Benutzeranleitung / Produktwartung 6RA70 des Produzenten Siemens
Zur Seite of 232
SIMOREG DC Mast er 6RA70 Series Base Dr iv e Ins tr uctions Micr oprocessor -based con v er t ers fr om 15A to 1680A f or v ar iable speed DC dr iv es Re v 6 .0 Siemens Energy & Aut omation, Inc. 3333 Old Milton Par kw ay Alphare tta, GA 30005 1-800-964-4114 seainf o@sea.
© Siemens Energy & Automation 200 6 All rights reserved Converter software version: As these Operating Instructions w ent to print, SIMOREG 6RA70 DC Mast er converters were being delivered from the factory with software version 2. 2 installed. These Operating Instructions also apply to other software versions .
Siemens Energy & Automation 0-1 SIMOREG DC Master Base Drive Panel Operating Instructions 0 Content s Page 1 Safety information 1-1 2 Introduction 2.1 Base Drive Panel Description 2-1 2.2 General Information 2-1 2.3 Rated DC Current 2-2 2.4 Card Rack Assembly 2-2 3 Parts and Service 3.
0-2 Siemens Energy & Automation SIMOREG DC Master Base Drive Panel Operating Instructions 8 Start-up 8.1 General safety information 8-1 8.2 Operator control panels 8-2 8.3 Parameterization procedure 8-4 8.4 Typical connection diagrams 8-6 8.5 Reset to factory default values 8-8 8.
Siemens Energy & Automation 0-3 SIMOREG DC Master Base Drive Panel Operating Instructions 10.24 Motorized potentiometer 10-49 10.25 Oscillation 10-51 10.26 definition of Motor Interface 10-52 10.27 Torque Shell Input 10-53 10.28 Speed limiting controller 10-54 10.
Siemens Energy & Automation 1-1 SIMOREG DC Master Base Drive Panel Operating Instructions 1 Safety information WARNING Hazardous voltages and rotating parts are present in this electrical equipment during operation. Non-observance of the safety inst ructions can result in death, severe personal injury or substantial property damage.
1-2 Siemens Energy & Automation SIMOREG DC Master Base Drive Panel Operating Instructions NOTE These operating instructions do not purport to cover all details or variations in equipment, nor to provide for every possible contingency to be met in connection with installation, operation or maintenance.
Siemens Energy & Automation 1-3 SIMOREG DC Master Base Drive Panel Operating Instructions CAUTION Electro-statically sensitive devices The converter contains electro-stat ically sensitive devices. These can easily be destroyed if they are not handled correctly.
1-4 Siemens Energy & Automation SIMOREG DC Master Base Drive Panel Operating Instructions NOTES:.
Siemens Energy & Automation 2-1 SIMOREG DC Master Base Drive Panel Operating Instructions 2 Description 2.1 Base Drive Panel Description Series 6RA70 SIMOREG DC MASTER Base Drive P anels are complete drive assemblies ready to be installed and operated.
2-2 Siemens Energy & Automation SIMOREG DC Master Base Drive Panel Operating Instructions The power section for the armature and field converters is constructed of isolated thyristor modules for converters rated from 15A to 850A at 460VAC-line voltage.
Siemens Energy & Automation 3-1 SIMOREG DC Master Base Drive Panel Operating Instructions 3 Part s and Service 3.1 Base Drive Panel Catalog Numbers US RATING (Amps DC) 1-QUAD TYPE (Catalog No.) 4-QUAD TYPE (Catalog No.) Horsepow er (240V DC 1 ) Horsepow er (500V DC) 15 6RA7013-2FS22-0 6RA7013-2FV62-0 3HP 7.
3-2 Siemens Energy & Automation SIMOREG DC Master Base Drive Panel Operating Instructions 3.2 Service Spare Parts An excellent stock of drive products spare parts is maintained at the Alpharetta, Georgia factory. Same day delivery and after hour shipments can be serv iced from this stock, including on weekends and holidays.
Siemens Energy & Automation 3-3 SIMOREG DC Master Base Drive Panel Operating Instructions 3.3 Option Part Numbers Options Order No. Terminal expansion card (CUD2) 6RX1700-0AK00 User-friendly opera.
3-4 Siemens Energy & Automation SIMOREG DC Master Base Drive Panel Operating Instructions 3.4 Spare Parts Printed Circuit Boards DESCRIPTION WHERE USED US Rating 460V PART NUMBER RECOM SPARE Micro.
Siemens Energy & Automation 3-5 SIMOREG DC Master Base Drive Panel Operating Instructions Fans/Blowers DESCRIPTION WHERE USED US Rating 460V PART NUMBER RECOM SPARE FAN, 24 VDC (C98130-A1256-C553).
3-6 Siemens Energy & Automation SIMOREG DC Master Base Drive Panel Operating Instructions Armature Converter Thyristor Modules, (for 4-Quad Drives) DESCRIPTION WHERE USED US Rating 460V PART NUMBE.
Siemens Energy & Automation 3-7 SIMOREG DC Master Base Drive Panel Operating Instructions Power Fuses Armature Converter AC Line Fuses, (1PFU - 3 PFU) DESCRIPTION WHERE USED US Rating 460V PART NU.
3-8 Siemens Energy & Automation SIMOREG DC Master Base Drive Panel Operating Instructions Field Converter AC Line Fuses (1 & 2FSFU) DESCRIPTION WHERE USED US Rating 460V PART NUMBER RECOM SPAR.
Siemens Energy & Automation 3-9 SIMOREG DC Master Base Drive Panel Operating Instructions Control Transformer (1CTR, 2CTR, 3CTR) DESCRIPTION 460 VAC Primary WHERE USED US Rating 460V PART NUMBER R.
3-10 Siemens Energy & Automation SIMOREG DC Master Base Drive Panel Operating Instructions 3.5 Standard Terms and Conditions of Sale Siemens Energy & Automation, Inc.
Siemens Energy & Automation 3-11 SIMOREG DC Master Base Drive Panel Operating Instructions 7. NONCANCELLA TION - Buyer may not cancel or terminate for convenience, or direct suspension of manufact.
3-12 Siemens Energy & Automation SIMOREG DC Master Base Drive Panel Operating Instructions NOTES:.
Siemens Energy & Automation 4-1 SIMOREG DC Master Base Drive Panel Operating Instructions 4 Receiving, unp acking SIMOREG Base Drive Panels are packed at the manuf acturing plant in protective containers suitable for shipping. Avoid dropping and shocks during unloadi ng and moving the SIMOREG during receiving.
4-2 Siemens Energy & Automation SIMOREG DC Master Base Drive Panel Operating Instructions NOTES:.
Siemens Energy & Automation 5-1 SIMOREG DC Master Base Drive Panel Operatin g Instructions 5 T echnical dat a: 5.1 15ADC to 100ADC Base Drive Panels, 3AC 460V, 1 & 4Q Rated supply voltage armature 1) V 3 Phase 460 (+10% / – 5%) Rated input current armature + field 2) A 17.
