Benutzeranleitung / Produktwartung Aspire X3910 des Produzenten Acer
Zur Seite of 96
Acer Aspire X3910 Service Guide PRINTED IN T AIW AN Service guide files and updates are availab le on the ACER/CSD web; for more information, please refer to http://csd.
ii Revision History Please refer to the table below for the updates ma de on this service guide. Date Chapter Up dates.
iii Copyright Copyright © 2010 by Acer Incorporated. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into a n.
iv Disclaimer The information in this guide is subject to ch ange without notice. Acer Incorporated makes no representations or warranties, either e xpressed or implied, w ith respect to th e contents hereof and specifically disclaims any warrantie s of merchantability or fitness for a ny particular purpose.
v Conventions The following conventi ons are used in this manual: SCREEN MESSAGES Denotes actual messages that appear on screen. NOTE Gives additional informa tion related to the current topic. W ARNING Alerts you to any physical risk or system damage that might result from doing or not doing specific actions.
vi Service Guide Coverage This Service Guide provides you with all technica l information relating to the BASIC CONFIGURA TION decided for Acer's "glo bal" product offering.
vii Chapter 1 System Tour 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 System Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
viii System Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 CMOS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 Miscellaneous .
Chapter 1 1 Features Below is a brief summary of the computer ’s many features: NOTE: The features listed in this section is for your re ference only .
2 Chapter 1 PCI I/O • One PCI Express x16 bus slot • One PCI Express x1 bus slot I/O ports • Front • Five USB 2.0 ports • Memory S tick • Memory S tick PRO • Secure Digital (SD) Card •.
Chapter 1 3 Dimension and weight • Dimension (DxWxH) • X3300: 265 x 100 x 362 mm (with bezel) • X5300: 265 x 100 x 397 mm (with bezel) • Weight (estimate): 5.
4 Chapter 1 System Components This section is a virtual tour of th e sy stem’s interior and exterior components. Front Panel 3 4 5 6 7 8 10 9 1 2.
Chapter 1 5 No. Icon Component 1 Power button/power indicator 2 Optical drive bay door 3 Drive bay door eject button Press to open drive bay door and access the optical drive. 4 Media card re ader 5 Headphone/S peaker-out/line-ou t jack 6 USB 2.0 port s 7 Front IO cover 8 Microphone-in jack 9 CF I/II (Com pactFlash T ype I/II) slot 10 USB 2.
6 Chapter 1 Rear Panel No. Icon Component 1 Expansion slot (Photo shows graphics card and TV tuner card) 2 Line-out jack 3 Microphone/speaker-out/line-in jack 4S / P D I F p o r t 5e S A T A p o r t 6 USB 2.
Chapter 1 7 Internal Components No. Compon ent 1 HDD drive 2 Optical drive 3 Expansion cards 4 Mainboard 5 Heat sink fan assembly 6 Power supply.
8 Chapter 1 System LED Indicators This section describ es the different system LED indicators. LED indicator Color LED status Description Power Green On The system has AC power and is powered on. Green Blinking The system is in standby mode. — Off System is not powered on.
Chapter 2 9 CMOS Setup Utility CMOS setup is a hardware configurat ion program built into the system ROM, called the complementary met al- oxide semiconductor (CMOS) Setup Utility . Since mo st systems are already prope rly configured and optimized, there is no need to run this util ity .
10 Chapter 2 Entering CMOS setup 1. T urn on the computer and the monitor . If the computer is already turned on, close all open applicatio ns, then restart the computer . 2. During POST , press Delete . If you fail to press Delete before POST is completed, you will need to re start the computer .
Chapter 2 11 Setup Utility Menus The Setup Main menu includes the following main setup categories. • Product Information • S tandard CMOS Features • Advanced BIOS Features • Advanced Chipset F.
12 Chapter 2 Product Information The Product Information menu disp lays basic information about the syst em. These entries are for your reference only and are not user-configurable. Parameter Description Processor T ype T ype of CPU installed on the system.
Chapter 2 13 Standard CMOS Features Parameter Description Option System Date Set the date following the weekday-month-day-year format. T i me (hh:mm:ss) Set the system time fo llowing the hour-minu te-second format. AHCI Port 0/3 Displays the status of auto detection of the AHCI device.
