Benutzeranleitung / Produktwartung DVW-A500/1 des Produzenten Sony
Zur Seite of 36
CONTROL PANEL BKDW-515 INST ALLA TION AND MAINTENANCE MANUAL 1st Edition (Revised 3) DIGITAL VIDEOCASSETTE RECORDER DVW-A500/1 DVW-500/1 DVW-A500P/1 DVW-500P/1.
BKDW-515 ! W ARNING This manual is intended f or qualified ser vice personnel only . T o reduce the risk of electric shock, fire or injury , do not perf or m any servicing other than that contained in the operating instructions unless y ou are qualified to do so.
BKD W-515 CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions. Vorsicht! Explosionsgefahr bei unsachgemäßem Austausch der Batterie.
.
1 BKDW -515 Table of Contents Manual Structure Purpose of this manual .............................................................................................. 3 Contents ...........................................................................
2 BKDW -515 4. Maintenance Menu 4-1. ROM Version .............................................................................................. 4-1 4-2. VTR Maintenance Menu .............................................................................
3 BKDW -515 Manual Structure Purpose of this manual This Manual describes the installation instructions for the digital videocassette recorder DVW-A500/1, 500/1, A500P/1, 500P/1 and the Control panel BKDW-515. This manual contains the information necessary when supplying and installing the unit, assuming use by system/service engineers.
4 BKDW -515 Relative manuals Besides this “Installation and Maintenance Manual”, the following manuals are available. • Operation Manual (Supplied with the VTR or the BKDW-515) This manual is necessary for application and operation of the VTR.
1-1 BKDW -515 n The BKDW-515 cannot be installed in the BKDW-511 Control Panel Case. for DVW-A500/1, DVW500/1, DVW-A500P/1, DVW-500P/1 1-1. Installation of Control Panel 1. Fix a dummy panel for shipping use at 90 degrees. 2. Loosen the two black screws on the dummy panel.
1-2 BKDW -515 4. While pushing the loosened black screws in the direction of the arrow, remove the lower control panel assembly from the arms. 5. Remove the screws as shown in Figure, and remove both side arms. 6. Install the arms supplied with BKDW-515.
1-3 BKDW -515 Sub panel cover Screw (BVTT3 x 6) Screw (BVTT3 x 6) 1-4. Installation of Sub Panel Cover and Switch Cover 1. Install the sub panel cover supplied with BKDW-515 to sub control panel. 2. Install the switch cover supplied with BKDW-515 to system set-up panel.
1-4 BKDW -515 1-6. Installation Space Notes on Installation on Cart Machine . When the digital Betacam recorder is to be mounted on the LMS, you can install not the control panel BKDW- 515 but the BKDW-514 to the recorder. . When the digital Betacam recorder is to be mounted on the FLEXICART, you can install both of BKDW-514/ 515 to the recorder.
1-5 BKDW -515 1-8. Extension of Control Panel To extend the BKDW-515, prepare the following BKDW- 510 (Control Panel Extension Kit), AC adapter and the connector box. Parts Required . 10m Extension Cable (BKDW-510) . AC Adapter Sony Part No.: 1-473-822-11 .
1-6 BKDW -515 1-8. Extension of Control Panel Notes when connecting the two BKDW-515 . Setup Setting Data The Current Setup setting data inside of the BKDW-515 is transferred to the VTR just after the communication between the BKDW-515 and VTR are established.
2-1 BKDW -515 SW-749 CP-266 PTC-69 KY-330 Section 2 Service Information 2-1. Location and Function of Printed Circuit Boards Board Name Circuit Function CP-266 Panel Control CPU, EL Control, PIO, Memo.
2-2 BKDW -515 BT1 inserted into a socket in IC113 (memory for storing setup data and cue data) on the CP-266 board is a battery for memory backup. m . Replace a battery for memory backup every seven years. . Store all the setup data (cue data if necessary) in a memory card before replacing the Battery for memory backup.
2-3 BKDW -515 Screws (PSW3 x 10) EL panel CP266 CN7 Screws (PSW3 x 10) Cover Screws(BVTT3 x 6) SW-749 CN1 Screws (BVTT3 x 6) Screws (BVTT3 x 6) Screw (BVTT3 x 6) Screw (BVTT3 x 6) Screw (BVTT3 x 6) 2-3. EL Panel Replacement 1. Turn off the power switch.
2-4 BKDW -515 2-4. Error Message 2-4-1. Operation when Checksum Error of Current Setup Data Occurs If the power switch is turned on when the current setup data on the control panel was destroyed for some trouble, message “ CURRENT setup DATA ERROR ” is displayed on the EL panel.
3-1 BKDW -515 Section 3 Setup Menu This section describes the menu ITEM-F series used during adjustment. For the operation and ITEM-H00 to ITEM-900 series, refer to the Operation Manual. 3-1. ITEM-F Series Display the ITEM-F series according to the procedure below.
