Benutzeranleitung / Produktwartung HDW-M2100 des Produzenten Sony
Zur Seite of 115
HD DIGIT AL VIDEOCASSETTE PLA YER HD W -M2100 HD W -M2100P OPERA TION MANUAL [English] 1st Edition (Revised 5).
W ARNING To prevent fire or shock hazard, do not expose the unit to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.
WARNING: THIS WARNING IS APPLICABLE FOR OTHER COUNTRIES. 1. Use the approved Power Cord (3-core mains)/Appliance Connector/Plug with earthing-contacts that conforms to the safety regulations of each country if applicable.
Table of Contents 1 Ta b le of Contents Chapter 1 Overview 1-1 Featur es ........................................................................................... 1-1 1-2 Example System Configuration .................................................
Ta b le of Contents 2 Table of Contents Chapter 7 UMID Functions 7-1 Overview of UMID Functions ....................................................... 7-1 7-2 UMID Output and Display ............................................................ 7-2 7-2-1 UMID Output Settings .
Chapter 1 Overview Chapter 1 Overview 1-1 1-1 Features Chapter 1 Overview The HDW-M2100/M2100P is a high-definition (HD) digital videocassette player based on the HDCAM format.
Chapter 1 Overview 1-2 Chapter 1 Overview 1-1 Features Basic operation buttons and jog/shuttle dial The basic buttons and jog/shuttle dial for VTR and editing operations are provided in the conventional VTR layout, ensuring continuity with conventional operating panels.
Chapter 1 Overview Chapter 1 Overview 1-3 The following conceptual diagram shows an example of use. 1-2 Example System Configuration Digital cassette BVE-series editor Tape control HDSDI/Analog compos.
Chapter 2 Location and Function of Parts Chapter 2 Location and Function of Parts 2-1 2-1 Contr ol P anels There are three control panels, as follows: •U pper control panel • Lower control panel •S witch panel Chapter 2 Location and Function of P ar ts CTL/TC TC MENU Z 59.
Chapter 2 Location and Function of Parts 2-2 Chapter 2 Location and Function of Parts 2-1-1 Upper Contr ol P anel Z BET ACAM/SP BET ACAM SX MPEG IMX Digital BET ACAM 1(9P) 2(50P) RS-232C HDCAM POWER P.
Chapter 2 Location and Function of Parts Chapter 2 Location and Function of Parts 2-3 2-1-2 Lower Contr ol P anel CTL/TC TC MENU 59.94 CTL/TC TC MENU 59.
Chapter 2 Location and Function of Parts 2-4 Chapter 2 Location and Function of Parts 1 Audio control section 1 DISPLAY FULL/FINE button Pressing this button toggles the display mode of the level meters in the audio setting display section between FULL and FINE.
Chapter 2 Location and Function of Parts Chapter 2 Location and Function of Parts 2-5 3 Audio monitor signal selection buttons (CH1 to CH4, and CUE) The buttons in the upper and lower rows select tracks to be output to the MONITOR OUTPUT L and R connectors on the connector panel or the PHONES jack on the upper control panel.
Chapter 2 Location and Function of Parts 2-6 Chapter 2 Location and Function of Parts 2-1 Contr ol P anels 4 Time data/menu display section 1 Time data display This displays indicators relating to time data and other indicators.
Chapter 2 Location and Function of Parts Chapter 2 Location and Function of Parts 2-7 DOLBY NR indicator This lights when the Dolby noise-reduction 1) circuit is functioning. Speed indication area This indicates the speed of a DMC playback. During a DMC playback, “DMC SPD” is displayed in time data display area 2.
Chapter 2 Location and Function of Parts 2-8 Chapter 2 Location and Function of Parts 2 JOG button To use the search dial for playback in jog mode, press this button, turning it on. For details of playback in jog mode, see the description of the search dial 5 .
Chapter 2 Location and Function of Parts Chapter 2 Location and Function of Parts 2-9 PREROLL REW PLAY F FWD STOP STANDBY 1 PREROLL button 8 Tape transport control section 1 PREROLL button Press this button to cue up to the preroll point (before the IN point by the time set as the preroll time) on the tape.