14 Chapter 2 Advanced BIOS Features Parameter Description Option Quick Boot Allows you to decrease the time it takes to boot the computer by shortening or skipping certain st andard booting process. Enabled Disabled Quiet Boot When enabled, the BIOS splash screen displays during startup.
Chapter 2 15 Advanced Chipset Features Parameter Description Option Intel EIST When enabled, this feature allows the OS to r educe power consumption. When disabled, the system operates at maximum CPU speed.
16 Chapter 2 Integrated Peripherals Parameter Description Option Onboard SA T A Controller Select an operating mode for the onboard SA T A. Enabled Disabled Onboard SA T A Mode Select an operating mode for the onboard SA T A.
Chapter 2 17 Power Management Setup Parameter Description Option ACPI Suspend Mode Select an ACPI state. S3 (STR) S1 (POS) Deep Power Off Mode Enables or di sables the deep power off mode. Enabled Disabled Power On by RTC Alarm Enables or disables real time clock (RTC) to generate a wake event.
18 Chapter 2 PC Health Status Parameter Description Option Smart F AN Enables or disables the smart system fan control function. Enabled Disabled CPU T emperature (PECI Mode) System T emperature CPU Fan Speed System Fan Speed CPU Core +1.1V +3.30V +5.
Chapter 2 19 Frequency/Voltage Control Parameter Description Option S pread Spectrum Enables or disables the reduction of the mainboard’s EMI. Note: Remember to disable the Spread S pectrum feature if you are overclocking. A slight jitter can introduce a temporary boost in clock speed causing the overclock ed processor to lock up.
20 Chapter 2 BIOS Security Features Setting a syste m pass word 1. Use the up/down arrow keys to select a password parameter (Change Supervisor Password or Change User Password) menu then press Enter . A password box will appear . 2. T ype a password then press Enter .
Chapter 2 21 Removing a system password 1. Use the up/down arrow keys to select password parameter (Change Supervisor Password or Change User Password) menu then press Enter . 2. Enter the current p assword then press Enter . 3. Press Enter twice without entering anythin g in the password fields.
22 Chapter 2 Load Default Settings The Load Default Settings menu allo ws you to load the default settings for all BIOS setup parameters. Setup defaults are quite demanding in terms of resources cons umption.
Chapter 2 23 Save & Exit Setup The Save & Exit Setup me nu allows you to save change s made and close the Setup Utility . CMOS Setup Utility ► ► Standard CMOS Features ► Advanced BIOS Fe.
24 Chapter 2 Exit Without Saving The Exit Without Saving menu allows you to discard changes made and close the Setup Utility . CMOS Setup Utility ► ► Standard CMOS Features ► Advanced BIOS Featu.
Chapter 2 25 BIOS Recovery AMIBIOS8 supports a "recovery flash" mode, which can be used to flash update a BIOS from the boot block. This is used to update a BIOS i mage without the need to boot to an o perating system. The following is the process that user should fol low to flash BIOS ROM.
26 Chapter 2.
Chapter 3 27 This chapter contains step-by-step procedure s on how to disassem ble the desktop computer for ma intenance and troubleshooting. Disassembly Requirements T o disassemble the computer , yo.
28 Chapter 3 Pre-disassembly Procedure Before proceeding with the disassembly proce dure, perform the steps listed below: 1. T urn off the system and all the peripherals conne cted to it. 2. Unplug the power cord from the power ou tlets. 3. Unplug the power cord from the system.
Chapter 3 29 Main Unit Disassembly Screw List Screw Part No. A #6-32 L5 BZN 86.00J07.B60 B #6-32 L6 NI 86.00J44.C60 C #6-32*3/16 NI 86.1A324.5R0 D M3xL5 BZN 86.
30 Chapter 3 Removing the Side Panel 1. Perform the pre-disassembly pr ocedure descri bed on page 28. 2. Remove the two screws (A) located on the rear edge of the side panel. 3. Slide the side panel toward the back of the chassi s until the tabs on the cover disengage with the sl ots on the chassis.
Chapter 3 31 Removing the Front Bezel 1. Remove the side panel. Refer to the previous section for instructions. 2. Remove the front bezel. (1). Release the front bezel retention tabs from the chassi s interior . (2). Detach the bezel slightly away from the chassis.
