Benutzeranleitung / Produktwartung HDC-950 des Produzenten Sony
Zur Seite of 96
HD COLOR CAMERA HDC-900 HDC-900/L HDC-910 HDC-910/L HDC-930 HDC-950 HD CCD BLOCK ADAPTOR HKC-T950 INST ALLA TION AND MAINTENANCE MANUAL 1st Edition (Revised 7).
HDC-900/950 IMM ! W ARNING This manual is intended f or qualified service personnel only . T o reduce the risk of electr ic shoc k, fire or injur y , do not perf or m any servicing other than that contained in the operating instructions unless you are qualified to do so.
HDC-900/950 IMM 1 (P) CA UTION Danger of e xplosion if batter y is incorrectly replaced. Replace only with the same or equiv alent type recommended by the man ufacturer . Dispose of used batteries according to the manuf acturer ’ s instructions. V orsicht! Explosionsgefahr bei unsachgem äß em A ustausch der Batterie.
HDC-900/950 IMM For the customers in Japan For the customers in the Netherlands Voor de klanten in Nederland Hoe u de batterijen moet verwijderen, leest u in de Onderhoudshandleiding. Gooi de batterij niet weg maar lever deze in als klein chemisch afval (KCA).
1 (E) HDC-900/950 IMM Table of Contents Manual Structure Purpose of this manual ........................................................................................ 3 (E) Related manuals ............................................................
2 (E) HDC-900/950 IMM 3. Setup Menu 3-1. Setup Menu ........................................................................................... 3-1 (E) 3-2. TOP Menu .....................................................................................
3 (E) HDC-900/950 IMM Manual Structure Purpose of this manual This manual is the installation and maintenance manual of HD Color Camera HDC- 900/910/950/930 and HD CCD Block Adaptor HKC-T950 for HDC-950/930.
4 (E) HDC-900/950 IMM . . . . . “ Semiconductor Pin Assignments ” CD-ROM (Available on request) This “Semiconductor Pin Assignments” CD-ROM allows you to search for semiconductors used in B&P Company equipment. Semiconductors that cannot be searched for on this CD-ROM are listed in the maintenance manual for the corresponding unit.
1-1 (E) HDC-900/950 IMM Section 1 Installation Overview 1-1. Checking before Installation 1-1-1. Checking the ROM and Software Version When connecting the peripheral equipment in the list below to HDC-900/910/950/ 930, be sure to check that the ROM and software version on each peripheral device is corresponding to the camera to be connected.
1-2 (E) HDC-900/950 IMM 1 1 1 1 ! !/ 6 4 3 9 !, 7 8 5! ] ! [ != 1 !; !- !- 1-2. Connectors and Cables 1-2-1. Connector Input/Output Signals HDC-900/910 Connector Layout 1-2.
1-3 (E) HDC-900/950 IMM !. !; 8 !, 2 4 !/ !- !] 5 3 6! 9 7 1 !' ![ * @[ @- @= @/ ! @ @- @[ @= @] HDC-950/930 Connector Layout * : Use 4 connector by selecting PROMPTER OUT, GENLOCK IN and RET IN signals with the switch. PROMPTER OUT signal become effective when the camera is connected to CCU.
1-4 (E) HDC-900/950 IMM 1 2 3 4 7 7 7 7 7 RET CONTROL (6P FEMALE) (External view) No. Signal I/O Specifications 1 INCOM 1 IN Zi > 10 k Z MIC ON/OFF ON : GND OFF : OPEN 2 INCOM 2 IN Zi > 10 k Z M.
1-5 (E) HDC-900/950 IMM HDC-900/910 (CE) only E E L L N N 21 3 9 9 9 9 9 REMOTE (8P FEMALE) (External view) No. Signal I/O Specifications 1 TX ( + ) HDC SERIAL DATA 2 TX ( _ ) 3 RX ( + ) HDCU/MSU/RCP/.
1-6 (E) HDC-900/950 IMM B A 5 6 3 4 1 2 10 11 8 9 7 15 16 13 14 12 20 21 18 19 22 23 24 17 B A 5 6 3 4 1 2 10 11 8 9 7 15 16 13 14 12 20 21 18 19 22 23 24 17 !] !] !] !] !] VTR (26P MALE) (HDC-900/910) (External view) No. Signal I/O Specifications A NC No connection B VTR CMD GND —— GND for VTR CMD 1 GENLOCK IN Sync 0.