Chapter 2 Location and Function of Parts 2-10 Chapter 2 Location and Function of Parts q; Editing control section 1 DMC EDIT button Use this button to memorize the playback speed varied between –1 and +2 times normal speed, and carry out automatic playback or automatic editing using the memorized playback speed.
Chapter 2 Location and Function of Parts Chapter 2 Location and Function of Parts 2-11 7 LEARN button After setting a speed variation start point (STUNT IN point) and a speed variation end point (STUNT OUT point), pressing this button makes the tape start running.
Chapter 2 Location and Function of Parts 2-12 Chapter 2 Location and Function of Parts 1 Memory card slot Insert a memory card to update this unit’s firmware. You can save or load setup menu settings onto the memory card. For details on firmware update and setup menu reading/ storing, refer to the Maintenance Manual Volume 1.
Chapter 2 Location and Function of Parts Chapter 2 Location and Function of Parts 2-13 AUDIO OUTPUT CUE CH1 OUT CH2 CH3 CH4 2-2 Connector P anel 1 Analog audio output section 1 AUDIO OUTPUT CH1 to CH4 (channels 1 to 4) connectors (XLR 3-pin, male) These connectors output analog audio signals for channels 1 to 4.
Chapter 2 Location and Function of Parts 2-14 Chapter 2 Location and Function of Parts 1 REF. (reference) VIDEO INPUT connectors (BNC type) and 75 Ω termination switch Input a reference video signal. Input a three-valued (positive and negative) sync signal, a video signal with chroma burst (VBS) or a monochrome video signal (VS).
Chapter 2 Location and Function of Parts Chapter 2 Location and Function of Parts 2-15 5 Power supply section 1 AC IN connector Use the optional power cord to connect this to an AC outlet.
Chapter 2 Location and Function of Parts 2-16 Chapter 2 Location and Function of Parts TIME CODE OUT TIME CODE OUT connector 7 Time code output section TIME CODE OUT connector (XLR 3-pin, male) This outputs the playback time code.
Chapter 3 Preparations Chapter 3 Preparations 3-1 The following example shows the connections with an HDW-2000/M2000/M2000P unit as a recorder, with this unit used as a player. 75 Ω 75 Ω REMOTE 1-IN(9P) REMOTE 1-OUT(9P) HDSDI OUTPUT SDI OUTPUT 3 (SUPER) HDSDI INPUT REF .
Chapter 3 Preparations 3-2 Chapter 3 Preparations 3-1-2 Connecting Reference Signals Connect reference signals as shown below. 3-1 Connections to External De vices • SDI OUTPUT • COMPOSITE • COMPONENT REF .
Chapter 3 Preparations Chapter 3 Preparations 3-3 3-2 Setup The principal setup operations before operating this unit can be carried out using setup menus. The setup menus of this unit comprise a basic setup menu and an extended setup menu. The contents of these menus are as follows.
Chapter 3 Preparations 3-4 Chapter 3 Preparations 3-3 Superimposed Character Inf ormation When the function menu item CHARA is set to ON, the video signal output from the HDSDI OUTPUT 3 (SUPER) connec.
Chapter 3 Preparations Chapter 3 Preparations 3-5 2 Time code reader drop frame mark (for 59.94i, 29.97PsF mode only) “.”: Indicates drop frame mode “:”: Indicates non-drop-frame mode 3 VITC field mark “ ” (blank): Fields 1 and 3 (for 59.94i, 29.
Chapter 3 Preparations 3-6 Chapter 3 Preparations 3-4-1 Cassette T ypes This unit uses the following HDCAM cassettes for playback. HDCAM cassettes The unit can also play back the following cassettes.
Chapter 3 Preparations Chapter 3 Preparations 3-7 3-4-3 Pre venting Accidental Recor ding of Shot Marks To prevent shot marks from being accidentally recorded on a tape, press in the red record inhibit plug on the cassette. Large cassette Small cassette Press in the red record inhibit plug.
