Benutzeranleitung / Produktwartung PG-A10S des Produzenten Sharp
Zur Seite of 103
LCD PROJECT OR MODEL PG-A10X PG-A10S OPERA TION MANUAL Introduction Connections and Setup Basic Operation Easy to Use Functions Appendix SHARP CORPORA TION Printed in Japan TINS-A505WJN1 03P02-JWM A10X_A10S#E_Print#H1+4.
IMPORT ANT For your assistance in reporting the loss or theft of your Projector , please r ecord the Serial Number located on the bottom of the projector and r etain this information.
SPECIAL NOTE FOR USERS IN THE U.K. The mains lead of this product is fitted with a non-r ewireable (moulded) plug incorporating a 5A fuse. Should the fuse need to be replaced, a BSI or AST A approved BS 1362 fuse marked or and of the same rating as above, which is also indicated on the pin face of the plug, must be used.
The supplied CD-ROM contains operation instructions in English, German, French, Swedish, Spanish, Italian, Dutch, Portuguese, Chinese (T raditional Chinese and Simplified Chinese) and Korean. Carefully r ead through the operation instructions before operating the pr ojector .
Introduction 1 Before using the projector , please read this operation manual carefully . There ar e two important reasons for prompt warranty r egistration of your new SHARP Projector , using the REGISTRA TION CARD packed with the projector .
2 W ARNING: The cooling fan in this projector continues to run for about 90 seconds after the pr ojector is turned off. During normal operation, when tur ning the power off always use the POWER OFF button on the pr ojector or on the remote control. Ensure the cooling fan has stopped befor e disconnecting the power cor d.
Introduction 3 Outstanding Features 1. Light and Compact Design • A4 / letter size projector weighing only 2.9 kg / 6.4 lbs can be easily transported from room to room or location to location .
4 Contents Easy to Use Functions Picture Display Mode ........................................ 40 Switching the Picture Display Mode ........................ 40 Still and Zoom Image ........................................ 42 Freezing a Moving Image .
Introduction 5 Appendix Carrying the Projector ...................................... 51 How to Use the Carrying Case ................................ 51 Maintenance ...................................................... 52 Replacing the Air Filter ..
6 1. Read Instructions All the safety and operating instructions should be read before the pr oduct is operated. 2. Retain Instructions The safety and operating instructions should be retained for futur e refer ence. 3. Heed Warnings All warnings on the product and in the operating instructions should be adhered to.
Introduction 7 18. Damage Requiring Service Unplug this product from the wall outlet and r efer servicing to qualified service personnel under the following conditions: a. When the power -supply cord or plug is damaged. b. If liquid has been spilled, or objects have fallen into the product.
8 IMPORT ANT SAFEGUARDS Be sur e to read the following safeguar ds when setting up your projector . Caution concerning the lamp unit ■ Potential hazard of glass particles if lamp ruptures. In case of lamp rupture, contact your nearest Sharp Authorized Projector Dealer or Service Center for a replacement.
9 Introduction PDF operation manuals in several languages are included in the CD-ROM, so that you can work with the projector , even if you do not have this manual. T o utilize these manuals, you need to install Adobe Acrobat Reader on your PC (Windows or Macintosh).
10 26 26 55 55 27 29 38 27 13 52 21 21 Power ON/OFF buttons For turning the power on or off. Power indicator Illuminates red when the projector is in standby. When the power is turned on, this indicator will illuminate green. Lamp replacement indicator Illuminates green indicating normal function.
Introduction 11 15 52 AC socket 21 Rear adjustment foot (on the bottom of the projector) Intake vent 16 Kensington Security Standard connector INPUT 1 terminal Terminal for computer RGB and component signals. 20 RS-232C terminal For controlling the projector using a computer.
12 Part Names Numbers in refer to the main pages in this operation manual where the topic is explained. Remote Control (Front View) 26 P ower ON/OFF buttons For turning the power on or off . 32 MENU button For displa ying adjustment and setting screens.