1-7 (E) HDC-900/950 IMM 18 36 1 19 ! ! ! ! ! LENS (36P FEMALE) (HDC-900/910) (External view) No. Signal I/O Specifications 23 RET 3 ON IN Zi > 10 k Z ON : GND OFF : High impedance 24 LENS ADRS 0 IN.
1-8 (E) HDC-900/950 IMM ! ! ! ! ! LENS (12P FEMALE) (HDC-950/930, HKC-T950) (External view) No. Signal I/O Specifications 1 RET VIDEO IN ENABLE : 0 V ENABLE DISABLE : + 5 V or OPEN 2 VTR START IN ENABLE : 0 V /STOP DISABLE : + 5 V or OPEN 3 GND —— GND for UNREG 4 AUTO SERVO OUT AUTO : + 5 V MANU : 0 V or OPEN 5 IRIS CONT OUT + 3.
1-9 (E) HDC-900/950 IMM 1 5 10 11 16 17 18 19 20 2 3 4 !; !; !; !; !; VF (20P FEMALE) (HDC-950/930) (External view) No. Signal I/O Specifications 1 S-DA TA IN/OUT TTL level 2 NC No connection 3 NC No .
1-10 (E) HDC-900/950 IMM 5 1 2 6 11 16 3 7 12 17 4 8 13 9 14 18 20 19 15 10 !, !, !, !, !, TRACKER (FEMALE) (External view) No. Signal I/O Specifications 1 TRK R (X) OUT TRACKER RECEIVE 0 dBu unbalanc.
1-11 (E) HDC-900/950 IMM 12345 6789 1 0 11 12 13 14 15 16 17 18 19 20 1-2. Connectors and Cables @[ @[ @[ @[ @[ VF (HKC-T950) (20P FEMALE) (External view) No.
1-12 (E) HDC-900/950 IMM 1-2. Connectors and Cables @] @] @] @] @] CAM BODY (HKC-T950) (26P MALE) (External view) No. Signal I/O Specifications A UNREG IN 13 V to 17 V B UNREG GND —— GND for UNREG 1 OHB H OUT 0.
1-13 (E) HDC-900/950 IMM Yellow Black White Red Red White Blue Red White Orange White Red Yellow White Black Blue Red Brown Gray Red 1-2-2. Wiring Diagrams for Cables CCA-5 Cable HDCZ Cable 1-2.
1-14 (E) HDC-900/950 IMM 1-2-3. Connection Connectors/Cables Connection made with the connector panels during instal- lation or service, should be made with the connectors/ complete cable assemblies specified in the following list, or equivalent parts.
1-15 (E) HDC-900/950 IMM RE-181 DU-104 AU-271 DAP-24 VDA-55 IF-784 SW-1045 AT-130 CN-2017 DAD-37 DPR-154 DPR-156 VA-196 CN-1998 CN-2074 RX-28 CN-2016 SW-1019 CN-2073 CN-2015 CN-1956 CN-1974 CN-1702 SG.
1-16 (E) HDC-900/950 IMM DAD-37 DPR-154 VA-196 CN-1964 SW-1027 CN-1955 CN-1951 CN-2063 MB-882 SDI-49 VDA-55 SG-268 DAP-24 RE-181 AU-271 AT-130 SW-1017 SW-1013 SW-1015 SW-1014 DPR-156 RE-188 LP-113 RX-.
1-17 (E) HDC-900/950 IMM HKC-T950 1-3. Location of Printed Circuit Boards SW-1065 SW-1066 IF-845 AT-146 LE-256 CN-2270 CN-2271 CN-2202 RE-202 CN-2265 IF-846 CN-2264 CN-2203 SW-1076 AT-147.
1-18 (E) HDC-900/950 IMM 1-4. Opening/Closing the Side Panel HDC-900/910 1. Unscrew the two lock screws of the side panel. 2. While sliding the safety lock toward the lens, open the side panel by holding the handle. 3. Close the side panel and tighten securely the lock screws of the side panel.
1-19 (E) HDC-900/950 IMM S104 S103 S1 S101 AU-271 board (A side) S102 S201 S2 S202 S301 S304 S203 S204 S303 B C D E F G A 54 3 2 1 AU CM DYN INCOM 1 INCOM 1 switch INCOM 1 MIC GAIN switch MIC GAIN DYN.