Chapter 3 Preparations 3-8 Chapter 3 Preparations 3-5 Using a Memory Stic k When a Memory Stick is inserted in the VTR, the file data can be stored on the Memory Stick , which enables you to share data among cameras. Note Use a Memory Stick formatted with this VTR.
Chapter 3 Preparations Chapter 3 Preparations 3-9 Notes • Prevent metallic objects or your finger from coming into contact with the terminal of the connecting section. •D o not attach any material other than the supplied label to the label space. •A ttach the label at the prescribed labeling position.
Chapter 4 Playback Chapter 4 Playback 4-1 4-1 Playback This section describes playback of video and audio. 4-1-1 Preparations for Playback Switch and menu settings Z CTL/TC TC MENU 59.94 Audio monitor signal selection buttons (see page 2-5) : Select the audio channel(s) to be monitored.
Chapter 4 Playback 4-2 Chapter 4 Playback 4-1 Playback Time data selection Displayed time data Use the CTL/TC setting in function menu HOME page to select one of CTL (control), time code, and user bit values. When you select time code, the data displayed is determined by the F6 (TCR) setting (LTC/AUTO/ VITC) in function menu page 1 as follows.
Chapter 4 Playback Chapter 4 Playback 4-3 Playback in jog mode In jog mode, you can control the speed of playback by the speed of turning the search dial. The playback speed range is ±1 times normal speed. The playback speed range can be ±3 times normal speed by changing the setting of setup menu item 116.
Chapter 4 Playback 4-4 Chapter 4 Playback 4-1 Playback To return to normal-speed playback Press the PLAY button. To alternate between normal-speed playback and shuttle mode playback Set the search dia.
Chapter 4 Playback Chapter 4 Playback 4-5 To perform continuous capstan override playback 1 Set setup menu item 111 (TSO PLAY) to TSO. 2 Hold down the DMC EDIT button and turn the MULTI CONTROL knob to select the playback speed.
Chapter 4 Playback 4-6 Chapter 4 Playback 4-1 Playback Storing a varying playback speed in memory To store the playback speed for DMC playback, use the following procedure.
Chapter 4 Playback Chapter 4 Playback 4-7 3 Press the search dial or the SHUTTLE button or VAR button to enter shuttle/variable speed mode. The SHUTTLE/VAR indicator lights.
Chapter 4 Playback 4-8 Chapter 4 Playback To start playback immediately after preroll Press the LEARN button. The LEARN button lights, and after preroll, DMC playback is carried out for the section from the speed variation start point, then playback continues at normal speed from the speed variation end point.
Chapter 5 Shot Mark Function Chapter 5 Shot Mark Function 5-1 This unit allows the use of shot marks. Shot marks are indications at desired points on a tape which enable faster cuing. Types of shot mark On this unit, you can write post marks by a button operation during playback, while stopped, or during a search.
Chapter 5 Shot Mark Function 5-2 Chapter 5 Shot Mark Function This section describes the settings in the shot mark operation menu. Displaying the shot mark operation menu With the function menu HOME page showing in the menu display, hold down the MARK button, and press the F5 (MENU) button.
Chapter 5 Shot Mark Function Chapter 5 Shot Mark Function 5-3 This section describes the operations concerning reading and writing shot marks. Note that the following operations cannot be carried out by remote control. 5-3-1 Reading Shot Marks To read in shot marks With a cassette loaded, hold down the LIST button and press the F FWD or REW button.
Chapter 5 Shot Mark Function 5-4 Chapter 5 Shot Mark Function Z ENTRY button LIST button 5-3 Shot Mark Operations 5-3-3 Shot Mark List Operations Displaying the shot mark list Hold down the ENTRY button and press the LIST button. All of the shot mark types for which item G02 in the shot mark operation menu is set to “ON” appear in the list.
Chapter 5 Shot Mark Function Chapter 5 Shot Mark Function 5-5 A virtual shot mark appears on the monitor as “V- MARK xxx” (xxx is the number). This is not written to the tape. After entering a virtual shot mark, if you change the cassette or power the unit off, it appears in the list as the first shot mark of the next group read in.