5-2 Siemens Energy & Automation SIMOREG DC Master Base Drive Panel Operatin g Instructions 5.2 140ADC to 850ADC Base Drive Panels, 3AC 460V, 1 & 4Q Rated supply voltage armature 1) V 3 Phase 460 (+10% / – 5%) Rated input current armature + field 2) A 129.
Siemens Energy & Automation 5-3 SIMOREG DC Master Base Drive Panel Operatin g Instructions 5.3 1180ADC, 1660ADC & 1680ADC Base Drive Panels, 3AC 460V, 1 & 4Q Rated supply voltage armature .
5-4 Siemens Energy & Automation SIMOREG DC Master Base Drive Panel Operatin g Instructions Notes: 1) Operation with reduced inp ut voltage will resu lt in reduced maximum output voltage accordin gly. 2) Values apply for rated DC output cu rren t on both the armature and field circuits.
Siemens Energy & Automation 5-5 SIMOREG DC Master Base Drive Panel Operatin g Instructions 6) Requirements to achieve control stability: The control stability (closed-loop PI control) is referred to the rated motor speed and ap plies when the SIMOREG converter is wa rm.
5-6 Siemens Energy & Automation SIMOREG DC Master Base Drive Panel Operatin g Instructions NOTES:.
Siemens Energy & Automation 6-1 SIMOREG DC Master Base Drive Panel Operatin g Instructions 6 Inst allation and Dimensions 6.1 Installation Information SIMOREG Base Drive Panels are desi gned as chassis units intended to be mounted in side a protective enclosure or inside a control room.
6-2 Siemens Energy & Automation SIMOREG DC Master Base Drive Panel Operatin g Instructions 6.2 Base Drive Panel Outlines: Dimensions are mm (inches) P X300 SI EMEN S 6RA7 0 238 ( 9.
Siemens Energy & Automation 6-3 SIMOREG DC Master Base Drive Panel Operatin g Instructions Dimensions are mm (inches) 6RA7 0 SIEME NS P X300 339 ( 13. 4) TERMINA LS 80 - 92 POWER TERMINALS L1, L 2, L3, A1, A2, GND 709 (27.9) 734 (2 8 . 9 ) 9 (0 . 4 ) 238 (9.
6-4 Siemens Energy & Automation SIMOREG DC Master Base Drive Panel Operatin g Instructions Dimensions are mm (inches) SIEM ENS P X300 6RA70 339 ( 13. 4) 238 (9. 4) 268 ( 10. 6) 15 (0 .6 ) 80 6 (31.7) 831 (32.7) POWER TERMINALS L1, L2 , L3, A1, A2, GND TER MIN ALS 8 0 - 92 100 AMP BASE DRIV E PA NEL, ( 1 & 4Q) MOUNTING HOLES FOR M8, (.
Siemens Energy & Automation 6-5 SIMOREG DC Master Base Drive Panel Operatin g Instructions Dimensions are mm (inches) SIE ME NS P X3 00 6RA70 L1 L2 L3 A 1 A2 326(12 .8) TERMIN ALS 80 - 92 266(10. 5) 290(11. 4) 12 (0.4 5) 10 (0 .4) 980 (3 8.6) 960 (3 7.
6-6 Siemens Energy & Automation SIMOREG DC Master Base Drive Panel Operatin g Instructions Dimensions are mm (inches) SIEM ENS P X30 0 6RA70 326(12.8) 10 (0. 4) 12 (0.45) 1100 (43 .3) 1120 (44 .1) 266 (10.5) 290 (11.4) 210 AMP BASE DRIVE PA NEL, (1 & 4Q) L1 L2 L3 A1 A 2 TERMINAL S 80 - 92 GROUND TERMINAL MOUNT IN G HOL ES FOR M 8 , (.
Siemens Energy & Automation 6-7 SIMOREG DC Master Base Drive Panel Operatin g Instructions Dimensions are mm (inches) 6R A70 SIEMENS TERMINA LS 80 - 9 2 L1 L2 L3 A1 A2 266 (10 .5) 10 (0.4) 290 ( 11 .4) 12 (0.45) 1160 (45.7) 1180 (46.5) 331 ( 13. 0) 255 AMP BASE DRIVE PANEL, (1 & 4Q) GROUND TERMI NA L MOUNTING HOLES FOR M8, (.
6-8 Siemens Energy & Automation SIMOREG DC Master Base Drive Panel Operatin g Instructions Dimensions are mm (inches) P X300 SI EMENS 6R A7 0 L1 L2 L3 A1 A2 430 AMP BASE DRIVE PANEL, (1 & 4Q) ADDITIONAL CLEARANCE REQ'D FROM CONTACTOR ARC CHUTE TO ANY GROUNDED METAL 35 (1.
Siemens Energy & Automation 6-9 SIMOREG DC Master Base Drive Panel Operatin g Instructions Dimensions are mm (inches) L1 L2 L3 A1 A2 P X300 SIEMENS 6R A70 376 ( 14. 8) 520 ( 20. 5) 550 ( 21. 6) 15 (0.6) 20 (0.8) 1200 (47.2) 880 (34.6 ) 280 (11.0 ) TE RMIN A LS 80 - 94 35 (1.
6-10 Siemens Energy & Automation SIMOREG DC Master Base Drive Panel Operatin g Instructions Dimensions are mm (inches) X300 P A1 A2 L1 L2 L3 SI EMEN S 6R A70 TERMINA LS 80 - 9 4 CABLE CONNECT IONS TO PO WER MODULE THIS A REA 850 AMP BASE DRIVE PANEL, (1 & 4Q) 42 5 (16 .
Siemens Energy & Automation 6-11 SIMOREG DC Master Base Drive Panel Operatin g Instructions Dimensions are mm (inches) X300 PM P M 1D1 1C1 H4 H2 H3 H1 X1 X2 1FS FU 2FS FU 4CF U 5CFU 6C FU 7CF U RA.
6-12 Siemens Energy & Automation SIMOREG DC Master Base Drive Panel Operatin g Instructions Dimensions are mm (inches) X300 PM P M2 1D1 1C1 MRE C 1FSF U 2FSF U 4CFU 5CFU 6CFU 7CFU RATED 600V,30 A .
Siemens Energy & Automation 6-13 SIMOREG DC Master Base Drive Panel Operatin g Instructions Dimensions are mm (inches) NOTE: SEMIC ONDUCT OR FUS ES ARE LOCATED IN S IDE THE POWER MODULE, (PM).
6-14 Siemens Energy & Automation SIMOREG DC Master Base Drive Panel Operatin g Instructions NOTES:.
Siemens Energy & Automation 7-1 SIMOREG DC Master Base Drive Panel Operating Instructions 7 Base Drive Panel Connections WARNING Base Drive Panels are operated at high voltages.