1-20 (E) HDC-900/950 IMM 1-5. Switch Setting on the Boards Ref. No. Name Contents Factory Setting S103 INCOM1 MIC GAIN + /0/ _ Select the audio level of INTERCOM1/2 to be sent to CCU.
1-21 (E) HDC-900/950 IMM 1-5. Switch Setting on the Boards * 1: The Tracker connector communicates to INCOM1 at the standard setting, yet it is communicable to INCOM2 by setting S1-1, S301-1 and S301-4 to ON.
1-22 (E) HDC-900/950 IMM DU-104 board [Reference] [Reference] [Reference] [Reference] [Reference] The switch setting on this board is valid only when connecting the RTS kit (optional) to the INTERCOM2 connector. Ref. No. Name Contents Factory Setting S1 RTS1 RTS 1/NORM/POW Selects the function of the RTS CH1 side.
1-23 (E) HDC-900/950 IMM Switch Settings Setup Menu S100-1 S100-2 S100-3 S100-4 USER * * * * * USER MENU * * * * * OPERATION PAINT MAINTENANCE FILE DIAGNOSIS CUSTOMIZE OFF OFF OFF OFF Yes Yes Yes Yes .
1-24 (E) HDC-900/950 IMM PRESET AC OUT 200VA MAX VTR DC IN AC100V PRESET AC100V PRESET AC120V PRESET AC220V~ PRESET AC230V~ PRESET AC240V~ Voltage indication seal HDC-900/910 (CE) only PRESET AC100V 1-6.
1-25 (E) HDC-900/950 IMM Screw (B4 x 20) Screws (B3 x 6) Screws (B3 x 8) Pad spacer Shoulder pat assembly 1-7. Adjusting the Position of the Shoulder Pad (HDC-950/930) The shoulder pad is factory-conf.
1-26 (E) HDC-900/950 IMM Flexible card wire Blank panel Incom panel assembly Screws Screws Screws Screws CN1 Blank panel Screws Screws Screws Screws Blank panel 1-8. Installing the Incom Panel Assembly to the Camera Backside (HDC-950/930) n When disconnecting/connecting a flexible card wire, refer to Section 1-10.
1-27 (E) HDC-900/950 IMM 1-10. Disconnecting/Reconnecting Flexible Card Wire m . Be sure to turn off the power when disconnecting and connecting the flexible card wire. To power off, be sure to disconnect the cable connected to the DC IN connector or the battery, in addition to turning off the power switch.
1-28 (E) HDC-900/950 IMM AU-271 board suffix -13 and higher (B side) R271 1 A B C D E F G 2345 1-11. Notes on Use of the RTS Kit 1-11. Notes on Use of the RTS Kit Connecting the RTS Intercom System Ki.
2-1 (E) HDC-900/950 IMM Optical contacts (white) Insert the shorter nose end Shock absorber portion Handle 2-1. Cleaning of Connector/Cable It is recommendable to clean the optical contact portions mentioned below before connecting this unit to the camera control unit.
2-2 (E) HDC-900/950 IMM Optical contacts (white) Alignment sleeve 2. When the turn stops, pull out the remover in the straight line forcedly. n The alignment sleeve can be removed/reinstalled with the sleeve itself attached to the tip of the remover. Great care should be taken so as not to lose or damage the alignment sleeve.
2-3 (E) HDC-900/950 IMM Precision P2.6 x 5 Precision P2.6 x 5 Precision P2.6 x 5 Top chassis cover assembly Fan grill holder Fan grill Precision P2.6 x 5 2-2. Cleaning the Vent Portion of the Fan (HDC-950/930 only) A part for preventing from dust is attached in the vent portion of the fan.
2-4 (E) HDC-900/950 IMM 2-3. Replacing the Fuse w The fuse is critical for safely operating. Do exchange with the fuses authorized by the manufacturer, otherwise a fire and electric shock may occur.
2-5 (E) HDC-900/950 IMM 2-4. Recommended Replacing Parts No. Description Sony Part No. 1 KNOB (DIA 3) ASSY, VOLUME X-3167-563-X 2 KNOB, VOLUME (DIA 6) 3-185-872-0X 3 KNOB, VOLUME 6 3-602-483-0X 4 SHIE.