Chapter 5 Shot Mark Function 5-6 Chapter 5 Shot Mark Function 5-3 Shot Mark Operations 1 With no shot mark list displayed, hold the MARK button down for at least 2 seconds. The REC/ERASE indicator lights, indicating that you can rewrite or erase shot marks.
Chapter 5 Shot Mark Function Chapter 5 Shot Mark Function 5-7 Camera IDs SERIAL NUMBER 010001 DATE 1998.05.11 MODEL NAME DNW 0090 TIME 12.55.10 CASSETTE NUMBER 0095 ID1 AAAAAAAAAAAA SHOT NUMBER 0052 ID2 BBBBBBBBBBBB ID3 CCCCCCCCCCCC ID4 DDDDDDDDDDDD TCR 23:59:59:29 Recording time code First shot mark in the group NO.
Chapter 5 Shot Mark Function 5-8 Chapter 5 Shot Mark Function 5-3 Shot Mark Operations 5-3-6 Sorting Shot Marks Based on shot data recorded on the tape, you can separate the shot marks by cassette, and sort them in time code sequence. To sort the shot marks Use the following procedure.
Chapter 6 Tele-File 6-1 Chapter 6 Tele-File Chapter 6 T ele-File 6-1 Overview of T ele-File Functions Tele-File is a non-contact data carrier system. Tele-File enables data writing/reading between cassettes with memory labels and VTRs. It increases the efficiency of operations such as cuing up and playback, and source data management.
6-2 Chapter 6 Tele-File Chapter 6 Tele-File 6-2 Opening the T ele-File Menu Opening from the function menu Display page 5 of the function menu in the menu display section, and then press the F1 (TELE-F) button. The Tele-File menu opens. For details about the function menu, see Chapter 8 “Function Menu” (page 8-1).
Chapter 6 Tele-File 6-3 Chapter 6 Tele-File 6-3 T ele-File Menu 6-3-1 Clip Data Display How to read the display Monitor display Menu display section Tele-File menu indicator Indicates that the menu display section is currently displaying the Tele-File menu.
6-4 Chapter 6 Tele-File Chapter 6 Tele-File Setting display area Displays the setting of the currently selected data type, and a cursor (“ * ” or “>”). The meaning of the cursor symbols is as follows: *: Indicates that the mode is clip data display mode or attribute data display/modify mode, and that data is selected.
Chapter 6 Tele-File 6-5 Chapter 6 Tele-File Monitor display Title The title (maximum 14 characters) set in attribute data display/modify mode. Selected clip number A 4-digit number representing the number of the selected clip (with the “*” cursor).
6-6 Chapter 6 Tele-File Chapter 6 Tele-File Moving the cursor directly Regardless of the cursor’s current position, pressing one of the following buttons moves the cursor directly to the specified position in the same clip and displays the data.
Chapter 6 Tele-File 6-7 Chapter 6 Tele-File 6-3-3 Modifying Clip Data To modify clip data, put the unit into clip data display mode and then press the F2 (SELECT) button to put it into clip data modification mode (the cursor changes to “>”). The function assignments for menu items in clip data modification mode are as follows.
6-8 Chapter 6 Tele-File Chapter 6 Tele-File To add and delete clips To add clips 1 Rotate the MULTI CONTROL knob to move the “*” cursor to the position where you want to insert the clip. 2 Press the F2 (SELECT) button. The unit enters clip data modification mode.
Chapter 6 Tele-File 6-9 Chapter 6 Tele-File To set the set or modified data as other time data Press the F6 (SET TO) button and select the time data (cue point, IN point, or OUT point), and then press the F5 (SET) or F6 (SET NL) button. The position where the data is set differs as follows, depending on the button pressed.
6-10 Chapter 6 Tele-File Chapter 6 Tele-File To make comment settings Proceed as follows to make comment settings. 1 Select a clip. 2 Select comment. 3 Press the F2 (SELECT) button. The unit enters clip data modification mode. 4 Press the F2 (MODIFY) button.