7-2 Siemens Energy & Automation SIMOREG DC Master Base Drive Panel Operating Instructions 7.1 Base Drive Panel Schematics H1 H2 H3 H4 230 V M BASE DRIVE PANEL, 15 AMPS, 1 & 4 QUAD TRANSFO RMER.
Siemens Energy & Automation 7-3 SIMOREG DC Master Base Drive Panel Operating Instructions H1 H2 H3 H4 230 V M BASE DRIVE PANEL, 30 AMPS, 1 & 4 QUAD TRANSFO RMER 1PFU 2PFU 3PFU 1CFU 3CFU 2CFU J.
7-4 Siemens Energy & Automation SIMOREG DC Master Base Drive Panel Operating Instructions H1 H2 H3 H4 230 V M BASE DRIVE PANEL, 60 AMPS, 1 & 4 QUAD TR ANSF ORM ER 1PFU 2PFU 3PFU 1CFU 3CFU 2CFU.
Siemens Energy & Automation 7-5 SIMOREG DC Master Base Drive Panel Operating Instructions H1 H2 H3 H4 230 V M BASE DRIVE PAN EL, 100 AM PS, 1 & 4 QU AD TR ANSF ORM ER 1PFU 2PFU 3PFU 1CFU 3CFU .
7-6 Siemens Energy & Automation SIMOREG DC Master Base Drive Panel Operating Instructions H1 H2 H3 H4 230 V M BASE DRIVE PAN EL, 140 AM PS, 1 & 4 QU AD TR ANSF ORM ER 1PFU 2PFU 3PFU 1CFU 3CFU .
Siemens Energy & Automation 7-7 SIMOREG DC Master Base Drive Panel Operating Instructions H1 H2 H3 H4 230 V M BASE DRIVE PAN EL, 210 AM PS, 1 & 4 QU AD TR ANSF ORM ER 1PFU 2PFU 3PFU 1CFU 3CFU .
7-8 Siemens Energy & Automation SIMOREG DC Master Base Drive Panel Operating Instructions H1 H2 H3 H4 230 V M BASE DRIVE PANEL, 255 AMPS, 1 & 4 QUAD TRAN SFO RMER 1PFU 2PFU 3PFU 1CFU 3CFU 2CFU.
Siemens Energy & Automation 7-9 SIMOREG DC Master Base Drive Panel Operating Instructions H1 H2 H3 H4 230 V BASE DRIVE PANEL, 430 AMPS, 1 & 4 QUAD TRAN SFORMER 1CFU 3CFU 2CFU J2 J1 85 82 84 83.
7-10 Siemens Energy & Automation SIMOREG DC Master Base Drive Panel Operating Instructions H1 H2 H3 H4 230 V BASE DRIVE PANEL, 510 AMPS, 1 & 4 QUAD TRAN SFORMER 1CFU 3CFU 2CFU J2 J1 85 82 84 8.
Siemens Energy & Automation 7-11 SIMOREG DC Master Base Drive Panel Operating Instructions H1 H2 H3 H4 230 V BASE DRIVE PANEL, 850 AMPS, 1 & 4 QUAD TRAN SFORMER 1CFU 3CFU 2CFU J2 J1 85 82 84 8.
7-12 Siemens Energy & Automation SIMOREG DC Master Base Drive Panel Operating Instructions 80 81 #4 AWG, 60 C TORQUE TO 11 INCH- LBS A1 A2 MOT OR = 50 0 VOLTS D C F.
Siemens Energy & Automation 7-13 SIMOREG DC Master Base Drive Panel Operating Instructions 80 81 #4 AWG, 60 C TORQUE TO 11 INCH- LBS A1 A2 MOT OR = 50 0 VOLTS D C F.
7-14 Siemens Energy & Automation SIMOREG DC Master Base Drive Panel Operating Instructions 80 81 #1 AWG, 60 C TORQUE TO 22 INCH- LBS A1 A2 MOT OR = 50 0 VO LTS D C F.
Siemens Energy & Automation 7-15 SIMOREG DC Master Base Drive Panel Operating Instructions NOTES:.
7-16 Siemens Energy & Automation SIMOREG DC Master Base Drive Panel Operating Instructions 7.2 Control Connections CUD1 TYPICAL C ONTROL CONNEC TIONS V V V I act M ANALOG 1 ANALOG 2 M M 13 14 15 1.
Siemens Energy & Automation 7-17 SIMOREG DC Master Base Drive Panel Operating Instructions Terminal Locations CUD1 34 35 36 37 38 39 46 47 48 54 56 57 58 59 60 26 27 28 29 30 31 32 33 1 2 3 4 5 6 .
7-18 Siemens Energy & Automation SIMOREG DC Master Base Drive Panel Operating Instructions 7.3 Control Connections CUD2 OPTIONAL CUD2 CONTROL CONNECTIONS V V ANALOG 3 ANALOG 4 M M 18 19 20 21 205 .
Siemens Energy & Automation 7-19 SIMOREG DC Master Base Drive Panel Operating Instructions Terminal Locations CUD2 210 211 212 213 214 215 216 217 X161 61 62 63 64 65 X162 44 45 40 41 42 43 50 51 .
7-20 Siemens Energy & Automation SIMOREG DC Master Base Drive Panel Operating Instructions 7.4 Description of Power/Control Terminals WARNING The Base Drive Panel might sustain serious or irreparable damage if connected incorrectly.
Siemens Energy & Automation 7-21 SIMOREG DC Master Base Drive Panel Operating Instructions Base Drive Panel Power Connections 430 to 1680 Amp RATING CABLE RANGE RECOMMENDED TORQUE 430AMP L1, L2, L.
7-22 Siemens Energy & Automation SIMOREG DC Master Base Drive Panel Operating Instructions Motor Armature circuit Function Terminal Connection values/Remarks P o ss i b l e settings Armature supply AC input Ground PE conductor Armature circuit motor connection L1 L2 L3 A1 A2 See technical data, section 5 for actual maximum current values.
Siemens Energy & Automation 7-23 SIMOREG DC Master Base Drive Panel Operating Instructions Electronics power supply, main c ontactor, and fans 1180 to 1680 amps Function Terminal Connection values.
7-24 Siemens Energy & Automation SIMOREG DC Master Base Drive Panel Operating Instructions NOTES:.
Siemens Energy & Automation 8-1 SIMOREG DC Master Base Drive Panel Operating Instructions 8 S t art-Up 8.1 General safety information for start-up NOTE Before handling any boards (in particular, t.
8-2 Siemens Energy & Automation SIMOREG DC Master Base Drive Panel Operating Instructions 8.2 Operator control panels The basic converter is equipped with a simple operator panel (PMU) as standard. A user-friendly panel with plain text display (OP1S) can be connected as an option.
Siemens Energy & Automation 8-3 SIMOREG DC Master Base Drive Panel Operating Instructions LED displays Run green LED LED illuminated ⇒ in “Torque direction active” state (MI, MII, M0). (See parameter r000) Ready yellow LED LED illuminated ⇒ in “Ready” state (o1 .