2-6 (E) HDC-900/950 IMM 3 1 !/ ![ 9 != !- 4 8 1 2 7 5 6 1 No. Description Sony Part No. 5 CAP, CONNECTOR (CCZ) 3-612-791-0X 6 CAP, TRK 3-626-974-0X 7 CUSHION, FAN 3-627-210-0X 8 BUSHING, RUBBER 3-627-.
2-7 (E) HDC-900/950 IMM 2-4. Recommended Replacing Parts 2-4-3. HKC-T950 Following parts are recommended replacing parts. Besides, the parts made of rubber used for this adaptor may become cracked and split with the lapse of time, therefore also replace it if necessary.
.
3-1 (E) HDC-900/950 IMM 3-1. Setup Menu The setup menu is used for selecting various setting values, items displayed on the viewfinder screen, the method of displaying, and adjustments. The menu is displayed on the viewfinder screen. The menu can also be displayed by connecting an external monitor to the TEST OUT connector.
3-2 (E) HDC-900/950 IMM 3-1. Setup Menu Switches (HDC-900/910) DISPLAY switch ON : Displays characters and messages indicating the settings and operating status of the unit on the viewfinder screen. OFF : Turns off all the displays on the viewfinder screen.
3-3 (E) HDC-900/950 IMM 3-1. Setup Menu DISPLAY switch MENU switch Rotary Encoder Switches (HDC-950/930) DISPLAY switch ON : Displays characters and messages indicating the settings and operating status of the unit on the viewfinder screen. OFF : Turns off all the displays on the viewfinder screen.
3-4 (E) HDC-900/950 IMM 3-2. TOP Menu 3-2. TOP Menu The TOP menu is provided for indicating the whole configuration of the menu items. Displaying the TOP menu HDC-900/910 : Set the DISPLAY switch from “OFF” to “MENU” while pressing the MENU SELECT switch toward the “ENTER” side.
3-5 (E) HDC-900/950 IMM 3-3. OPERATION Menu The OPERATION menu consists of the items that a camera operator can set when using this camera, such as VF screen display setting.
3-6 (E) HDC-900/950 IMM AUTO IRIS page Item Setting Initial values WINDOW 1, 2, 3, 4, 5, 6 1 OVERRIDE _ 99 to 99 0 BATT ALARM page Item Setting Description DC IN LITHIUM, DIGITAL, AC ADP TYPE c) OTHERS1, OTHERS2, AC ADP BEFORE END d) _ END d) _ c) Setting of this item is disabled in HDC-900/910.
3-7 (E) HDC-900/950 IMM 3-4. PAINT Menu The PAINT menu contains overall general paint adjustment items, such as white adjustment. For details, refer to the operation manual supplied with this unit. SW STATUS page Item Setting Description FLARE ON, OFF Sets the flare correction circuit to ON or OFF.
3-8 (E) HDC-900/950 IMM VIDEO LEVEL page Item Setting Description WHITE _ 99 to 99 Adjusts the white level of R, G, B. BLACK _ 99 to 99 Adjusts the black level of R, G, B and master. FLARE _ 99 to 99 Adjusts the flare level of R, G, B and master. GAMMA _ 99 to 99 Adjusts the gamma correction curve of the R, G, B and master.
3-9 (E) HDC-900/950 IMM GAMMA page Item Setting Description LEVEL _ 99 to 99 Adjusts the gamma correction curve of the R, G, B and master. COARSE 0.35 to 0.90 Sets the correction curve of the master gamma in 0.05 steps. TABLE STANDARD, Selects the gamma table.
3-10 (E) HDC-900/950 IMM BLK GAMMA page Item Setting Description RGB LEVEL _ 99 to 99 Adjusts the black gamma of the R, G, B and master. RGB RANGE 1, 2, 3, 4 Sets the upper limit of the video level which the RGB black gamma affects. ON, OFF Sets the RGB black gamma correction function to ON or OFF.
3-11 (E) HDC-900/950 IMM SATURATION page (Displays ROM Version 1.30 or higher) Item Setting Description SATURATION a) _ 99 to 99 Sets the saturation. ON, OFF Sets the saturation function to ON or OFF. LOW KEY SAT _ 99 to 99 Sets the saturation of the dark part.