Chapter 6 Tele-File 6-11 Chapter 6 Tele-File 6-3-5 Displa ying and Modifying Attrib ute Data You can display and modify attribute data. The example below shows attribute data displayed on the monitor. Video final recording date The most recent date (year/month/day) on which video was recorded on the tape.
6-12 Chapter 6 Tele-File Chapter 6 Tele-File To modify attribute data You can modify the title, ID, administrator data, and write inhibit setting attributes. However, the attributes cannot be modified when the control mode is “remote.” The modification is not possible when the write inhibit setting is ON, either.
Chapter 7 UMID Functions Chapter 7 UMID Functions 7-1 Chapter 7 UMID Functions The UMID (Unique Material Identifier) is a type of meta-data in video and audio materials. It has been internationally standardized in SMPTE Standard 330M. This unit supports recording and generation of UMIDs.
Chapter 7 UMID Functions 7-2 Chapter 7 UMID Functions This section explains how to output and display UMIDs. Note When the number of active scan lines for HD SDI output is set to 720P, output and displaying of UMID are not carried out.
Chapter 7 UMID Functions Chapter 7 UMID Functions 7-3 Note The function for converting unit count to UTC works only when the unit rate is 2 (24 frames), 3 (24/1.001 frames), 4 (25 frames), 6 (30 frames), or 7 (30/1.001 frames). For other unit rates, the unit rate number and unit rate are displayed in hexadecimal.
Chapter 8 Function Menu Chapter 8 Function Menu 8-1 Chapter 8 Function Menu 8-1 Overview The function menu allows you to make frequently made settings, such as selection of input video signals and time code settings.
Chapter 8 Function Menu 8-2 Chapter 8 Function Menu 8-1-2 Using the Function Menu To change a menu item setting To change a menu item setting, press the corresponding function button (F1 to F6) to display the desired setting in the lower part of the menu display.
Chapter 8 Function Menu Chapter 8 Function Menu 8-3 8-2 Function Menu Item List The function menu has the following items. HOME page a) The selection of LTC or VITC depends on the setting of F6 (TCR) in function menu page 1 . Page 1 Item Setting F4 (CTL/TC) Selects the time data to display in time data display area 1 (see page 2-6) .
Chapter 8 Function Menu 8-4 Chapter 8 Function Menu Page 2 8-2 Function Menu Item List Item Setting F1 (V.PROC) F2 (VIDEO) Sets the HD/SD video signal output level (– ∞ to +3 dB). PRESET: Regardless of manually set values, the video signal is set to the standard level.
Chapter 8 Function Menu Chapter 8 Function Menu 8-5 Page 3 Item Setting F1 (SYNC) Sets the HD output signal sync phase. Setting method With the displayed setting flashing, you can rotate the MULTI CONTROL knob to adjust the output signal sync phase across the range ±15 µs relative to this unit’s input reference signal.
Chapter 8 Function Menu 8-6 Chapter 8 Function Menu Page 4 Page 5 Item Setting F1 (CAPSTN) Selects the number of fields for capstan lock in playback. In 59.94i, 29.97PsF mode 2F: The capstan servo locks in units of 2 fields. When playing back a tape that was recorded with composite source signals, a vertical shift in the video (H shift) occurs.
Chapter 9 Setup Menus Chapter 9 Setup Menus 9-1 Chapter 9 Setup Menus This unit has the following setup menus. •B asic setup menu • Extended setup menu To access the extended setup menu, a setting on the internal SS-89 board is required. For details, refer to the Installation Manual.
Chapter 9 Setup Menus 9-2 Chapter 9 Setup Menus To display setup menus With the function menu HOME page showing in the menu display, press the F5 (MENU) button. The currently selected setup menu item is displayed in the menu display, with the menu item number flashing.
Chapter 9 Setup Menus Chapter 9 Setup Menus 9-3 To display a desired sub-item For a menu item having sub-items, you can select a desired sub-item as follows. 1 With a desired menu item selected, press the F2 (SELECT) button. The currently selected sub-item name flashes.