13 Introduction Using the Remote Control Inserting the Batteries The batteries (two R-6 batteries (“AA” size, UM/ SUM-3, HP-7 or similar)) are supplied in the package. 1 Press the ▲ mark on the cover and slide it in the direction of the arrow . 2 Insert the batteries.
14 Accessories Remote control RRMCGA138WJSA T wo R-6 batteries ( “ AA ” size, UM/SUM-3, HP-7 or similar) Power cord * For U.S., Canada, etc. (6' (1.8 m)) QACCDA016WJPZ For Europe, except U.K. (6' (1.8 m)) QACCV A006WJPZ * Use the power cord that corresponds to the wall outlet in your country .
15 Connections and Setup Connecting the Projector to Other Devices Before Connecting Note • Before connecting, be sure to turn off both the projector and the devices to be connected. After making all connections, turn on the projector and then the other devices.
16 Connecting the Projector to a Computer Connecting the thumbscrew cables ■ Connect the thumbscrew cable making sure that it fits correctly into the terminal. Then, firmly secure the connectors by tightening the screws on both sides of the plug. ■ Do not remove ferrite cores attached to the RGB cable.
Connections and Setup 17 “ Plug and Play ” function (when connecting to a 15-pin terminal) ■ This projector is compatible with VESA-standard DDC 1/DDC 2B. The projector and a VESA DDC compatible computer will communicate their setting requirements, allowing for quick and easy setup.
18 Connecting to Video Equipment Connecting the Projector to Other Devices Connecting to Video Equipment Using an S-video, a Composite Video or an Audio Cable Using an S-video, video, or audio cable, a VCR, laser disc player or other audio-visual equipment can be connected to INPUT 2, INPUT 3 and AU- DIO input terminals.
Connections and Setup 19 Optional cable 3RCA to 15-pin D-sub cable T ype: AN-C3CP (9'10" (3.0 m)) T o analog component output terminal T o audio output terminal DVD player or DTV * decoder C.
20 Connecting to a Computer Using a DIN-D- sub RS-232C Adaptor and an RS-232C Serial Control Cable When the RS-232C terminal on the projector is connected to a computer with a DIN-D-sub RS- 232C adapt.
21 Connections and Setup Setup Using the Adjustment Feet The height of the projector can be adjusted us- ing the adjustment feet at the front and rear of the projector when the surface the projector is placed on is uneven or when the screen is slanted.
22 Adjusting the Lens The image is focused and adjusted to the de- sired size using the focus ring or zoom knob on the projector . 1 Adjust the focus by rotating the focus ring. 2 Adjust zooming by moving the zoom knob. Setup Zoom in Z o o m o u t Zoom knob Focus ring Focus ring Zoom knob A10X_A10S#E_Print#p21_25.
Connections and Setup 23 90 ° 90 ° Example of standard setup Setting up the Screen Position the projector perpendicular to the screen with all feet flat and level to achieve an optimal image. Note • The projector lens should be centered in the middle of the screen.
24 STRETCH Mode (16:9) Picture (Screen) size Projection distance (L) Distance from the lens center Diag. ( χ ) Width Height Maximum (L1) Minimum (L2) to the bottom of the image (H) 250" (635 cm) 218" (553 cm) 123" (311 cm) 35' 1" (10.
Connections and Setup 25 When using the default setting. ▼ On-screen Display The image is reversed. When using the default setting. ▼ On-screen Display The image is inverted. Projecting a Reversed/Inverted Image Projection from behind the Screen ■ Place a translucent screen between the projector and the audience.
26 Image Projection ▼ Keycode input box Basic Procedur e Connect the required external equipment to the pro- jector before carrying out the following procedures. Info • The language preset at the factory is English. If you want to change the on-scr een display to another language, r eset the language accor d- ing to the procedur e on page 28 .
27 Basic Operation 3 Press , or on the remote control to select the IN- PUT mode. • After pressing once on the projector , use to se lect the desired input mode. Note • When no signal is received, “ NO SIG- NAL ” will be displayed. When a signal that the projector is not preset to re- ceive is received, “ NOT REG.
28 Image Projection ' , " , , | buttons MENU button Power OFF button ENTER button “Language” menu icon 6 Press on the projector or on the remote control, t he n press that button again while the confirmation message is dis- played, t o tu r n o f f t h e p r oj e ct o r .