8-4 Siemens Energy & Automation SIMOREG DC Master Base Drive Panel Operating Instructions 8.3 Parameterization procedure Parameterization is the process of changing or setting parameter values, activati ng converter functions, or displaying measured values with the operator panel.
Siemens Energy & Automation 8-5 SIMOREG DC Master Base Drive Panel Operating Instructions 5. Manual shifting If the 5 existing digits on the 7-segment display are not sufficient to display a parameter value, the display first shows just 5 digits (see Fig.
8-6 Siemens Energy & Automation SIMOREG DC Master Base Drive Panel Operating Instructions 8.4 Ty pical Connection Diagrams L1 L2 L3 E-S TOP STA RT SPEE D SET PO INT (10K) X1 74 2 4 5 1 P1 0 REF+ R.
Siemens Energy & Automation 8-7 SIMOREG DC Master Base Drive Panel Operating Instructions L1 L2 L3 E-S TOP STA RT STO P SPEE D SET PO INT (10K) X1 74 2 4 5 1 P1 0 REF+ REF- COM 34 X1 71 37 38 39 3.
8-8 Siemens Energy & Automation SIMOREG DC Master Base Drive Panel Operating Instructions 8.5 Reset to factory default values and adjust offsets In order to start from a predefined set of parameter values, it is highly recommended that the “Restore to default” function be executed before a co mplete new start-up operation is begun.
Siemens Energy & Automation 8-9 SIMOREG DC Master Base Drive Panel Operating Instructions 8.6 Start-up procedure WARNING The Base Drive Panel is at a hazardous volt age level even when the line contactor is open. The gating board (board mounted directly to lowe r part of housing) has many circuits at hazardous voltage levels.
8-10 Siemens Energy & Automation SIMOREG DC Master Base Drive Panel Operating Instructions 1 Access authorization P051 . . . Key parameter 0 Parameter cannot be changed 40 Parameter can be changed P052 .
Siemens Energy & Automation 8-11 SIMOREG DC Master Base Drive Panel Operating Instructions 5.2 Operation w ith pulse encoder P083 = 2: The actual speed is s upplied by the pulse encoder (K0040) P1.
8-12 Siemens Energy & Automation SIMOREG DC Master Base Drive Panel Operating Instructions 6 Field data 6.1 Field control P082 = 0: Internal field is not us ed and field functions are not used.
Siemens Energy & Automation 8-13 SIMOREG DC Master Base Drive Panel Operating Instructions 8 Execution of optimization runs 8.1 The unit must be in operating stat e o7.
8-14 Siemens Energy & Automation SIMOREG DC Master Base Drive Panel Operating Instructions P051 = 26 Speed controller optimization run (process lasts approximately 6s).
Siemens Energy & Automation 8-15 SIMOREG DC Master Base Drive Panel Operating Instructions P051 = 28 Optimization run for compensation of friction moment and moment of inertia (if desired) (process lasts approx.
8-16 Siemens Energy & Automation SIMOREG DC Master Base Drive Panel Operating Instructions NOTE Optimization runs should be executed in the order listed above (precontrol and current controller, speed controller, and field weakening control, friction moment and moment of inertial compensation).
Siemens Energy & Automation 8-17 SIMOREG DC Master Base Drive Panel Operating Instructions 9.2 Speed Setpoint Selection With factory defaults, the Base Drive Panel is automatica lly configured to get the speed reference from the main setpoint analog input at terminals 4 and 5 on connector X174.
8-18 Siemens Energy & Automation SIMOREG DC Master Base Drive Panel Operating Instructions 9.3 Jog (Inching) Configuration If the unit is not already running, a JOG command can be giv en to the unit to cause it to start and run at a pre- selected speed.
Siemens Energy & Automation 8-19 SIMOREG DC Master Base Drive Panel Operating Instructions 10 Documentation of setting values • Save the parameter values using either Quick Start or the DriveMonitor PC program or • Document parameters manually If P052=0, only parameters that have been changed from the factory default are displayed.
8-20 Siemens Energy & Automation SIMOREG DC Master Base Drive Panel Operating Instructions NOTES:.
Siemens Energy & Automation 9-1 SIMOREG DC Master Base Drive Panel Operating Instructions 9 Fault s and alarms When a fault or alarm message is activated, it is displayed both on the simple operator control panel (PMU) and on the OP1S user-friendly operator control panel (see also Se ction 7.
9-2 Siemens Energy & Automation SIMOREG DC Master Base Drive Panel Operating Instructions relevant terminal in the case of F018) P952 number of faults A text is also displayed for each individual fault in parameter r951 (fault text lis t). These texts can, for example, be displayed on the OP1S.
Siemens Energy & Automation 9-3 SIMOREG DC Master Base Drive Panel Operating Instructions Fault Description No. Cause as a function of fault value (r047.
9-4 Siemens Energy & Automation SIMOREG DC Master Base Drive Panel Operating Instructions Fault Description No. Cause as a function of fault value (r047.
Siemens Energy & Automation 9-5 SIMOREG DC Master Base Drive Panel Operating Instructions Fault Description No. Cause as a function of fault value (r047.001, r949.001 or r949.009 with acknowledged error) Further information (r047.002 to r047.016) NOTICE This monitoring function is deactiva ted in the delivery state.
9-6 Siemens Energy & Automation SIMOREG DC Master Base Drive Panel Operating Instructions Fault Description No. Cause as a function of fault value (r047.
Siemens Energy & Automation 9-7 SIMOREG DC Master Base Drive Panel Operating Instructions Fault Description No. Cause as a function of fault value (r047.
9-8 Siemens Energy & Automation SIMOREG DC Master Base Drive Panel Operating Instructions Fault Description No. Cause as a function of fault value (r047.001, r949.001 or r949.009 with acknowledged error) Further information (r047.002 to r047.016) F021 External fault 1 (active in all operating states) Bit 15 in control word 1 was in the log.
Siemens Energy & Automation 9-9 SIMOREG DC Master Base Drive Panel Operating Instructions Fault Description No. Cause as a function of fault value (r047.
9-10 Siemens Energy & Automation SIMOREG DC Master Base Drive Panel Operating Instructions Fault Description No. Cause as a function of fault value (r047.
Siemens Energy & Automation 9-11 SIMOREG DC Master Base Drive Panel Operating Instructions Fault Description No. Cause as a function of fault value (r047.
9-12 Siemens Energy & Automation SIMOREG DC Master Base Drive Panel Operating Instructions Fault Description No. Cause as a function of fault value (r047.
Siemens Energy & Automation 9-13 SIMOREG DC Master Base Drive Panel Operating Instructions Fault Description No. Cause as a function of fault value (r047.
9-14 Siemens Energy & Automation SIMOREG DC Master Base Drive Panel Operating Instructions Fault Description No. Cause as a function of fault value (r047.