Chapter 9 Setup Menus 9-4 Chapter 9 Setup Menus Resetting the menu settings to their factory default values (menu item B20) To reset the current active menu settings to their factory default values, proceed as follows.
Chapter 9 Setup Menus Chapter 9 Setup Menus 9-5 Line conversion mode Use the following procedure. When setup menu item 018 ACTIVE LINE SELECT is set to 1035 Select the conversion mode in setup menu item 916 ACTIVE LINE 1035 CONVERT MODE. 1080 k 1035 (CONV): Convert the active scan lines from 1080 to 1035, without changing the aspect ratio.
Chapter 9 Setup Menus 9-6 Chapter 9 Setup Menus To recall settings from a menu bank When recalling the settings saved in one of menu banks 1 to 3, set the corresponding one of menu items B01 RECALL BANK 1 to B03 RECALL BANK 3 to ON, then press F5 (SET) button.
Chapter 9 Setup Menus Chapter 9 Setup Menus 9-7 9-3 Items in the Basic Setup Men u The basic setup menu contains the following items. In the “Settings” column of the table, the factory default settings are indicated by an enclosing box. Item number Settings 001 PREROLL TIME 0S .
Chapter 9 Setup Menus 9-8 Chapter 9 Setup Menus Item number Item name Settings 009 a) CHARACTER TYPE 011 a) CHARACTER V-SIZE SYSTEM FREQUENCY SELECT 9-3 Items in the Basic Setup Menu Determines the ty.
Chapter 9 Setup Menus Chapter 9 Setup Menus 9-9 Item number Item name Settings B01 RECALL BANK 1 Set to ON to recall menu settings from menu bank 1. B02 RECALL BANK 2 Set to ON to recall menu settings from menu bank 2. B03 RECALL BANK 3 Set to ON to recall menu settings from menu bank 3.
Chapter 9 Setup Menus 9-10 Chapter 9 Setup Menus 9-4 Items in the Extended Setup Menu 9-4 Items in the Extended Setup Men u The extended setup menu contains the following items. In the “Settings” column of the table, the factory default settings are indicated by an enclosing box.
Chapter 9 Setup Menus Chapter 9 Setup Menus 9-11 Menu items in the range 100 to 199, relating to the control panels (Continued) Item number Item name Settings 111 TSO PLAY Select whether or not to enable tape speed override mode. DIS : Disable tape speed override mode.
Chapter 9 Setup Menus 9-12 Chapter 9 Setup Menus 9-4 Items in the Extended Setup Menu Menu items in the range 100 to 199, relating to the control panels (Continued) Item number Item name Settings 119 .
Chapter 9 Setup Menus Chapter 9 Setup Menus 9-13 201 Item number Item name Settings PARA RUN 202 Menu items in the range 200 to 299, relating to the remote control interface CF FLAG (Valid only in 50i or 25PsF mode.) Select the mode for locking to the color framing sent from the remote controller.
Chapter 9 Setup Menus 9-14 Chapter 9 Setup Menus 9-4 Items in the Extended Setup Menu Menu items in the range 300 to 399, relating to editing operations Item number Item name Settings 301 VAR SPEED RA.
Chapter 9 Setup Menus Chapter 9 Setup Menus 9-15 Menu items in the range 300 to 399, relating to editing operations (Continued) Menu items in the range 400 to 499, relating to preroll 337 EXTERNAL REFERENCE SELECT 338 OUTPUT AUDIO/TC PHASE Set the audio (AES/EBU and analog) and time code output phase.
Chapter 9 Setup Menus 9-16 Chapter 9 Setup Menus 9-4 Items in the Extended Setup Menu Menu items in the range 500 to 599, relating to tape protection Menu items in the range 600 to 650, relating to the time code generator Item number Item name Settings 601 VITC POSITION SEL-1 (Invalid in 24PsF or 23.
