Benutzeranleitung / Produktwartung R-480J des Produzenten Sharp
Zur Seite of 40
R-480J TABLE OF CONTENTS Page CAUTION, MICROWAVE RADIATION ................................................................................................... .......... 1 WARNING .......................................................................
R-480J.
R-480J 1 SER VICE MANU AL MICROWAVE OVEN R-480J GENERAL IMPORTANT INFORMATION This Manual has been prepared to provide Sharp Corp. Service engineers with Operation and Service Information. It is recommended that service engineers carefully study the entire text of this manual, so they will be qualified to render satisfactory customer service.
R-480J 2 PR ODUCT SPECIFICA TIONS ITEM DESCRIPTION Power Requirements 230 - 240 Volts 50 Hertz Single phase, 3 wire earthed Power Consumption 1.65 kW Power Output 1200 watts nominal of RF microwave en.
R-480J 3 APPEARANCE VIEW 1. Ventilation openings 2. Oven lamp 3. Door hinges 4. Door safety latches 5. See through door 6. Door seals and sealing surfaces 7. Coupling 8. Door open button 9. Touch control panel 10. Digital readout 11. Waveguide cover 12.
R-480J 4 OPERA TION SEQUENCE because the relay (RY1) stays closed. Shown in the display is the remaining time. 6. MONITOR SWITCH CIRCUIT The monitor switch is mechanically controlled by oven door, and monitors the operation of the 1st. latch switch and 2nd.
R-480J 5 2. Heat potatoes. Moisture and humidity is emitted rapidly. You can smell the aroma as it cooks. 3. Sensor detects moisture and humidity and calculates cooking time and variable power. Cooking Sequence. 1. Touch each SENSOR COOK or SENSOR INSTANT REHEAT function pad to operating the sensor cooking.
R-480J 6 Figure D-1. Door Open Mechanism 1ST. LATCH SWITCH AND 2ND. INTERLOCK RE- LAY CONTROL SWITCH 1. When the oven door is closed, the contacts (COM-NO) must be closed. 2. When the oven door is opened, the contacts (COM- NO) must be opened. MONITOR SWITCH 1.
R-480J 7 SER VICING Microwave ovens contain circuitry capable of pro- ducing very high voltage and current, contact with any part of the high voltage circuit will result in electrocution. High voltage capacitor, Power trans- former, Magnetron, High voltage rectifier assem- bly, High voltage fuse, High voltage harness.
R-480J 8 CK = Check / RE = Replace Home fuse blows when power supply cord is plugged into wall outlet. FUSE F10A blows when power supply cord is plugged into wall outlet. Display does not show anything when power supply cord is plugged into wall outlet.
R-480J 9 TEST PROCEDURES PROCEDURE LETTER COMPONENT TEST A MAGNETRON TEST NEVER TOUCH ANY PART IN THE CIRCUIT WITH YOUR HAND OR AN INSULATED TOOL WHILE THE OVEN IS IN OPERATION. CARRY OUT 3D CHECK. Isolate the magnetron from high voltage circuit by removing all leads connected to filament terminal.
R-480J 10 D HIGH VOLTAGE CAPACITOR TEST TEST PROCEDURES PROCEDURE LETTER COMPONENT TEST Room temperature .................. To = 21˚C Initial temperature ................. T1 = 11 ° C Temperature after (35 + 3) = 38 sec. ............................
R-480J 11 TEST PROCEDURES PROCEDURE LETTER COMPONENT TEST B. Continuity check must be carried out with measuring instrument which is set to the highest resistance range. C. A normal capacitor shows continuity for a short time (kick) and then a resistance of about 10M Ω after it has been charged.
R-480J 12 K TOUCH CONTROL PANEL ASSEMBLY TEST TEST PROCEDURES PROCEDURE LETTER COMPONENT TEST H MOTOR WINDING TEST CARRY OUT 3D CHECKS. Disconnect the leads from the motor. Using an ohmmeter, check the resistance between the two terminals as described in the table below.
R-480J 13 TEST PROCEDURES PROCEDURE LETTER COMPONENT TEST b) At a certain digit, brightness is low. c) Only one indicator does not light. d) The corresponding segments of all digits do not light up; or they continue to light up. e) Wrong figure appears.