Siemens Energy & Automation 9-15 SIMOREG DC Master Base Drive Panel Operating Instructions Fault Description No. Cause as a function of fault value (r047.
9-16 Siemens Energy & Automation SIMOREG DC Master Base Drive Panel Operating Instructions Fault Description No. Cause as a function of fault value (r047.
Siemens Energy & Automation 9-17 SIMOREG DC Master Base Drive Panel Operating Instructions Fault Description No. Cause as a function of fault value (r047.
9-18 Siemens Energy & Automation SIMOREG DC Master Base Drive Panel Operating Instructions Fault Description No. Cause as a function of fault value (r047.
Siemens Energy & Automation 9-19 SIMOREG DC Master Base Drive Panel Operating Instructions Fault Description No. Cause as a function of fault value (r047.001, r949.001 or r949.009 with acknowledged error) Further information (r047.002 to r047.016) 31 The calculated armature circui t resistance is greater than 32.
9-20 Siemens Energy & Automation SIMOREG DC Master Base Drive Panel Operating Instructions Fault Description No. Cause as a function of fault value (r047.001, r949.001 or r949.009 with acknowledged error) Further information (r047.002 to r047.016) 1 the binector wired via parameter U103 Index.
Siemens Energy & Automation 9-21 SIMOREG DC Master Base Drive Panel Operating Instructions Fault Description No. Cause as a function of fault value (r047.
9-22 Siemens Energy & Automation SIMOREG DC Master Base Drive Panel Operating Instructions Fault Description No. Cause as a function of fault value (r047.001, r949.001 or r949.009 with acknowledged error) Further information (r047.002 to r047.016) 9.
Siemens Energy & Automation 9-23 SIMOREG DC Master Base Drive Panel Operating Instructions Fault Description No. Cause as a function of fault value (r047.
9-24 Siemens Energy & Automation SIMOREG DC Master Base Drive Panel Operating Instructions Fault Description No. Cause as a function of fault value (r047.
Siemens Energy & Automation 9-25 SIMOREG DC Master Base Drive Panel Operating Instructions Fault Description No. Cause as a function of fault value (r047.
9-26 Siemens Energy & Automation SIMOREG DC Master Base Drive Panel Operating Instructions Fault Description No. Cause as a function of fault value (r047.
Siemens Energy & Automation 9-27 SIMOREG DC Master Base Drive Panel Operating Instructions Fault Description No. Cause as a function of fault value (r047.
9-28 Siemens Energy & Automation SIMOREG DC Master Base Drive Panel Operating Instructions 9.2 Alarm messages Alarm message display: On the PMU: A (Alarm) and a three-digit number. The red LED (Fault) flashes. On the OP1S: On the bottom line of the operat ional display.
Siemens Energy & Automation 9-29 SIMOREG DC Master Base Drive Panel Operating Instructions Ala r m No. Description A025 Brush length too short (active in all operating states) When parameter P495=1 (binary sensing of brush length): Alarm in response to log.
9-30 Siemens Energy & Automation SIMOREG DC Master Base Drive Panel Operating Instructions Ala r m No. Description A033 Alarm message from free function block FB8 (active in all operating states) The binector connected via parameter U106 Index.001 is in the log.
Siemens Energy & Automation 9-31 SIMOREG DC Master Base Drive Panel Operating Instructions Ala r m No. Description A049 SCB1: No SCI slave connected (active in all operating states) A050 SCB1: Not.
9-32 Siemens Energy & Automation SIMOREG DC Master Base Drive Panel Operating Instructions NOTES:.
SIEMENS Energ y & Automat ion 10-1 SIMOREG DC Master Base Drive Pa nel Operating In structions 10 Parameter list Overview The Base Drive Panel Operating Instructions does not contain in formation about all available parameters. Only the pa rameters mentioned in th is book are included.
10-2 SIEMENS Energ y & Automat ion SIMOREG DC Ma ster Base D rive Panel Operating I nstruc tions Range of paramete r numbers Funct ion P831 - P899 Parameters f or Driv eMonitor a nd OP1S P918 - P9.
SIEMENS Energ y & Automat ion 10-3 SIMOREG DC Master Base Drive Pa nel Operating In structions Overview of abbreviations Example: PNU Descriptio n Value ra nge [Unit] Steps No.
10-4 SIEMENS Energ y & Automat ion SIMOREG DC Ma ster Base D rive Panel Operating I nstruc tions NOTES:.
SIEMENS Energ y & Automat ion 10-5 SIMOREG DC Master Base Drive Pa nel Operating In structions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / Status) 10.
10-6 SIEMENS Energ y & Automat ion SIMOREG DC Ma ster Base D rive Panel Operating I nstruc tions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / Status) o7.3 Waiting for completion of "Restore factory settings" operation.
SIEMENS Energ y & Automat ion 10-7 SIMOREG DC Master Base Drive Pa nel Operating In structions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / Status) 10.2 General visualizati on parameters r001 (G113) Display of termin als 4 and 5 (mai n setpoint) -200.
10-8 SIEMENS Energ y & Automat ion SIMOREG DC Ma ster Base D rive Panel Operating I nstruc tions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / St.
SIEMENS Energ y & Automat ion 10-9 SIMOREG DC Master Base Drive Pa nel Operating In structions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / Status) r022 (G160) Display of torque set point before to r que limitation Steps: 1 = ∧ 0.
10-10 SIEMENS Energ y & Automat ion SIMOREG DC Ma ster Base D rive Panel Operating I nstruc tions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / S.
SIEMENS Energ y & Automat ion 10-11 SIMOREG DC Master Base Drive Pa nel Operating In structions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / Status) P046 * (G121) Binector dis play: i001: Selecti on of bine ctor dis played in r045.
10-12 SIEMENS Energ y & Automat ion SIMOREG DC Ma ster Base D rive Panel Operating I nstruc tions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / Status) P053 * Control word for th e permanent memo ry [SW 1.
SIEMENS Energ y & Automat ion 10-13 SIMOREG DC Master Base Drive Pa nel Operating In structions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / Status) r059 Display of operating stat e Meaning as for r 000 0.
10-14 SIEMENS Energ y & Automat ion SIMOREG DC Ma ster Base D rive Panel Operating I nstruc tions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / Status) r064 (G101) Board compatib ilit y Compatibility ide ntifier of boards in location s 1 to 3 of electronics b ox.
SIEMENS Energ y & Automat ion 10-15 SIMOREG DC Master Base Drive Pa nel Operating In structions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / Sta.
10-16 SIEMENS Energ y & Automat ion SIMOREG DC Ma ster Base D rive Panel Operating I nstruc tions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / S.
SIEMENS Energ y & Automat ion 10-17 SIMOREG DC Master Base Drive Pa nel Operating In structions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / Status) 10.