Chapter 9 Setup Menus Chapter 9 Setup Menus 9-17 Menu items in the range 600 to 650, relating to the time code generator (Continued) 602 VITC POSITION SEL-2 (Invalid in 24PsF or 23.98PsF mode.) In 59.94i, 29.97PsF mode Select a line to insert the VITC in.
Chapter 9 Setup Menus 9-18 Chapter 9 Setup Menus 9-4 Items in the Extended Setup Menu Menu items in the range 600 to 650, relating to the time code generator (Continued) Menu items in the range 651 to 699, relating to the UMID Item number Item name Settings 621 24F STARTING TC SEL (In 50i or 25PsF mode only.
Chapter 9 Setup Menus Chapter 9 Setup Menus 9-19 Menu items in the range 700 to 799, relating to video control a) The “Y-add” function is a circuit operation to interpolate the video signal vertically during jog or variable speed playback for the purpose of reducing the vertical movement of the playback picture.
Chapter 9 Setup Menus 9-20 Chapter 9 Setup Menus 9-4 Items in the Extended Setup Menu Menu items in the range 700 to 799, relating to video control (Continued) Item number Item name Settings 709 CAV LEVEL FORMAT (Valid only in 59.94i or 29.97PsF mode.
Chapter 9 Setup Menus Chapter 9 Setup Menus 9-21 Menu items in the range 700 to 799, relating to video control (Continued) (Items 715 to 720: Settings for controlling the SD video processing system according to the menu settings.) Item number Item name 715 VIDEO GAIN CONTROL 716 CHROMA GAIN CONTROL 717 CHROMA PHASE CONTROL 718 SETUP LEVEL (59.
Chapter 9 Setup Menus 9-22 Chapter 9 Setup Menus 9-4 Items in the Extended Setup Menu Menu items in the range 700 to 799, relating to video control (Continued) Item name Settings Item number 726 H BLANKING WIDTH (Invalid in 24PsF or 23.98PsF mode.) Select the horizontal blanking width of the video output signal.
Chapter 9 Setup Menus Chapter 9 Setup Menus 9-23 Menu items in the range 800 to 899, relating to audio control Item number Item name Settings 802 DIGITAL AUDIO MUTING IN SHUTTLE MODE Set the digital audio muting conditions during shuttle playback. OFF : Not muted.
Chapter 9 Setup Menus 9-24 Chapter 9 Setup Menus 9-4 Items in the Extended Setup Menu Menu items in the range 800 to 899, relating to audio control (Continued) Menu items in the range 900 to 999, rela.
Chapter 9 Setup Menus Chapter 9 Setup Menus 9-25 Menu items in the range 900 to 999, relating to digital processing (Continued) 903 FREEZE MODE Select the freeze mode and timing. FIELD : Freeze a video field. Field may be odd or even, according to the timing.
Chapter 9 Setup Menus 9-26 Chapter 9 Setup Menus 9-4 Items in the Extended Setup Menu Menu items in the range 900 to 999, relating to digital processing (Continued) Item number Item name Settings 918 SLOW PROCESS MODE Switch the filter for increasing the vertical resolution during slow-motion playback on or off.
Chapter 9 Setup Menus Chapter 9 Setup Menus 9-27 Menu items in the range 900 to 999, relating to digital processing (Continued) Item number Item name Settings 942 V FILTER SELECT (Invalid in 24PsF or 23.98PsF mode.) Set the vertical interpolation filter coefficient for HD-SD converter output.
Chapter 9 Setup Menus 9-28 Chapter 9 Setup Menus 9-4 Items in the Extended Setup Menu Menu items in the range 900 to 999, relating to digital processing (Continued) 961 BACKGROUND COLOR (UC) (Invalid in 24PsF or 23.98PsF mode.) Set the color of the part where no material exists (background) for up-converting.
Chapter 10 Maintenance and Inspection 10-1 Chapter 10 Maintenance and Inspection 10-1 Remo ving a Cassette When T ape Slac k Occur s If tape slack occurs in the unit, it is necessary to remove the upper lid and sound baffle. This job should always be entrusted to a technician who has undergone service training.