29 Basic Operation Keystone Correction (Correcting T rapezoidal Distortion) Correcting Trapezoidal Distortion This function allows for Keystone (On-screen T rapezoidal Distortion) Correction. Note • When the image is projected either from the top or from the bottom towards the screen at an angle, the image becomes distorted trapezoidally .
30 Menu Items This list shows the items that can be set in the projector . ■ INPUT 1 Mode Note • In the “ Picture ” menu of INPUT 1, “ Color ” , “ Ti n t ” and “ Sharp ” are only displayed when “ Signal T ype ” is set to “ Component ” .
31 Basic Operation ■ INPUT 2 / 3 Mode Main menu +30 − 30 +30 − 30 +30 − 30 +30 − 30 +30 − 30 +30 − 30 +30 − 30 Main menu Sub menu Contrast Bright Color Tint Sharp Red Blue Reset CLR Te.
32 The menu screens allow you to adjust the image and various projector settings. Y ou can operate the menus from the remote control using the following procedure. Using the Menu Screen Example: “Picture” menu screen for INPUT 1 (RGB) mode Menu Selections (Adjustments) 1 Press .
33 Basic Operation 3 Press ' ' ' ' ' or " " " " " to select the item you want to adjust. • The selected item is highlighted. Note • T o display a single adjustment item, press after selecting the item.
34 Menu Selections (Settings) 1 Press . • The “ Picture ” menu screen for the se- lected input mode is displayed. Note • The on-screen display shown on the right is displayed when INPUT 1 (RGB ) mode is selected. 2 Press or | | | | | to display the other menu screens.
35 Basic Operation 3 Press ' ' ' ' ' or " " " " " to select the item you want to set, and then press | | | | | to display the sub menu. • The selected item is highlighted. Note • Press or to return to the pre- vious screen.
36 Y ou can adjust the projector ’ s picture to your preferences using the “ Picture ” menu. For operation of the menu screen, see pages 32 to 35. CLR Temp (Adjusting the Color Temperature) Select “ CLR T emp ” on the “ Picture ” menu and the desired color temperature setting.
37 Basic Operation Gamma (Gamma Correction) Gamma is an image quality enhancement function that offers a richer image by brightening the darker portions of the image without altering the bright- ness of the brighter portions.
38 Using the “ Fine Sync ” menu, you can adjust the computer image, match the computer dis- play mode, and check the input signal. For operation of the menu screen, see pages 32 to 35 .
39 Basic Operation Signal Info (Checking the Input Signal) Select “ Signal Info ” on the “ Fine Sync ” menu to check the current input signal informa- tion. Note • The projector will display the number of scanned lines available from audio-visual equipment such as a DVD player or Digital Video.
40 Picture Display Mode Switching the Picture Dis- play Mode Press . • Pressing changes the display as shown on pages 40 and 41 . • T o return to the standard image, press while “RESIZE” is displayed on the screen. This function allows you to modify or customize the picture display mode to enhance the input image.
41 Easy to Use Functions VIDEO 4:3 aspect ratio Letter box Squeezed 16:9 image Squeezed 4:3 image 16:9 aspect ratio 16:9 aspect ratio (4:3 aspect ratio in 16:9 screen) Output screen image Input Signal Image type DVD / Video 480 I , 480P , 540P , NTSC, P AL, SECAM 720P , 1080 I (16:9) : Cutout area on which images cannot be projected.
42 × 1 × 4 × 9 × 16 × 36 × 64 × 2 × 3 Y ou can instantly freeze a moving image and enlarge a specific portion of an image with the remote control. Using these functions, you can explain the image to the audience more effec- tively . Still and Zoom Image Freezing a Moving Image 1 Press .
43 Easy to Use Functions Keylock Function Locking the Operation Buttons Hold down on the projector for about 3 seconds while the projector is being turned on. Note • The keylock function does not af fect the opera- tion with the remote control buttons.