10-18 SIEMENS Energ y & Automat ion SIMOREG DC Ma ster Base D rive Panel Operating I nstruc tions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / Status) P082 * (G166) Operating mode for field No field 0 No field is used (e.
SIEMENS Energ y & Automat ion 10-19 SIMOREG DC Master Base Drive Pa nel Operating In structions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / Sta.
10-20 SIEMENS Energ y & Automat ion SIMOREG DC Ma ster Base D rive Panel Operating I nstruc tions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / S.
SIEMENS Energ y & Automat ion 10-21 SIMOREG DC Master Base Drive Pa nel Operating In structions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / Sta.
10-22 SIEMENS Energ y & Automat ion SIMOREG DC Ma ster Base D rive Panel Operating I nstruc tions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / Status) P097 * (G166) Response of fi e ld current t o fault messag es [SW 2 .
SIEMENS Energ y & Automat ion 10-23 SIMOREG DC Master Base Drive Pa nel Operating In structions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / Sta.
10-24 SIEMENS Energ y & Automat ion SIMOREG DC Ma ster Base D rive Panel Operating I nstruc tions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / S.
SIEMENS Energ y & Automat ion 10-25 SIMOREG DC Master Base Drive Pa nel Operating In structions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / Status) P131 FDS (G165) (G166) Field cur re nt for 55% motor flux (fie ld character i stic, point no.
10-26 SIEMENS Energ y & Automat ion SIMOREG DC Ma ster Base D rive Panel Operating I nstruc tions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / Status) Example of a field characterist ic The examp le characteristic exhib its a sharper curvat ure (i.
SIEMENS Energ y & Automat ion 10-27 SIMOREG DC Master Base Drive Pa nel Operating In structions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / Status) 10.
10-28 SIEMENS Energ y & Automat ion SIMOREG DC Ma ster Base D rive Panel Operating I nstruc tions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / S.
SIEMENS Energ y & Automat ion 10-29 SIMOREG DC Master Base Drive Pa nel Operating In structions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / Sta.
10-30 SIEMENS Energ y & Automat ion SIMOREG DC Ma ster Base D rive Panel Operating I nstruc tions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / S.
SIEMENS Energ y & Automat ion 10-31 SIMOREG DC Master Base Drive Pa nel Operating In structions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / Status) P154 * FDS (G162) Set armatu re current co ntroller I co mponent to zero 0 Set controller I component to zer o (i.
10-32 SIEMENS Energ y & Automat ion SIMOREG DC Ma ster Base D rive Panel Operating I nstruc tions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / Status) P163 * FDS (G162) EMF filtering m et ho d for armature precon tro l 0 No filtering 1 Filtering element, f ilter time constant = a pprox.
SIEMENS Energ y & Automat ion 10-33 SIMOREG DC Master Base Drive Pa nel Operating In structions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / Status) P176 * FDS (G162) Source for variabl e Integration time [SW 1.
10-34 SIEMENS Energ y & Automat ion SIMOREG DC Ma ster Base D rive Panel Operating I nstruc tions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / S.
SIEMENS Energ y & Automat ion 10-35 SIMOREG DC Master Base Drive Pa nel Operating In structions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / Status) r218 (G151) (G152) Indication of the act ive inte g rat ion time of the speed co nt ro lle r [SW 1.
10-36 SIEMENS Energ y & Automat ion SIMOREG DC Ma ster Base D rive Panel Operating I nstruc tions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / S.
SIEMENS Energ y & Automat ion 10-37 SIMOREG DC Master Base Drive Pa nel Operating In structions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / Sta.
10-38 SIEMENS Energ y & Automat ion SIMOREG DC Ma ster Base D rive Panel Operating I nstruc tions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / Status) 10.
SIEMENS Energ y & Automat ion 10-39 SIMOREG DC Master Base Drive Pa nel Operating In structions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / Status) P284 * FDS (G165) Set EMF contr oller P c omponent to zer o 0 Set controller P component to zero (i.
10-40 SIEMENS Energ y & Automat ion SIMOREG DC Ma ster Base D rive Panel Operating I nstruc tions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / S.
SIEMENS Energ y & Automat ion 10-41 SIMOREG DC Master Base Drive Pa nel Operating In structions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / Status) P312 FDS (G136) Ramp-dow n time 3 0.00 to 650.
10-42 SIEMENS Energ y & Automat ion SIMOREG DC Ma ster Base D rive Panel Operating I nstruc tions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / Status) P321 FDS (G135) Multiplier for additiona l setpoint -300.
SIEMENS Energ y & Automat ion 10-43 SIMOREG DC Master Base Drive Pa nel Operating In structions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / Sta.
10-44 SIEMENS Energ y & Automat ion SIMOREG DC Ma ster Base D rive Panel Operating I nstruc tions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / Status) P373 FDS (G187) Speed thresh ol d n comp. Speed threshold fo r n < n comp.
SIEMENS Energ y & Automat ion 10-45 SIMOREG DC Master Base Drive Pa nel Operating In structions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / Sta.
10-46 SIEMENS Energ y & Automat ion SIMOREG DC Ma ster Base D rive Panel Operating I nstruc tions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / Status) P411 FDS (G120) K411 fixed v alue is appl ied to c onnec tor K0411 -199.
SIEMENS Energ y & Automat ion 10-47 SIMOREG DC Master Base Drive Pa nel Operating In structions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / Sta.
10-48 SIEMENS Energ y & Automat ion SIMOREG DC Ma ster Base D rive Panel Operating I nstruc tions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / S.
SIEMENS Energ y & Automat ion 10-49 SIMOREG DC Master Base Drive Pa nel Operating In structions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / Status) P453 * BDS (G145) Source for "E nable zer o mar ker counter" command [SW 1.
10-50 SIEMENS Energ y & Automat ion SIMOREG DC Ma ster Base D rive Panel Operating I nstruc tions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / Status) P464 FDS (G126) Time differe nce for dy/dt Settin g of dt for the output of dy /dt at a connector, i.
SIEMENS Energ y & Automat ion 10-51 SIMOREG DC Master Base Drive Pa nel Operating In structions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / Status) 10.25 Oscilla tion Function: Parameters P 480 to P483 define the waveshape of a rectangular signa l (oscillation setpoint K0 203).
10-52 SIEMENS Energ y & Automat ion SIMOREG DC Ma ster Base D rive Panel Operating I nstruc tions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / Status) P492 FDS (G185) An alog monit oring of moto r temperat ure: Trip tem perature Operativ e only when P 490.
SIEMENS Energ y & Automat ion 10-53 SIMOREG DC Master Base Drive Pa nel Operating In structions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / Status) 10.
10-54 SIEMENS Energ y & Automat ion SIMOREG DC Ma ster Base D rive Panel Operating I nstruc tions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / Status) 10.
