABLE BOX CURSOR . For details, see page 40. CABLE BOX CONTROL CABLE MOUSE ON OFF BOX CODE NO.
Hookup 6 Pages 27 to 31 Incompatible cable box with only a few scrambled channels, using A/B switch Recommended Use By using an A / B switch (not supplied), this hookup allows you to record both scrambled and unscrambled channels conveniently.
Step 3: Hookups (continued) Hookup 6: VCR setup 1 Set the RF UNIT switch to CH 3 or CH 4, whichever is not being used in your area. If both are used, set the switch to either channel. For details, see page 87. If you made A / V connections (from page 9), you can skip this step.
5 The TUNER PRESET menu appears. Set SET UP TUNER PRESET ANTENNA / CABLE to CABLE and press OK. ANTENNA / CABLE For details, see page 44. ANT CABLE Use to select Then push OK Push EASY SET UP to quit 6 The AUTO PRESET SET UP TUNER PRESET SET UP starts.
Step 3: Hookups (continued) Hookup 6: VCR Plus+ channel setup 1 Press MENU and select SET VCR Plus+ CHANNELS. MENU TIMER SET / CHECK TUNER PRESET CLOCK SET LANGUAGE SET VCR Plus+ CHANNELS CABLE BOX CONTROLS ADVANCED OPTIONS Use to select an item, then push OK 2 Press CURSOR to select AUTO and SMART CH MAPPING press OK.
3 Press CURSOR to select MANAL SMART CH MAPPING AUTO MANUAL Use to select Then push OK Push MENU to quit 4 Enter the program guide channel, then the cable SET VCR Plus+ CHANNELS box output channel. GUIDE CH TV CH 25 -- 3 5 Press OK. Push 0 - 9 keys to set p r o g r a m GUIDE CH 6 Press MENU.
Selecting a language You can change the on-screen display language. 1 Press MENU, then press CURSOR to LANGUAGE move the cursor to LANGUAGE and press OK. ENGLISH When using the EASY SET UP procedure, ESPANOL skip this step. FRANCAIS Use to select an item, then push OK 2 Press CURSOR to select ENGLISH, ESPANOL, or FRANCAIS, then press OK.
Setting the clock Using the Auto Clock Set feature Some TV and cable channels transmit time signals with their broadcasts. Your VCR can pick up this time signal to automatically set the clock. The Auto Clock Set feature works only if a channel in your area is broadcasting a time signal.
Setting the clock (continued) 3 Press CURSOR to select YES, then press OK. 4 To activate the Auto Clock Set function, turn off the VCR. The VCR automatically sets the clock by searching for a channel that carries a time signal and sets your time zone and Daylight Saving Time (if applicable).
If the clock is not activated 1 Follow steps 1 and 2 in "Using the Auto Clock Set feature." The AUTO CLOCK SET menu is displayed. AUTO CLOCK SET FULL AUTO YES NO Use to select Push MENU to quit 2 Press CURSOR to select NO for FULL AUTO.
Setting the clock (continued) 3 Press the CURSOR to highlight the item you want to set, then press AUTO CLOCK SET CURSOR to make the setting. FULL AUTO YES NO * For CLOCK SET CH CLOCK SET CH 1 2 3 Leave the setting to "____" to have the TIME ZONE EASTERN VCR automatically search for a channel DAYLIGHT SAVING ON that carries a time signal.
Using Manual Clock Set 1 Press MENU, then press CURSOR to move the cursor to CLOCK SET and press CLOCK SET OK. AUTO MANUAL When using the EASY SET UP procedure, skip this step. Use to select Then push OK Push MENU to quit 2 Press CURSOR to select CLOCK SET MANUAL, then press OK.
Setting the clock (continued) 3 Press CURSOR to set the month. CLOCK SET 1 / 1 / 1998 SUN 12:00 Use to select current MONTH Then push to set DAY 4 Press CURSOR to highlight the day and press CURSOR to set the day. CLOCK SET The day of the week is set automatically.
Setting up cable box control (Skip this section if you are using Hookup 2, 3, 4, or 6.) Your VCR includes a cable box control feature that allows the VCR to control most brands of cable boxes / DSS receivers via the CABLE Mouse. With cable box control, the VCR controls channels on the cable box / DSS receiver for timer recording.
Setting up cable box control (continued) 3 Press the number buttons to enter the CABLE BOX CONTROL cable box / DSS receiver code number, then CABLE MOUSE ON OFF press CURSOR . BOX CODE NO. 123 BOX OUTPUT CH CH3 Find your cable box / DSS receiver code number from the chart below.
Cable box Code numbers Cable box Code numbers Macom 044 STS 167 Magnavox 038, 043, 080 Sylvania 012 Memorex 011 T-Cable Teletext 116 Movie Time 089, 167, 214 Tandy 269 Northcoast 325 Tatung 108 Novapl.
Setting up the cable box (continued) To ensure correct operation * Place the Cable Mouse so that it hangs out over the cable box / DSS receiver front. * Do not place the cable box / DSS receiver on top of the VCR. * Position the cable box / DSS receiver away from the VCR.
Ein wichtiger Punkt beim Kauf des Geräts Sony SLV-998HF (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Sony SLV-998HF noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Sony SLV-998HF - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Sony SLV-998HF reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Sony SLV-998HF erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Sony SLV-998HF besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Sony SLV-998HF verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Sony SLV-998HF. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Sony SLV-998HF gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