R-480J 14 TEST PROCEDURES PROCEDURE LETTER COMPONENT TEST Checking the initial sensor cooking condition WARNING : The oven should be fully assembled before following procedure. (1) The oven should be plugged in at least two minutes before sensor cooking.
R-480J 15 TEST PROCEDURES PROCEDURE LETTER COMPONENT TEST TESTING METHOD FOR AH SENSOR AND/OR CONTROL UNIT To determine if the sensor is defective, the simplest method is to replace it with a new replacement sensor. (1) Disconnect the power supply cord, and then remove outer case.
R-480J 16 T OUCH CONTROL P ANEL ASSEMBL Y OUTLINE OF TOUCH CONTROL PANEL The touch control section consists of the following units. (1) Key Unit (2) Control Unit (The Control Unit consists of Power Unit and LSI Unit). The principal functions of these units and the signals communicated among them are explained below.
R-480J 17 LSI The I/O signal of the LSI is detailed in the following table. Pin No. Signal I/O Description 1 COM5 OUT Common data signal : COM11. Connected to LCD signal COM11. 2 COM4 OUT Common data signal : COM12. Connected to LCD signal COM12. 3 COM3 OUT Common data signal : COM13.
R-480J 18 37 P05 OUT Key strobe signal. Signal applied to touch-key section. A pulse signal is input to AIN7, P14, P15, P16 and P17 terminal while one of G3 line keys on key matrix is touched. 38 P04 OUT Key strobe signal. Signal applied to touch-key section.
R-480J 19 Pin No. Signal I/O Description 63-66 AIN3-AIN0 IN Terminal to change cooking input according to the Model. By using the A/D converter contained in the LSI, DC voltage in accordance with the Model in operation is applied to set up its cooking constant.
R-480J 20 SW1 SW2 SW3 SW4 SW5 P20 P21 P22 P23 P24 LSI (IC1) AIN4 AIN5 620k 300k 150k 75k 37.4k 26 23 22 50 49 24 25 15k 15k 4.7k 1234 8765 0.01uF 0.1uF 0.01uF VA : -15V VA : -15V R90 330 C90 C91 C93 C92 S F-2 1.8k IC2 F-1 F-3 C 3.57k 3.32k VC : -5V 0.
R-480J 21 1. Precautions for Handling Electronic Components This unit uses CMOS LSI in the integral part of the circuits. When handling these parts, the following precautions should be strictly followed. CMOS LSI have extremely high impedance at its input and output terminals.
R-480J 22 COMPONENT REPLA CEMENT AND ADJUSTMENT PROCEDURE WARNING: Avoid possible exposure to microwave energy. Please follow the instructions below before operating the oven. 1. Disconnect the oven from the power supply. 2. Make sure that a definite “click” can be heard when the microwave oven door is unlatched.
R-480J 23 Removal 1. CARRY OUT 3D CHECKS. 2. Disconnect wire leads from magnetron. 3. Remove the two (2) screws holding the magnetron air duct to magnetron. And slide magnetron air duct slightly so that two (2) screws at left hand side of magnetron appear.
R-480J 24 OVEN LAMP AND LAMP SOCKET REMOVAL 1. CARRY OUT 3D CHECKS. 2. Remove one (1) screw holding the chassis support to the magnetron and magnetron air duct. 3. Remove one (1) screw holding the chassis support to the oven cavity front plate. 4. Remove the chassis support from the oven cavity.
R-480J 25 2. Install the fan motor to the back plate of the oven cavity with the two (2) screws. 3. Re-install the fan duct to the oven cavity. 4. Connect the wire leads to the fan motor and magnetron, referring to the pictorial diagram. Rear View Side View POWER SUPPLY CORD REPLACEMENT Removal 1.
R-480J 26 toward the oven face. Then check lower portion of the latch hook, pushing and pulling lower portion of the door toward the oven face. Both results (play in the door) should be less than 0.5mm. 2. The 1st. latch switch and 2nd. interlock relay control switch interrupt the circuit before the door can be opened.
R-480J 27 door panel upward. 5. Hold the door panel to the door frame with three (3) screws. 6. Re-install the latch spring to the latch head. Re-install the latch spring to the door frame. Re-install latch head to door frame. 7. Re-install choke cover to door panel by pushing.