44 Y ou can use the “ Options ” menu to enhance the usage for the projector . For operation of the menu screen, see pages 32 to 35. Example: “ Options ” menu screen for INPUT 2 (S-Video) mode Lamp Timer (Life) (Check- ing the Lamp Life Status) Y ou can confirm the cumulative lamp usage time and the remaining lamp life (percentage).
45 Easy to Use Functions Video System (Setting the Video System) The video input system mode is preset to “ Auto ” ; however , a clear picture from the connected audio- visual equipment may not be received, depending on the video signal difference.
46 Auto Power Off (Auto Power Off Function) When no input signal is detected for more than 15 minutes, the projector will automatically power off if set to “ ON ” . The Auto Power Off function will be disabled if it has been set to “ OFF ” . Select “ ” (ON) or “ ” (OFF) in “ Auto Power Off ” on the “ Options ” menu.
47 Easy to Use Functions Password (Setting a Pass- word) A password must be set to activate the “ Anti-Theft ” function (Page 48). There is no factory preset for the password or the “ Anti-Theft ” settings. In this way , anyone can freely set a new password and “ Anti-Theft ” settings.
48 Anti-Theft (Setting the Anti- Theft) The anti-theft function prevents unauthorized use of the projector . Y ou can choose to use this func- tion or not.
49 Easy to Use Functions If you want to change the keycode, follow the procedure below . Note • When “ Anti-Theft ” is selected, the password in- put box will appear .
50 Reversing/Inverting Projected Images Y ou can reverse or invert the projected image for various applications using the “ PRJ Mode ” menu. For operation of the menu screen, see pages 32 to 35.
51 Appendix Carrying the Projector How to Use the Carrying Case When carrying the projector , attach the lens cap to the lens, and place it in the supplied carrying case. 1 Open the cover of the carrying case. 2 Remove the inner padding from the carrying case, and fold it in the direction of the arrows.
52 Cleaning Paper Wax Thinner Cleaning the lens ■ Use a commercially available blower or lens cleaning paper (for glasses and camera lenses) for cleaning the lens. Do not use any liquid type cleaning agents, as they may wear off the coat- ing film on the surface of the lens.
53 Appendix 1 2 3 Replacing the Air Filter Ta b • This projector is equipped with air fil- ters to ensure the optimal operating condition of the projector . • The air filters should be cleaned every 100 hours of use. Clean the filters more often when the projector is used in a dusty or smoky location.
54 4 Clean the air filter . • Clean the dust off the air filter and cover with a vacuum cleaner extension hose. 5 Replace the air filter . • Place the air filter underneath the tabs on the filter/lamp unit cover . 6 Replace the filter/lamp unit cover .
55 Appendix Maintenance Indicators ■ The warning lights on the projector indicate problems inside the projector . ■ If a problem occurs, either the temperature warning indicator or the lamp replacement indicator will illuminate red, and the power will turn off.
56 Info • If the temperature warning indicator illuminates, and the power turns of f, follow the above possible solutions and then wait until the projector has cooled down completely before plugging in the power cord and turning the power back on. (At least 5 minutes.
57 Appendix Lamp ■ It is recommended that the lamp (sold separately) be replaced when the remaining lamp life be- comes 5% or less, or when you notice a significant deterioration in the picture and color quality . The lamp life (percentage) can be checked with the on-screen display .
58 1 2 3 User service screw Tab Lamp unit BQC-PGA10X//1 Removing and Installing the Lamp Unit Info • Be sure to remove the lamp unit using the handle. Be sure not to touch the glass sur- face of the lamp unit or the inside of the projector . • T o avoid injury to yourself and damage to the lamp, be sure to carefully follow the steps below .
59 Appendix 5 Remove the lamp unit. • Loosen the securing screws from the lamp unit. Hold the lamp unit by the handle and pull it in the direction of the arrow . At this time, keep the lamp unit horizontal and do not tilt it. 6 Insert the new lamp unit.
60 RS-232C T erminal: 9-pin Mini DIN female connector Pin No. Signal Name I/O Reference 1 Not connected 2 RD Receive Data Input Connected to internal circuit 3 SD Send Data Output Connected to interna.