3-12 (E) HDC-900/950 IMM (Display is initial values.) <KNEE> [R] [G] [B] [M] POINT : 0 0 0 0 SLOPE : 0 0 0 0 WHT CLP: 0 0 0 0 KNEE SAT LEVEL 0 KNEE : ON KNEE SAT: OFF WHT CLIP: ON TEST : OFF <.
3-13 (E) HDC-900/950 IMM <DETAIL 1> [M] [WHT][BLK] LEVEL : 0 LIMITER : 0 0 0 CRISPEN : 0 HV RATIO : 0 FREQ : 0 LVL DEP : 0 DETAIL : ON LVL DEP : ON (Display is initial values.) DETAIL 1 page Item Setting Description LEVEL _ 99 to 99 Sets the general level of the detail signal.
3-14 (E) HDC-900/950 IMM SKIN DETAIL page Item Setting Description SKIN DTL ON, OFF When this setting is ON, the setting [1] of the channel 1 is always set ON. Sets the skin detail function to ON or OFF. SKIN GATE b) ON, OFF Sets the zebra indication of the skin tone detail portion to ON or OFF.
3-15 (E) HDC-900/950 IMM USER MATRIX page Item Setting Description R-G, R-B, _ 99 to 99 Sets the linear matrix coefficient for each R-G, R-B, G-R, G-B, B-R, G-R, G-B, _ 99 to 99 and B-G. B-R, B-G, _ 99 to 99 MATRIX a) ON, OFF Sets the linear matrix correction function to ON or OFF.
3-16 (E) HDC-900/950 IMM MULTI MATRIX page Item Setting Description PHASE 0, 23, 45, 68, 90, Sets the angle that varies the multi matrix correction function. 113, 135, 158, 180, (sixteen-axis mode) 203, 225, 248, 270, 293, 315, 338 HUE _ 99 to 99 Adjusts the color phase the multi matrix correction function affects in every sixteen-axis mode.
3-17 (E) HDC-900/950 IMM SHUTTER page Item Setting Description SHUTTER ON, OFF Sets the shutter/ECS mode to ON or OFF. Table below a) Sets the shutter speed. (The selectable shutter speed varies with each format.) ECS FREQ Table below b) Sets the ECS frequency.
3-18 (E) HDC-900/950 IMM SCENE FILE page Item Setting Description 1, 2, 3, 4, 5 Saves and calls the scene file (the data painted in accordance with the shooting scene.) (Same as the SCENE FILE page in the FILE menu.) STORE STANDARD Returns the current paint adjustment amount and switch settings to the reference values.
3-19 (E) HDC-900/950 IMM 3-5. MAINTENANCE Menu This menu consists of paint items used less frequently such as shading adjustment and items required for the camera maintenance such as system change. AUTO SETUP page Item Setting Description AUTO BLACK * 1 Starts the automatic black balance adjustment.
3-20 (E) HDC-900/950 IMM BLACK SHADING page Item Setting Description V SAW R/G/B _ 9 9 to 99 Adjusts the black shading V SAW correction amount of the R,G,B master. V PARA R/G/B _ 99 to 99 Adjusts the black shading V PARA correction amount of R,G,B. H SAW R/G/B _ 99 to 99 Adjusts the black shading H SAW correction amount of R,G,B.
3-21 (E) HDC-900/950 IMM AUTO IRIS page Item Setting Description AUTO IRIS b) ON, OFF Sets the auto iris function to ON to OFF. WINDOW 1, 2, 3, 4, 5, 6 Selects the auto iris window. a) OVERRIDE _ 99 to 99 Sets the reference value of the auto iris level by ± 2 focus.
3-22 (E) HDC-900/950 IMM <SDI> PROMPTER : OFF BNC SDI OUT: OFF <OUT PUT> PROMPTER : OFF BNC SDI OUT: OFF LINER EXP : OFF (Display is initial values.) ROM Version lower than 1.30 ROM Version 1.30 or higher MULTI FORMAT page Item Setting Description CURRENT Displays the format being currently selected.
3-23 (E) HDC-900/950 IMM VTR 26PIN page Item Setting Description CABLE COMP OFF, 25 m, 50 m Selects the VTR (26P) cable compensation VIDEO SEL MAIN (RGB), Selects the video signal to be output to the VTR (26 p) OUT connector. MAIN (YPbPr), RET (YPbPr) outputs the return video signal input from the camera RET (YPbPr) a) control unit.