32 Chapter 3 Removing the Heat Sink Fan Assembly W ARNING: The heat sink becomes ve ry hot when the syste m is on. NEVER touch the heat sink with any metal or with your hands. 1. See “Removing the Side Panel” on page 30. 2. See “Removing the Front Bezel” on page 31.
Chapter 3 33 Removing the Processor IMPORT AN T : Before removing a processor from the mainboard, make sure to create a backup file of all import ant data. W ARNING: The processor becomes very hot when the system is on. Allow it to co ol off first before handling.
34 Chapter 3 Removing the Optical Drive 1. See “Removing the Side Panel” on page 30. 2. See “Removing the Front Bezel” on page 31. 3. See “Removing the Heat Sink Fan Assembly ” on page 32. 4. See “Removing the Processor” on page 33. 5.
Chapter 3 35 (3). Lift the HDD-ODD bracket and turn it over . (4). Disconnect the data and power cab les from the HDD. (5). Remove the HDD-ODD bracket.
36 Chapter 3 7. Remove the two screws (C) from the optical drive. 8. Slide the optical drive out of the drive bay . Screw (Quantity) Color To r q u e Part No.
Chapter 3 37 Removing the Hard Disk Drive 1. See “Removing the Side Panel” on page 30. 2. See “Removing the Front Bezel” on page 31. 3. See “Removing the Heat Sink Fan Assembly ” on page 32. 4. See “Removing the Processor” on page 33. 5.
38 Chapter 3 Removing the Power Supply 1. See “Removing the Side Panel” on page 30. 2. See “Removing the Heat Sink Fan Assembly ” on page 32. 3. See “Removing the Processor” on page 33. 4. See “Removing the Optical Drive” on page 34. 5.
Chapter 3 39 7. Remove the three screws (A) that secure the power supply to the rear panel. 8. Lift the power supply module out of the chassis. Screw (Quantity) Color To r q u e Part No.
40 Chapter 3 Removing the Memory Modules IMPORT AN T : Before removing any DIMM from the memory board, make sure to create a backup file of all import ant data. 1. See “Removing the Side Panel” on page 30. 2. See “Removing the Front Bezel” on page 31.
Chapter 3 41 Removing the TV Tuner Card 1. See “Removing the Side Panel” on page 30. 2. Remove the screw (A) that secu res the card to the chassis. 3. Gently pull the card to remove it from the mainboard. Screw (Quantity) Color To r q u e Part No.
42 Chapter 3 Removing the VGA Card 1. See “Removing the Side Panel” on page 30. 2. Remove the screw (A) that secu res the card to the chassis. 3. Gently pull the card to remove it from the mainboard. Screw (Quantity) Color To r q u e Part No. #6-32 L5 BZN (1) Black 5.
Chapter 3 43 Removing the Front I/O and Card Reader Boards 1. See “Removing the Side Panel” on page 30. 2. See “Removing the Front Bezel” on page 31. 3. See “Removing the Heat Sink Fan Assembly ” on page 32. 4. See “Removing the Processor” on page 33.
44 Chapter 3 8. Remove the front I/O and card reader board bracket. (1). Remove the screw (B) that secure s the bracket to the chassis. (2). Remove the bracket. 9. Remove the card reader board. (1). Remove the two screws (B) that secure the card reader board to the bracket.
Chapter 3 45 (2). Pull the card reader board out of the bracket. 10. Remove the front I/O board. (1). Remove the two screws (B) that secu re the I/O board to the bracket. (2). Pull the I/O board out of the bracket. NOTE: The card has been hig hlighted with a yellow rectangle as above image shows.
46 Chapter 3 Removing the Mainboard 1. See “Removing the Side Panel” on page 30. 2. See “Removing the Front Bezel” on page 31. 3. See “Removing the Heat Sink Fan Assembly ” on page 32. 4. See “Removing the Processor” on page 33. 5. See “Removing the Optical Drive” on page 34.
Chapter 3 47 12. Remove the screw (D) on the rear panel. 13. Lift the board from the chassis. Screw (Quantity) Color To r q u e Part No. M3xL5 BZN (1) Black 5.5 to 6.5 kgf-cm 86.5A5B6.012 NOTE: The mainboard has been highlighted with a yellow rectangle as above image shows.