61 Appendix Response code format Normal response Problem r esponse (communication er ror or incorrect command) Command format CONTROL CONTENTS Power Off (Standby) Power On INPUT1 INPUT2 INPUT3 Lamp Us.
62 Computer Compatibility Chart Note • This projector may not be able to display images from notebook computers in simultaneous (CR T/LCD) mode. Should this occur , turn of f the LCD display on the notebook computer and output the display data in “ CRT only ” mode.
63 Appendix T roubleshooting Check • Projector power cord is not plugged into the wall outlet. • Power to the external connected devices is of f. • The selected input mode is wrong. • The A V MUTE function is working. • Cables incorrectly connected to rear panel of the projector .
64 Check Problem Page Picture is green on INPUT 1 COMPONENT . Picture is pink (no green) on INPUT 1 RGB. Picture is dark. Picture is too bright and whitish. • Change the input signal type setting. • The lamp replacement indicator is illuminating in red.
65 Appendix For SHARP Assistance If you encounter any problems during setup or operation of this projector , first refer to the “T roubleshooting” section on pages 63 and 64. If this operation manual does not answer your question, please contact the SHARP Service departments listed below .
66 Specifications LCD Projector PG-A10X / PG-A10S NTSC3.58/NTSC4.43/P AL/P AL-M/P AL-N/P AL-60/SECAM/ DTV480 I /DTV480P/DTV540P/DTV580 I /DTV580P/DTV720P/DTV1035 I /DTV1080 I LCD panel × 3, RGB optical shutter method Panel size: 0.79" (20.0 mm) (12 [H] × 16 [W] mm) No.
67 Appendix Side View Side View Top View Rear View Front View Bottom View ø 66 10 13 / 64 (258.8) 3 9 / 64 (79.5) 11 45 / 64 (297) 1 35 / 64 (39.2) 3 13 / 64 (81) 3 33 / 64 (89) 7 7 / 64 (180.5) 9 1 / 32 (229) 49 / 64 (19.1) 7 11 / 16 (195) 5 55 / 64 (148.
68 Glossary Anti-Theft If the “ Keycode ” set in the projector is not correctly entered, the projector will not operate even if sig- nals are entered. Aspect Ratio Width and height ratio of an image. The normal aspect ratio of a computer and video image is 4:3.
69 Appendix AC socket ............................................................. 15 Adjusting the Lens ............................................... 22 Adjustment buttons .............................................. 32 Adjustment feet .........
70 MEMO A10X_A10S#E_Print#p63_70.p65 03.2.4, 2:07 PM 70.
71 Appendix Bitte lesen Sie diese Bedienungsanleitung vor der V erwendung des Projektors sorgfältig durch. Einführung DEUTSCH Es gibt zwei wichtige Gründe für die baldige Garantie-Registrierung dieses neuen Pr ojektors von SHARP mit Hilfe der dem Projektor beiliegenden REGISTRIERUNGS-KAR TE: 1.
72 WICHTIGE SICHERHEITSHINWEISE ACHTUNG : V or der ersten Inbetriebnahme dieses Ger ä tes sollten Sie diese Bedienungsanleitung durchlesen und f ü r die Bezugnahme gut aufbewahren. Elektrische Energie kann viele n ü tzliche Funktionen ausf ü hren.
73 Appendix Lesen Sie beim Setup Ihres Pr ojektors unbedingt die folgenden Sicherheitshinweise. V orsichtsma ß nahmen bei der Handhabung der Lampeneinheit ■ Wenn die Lampe zerspringt, kann es zu V erletzungen durch Glassplitter kommen.
74 Die CD-ROM beinhaltet Bedienungsanleitungen im PDF-Format in mehreren Sprachen, damit Sie auch dann mit dem Projektor arbeiten k ö nnen, wenn Sie dieses Handbuch nicht vorliegen haben. Zur V erwendung dieser Anleitungen muss der Adobe Acrobat Reader auf Ihrem PC (Windows oder Macintosh) installiert sein.
75 Appendix INFORMA TIONS Cet appareil a été testé et r econnu conforme aux limites prescrites pour le matériel numérique de Classe A, selon les spécifications de la 15ème partie des Règles de la Commission Fédérale des Communications (FCC).