10-2 Chapter 10 Maintenance and Inspection Chapter 10 Maintenance and Inspection 10-3 Err or Messa ges Z ALARM indicator This unit is equipped with a self-diagnosis function, and if a problem is detected, displays an error message in the time data display and on the monitor.
Chapter 10 Maintenance and Inspection 10-3 Chapter 10 Maintenance and Inspection Error Message List Code Message Description – NO COMMUNICATION Abnormality in the interface between the lower control panel (KY-464/465 board) and SYS CPU (SS-89 board) has been detected on the lower control panel side.
10-4 Chapter 10 Maintenance and Inspection Chapter 10 Maintenance and Inspection 10-4 Moisture Condensation When the unit is suddenly moved from a cold to a warm location, or used in a very humid place, moisture from the air can condense on the head-drum.
Chapter 10 Maintenance and Inspection 10-5 Chapter 10 Maintenance and Inspection 10-5 Regular Chec ks 10-5-1 Digital Hours Meter The digital hours meter can display seven items of information, in corresponding display modes, about the operational history of the unit.
10-6 Chapter 10 Maintenance and Inspection Chapter 10 Maintenance and Inspection Note Contact a Sony service or marketing representative regarding the replacement and checking of components.
Appendix Appendix A-1 Specifications General Recording format HDCAM Power requirements 100 to 240 VAC, 50/60 Hz Power consumption 2.2 A (220 W), when used without optional devices Peak inrush current .
Appendix A-2 Appendix Specifications Variable speed mode HDCAM playback: –1 to +2 times normal playback speed Digital Betacam playback: –1 to +3 times normal playback speed MPEG IMX playback: –1.
Appendix Appendix A-3 Digital Betacam playback Video Digital Audio (CH1 to CH4) Analog Audio (cue track) MPEG IMX playback Video Digital audio (CH1 to CH4) Betacam SX playback Video Digital Audio (CH1 to CH4) Bandwidth Y0 to 5.75 MHz +0.5 dB/–0.5 dB K factor R–Y/B–Y 0 to 2.
Appendix A-4 Appendix Specifications Analog Betacam playback Video Audio a) Reference level: +4 dBm Metal tape Oxide tape Frequency response (at 10 dB below reference level a) ) 50 Hz to 15 kHz +1.
Appendix Appendix A-5 AUDIO OUTPUT CH1/2/3/4 XLR 3-pin, male (4) +4 dBm at 600 Ω load, low impedance, balanced AUDIO OUTPUT (AES/EBU) CH1/2, 3/4, 5/6, 7/8 BNC (4) Complies with AES-3id-1995 CUE OUT .
Appendix A-6 Appendix Specifications Relation between HKDV-900/503 setting items and setup menu of this unit HKDV-900/503 setting items Setup menu items of this unit HD Master 740: MASTER LEVEL (HD) a.
Appendix Appendix A-7 HD/SD video output phase settings For the HD/SD video output phase setting, you can use the maintenance menu. For details, refer to the Installation Manual.
Index I-1 Index Index A AC IN connector 2-15 ALARM indicator 2-9 Analog audio output section 2-13 video input/output section 2-13 Audio control section 2-4 monitor signal output section 2-16 monitor s.
Index Index I-2 Index REMOTE 2 PARALLEL I/O(50P) connector 2-15 RESET button 2-7 REW button 2-9 RS-232C connector 2-15 indicator 2-2 S SC (function menu) 8-5 SDI OUTPUT connectors 2-14 SDTI OUTPUT con.
The material contained in this manual consists of information that is the property of Sony Corporation and is intended solely for use by the purchasers of the equipment described in this manual.
2001 HDW-M2100/M2100P (SY) 3-206-137- 15 (1) Sony Cor por ation.
Ein wichtiger Punkt beim Kauf des Geräts Sony HDW-M2100 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Sony HDW-M2100 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Sony HDW-M2100 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Sony HDW-M2100 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Sony HDW-M2100 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Sony HDW-M2100 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Sony HDW-M2100 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Sony HDW-M2100. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Sony HDW-M2100 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