3-2 BKDW -515 ITEM DATA Description No. ITEM No. DATA F13 TRACKING 0 off Select whether the tracking control operation with search dial is enabled or not CONTROL VIA 1 on during DT head playback. SEARCH DIAL This item is prepared exclusively for DT adjustment and tracking adjustments.
3-3 BKDW -515 ITEM DATA Description No. ITEM No. DATA F20 CONFI LED 0 switch The condition to light CONFI LED on the control panel is selected. STATUS 1 status 0: CONFI LED lights on when CONFI switch is set to ON. 1: CONFI LED lights on when playing back with CONFI head.
.
4-1 BKDW -515 Section 4 Maintenance Menu The self-diagnosis and adjustment of the VTR and control panel can be performed in this maintenance menu. To enter the maintenance mode Press the MAINTENANCE button while pressing the SFT key. To terminate the maintenance mode Press the HOME key.
4-2 BKDW -515 4-3. Panel Maintenance Menu The self-diagnosis of the control panel can be performed in this panel maintenance menu. To enter the panel maintenance menu Press the F7 (PANEL MAINT) key. To terminate the panel maintenance menu Press the F10 (EXIT) key.
4-3 BKDW -515 4-3-3. EL Panel Test An EL panel test is executed. The screen displayed on the EL panel appears while the F6 key is pressed. The displays changes every time the F6 key is pressed. ALL ON : All light. ALL OFF : All go off. V BAR : Displays the test pattern in a vertical line.
4-4 BKDW -515 Error Logger Screen The error logger data is superimposed on the monitor screen (output to the VIDEO OUTPUT COMPOSITE 3 connector or SERIAL V/A OUTPUT 4 connector). A maximum of 99 error data items can be stored. To display the error data items that are not displayed on the screen, turn the search dial to scroll them.
5-1 BKDW -515 BKD W -515 O VERALL SH7032 CPU FLASH ROM 4Mbit SRAM 1Mbit X4 SRAM 64Kbit +8V LED ,DIAL +12V +5V PIO MEMOR Y CARD I / F PIO PIO SOLENOID DRIVER DIAL DA T A DECODER JOG DIAL RS-422 +8V IN .
.
6-1 BKDW -515 6-1. Notes on Repair Parts 1. Safety Related Components Warning Components marked ! are critical to safe operation. Therefore, specified parts should be used in the case of replacement. 2. Standardization of Parts Some repair parts supplied by Sony differ from those used for the unit.
6-2 BKDW -515 BVTT3 x 6 B3 x 6 BVTT3 x 6 BVTT3 x 6 BVTT3 x 6 B3 x 6 B3 x 6 B3 x 6 2 4 1 3 5 6-2. Spare Parts List for VTR Ref. No. or Q’ty Part No. SP Description 1 A-8278-252-A o PANEL ASSY, DUMMY .
6-3 BKDW -515 D VW -A500/1, 500/1, A500P/1, 500P/1 6-3. Packing Materials and Supplied Accessories List for VTR For DVW-A500/1, 500/1 (UC) Ref. No. or Q’ty Part No.
6-4 BKDW -515 1 3 5 6 7 9 10 11 12 13 14 15 17 19 20 8 12 17 17 18 2 18 BVTT3 x 6 21 21 21 BVTT3 x 6 PS2.6 x 10 PSW3 x 10 PSW3 x 10 N 2.6 N 2.6 N 2.6 N 2.6 BVTT3 x 6 BVTT 3 x 6 W 2.5 SMALL BVTT 3 x 6 BVTT 3 x 6 BVTT 3 x 6 P2 x 8 P2 x 8 PTPWH 2.6 x 5 PTPWH 2.
6-5 BKDW -515 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 123 121 122 PWH2.6 x 5 BVTP3 x 8 E-4.0 BVTP3 x 8 B3 x 14 123 PWH2.
6-6 BKDW -515 6-5. Packing Materials and Supplied Accessories List for BKDW-515 Ref. No. or Q ’ ty Part No. SP Description 1pc X-3678-375-3 s SLIDER AD(R)ASSY 1pc X-3678-376-3 s SLIDER AD(L)ASSY 1pc.
The material contained in this manual consists of information that is the property of Sony Corporation and is intended solely for use by the purchasers of the equipment described in this manual.
Printed in Japan Son y Cor poration 2003. 11 08 B&P Company ©1995 DVW-A500/1 (UC) DVW-500/1 (UC) DVW-A500P/1 (CE) DVW-500P/1 (CE) BKDW-515 (WW) E 3-188-821-04 (2).
Ein wichtiger Punkt beim Kauf des Geräts Sony DVW-A500/1 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Sony DVW-A500/1 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Sony DVW-A500/1 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Sony DVW-A500/1 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Sony DVW-A500/1 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Sony DVW-A500/1 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Sony DVW-A500/1 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Sony DVW-A500/1. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Sony DVW-A500/1 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