R-480J 28 MICRO W A VE MEASUREMENT After adjustment of door latch switches, monitor switch and door are completed individually or collectively, the following leakage test must be performed with a survey instrument and it must be confirmed that the result meets the requirements of the performance standard for micro- wave oven.
R-480J 29 SCHEMATIC NOTE: CONDITION OF OVEN 1. DOOR CLOSED. 2. CLOCK APPEARS ON DISPLAY. NOTE: " " indicates components with potentials above 250V. Figure O-1. Oven Schematic-OFF Condition SCHEMATIC NOTE: CONDITION OF OVEN 1. DOOR CLOSED. 2.
R-480J 30 Figure S-1. Pictorial Diagram 1 A B C D E F G H A B C D E F G H 23 4 5 6 12 34 56 COM. MONITOR SWITCH COM. N.O. N.C. 2ND. INTERLOCK RELAY CONTROL SWITCH 1ST. LATCH SWITCH TURNTABLE MOTOR BLK GRY RED GRN GRN WHT BLK WHT WHT RED WHT WHT THERMAL CUT-OUT (OVEN) NOISE FILTER COM.
R-480J 31 Figure S-2. Power unitl Circuit 1 A B C D E F G H A B C D E F G H 23 4 5 6 12 34 56 + – + – + – A 1 B 2 B 1 CN-A R4 27 D5 T1 ab c d VRS1 (J1) D7 D8 1SS270A 1SS270A 10G471K C1 0.1 µ /50v C3 0.1 µ /50v ZD1 HZ16-1 C5 10 µ /35v C2 1000 µ /35v C4 10 µ /35v R1 2.
R-480J 32 Figure S3. CPU. Unit Circuit 1 A B C D E F G H A B C D E F G H 23 4 5 6 12 34 56 SENSOR DEFROST TURNTABLE OFF COOK HELP C11 + - 0.1uF/50V (J17) (J16) (J15) (J14) (J13) (J12) (J11) (J10) C13 47uF/16V ZD10 UDZ4.3B R15 C14 0.01uF/50V R11 R19 4.
R-480J 33 1 A B C D E F G H A B C D E F G H 23 4 5 6 12 34 56 Figure S-4. Printed Wiring Board WH - 1 SH - B SH - A 1 C3 C4 C5 R3 C2 F C1 10 D4 D2 D1 D3 D9 (D10) RY3 (CN - D) D8 ZD1 VRB DU R2 R1 R6 R5.
R-480J 34 ∆ ∆ PA R TS LIST Note: The parts marked " ∆ " may cause undue microwave exposure. The parts marked "*" are used in voltage more than 250V. REF. NO. PART NO. DESCRIPTION Q'TY CODE * * * * ∆ * * * ELECTRICAL PARTS 1- 1 RTHM-A120WRE0 Thermal cut-out 145 deg.
R-480J 35 HOW TO ORDER REPLACEMENT PARTS To have your order filled prompty and correctly, please furnish the following information. 1. MODEL NUMBER 2. REF.
R-480J 36 1 A B C D E F G H A B C D E F G H 23 4 5 6 12 34 56 OVEN AND CABINET PARTS 7-8 7-8 7-8 7-8 2-1 6-7 1-5 4-5 4-20 7-1 4-11 7-1 7-4 7-1 4-6 7-6 1-15 7-2 4-9 1-13 7-5 4-1 4-7 1-9 4-4 1-3 1-4 1-3.
R-480J 37 1 A B C D E F G H A B C D E F G H 23 4 5 6 12 34 56 CONTROL PANEL PARTS DOOR PARTS Actual wire harness may be different from illustration. 6-2 4-18 5-4 5-8 5-8 5-5 5-6 5-1 5-7 5-3 5-2 5 3-1 .
R-480J '04SHARP CORP. (08S0.CD_E) COPYRIGHT © 2004 BY SHARP CORPORATION ALL RIGHTS RESERVED. No part of this publication may be reproduced, stored in retrieval systems, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher.
Ein wichtiger Punkt beim Kauf des Geräts Sharp R-480J (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Sharp R-480J noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Sharp R-480J - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Sharp R-480J reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Sharp R-480J erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Sharp R-480J besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Sharp R-480J verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Sharp R-480J. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Sharp R-480J gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