48 Chapter 3.
Chapter 4 49 This chapter provides instructions on how to troubleshoot system hardw are problems. Hardware Diagnostic Procedure IMPORT AN T : The diagnostic tests described in this chapter ar e o nly intended to test Acer p roducts. Non-Acer products, prototype cards, or modified opti ons can give false errors an d invalid system responses.
50 Chapter 4 System Check Procedures Power System Check If the system will power on, skip this sect ion. Refer to System Extern al Inspection. If the system will not power on, do the fol lowing: q Check if the power cable is properly connected to the system and AC source.
Chapter 4 51 Checkpoints A checkpoint is either a byte or word value output to I/O port 80h. The BIOS outputs checkpoint s througho ut bootblock and Power-On Self T e st (POST) to indicate t he task the system is currently executing.
52 Chapter 4 Bootblock Recover y Code Checkpoints The Bootblock recovery code gets control when the BIOS determines that a BIOS recovery needs to occur because the user has forced the upda te or the BIOS checksum is corrupt . Refer to “BIOS Recovery” on page 25 for more information about perfo rming a BIOS recovery .
Chapter 4 53 POST Code Checkpoints The POST code checkpoints are the largest set of checkpoints during the BIOS preboot process. The following table describes the type of checkpoints th at may occur during the PO ST po rtion of the BIOS. NOTE: Please note that checkpoi nts may dif fer between different plat forms based on system configuration.
54 Chapter 4 3A Initialize RTC date/time. 3B T est for total memory inst alled in the system. Also, Check for DEL or ESC keys to limit memory test. Display to tal memory in the sy stem. 3C Mid POST initiali zation of chipset registers. 40 Detect different devices (Parallel ports, serial ports, and coprocessor in CPU, .
Chapter 4 55 DIM Code Checkpoints The Device Initialization Manager (DIM) gets control at va rious times during BIO S POST to initiali ze different system busses. The following table describes the ma in checkpo ints where the DIM module is accessed. NOTE: Checkpoints may dif fer between different platforms based on system configur ation.
56 Chapter 4 Beep Codes Beep codes are used by the BIOS to indicate a seriou s or fatal error to the end user . Beep codes are used when an error occurs before the system video ha s b een initialized. Beep c odes will be generated by the system board speaker , commonly refe rred to as the PC speaker .
Chapter 4 57 T roubleshooting POST BIOS Beep Codes Number of Beeps Description 1,3 Reseat the memory , or replace with known good modul es. 6,7 Fatal error indicating a serious probl em with the system.
58 Chapter 4 Error Messages The following tables describes the error messages that may appear during POST . Each message is listed with a detailed description of the error . Memory Boot Message Displayed Description Gate20 Error The BIOS is unable to properly control the motherboard ’s Gate A20 function, which controls access of memory over 1 MB.
Chapter 4 59 Storage Device Message Displayed Description Primary Master Hard Disk Error The IDE/A T API device configured as Primary Master could not be properly initialized by the BIOS. This message is ty pically displayed when the BIOS is trying to detect and configure IDE/A T API devices in POST .
60 Chapter 4 Virus Related 3rd Slave Drive - A T API Incompatible The IDE/A T API device configured as Slave in the 3rd IDE controller fai led an A T API compatibility test. This mess age is typically displayed when the BIOS is trying to detect and configure IDE/A T API de vices in POST .
Chapter 4 61 System Configuration Message Displayed Description DMA-1 Error Error initializing primary DMA controller . This is a fatal error , often indication a problem with syst em hardware. DMA-2 Error Error initializing secondary DMA control l er .
62 Chapter 4 CMOS Miscellaneous Message Displayed Description CMOS Date/Time Not Set The CMOS Date and/or Time are invalid. This error can be resolved by readjusting the system time in AMIBIOS Setup. CMOS Battery Low CMOS Battery is low . This message usually in dicates that the CMOS battery needs to be replaced.
Chapter 4 63 USB eModule Error Messages SMBIOS eModule Error Messages CPU eModule Error Messages MPS Table (Multi-processor) eModule Error Messages Message Displayed Description Wa r n i n g ! Unsupported USB device found and disabled! This message is d isplayed when a non-bootable USB device i s enumerated and disabled by the BIOS.