76 1. Lire les instructions Avant d ’ utiliser l ’ appareil, veuillez lire les instructions de s é curit é et d ’ emploi. 2. Conservez les instructions Les instructions de s é curit é et d ’ emploi doivent ê tre soigneusement conserv é es pour r é f é rence ult é rieure.
77 Appendix Assurez-vous de lir e les mesur es de sécurité suivantes lors de la mise en route de votr e projecteur . Mise en garde concernant l ’ ensemble lampe ■ Prenez les précautions nécessaires en raison des risques potentiels présentés par les particules de verre en cas de rupture de la lampe.
78 Les manuels techniques au format PDF et en plusieurs langues sont inclus dans le CD-ROM afin que vous puissiez travailler avec le projecteur m ê me si vous ne poss é dez pas ce manuel. Pour utiliser ces manuels, le progamme Adobe Acrobat Reader doit ê tre install é sur votre PC (Windows ou Macintosh).
79 Appendix Läs noga denna bruksanvisning innan projektorn tas i bruk. Det finns två viktiga anledningar till att snabbt r egistrera garantin för din SHARP-projektor med hjälp av registr eringskor tet som medföljer pr ojektorn.
80 VIKTIGA S Ä KERHETSF Ö RESKRIFTER OBSERVERA : L ä s dessa f ö reskrifter innan du anv ä nder produkten f ö r f ö rsta g å ngen och spara dem f ö r framtida bruk. Man kan anv ä nda elektricitet till m å nga praktiska saker . Denna produkt har utvecklats och tillverkats f ö r att kunna s ä kerst ä lla din personliga s ä kerhet.
81 Appendix Obser vera följande säkerhetsför eskrifter vid pr ojektor ns uppställning. Observera ang å ende lampenheten ■ Det föreligger risk för skärsår om lampan råkar spricka. Kontakta närmaste auktoriserade Sharp-projektorhandlare eller en serviceverkstad för att köpa en byteslampa om detta inträffar .
82 P å CD-ROM-skivan finns bruksanvisningar i PDF-format p å flera olika spr å k s å att du kan anv ä nda projektorn ä ven om du inte har denna bruksanvisning. F ö r att kunna anv ä nda dessa anvisningar m å ste du installera Adobe Acrobat Reader i din persondator (Windows eller Macintosh).
83 Appendix Antes de emplear el proyector , lea con atención este manual de manejo. Hay dos razones importantes por las que debe registrar rápidamente la garantía de su nuevo pr oyector SHARP , empleando para ello la T ARJET A DE REGISTRO entregada con el pr oyector .
84 IMPORT ANTES MEDIDAS DE SEGURIDAD PRECAUCI Ó N : Lea completamente estas instrucciones antes de usar el producto y cons é rvelas para poder consultarlas en el futuro. La energ í a el é ctrica puede tener muchas aplicaciones ú tiles. Este pr oducto ha sido dise ñ ado y fabricado para garantizar la seguridad del usuario.
85 Appendix Al instalar el pr oyector , asegúrese de leer y observar las siguientes medidas de seguridad. Advertencia acerca de la l á mpara ■ Si la lámpara se rompe las partículas de cristal pueden ser un peligro. Si la lámpara se rompe, solicite el reemplazo de la misma en el centro de servicio o distribuidor Sharp autorizado más cercano.
86 El CD-ROM incluye los manuales de manejo en varios idiomas en formato PDF , para que pueda utilizar el proyector aunque no tenga el presente manual. Para poder usar estos manuales debe tener instalado Adobe Acrobat Reader en su PC (Windows o Macintosh).
87 Appendix Prima di utilizzare il proiettore, leggere con attenzione il presente manuale di istruzioni. Vi sono due ragioni di rilievo per r egistrare rapidamente la garanzia del nuovo pr oiettor e SHARP appena acquistato servendosi della CARTOLINA DI REGISTRAZIONE contenuta nella sua confezione.
