Benutzeranleitung / Produktwartung LX 2900 des Produzenten Simplicity
Zur Seite of 24
A TT A CHMENT OPERA T OR’S MANU AL 47” T wo-Sta ge Snowthr ower Mfg. No. Description 1694404 47” Two Stage Snowthrower (for use with Legacy LX / 2000 / 2900 Series) 1725463 Revision 04 Rev.
1 T able of Contents Adjustment Skid Shoe Adjustment ...................................11 T r oubleshooting, Adjustments & Service T roub leshooting Char t ...................................12 Initial Installation Install F ront Hitch ..........
2 This machine is capable to amputating hands and feet. Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of unit, severe personal injury or death to you, or bystanders, or damage to property or equipment.
3 Safety Rules 8. Always follow the engine manual instructions for stor- age preparations before storing the unit for both short and long term periods. 9. Always follow the engine manual instructions for proper start-up procedures when returning the unit to service.
4 Safety Decals SAFETY DECALS This unit has been designed and manufactured to pro- vide you with the safety and reliability you would expect from an industry leader in outdoor power equipment manufacturing.
5 Safety Information Required Accessories It is required that tire chains and two rear wheel weights or Quick Tach Weights are used. Never operate on slopes greater than 17.6% (10°). Recommended Accessories A rear-mounted weight box can also be added for additional traction.
6.
7 Operation OPERA TION Controls Read and understand the instructions in your tractor Operator’s Manual. Refer to Figure 1 for control locations. A. ELECTRIC CHUTE ROTATOR Rotates the chute right and left. B. PTO SWITCH Engages and disengages the snowthrower.
8 Operation T ranspor ting 1. Disengage the electric clutch and then raise the snowthrower. 2. Adjust ground speed according to surface conditions. 3. Select a low ground speed when transporting on a slippery surface. Engine & Ground Speed Selection Always run the engine at full throttle.
9 Maintenance Schedule For Normal Care Care Required Schedule Clean snow and ice from After each use. snowthrower. Grease Auger Zerks ** Every 25 hours & before seasonal storage Grease Drive Chain.
10 Maintenance Figure 3. Drive Shaft Lubrication Lubricate Dischar ge Chute See Figure 2. Lubricate the ring gear at the base of the discharge chute with lithium grease. Lubricate the deflector hinge, extension linkage, and cable with oil. Drive Shaft Lubrication See Figure 3.
11 Maintenance Inspect Scraper Bar 1. Raise snowthrower to highest position. 2. Use safety block(s) to secure snowthrower: a. Place safety block under attachment. b. Lower attachment until it rests on block(s). 3. Inspect location where scraper bar (A, Figure 6) meets snowthrower housing.
12 T roubleshooting Locate the problem you’ve encountered in the chart below. Check the possible causes one at a time in the order list- ed. Correct any problems that are found and operate the snowthrower to see if you have eliminated the problem.
13 Initial Installation INITIAL INST ALLA TION Follow the instructions for the subframe kit. Install Front Hitc h 1. Lift the hitch assembly (C, Figure 10) slide onto the slots on tractor (E). Lift back of hitch assembly to frame and install clevis pins (B) ,clevis pins (F) and hair pins (A).
14 Initial Installation INST ALL LONG DRIVE SHAFT 1. Slide the drive shaft (A, Figure 11) in from the front. Line up the support bracket (B) with the front hitch (C). Simultaneously line up the the locking collar of the drive shaft (A, Figure 12) with the gear drive of the transmission (B).
15 Initial Installation Figure 14. Discharge Chute Assembly A. Discharge Chute B. Plastite Screw C. Hold-Down Plate Mount Cable Guide 1. Using the 5/16-18 x 1 capscrew (C, Figure 13), lock- washer, an.
16 Initial Installation Figure 16. Install Drive Shaft A. Key B. 1/4-20 Centerlock Nut C. Set Screw D. 1/4-20 x 1-7/8 Capscrew Figure 18. Cable and Wire Routing Secure Cables DRILL REMOTE DEFLECTOR CONTROL MOUNTING BRACKET HOLES NOTE: Perform the following procedure after the snowthrower is completely installed for the first time.
17 Snowthrower Installation Figure 21. Attach Drive Shaft A. Locking Collar SNO WTHR O WER INST ALLA TION 1. Fully lower the attachment lift. 2. See Figure 19. Pull the shot pins (B) back and lock- ing them. 3. Set PTO shaft on bracket. 4. See Figure 20.
11. See Figure 23. Insert the deflector control handle (B) into the mounting bracket (C). Route the remote deflector control cable and spout rotator motor wires through the cable guide (Figure 24). Secure the handle (B, Figure 23) using a clevis pin (A) and hair pin clip (D).
19 Snowthrower & Hitch Removal SNO WTHR O WER & HITCH REMO V AL NOTE: Whenever removed, install clevis pins, hitch pins, clips and hardware onto snowthrower and hitch for stor- age. 1. Fully lower the attachment lift. 2. See Figure 21. Disconnect the drive shaft by pulling back on the locking collar (A) and then pulling the shaft off.
20 Remote Deflector Control T emplate Line Template Up with Edge of Plastic Dashboard Mark and Drill One 9/32” Hole Mount Bracket and align with Line Mark and Drill One 9/32” Hole MOUNTING REMO TE DEFLECT OR CONTR OL NOTE: Read through instructions before beginning.
21 Remote Deflector Control T emplate Line Template Up with Top Crease of Plastic Dashboard Line Template Up with Edge of Plastic Dashboard Mark and Drill One 9/32” Hole.
22 T orque Specification Chart FOR STANDARD MACHINE HARDWARE (Tolerance ± 20%) Hardware Grade SAE Grade 2 SAE Grade 5 SAE Grade 8 Size Of in/lbs in/lbs in/lbs Hardware ft/lbs Nm. ft/lbs Nm. ft/lbs Nm. 8-32 19 2.1 30 3.4 41 4.6 8-36 20 2.3 31 3.5 43 4.
MANUFACTURING, INC. 500 N Spring Street / PO Box 997 Port Washington, WI 53074-0997 www.simplicitymfg.com © Copyright 2005 Simplicity Manufacturing, Inc.
Ein wichtiger Punkt beim Kauf des Geräts Simplicity LX 2900 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Simplicity LX 2900 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Simplicity LX 2900 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Simplicity LX 2900 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Simplicity LX 2900 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Simplicity LX 2900 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Simplicity LX 2900 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Simplicity LX 2900. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Simplicity LX 2900 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