64 Chapter 4 Online Support Information This section describe s online technical support services av ailable to help yo u repair the desktop computer . If you are a distributor , dealer , ASP or TPM, please re fer your techn ical queries to your local Acer branch office.
Chapter 5 65 System Block Diagram System Block Diagram and Board Layout Chapter 5.
66 Chapter 5 Board Layout Mainboard No Code Description 1 LEDH1 Power and switch LED cable connector 2 SA T A3 SA T A 3 con nector 3 USBF3 Front USB connector 4 USBF2 Front USB connector 5 USBF1 Front USB connector 6 PCIEX1 PCI Express x16 slot 7 AUDIOF1 Front audio connector 8 PCIE1 PCI Express x1 slot 9 AUDJACK1 Audio 7.
Chapter 5 67 14 KBMSCONN1 T op: PS2 Mouse port Bottom: PS2 Keyboard port 15 PWR1 4-pin A TX power connector 16 U17 Processor socket 17 CPU F AN1 Processor fan connector 18 DIMM 1-4 DIMM slots 19 PWR2 .
68 Chapter 5 System Jumper Name Location Default Settings Clear CMOS/NVR AM JBIOS1 1-2 2-3 Normal (default) Clear CMOS/NVRAM.
Chapter 6 69 This chapter offers the FRU (Field Replaceable Unit) list in global config uratio n of the X3810/X5810 desktop computer . Refer to this chapter w henever ordering th e part s to re pair or for RMA (Return Merchandise Authorization).
70 Chapter 6 X3910 Exploded Diagram.
Chapter 6 71 No. Part Name 1 C.A LED POWER SWITCH 2E J E C T B U T T O N 3 FRONT BEZEL 4 FRONT COVER 5 IO DOOR 6 IO DOOR BKT 7 LENS POWER 8M A G N E T 1 0 * 6 * 3 9 MIDDLE BEZEL 10 ODD DOOR 1 1 ODD LI.
72 Chapter 6 X3910 FRU List Category Part Name Acer Part Number ACCESSORY REMOTE CONTROLLER REMOTE CONTROLER SMK VIST A MCE ICONIZED RC WITH 2 BA TTERIES FOR EMEA RT .1 1300.001 REMOTE CONTROLER SMK VIST A MCE ICONIZED RC WITH 2 BA TTERIES F OR US RT .
Chapter 6 73 MODEM CARD LITE-ON D-1 156E#A10A LOW-PROFILE PCI-E 56K V .92 FX.10100.003 MODEM CARD 56K PRO-NETS LSI HPE56L6 (LO FX.10100.021 MODEM CARD 56K PRO-NETS USB FX.10100.001 TV TUNER CARD PCIE SINGLE ISDB-T TU.10500.037 TV TUNER CARD YUAN PE988-D PCI TU.
74 Chapter 6 COMBO MODULE/ DVD-ROM DRIVE ODD HLDS BD COMBO SA T A HH DL 4X CH10F LF W/BRACK BEZEL SA T A KO.00605.001 ODD PIONEER BD COMBO SA T A HH DL 4X BDC-2 03RS W/BRACKET BEZEL SA T A KO.0060D.001 ODD BLU-RA Y DISC REWRITER SA T A HLDS GBW-H20N KU.
Chapter 6 75 CPU HEA TSINK AIR COOLER LGA775 TMDC6 NEW SPRIG HI.10800.028 KEYBOARD KEYBOARD PS2 104KEY CHICONY KB-07593US2552V US2552V US BLAC KB.PS203.096 KEYBOARD PS2 104KEY CHICONY KB-07593RD2552V TRADITIONAL CHINESE BLACK KB.PS203.097 KEYBOARD PS2 104KEY CHICONY KB-07593RE2552V SIMPLE CHINESE BLACK KB.
76 Chapter 6 KEYBOARD PS2 104KEY CHICONY KB-07593S32552V RUSSIAN BLACK KB.PS203.121 KEYBOARD PS2 105KEY CHIOCNY KB-07596HU2552V HUNGARIAN BLACK KB.PS203.122 KEYBOARD PS2 104KEY CHICONY KB-07593GR2552V GREEK BLACK KB.PS203.123 KEYBOARD PS2 105KEY CHICONY KB-07596DK2552V DANISH BLACK KB.