88 NORME DI SICUREZZA IMPORT ANTI ATTENZIONE : Leggete queste istruzioni prima di usare il prodotto e poi conservate le istruzioni per ogni riferimento futuro. L ’energia elettrica può ef fettuare molte funzioni utili. Questo prodotto è stato prodotto per assicurare la vostra sicurezza personale.
89 Appendix Assicuratevi di leggere le seguenti norme di sicurezza prima di impostare il proiettore. Precauzioni riguardanti l ’ unit à lampada ■ Se si rompe la lampada si possono verificare dei danni causati dai frammenti di vetro.
90 Nel CD-ROM sono disponibili i manuali d ’ uso in formato PDF in pi ù lingue, in modo da poter utilizzare il proiettore anche senza questo manuale. Per usare questi manuali, bisogna installare Adobe Acrobat Reader nel PC (Windows o Macintosh). Se non è stato ancora installato Acrobat Reader , è possibile installarlo dal CD-ROM.
91 Appendix INFORMA TIE Deze apparatuur is getest en bleek te voldoen aan de eisen en limieten voor Klasse A digitale apparatuur , overeenkomstig Deel 15 van de FCC-bepalingen, die ontworpen zijn om r edelijke bescher ming te verlenen tegen dergelijke storingen bij gebruik in een commerciële omgeving.
92 BELANGRIJKE VEILIGHEIDSVOORSCHRIFTEN LET OP : Lees al deze instructies door alvorens dit apparaat in gebruik te nemen en bewaar ze voor later gebruik. Met elektrische energie kunt u heel wat nuttige functies uitvoeren. Dit apparaat is zodanig ontworpen en ver vaardigd dat uw persoonlijke veiligheid wordt gevrijwaar d.
93 Appendix Lees de volgende veiligheidsvoorschriften voor dat u uw projector opstelt. V oorzichtig met de lampeenheid ■ Als de lamp gesprongen is, kunnen glassplinters gevaar veroorzaken. Indien de lamp gesprongen is, neemt u contact op met de dichtstbijzijnde erkende Sharp projector dealer of servicecentrum om de lamp te laten vervangen.
94 De cd-rom bevat handleidingen in PDF-formaat in verscheidene talen zodat u de projector kunt bedienen, zelfs als u deze handleiding niet tot uw beschikking heeft. Om deze handleiding te kunnen gebruiken, moet eerst Adobe Acrobat Reader op uw PC (Windows of Macintosh) geïnstalleerd zijn.
95 Appendix Antes de utilizar este projetor , leia atentamente este Manual de Operação. Existem duas boas razões para que você faça, sem demora, o registr o de garantia do seu novo Projetor SHARP , usando o CARTÃO DE REGISTRO que acompanha o apar elho.
96 INFORMA ÇÕ ES DE SEGURAN Ç A A TEN ÇÃ O : Leia por favor todas estas instru çõ es antes de operar este produto e guarde-as para uso posterior . A energia el é trica pode realizar muitas fun çõ es ú teis. Este pr oduto foi concebido e fabricado para garantir a sua seguran ç a pessoal.
97 Appendix Leia cuidadosamente as seguintes informações de segurança quando instalar o seu pr ojetor . Cuidados relativos à l â mpada ■ Perigo de ferimentos com part í culas de vidro caso a l â mpada se quebre.
98 Como Aceder os Manuais de Opera çã o PDF O CD-ROM inclui os manuais de opera çã o (em formato PDF) em v á rios idiomas, para que voc ê possa trabalhar com o projetor , mesmo que voc ê n ã o possua este manual. Para utilizar estes manuais, voc ê precisar á instalar Adobe Acrobat Reader no seu PC (Windows ou Macintosh).
110 MEMO A10X_A10S#Memo_Print#p110.p65 03.2.4, 2:10 PM 110.
Ein wichtiger Punkt beim Kauf des Geräts Sharp PG-A10S (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Sharp PG-A10S noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Sharp PG-A10S - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Sharp PG-A10S reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Sharp PG-A10S erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Sharp PG-A10S besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Sharp PG-A10S verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Sharp PG-A10S. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Sharp PG-A10S gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
