Benutzeranleitung / Produktwartung SA-001S des Produzenten SkyLink
Zur Seite of 20
Model: SA-001S User’ s Instructions W ireless External Alarm.
1 TABLE OF cONTENT INTRODUCTION ................................................................................................... INSTALLATION .............................................................................................. PROGRAMMING – LEARN REMOTE OR SENSORS OR CONTROL PANEL .
2 INTrOducTION Congratulations on purchasing the Skylink Wireless External Alarm SA-001 Series. The SA-001 Series provide you with a piercing siren and powerful features yet ease to use. You will nd the installation to be simple and be able to get the unit up and running easily.
3 - Set Compatibility Jumper: Refer to the following table to setup the Wireless External Alarm to work with different Skylink’s Security System or Sensors. To select, you will see a jumper connector marked “J2” as shown below. Use a paper clip to remove the jumper connector and re-locate to the proper posts.
4 cAuTION: The adaptor as a disconnect devices: − the socket-outlet shall be installed near the equipment and shall be easily accessible. In order for the remote or sensor or control panel to communicate with the Exter- nal Wireless Alarm properly, this need be programmed into the Wireless External Alarm previously.
5 3B – Learn motion sensor to the Wireless External Alarm: - Press and hold the Learn button on the Wireless External Alarm for 2 seconds and then release. The Learn/Set LED will ash. - Activate the motion sensor by pressing the “Test/Set” button on the motion sensor.
6 Mute button 3C – Learn door/window sensor to the Wireless External Alarm: - Press and hold the Learn button on the Wireless External Alarm for 2 seconds and then release. The Learn/Set LED will ash. - Activate the Door/Window Sensor, by separating the magnets to send the signal.
7 To erase unwanted remote(s) or sensor(s) or control panel(s) from the Wireless External Alarm will erase all learned devices from the Wireless External Alarm. - Press and hold the Learn/Set button on the Wireless External Alarm for 8 seconds. - While holding the Learn/Set button on the Wireless External Alarm until the Learn/Set LEDs turn on.
8 The Wireless External Alarm can be programmed to react 2 arming sequences when it receives the signal from the sensor. In order to arm the Wireless External Alarm, the remote (optional) must be programmed to the Wireless External Alarm.
9 - You will hear 1 beep and the LEDs will ash once indicating the Wireless External Alarm is being counted to Away mode. - After 30 seconds, you will hear 2 beeps and the LEDs will ash twice indicating the Wireless External Alarm in Away mode.
10 The Wireless External Alarm is designed to work with the Skylink security control panel such as AM-001, ML-001 and SC-001. Put the control panel that you plan to program into programming mode. Refer to the User’s Instructions of that control panel.
11 You may connect your existing alarm system with the Wireless External Alarm so that the Wireless External Alarm will be triggered by your alarm system.
12 You can enable or disable the Alert Notication. When it is set to enable, the Wireless External Alarm will beep when arm or disarm or during the entry/exit countdown period. When it is set to disable, the Wireless External Alarm will not beep when arm or disarm or during the entry/exit countdown period.
13 When the battery power is being reduced, the Wireless External Alarm will emit 3 beeps when the remote arm or disarm the unit. It is time to replace the batteries or recharge the battery pack (rechargeable battery only) as soon as the low battery signal appears.
14 Your Wireless External Alarm requires few simple maintenance to ensure its con - tinued reliability and operation. - The solar panel on the top housing should be cleaned using the soft and damp cloth. This will ensure the solar panel receives all the available light.
15 Questions Solutions Why the Wireless External Alarm does not respond to the sensors or remote? You must program the sensors or remote to the Wireless External Alarm before they can work together. Why I can’t arm my system? Make sure none of the sensors are trig- gered.
16 Fcc This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
17 WArrANTy If, within one year from date of purchase, this product should become defective (except battery), due to faulty workmanship or materials, it will be repaired or replaced, without charge. Proof of purchase and a Return Authorization Number are required.
18 cusTOmEr sErVIcE If you would like to - nd out the up-to-date specications - know more about features and applications - download documents, i.e. user’s instructions - order Skylink products or if you have difculty getting the products to work, please: 1.
19 101Y035 DEC,2012.
Ein wichtiger Punkt beim Kauf des Geräts SkyLink SA-001S (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie SkyLink SA-001S noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für SkyLink SA-001S - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von SkyLink SA-001S reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über SkyLink SA-001S erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon SkyLink SA-001S besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von SkyLink SA-001S verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit SkyLink SA-001S. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei SkyLink SA-001S gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