Chapter 6 77 KEYBOARD PS2 105KEY LITE-ON SK-9620 SG-30600-35W SWEDISH BLACK VIST A KB.PS2 0B.0 25 KEYBOARD PS2 105KEY LITE-ON SK-9620 SG-30600-2BW UK BLACK VIST A KB.PS2 0B.0 26 KEYBOARD PS2 109KEY LITE-ON SK-9620 SG-30600-2VW JAP ANESE BLACK VIST A KB.
78 Chapter 6 KEYBOARD USB 105KEY CHICONY KU-07606CH2552V SWISS/G BLACK KB.USB03.079 KEYBOARD USB 105KEY CHICONY KU-07606B02552V BELGIUM BLACK KB.USB03.080 KEYBOARD USB 105KEY CHICONY KU-07606IC2552V ICELANDIC KB.USB03.081 KEYBOARD USB 105KEY CHICONY KU-07606N02552V NORWEGIAN BLACK KB.
Chapter 6 79 KEYBOARD USB 105KS LITE-ON SK-9625 BLACK BELGIUM KB.USB0B.061 KEYBOARD USB 105 KEY LITE-ON SK-9625 SG-30700-2WW BLACK ICELANDIC VIST A KB.USB0B.062 KEYBOARD USB 105KS LITE-ON SK-9625 BLACK NORWEGIAN KB.USB0B.063 KEYBOARD USB 104 KEY LITE-ON SK-9625 SG-30700-XTW BLACK HEBREW VIST A KB.
80 Chapter 6 POINTING DEVICE MOUSE PS2 OPT SM-9620 LITEON SM-30600-00W MS.1 1200.017 LOGITECH 0810_PS2 OPTICAL MOUSE PS2 M-SBR-ACR2 MS.1 1200.013 MOUSE USB OPT SM-9625 LITEON SM-30700-00W MS.1 1200.018 LOGITECH 0810_USB OPTICAL MOUSE USB M-UA Y -ACR2 MS.
Appendix A 81 This section provides technica l specifications for the system. Processor Intel Core 2 Quad Item Specif ication Model number Q6600 Q8200 Q8300 Q9300 Q9400 Q9550 Q9650 Core (nm) 65 45 45 45 45 45 45 L2 cache size (MB) 8 4 4 6 6 12 12 Clock speed (GHz) 2.
82 Appendix A System Board Majo r Chip s Intel Pentium Dual-Core Item Specification Model number E2220 E 5200 E5300 E54 00 Architecture (n m) 65 45 45 45 L2 cache size (MB) 1 2 2 2 Clock speed (GHz) 2.
Appendix A 83 System Memory System BIOS Item Sp ecification Memory controller Intel G43/G45 Express chipset Memory type DDR3-1066/1333 unbuffered DIMM Module name PC 3-8500/10600 Organization ECC DIMM.
84 Appendix A Hard Disk Drive VGA Interface PCI Interface Network Interface SA T A Interface Item Sp ecification S torage contro ller NVIDIA NForce MCP73PV 10 48 BGA V endor WD Seagate HGST Model no.
85 Appendix A Audio Interface Keyboard and Input Device s Optical Drive Item Specification Audio controller Realtek ALC888S 8-channel audio CODEC Connectors Audio 7.
Appendix A 86 Read S peed DVD-R/R W/R OM(SL/DL) 10x / 8x / 16x / 12x max. DVD-R DL8x max. DVD-RAM (V er .1.0/2.2) 2x/ 3x-5x PCA V DVD+R/ + R W 1 0 x / 8 x m a x . D V D + R D L 8 x m a x . CD-R/RW/ROM 40x / 40x / 40x max. CD-DA (DAE) 40x max. 80 mm CD 10x max.
87 Appendix A DVD-ROM Item Specification V endor H LDS PL DS Model name DH10N DH-16D4S Drive type DVD-ROM DVD-ROM Write S peed — — Read S peed CD-ROM Max 52x DVD-ROM Max 16x DVD-ROM (single layer).
Appendix A 88.
Ein wichtiger Punkt beim Kauf des Geräts Acer Aspire X3910 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Acer Aspire X3910 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Acer Aspire X3910 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Acer Aspire X3910 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Acer Aspire X3910 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Acer Aspire X3910 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Acer Aspire X3910 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Acer Aspire X3910. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Acer Aspire X3910 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