3-24 (E) HDC-900/950 IMM OTHERS1 page Item Setting Description FAN MODE AUTO1, Sets the fan mode. AUTO2, AUTO1 : normal mode MIN, MAX AUTO2 : silent mode MIN : minimum rotation mode MAX : maximum rotation mode H PHASE _ 3072 to 1023 Adjusts the H phase.
3-25 (E) HDC-900/950 IMM 3-5. MAINTENANCE Menu OTHERS2 page Item Setting Description MENU RESUME OPE MENU, Sets the menu screen displayed when starting the menu. OFF, ALL OPE MENU : Starts to display from the page in the operation menu, which was displayed at powering off of the previous time.
3-26 (E) HDC-900/950 IMM 3-5. MAINTENANCE Menu T ADP ADJ page (Displays ROM Version 1.20 or higher) Item Setting Description VSAW OFST _ 50 ~ + 50, - - - Adjusts V SAW correction amount when HKC-T950 is connected. When HKC-T950 is not connected, this setting is disable, “ - - - ” is displayed showing invalid.
3-27 (E) HDC-900/950 IMM <OPERATOR FILE> READ (MS CAM) WRITE(CAM MS) PRESET STORE PRESET FILE FILE ID: CAM CODE DATE 3-6. FILE Menu File menu is used to operate the file such as saving the reference file. OPERATOR FILE page Item Setting Description READ * 1 Reads the operator file from the memory stick.
3-28 (E) HDC-900/950 IMM 3-6. FILE Menu SCENE FILE page Item Setting Description 1, 2, 3, 4, 5 Saves and calls the scene file (the data painted in accordance with the shooting scene.) (Same as the SCENE FILE page in the PAINT menu.) STORE STANDARD Returns the current paint adjustment amount and switch settings to the reference values.
3-29 (E) HDC-900/950 IMM REFERENCE page Item Setting Description STORE FILE * 1 Registers the adjustment values of each item as the reference file. STANDARD * 1 Returns the data registered in the reference file to the reference value. READ (MS → CAM) Reads out reference file from the memory stick to the memory of camera unit.
3-30 (E) HDC-900/950 IMM LENS FILE page Item Setting Description STORE FILE * 1 Registers the adjustment values for each item (exc. the center marker position) as the lens file. No. 1to 16 Selects the file matching with the mounted lens from the sixteen lens files NAME Displays the lens file name in accordance with the No.
3-31 (E) HDC-900/950 IMM 3-6. FILE Menu FILE CLEAR page Item Setting Description PRESET * 1 Returns the preset value of the operator file set by the user to the OPERATOR original value at factory setting. REFERENCE (ALL) * 1 Returns each adjustment value registered in the reference file to the original values at factory setting.
3-32 (E) HDC-900/950 IMM 3-7. DIAGNOSIS Menu 3-7. DIAGNOSIS Menu The DIAGNOSIS menu displays the self-diagnosis of every plug-in board and photo-receptive condition of the optical connector, etc.
3-33 (E) HDC-900/950 IMM <BOARD STATUS> ROM:V1.00 OHB :OK SG :OK VA :OK AT :OK DPR :OK AU :OK VDA :OK RE :OK DAD :OK PS :OK SDI :OK DAP :OK BOARD STATUS page Item Setting Description ROM Indicates the ROM version for IC1/AT-130 board OHB OK, NG Displays the self-diagnosis status of the CCD block.
.
HDC-900/950 IMM 4-1 (E) Section 4 File System The HDC-900/910/950/930 are equipped with various file systems for managing data. 4-1. File Structure The following six types of files are available. 1. Operator File Stores the items displayed on the viewfinder and switch settings for camera operator.
4-2 (E) HDC-900/950 IMM Camera unit Preset storing (Step 4) Storing (Step 1) Reading (Step 2) Preset initialization (Step 5) Preset reading (Step 3) Current Operator File Data Output to hardware Memory stick Preset Operator File Preset factory-set value Fig.
HDC-900/950 IMM 4-3 (E) 4-3. Preset Operator File 4-3. Preset Operator File The preset operator file is designed to store the standard values of the operator file items. There are two ways of calling the preset operator file; calling from the setup menu or reading at power ON.