SIEMENS Energ y & Automat ion 10-55 SIMOREG DC Master Base Drive Pa nel Operating In structions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / Status) 10.
10-56 SIEMENS Energ y & Automat ion SIMOREG DC Ma ster Base D rive Panel Operating I nstruc tions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / Status) 10.
SIEMENS Energ y & Automat ion 10-57 SIMOREG DC Master Base Drive Pa nel Operating In structions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / Status) P555 * FDS (G151) Source for the Influencin g quantity of the droop adapta tion [SW 1.
10-58 SIEMENS Energ y & Automat ion SIMOREG DC Ma ster Base D rive Panel Operating I nstruc tions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / Status) 10.
SIEMENS Energ y & Automat ion 10-59 SIMOREG DC Master Base Drive Pa nel Operating In structions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / Status) P592 * (G187) Source for a ctual v alue of " n < n comp.
10-60 SIEMENS Energ y & Automat ion SIMOREG DC Ma ster Base D rive Panel Operating I nstruc tions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / S.
SIEMENS Energ y & Automat ion 10-61 SIMOREG DC Master Base Drive Pa nel Operating In structions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / Status) P604 * (G161) Source for variabl e current limi t in torque direc tion II i001.
10-62 SIEMENS Energ y & Automat ion SIMOREG DC Ma ster Base D rive Panel Operating I nstruc tions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / S.
SIEMENS Energ y & Automat ion 10-63 SIMOREG DC Master Base Drive Pa nel Operating In structions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / Status) P615 * (G165) Source for EMF controll e r setpoint Selection of conne ctors to be injected as the EMF contr oller setpoint .
10-64 SIEMENS Energ y & Automat ion SIMOREG DC Ma ster Base D rive Panel Operating I nstruc tions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / S.
SIEMENS Energ y & Automat ion 10-65 SIMOREG DC Master Base Drive Pa nel Operating In structions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / Sta.
10-66 SIEMENS Energ y & Automat ion SIMOREG DC Ma ster Base D rive Panel Operating I nstruc tions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / S.
SIEMENS Energ y & Automat ion 10-67 SIMOREG DC Master Base Drive Pa nel Operating In structions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / Status) 10.
10-68 SIEMENS Energ y & Automat ion SIMOREG DC Ma ster Base D rive Panel Operating I nstruc tions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / S.
SIEMENS Energ y & Automat ion 10-69 SIMOREG DC Master Base Drive Pa nel Operating In structions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / Sta.
10-70 SIEMENS Energ y & Automat ion SIMOREG DC Ma ster Base D rive Panel Operating I nstruc tions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / S.
SIEMENS Energ y & Automat ion 10-71 SIMOREG DC Master Base Drive Pa nel Operating In structions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / Sta.
10-72 SIEMENS Energ y & Automat ion SIMOREG DC Ma ster Base D rive Panel Operating I nstruc tions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / S.
SIEMENS Energ y & Automat ion 10-73 SIMOREG DC Master Base Drive Pa nel Operating In structions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / Sta.
10-74 SIEMENS Energ y & Automat ion SIMOREG DC Ma ster Base D rive Panel Operating I nstruc tions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / S.
SIEMENS Energ y & Automat ion 10-75 SIMOREG DC Master Base Drive Pa nel Operating In structions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / Sta.
10-76 SIEMENS Energ y & Automat ion SIMOREG DC Ma ster Base D rive Panel Operating I nstruc tions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / S.
SIEMENS Energ y & Automat ion 10-77 SIMOREG DC Master Base Drive Pa nel Operating In structions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / Status) 10.
10-78 SIEMENS Energ y & Automat ion SIMOREG DC Ma ster Base D rive Panel Operating I nstruc tions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / Status) 10.
SIEMENS Energ y & Automat ion 10-79 SIMOREG DC Master Base Drive Pa nel Operating In structions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / Status) P786 * (G170) USS bus addr ess for G-SST 1 This parameter is functional only w hen P780=2 (USS protocol).
10-80 SIEMENS Energ y & Automat ion SIMOREG DC Ma ster Base D rive Panel Operating I nstruc tions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / S.
SIEMENS Energ y & Automat ion 10-81 SIMOREG DC Master Base Drive Pa nel Operating In structions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / Sta.
10-82 SIEMENS Energ y & Automat ion SIMOREG DC Ma ster Base D rive Panel Operating I nstruc tions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / S.
SIEMENS Energ y & Automat ion 10-83 SIMOREG DC Master Base Drive Pa nel Operating In structions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / Sta.
10-84 SIEMENS Energ y & Automat ion SIMOREG DC Ma ster Base D rive Panel Operating I nstruc tions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / S.
SIEMENS Energ y & Automat ion 10-85 SIMOREG DC Master Base Drive Pa nel Operating In structions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / Status) r810 (G170) Receive data on G-SST1 Display of data received via USS interfa ce 1 i001: Display process data word 1 .
10-86 SIEMENS Energ y & Automat ion SIMOREG DC Ma ster Base D rive Panel Operating I nstruc tions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / S.
SIEMENS Energ y & Automat ion 10-87 SIMOREG DC Master Base Drive Pa nel Operating In structions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / Status) 10.
10-88 SIEMENS Energ y & Automat ion SIMOREG DC Ma ster Base D rive Panel Operating I nstruc tions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / Status) 10.
SIEMENS Energ y & Automat ion 10-89 SIMOREG DC Master Base Drive Pa nel Operating In structions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / Status) 10.46 Fault memory r947 (G189) Fault memory Display of fault messages generated in response to recent fa ults.
10-90 SIEMENS Energ y & Automat ion SIMOREG DC Ma ster Base D rive Panel Operating I nstruc tions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / Status) 10.47 Visuali zation parameters: Alarms r953 Alarm parameter 1 Display of active a larms in bit-coded form (A00 1 to A016).
SIEMENS Energ y & Automat ion 10-91 SIMOREG DC Master Base Drive Pa nel Operating In structions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / Sta.
10-92 SIEMENS Energ y & Automat ion SIMOREG DC Ma ster Base D rive Panel Operating I nstruc tions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / Status) P971 * EEPROM tran sfer Transfer of pa rameter values from RAM to EERPROM on switchover from 0 to 1.
SIEMENS Energ y & Automat ion 10-93 SIMOREG DC Master Base Drive Pa nel Operating In structions PNU Descripti on Value range [Unit] Steps No. indices Factory setting Type See Change (A ccess / Status) r997 List of modified para meter numbers, continuation See r990.
10-94 SIEMENS Energ y & Automat ion SIMOREG DC Ma ster Base D rive Panel Operating I nstruc tions NOTES:.
Siemens Energy & Automation 11-1 SIMOREG DC Master Base Drive Panel Operating Instructions 11 Simplified block diagrams Basic functions Page Sheet 1 Legend ...........................................................................................
