Benutzeranleitung / Produktwartung Q1635 des Produzenten Axis Communications
Zur Seite of 24
AXIS Q1635 Network Camera Installation Guide.
Legal Considerations Video and audio surveillance can be regulated by laws that vary from country to country . Check the laws in your local region before using this product for surveillance purposes. This product includes one (1) H.264 decoder license and one (1) AAC decoder license.
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver .
.
AXIS Q1635 Network Camera Safety Infor mation Read through this Installation Guide carefully before installing the product. Keep the Installation Guide for future reference. Hazard Levels DANGER Indicates a hazardous situation which, if not avoided, will result in death or serious injury .
AXIS Q1635 Network Camera Safety Instructions NO NO NO TICE TICE TICE • The Axis product shall be used in compliance with local laws and regulations. • To use the Axis product outdoors, or in similar environments, it shall be installed in an approved outdoor housing.
AXIS Q1635 Network Camera WARNING • Risk of explosion if the battery is incorrectly replaced. • Replace only with an identical battery or a battery which is recommended by Axis. • Dispose of used batteries according to local regulations or the battery manufacturer's instructions.
8.
AXIS Q1635 Network Camera Installation Guide This Installation Guide provides instructions for installing AXIS Q1635 Network Camera on your network. For other aspects of using the product, see the User Manual available at www .axis.com Installation Steps 1.
AXIS Q1635 Network Camera Hardware Overview 12 1 1 13 14 15 16 5 6 7 8 9 1 0 1 4 3 2 1. Status LED indicator 2. Focus ring 3. Lock screw for focus ring 4.
AXIS Q1635 Network Camera 5. I/O connector 6. Iris connector 7. P ower connector 8. P ower LED indicator 9. Network LED indicator 1 0. RS485/RS422 connector 1 1. Network connector (P oE) 12. Control button (1) 13. Function button (2) 14. microSD Card slot 15.
AXIS Q1635 Network Camera LED Indicators LED Color Indication Green Steady for connection to a 1 00 Mbit/s network. Flashes for network activity . Amber Steady for connection to a 1 0 Mbit/s network. Flashes for network activity . Net- work Unlit No network connection.
AXIS Q1635 Network Camera Status LED Behavior for Focus Assistant Color Indication Green Focus Assistant is enabled The lens is optimally adjusted Amber The camera has been moved, or an object has been inserted in front of the lens. Exit and restart the Focus Assistant.
AXIS Q1635 Network Camera NO NO NO TICE TICE TICE Due to local regulations or the environmental and electrical conditions in which the product is to be used, a shielded network cable (STP) may be appropriate or required.
AXIS Q1635 Network Camera SD Card Slot A microSD card (not included) can be used for local recording with removable storage. For more information, see Specications on page 15 . NO NO NO TICE TICE TICE To prevent corruption of recordings, the SD card should be unmounted before removal.
AXIS Q1635 Network Camera I/O connector 4–pin terminal block for: • 0 V DC (-) • Auxiliary power (DC output) • Digital Input • Digital Output 1 2 3 4 Function Pin Notes Specications 0 V DC (-) 1 DC output 2 Can be used to power auxiliary equipment.
AXIS Q1635 Network Camera 12 V max 50 mA 1 2 3 4 Setup example: 3. I/O congured as input 4. I/O congured as output P ower Connector 2-pin terminal block for power input.
AXIS Q1635 Network Camera Audio Connector 3.5 mm audio connectors (stereo) 1 2 3 1 Tip 2 Ring 3 Sleeve Audio Input Microphone/Line in Ground Audio Output Line out (mono) Ground RS485/422 Connector Two 2-pin terminal blocks for RS485/RS422 serial interface.
AXIS Q1635 Network Camera Install the Hardware NO NO NO TICE TICE TICE Due to local regulations or the environmental and electrical conditions in which the product is to be used, a shielded network cable (STP) may be appropriate or required.
AXIS Q1635 Network Camera 1. Open the product’s home page and go to Setup > Basic Setup > Focus . 2. Under the Basic tab , click Open iris . If the button is inactive the iris is already open. 3. If focus has been set before, click Reset to reset the back focus.
AXIS Q1635 Network Camera 6. Turn the focus ring slowly counter-clockwise until the status indicator ashes green or amber (not red). 7. To exit the Focus Assistant, press the Function button again. The Focus Assistant is switched off automatically after 15 minutes.
AXIS Q1635 Network Camera Note • If you select a DC iris conguration le for a P-iris lens, an error message will appear below the iris conguration type in the Camera Settings page. For custom DC Iris lenses, select Generic DC Iris option. • There is no need to restart the product after changing the lens.
AXIS Q1635 Network Camera Visit Axis learning center www .axis.com/academy for useful trainings, webinars, tutorials and guides. Warranty Information For information about Axis’ product warranty and thereto related information, see www .
Installation Guide V er . M1.2 AXIS Q1635 Network Camera Date: December 20 14 © Axis Communications AB, 2014 P art No. 61 1 17.
Ein wichtiger Punkt beim Kauf des Geräts Axis Communications Q1635 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Axis Communications Q1635 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Axis Communications Q1635 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Axis Communications Q1635 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Axis Communications Q1635 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Axis Communications Q1635 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Axis Communications Q1635 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Axis Communications Q1635. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Axis Communications Q1635 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