4-4 (E) HDC-900/950 IMM 4-4. Registering the Scene File 4-4. Registering the Scene File The scene file is used for storing temporary video adjustment values according to the scene. 5 files can be stored and the data will be stored in the camera and memory stick.
HDC-900/950 IMM 4-5 (E) 4-4. Registering the Scene File Storing the Scene File to the Memory Stick (Refer to step 1 of Fig. 4-3.) The scene file stored in the camera unit is stored to the memory stick. Set the setup menu as follows. Reading the Scene File from the Memory Stick (Refer to step 3 of Fig.
4-6 (E) HDC-900/950 IMM 4-5. Registering Reference Files 4-5. Registering Reference Files This file can be stored and read using the setup menu or MSU (master setup unit). Only one file can be stored, and will be stored in the camera and memory stick.
HDC-900/950 IMM 4-7 (E) 4-5. Registering Reference Files Reading the Reference File from the Memory Stick (Refer to step 3 of Fig. 4-4.) During the file storing, the reference files which have been stored in the memory stick at the same time are read and the reference files in the camera can also be changed.
4-8 (E) HDC-900/950 IMM Initializing Only Specified Items Using the Setup Menu (Refer to step 4 of Fig. 4-4.) References files for specified items can be initialized using the setup menu.
HDC-900/950 IMM 4-9 (E) 4-6. Registering the Lens File 4-6. Registering the Lens File The white shading which occurs when the extender is turned on, flare balance, white balance, F value of the open edge of the lens, name, etc. can be stored. Up to 16 files can be stored.
4-10 (E) HDC-900/950 IMM 4-7. Registering the OHB File 4-7. Registering the OHB File The OHB file is used for storing the maintenance adjustment values of the CCD block and the data will be stored in the camera. The data can be stored using the setup menu or the MSU (master setup unit).
HDC-900/950 IMM 4-11 (E) 4-7. Registering the OHB File 4-7-2. Adjusting the ND Offset The white balance may be slightly deviated in the ND filters. In such cases, adjust the offset. Taking the ND filter 1 white balance as the reference, the ND offset stores the deviation of the white balance of ND filter 2, 3, 4.
4-12 (E) HDC-900/950 IMM 4-8. File items 4-8. File items OPERATION menu page item OPERATOR REFERENCE SCENE OHB LENS STANDARD ( * 9) Power is Factory turned ON set 1 VF DISPLAY __ _ _ _ _ ( * 2) 2 ! IN.
HDC-900/950 IMM 4-13 (E) page item OPERATOR REFERENCE SCENE OHB LENS STANDARD ( * 9) Power is Factory turned ON set 4 BLK GAMMA Y RANGE _ __ REF _ 4 BLK GAMMA Y SW _ __ REF _ OFF 5 LOW KEY SAT _O O _ .
4-14 (E) HDC-900/950 IMM 4-8. File items page item OPERATOR REFERENCE SCENE OHB LENS STANDARD ( * 9) Power is Factory turned ON set 10 PRESET MATRIX SW _ __ REF _ OFF MATRIX SW _ __ REF _ OFF 11 MULTI.
HDC-900/950 IMM 4-15 (E) 4-8. File items page item OPERATOR REFERENCE SCENE OHB LENS STANDARD ( * 9) Power is Factory turned ON set 7 MULTI FORMAT __ _ _ _ _ _ 59.
4-16 (E) HDC-900/950 IMM 4-8. File items MSU connected only item OPERATOR REFERENCE SCENE OHB LENS STANDARD ( * 9) Power is Factory turned ON set V DTL CREATION MODE _ __ REF _ Y V DTL CONTROL MODE _ .
HDC-900/950 IMM The material contained in this manual consists of inf or mation that is the proper ty of Sony Corporation. Sony Corporation e xpressly prohibits the duplication of any portion of this .
Printed in Japan Son y Cor por ation 2003. 10 08 B&P Company ©2000 HKC-T950 (SY) HDC-900 (SY) HDC-900/L (J) HDC-910 (UCJ, CE) HDC-910/L (J) HDC-930 (SY) HDC-950 (JN, SY) J , E 3-204-338-08.
Ein wichtiger Punkt beim Kauf des Geräts Sony HDC-950 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Sony HDC-950 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Sony HDC-950 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Sony HDC-950 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Sony HDC-950 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Sony HDC-950 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Sony HDC-950 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Sony HDC-950. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Sony HDC-950 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