11-2 Siemens Energy & Automation SIMOREG DC Master Base Drive Panel Operating Instructions Sheet 1 Legend 8 7 56 4 3 2 1 6RA7 0 DC M AST ER SI MPLI FIE D BL OCK DIAG RAM 1 & 1 ≥ Pxx x ( 0) F.
Siemens Energy & Automation 11-3 SIMOREG DC Master Base Drive Panel Operating Instructions Sheet 2 Speed Setpoint System r001 + - FIXE D COMMA ND INCH COMMAND CRAW L COMMA ND RAMP - + P710 SPEED SETPOI NT SYSTEM FIX ED SET POI N T INCH SE TP OIN T CRAW L SE TP OIN T K198 -1 -1 K00 15 P0433.
11-4 Siemens Energy & Automation SIMOREG DC Master Base Drive Panel Operating Instructions Sheet 3 Speed Controller and Current Limit X1 73 XT P171 (1 00%) P172 (- 100%) P170 (0) 1 O CURRE NT TOR QUE r022 P225.F (3.0) K P P226.F (0.65 ) T N P228 .
Siemens Energy & Automation 11-5 SIMOREG DC Master Base Drive Panel Operating Instructions Sheet 4 Armature Current Control r018 FORW AR D RE VE RSE P155.F (.1) P156.F ( .2) K P T N CURR ENT CONT ROL LE R P160.F (0) REVERSING DEAD BAND REVERSING LOGIC ARMATURE CURRENT A CTUAL VALUE r019 r020 M P158.
11-6 Siemens Energy & Automation SIMOREG DC Master Base Drive Panel Operating Instructions Sheet 5 EMF and Field Current Control r034 P255.F (5) P256.F (.2) K P T N CUR R ENT CON T ROL LER K250 K260 K251 P250.F (0 ) P251.F (180 ) ADVANCE LIMI T RETARD LIMI T 0 0 P112 .
Siemens Energy & Automation 11-7 SIMOREG DC Master Base Drive Panel Operating Instructions Sheet 6 USS Interface 1 ( X300 ) .04 .01 .03 .02 .06 .05 .07 .08 .10 .09 .14 .11 .13 .12 .16 .15 Rx+/Tx+ Rx-/Tx- RS485 M 1 1 RS232 1 ≥ 2 3 4 5 6 7 8 9 TxD RxD 1 M +5V Su bmin D M + 1 0 1 0 WE r81 0.
11-8 Siemens Energy & Automation SIMOREG DC Master Base Drive Panel Operating Instructions Sheet 7 USS Interface 2 ( X172 ) .0 4 .0 1 .0 3 .0 2 .0 6 .0 5 .0 7 .0 8 .1 0 .0 9 .1 4 .1 1 .1 3 .1 2 .1 6 .1 5 Tx+ Tx- Rx+/Tx+ Rx-/Tx- RS485 M 56 57 58 59 60 1 1 M + 1 0 1 0 X172 WE Bit 0 .
Siemens Energy & Automation 11-9 SIMOREG DC Master Base Drive Panel Operating Instructions Sheet 8 Peer to Peer Interface ( X172 ) .01 .02 .03 .04 .05 Tx+ Tx- Rx+/Tx+ Rx-/Tx- RS485 M 56 57 58 59 60 G-SST 2 M + 1 0 1 0 X172 1 0 1 0 <1> <2> P7 90 (0) P7 97 (0,00 0s) P7 93 (6) P7 91 (2) r799 r8 12.
11-10 Siemens Energy & Automation SIMOREG DC Master Base Drive Panel Operating Instructions Sheet 9 Data Exchange CB / TB to Base (PZD) .0 4 .0 1 .0 3 .0 2 .0 6 .0 5 .0 7 .0 8 .1 0 .0 9 .1 4 .1 1 .1 3 .1 2 .1 6 .1 5 n73 3.0 1 to .16 U734 (0) K K K K K 1s B3030 B3031 K K K K K n735 .
Siemens Energy & Automation 11-11 SIMOREG DC Master Base Drive Panel Operating Instructions Sheet 10 Control Word 1 & & 1 ≥ 32 1B i t 0 4 5 6 7 Bi t8 9 10 11 12 13 14 15 1 ≥ 1 Bit 0 Bit 1 Bit 2 Bit 3 Bit 4 Bit 5 Bit 6 Bit 7 Bit 8 Bit 9 Bit 10 Bit 11 Bit 12 Bit 13 Bit 14 Bit 15 P667.
11-12 Siemens Energy & Automation SIMOREG DC Master Base Drive Panel Operating Instructions Sheet 11 Control Word 2 8 7 56 4 3 2 1 6RA70 DC MASTER SIMPLIFIED BL OCK DIAGR AM (ALL AVAILABLE FUNCT I.
Siemens Energy & Automation 11-13 SIMOREG DC Master Base Drive Panel Operating Instructions Sheet 12 Status Word 1 8 7 56 4 3 2 1 6RA70 DC MASTER SIMPLIFIED BLO CK DIAGRAM (ALL AVAILABLE FUNCTIO N.
11-14 Siemens Energy & Automation SIMOREG DC Master Base Drive Panel Operating Instructions Sheet 13 Status Word 2 8 7 56 4 3 2 1 6RA70 D C M AST ER SIMPLIFIED BLOCK DIAGRA M (ALL AVAILABLE FUNCTI.
Siemens Energy & Automation 11-15 SIMOREG DC Master Base Drive Panel Operating Instructions Sheet 14 Signals 8 7 56 4 3 2 1 6RA70 D C M AST ER SIMPLIFIED BLOCK DIAGRA M (ALL AVAILABLE FUNCTIONS ARE NOT SHOW N ON SI MPLIFI ED BLOCK DIAGRAM) 14 0T 0 1 T 0 0 1 0 1 & T 0 0 1 0 1 P381.
11-16 Siemens Energy & Automation SIMOREG DC Master Base Drive Panel Operating Instructions Sheet 15 Miscellaneous xxxx xxxx xxxx xxxx xxxx xxxx xxxx ... 8 7 56 4 3 2 1 xxxx xxxx xxxx xxxx xxxx xxxx xxxx ... P05 5. ( 012) (011. . .244) r056 P05 7 (012) 011.
SIMOREG DC Mast er 6RA70 Series Base Dr iv e I ns tr uctions Micr oprocessor -based conv er t ers fr om 15A to 1680A f or v ar iable speed DC dr iv es Re v 5.0 Siemens Energy & Aut omation, Inc. 3333 Old Milton Par kw ay Alphare tta, GA 30005 1-800-964-4114 seainf o@sea.
Ein wichtiger Punkt beim Kauf des Geräts Siemens 6RA70 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Siemens 6RA70 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Siemens 6RA70 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Siemens 6RA70 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Siemens 6RA70 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Siemens 6RA70 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Siemens 6RA70 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Siemens 6RA70. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Siemens 6RA70 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
