Benutzeranleitung / Produktwartung 358.356100-3.7/18"PS des Produzenten Sears
Zur Seite of 36
operator's manual Assembly Maintenance Repair Parts MODEL NO, '_ 358.356090-3.7/20" 358.356100-3.7/18"PS i .................... ii Sears, Roebuck and Co.
FULL ONE YEAR WARRANTY ON GASOLINE CHAIN SAW (Excluding Bar, Chain, Spark Plug, Air Filter and Starter Rope) - For one year from date of purchase, when you maintainl lubricate,'and tune up this c.
t SAFETY RULESAND PRECAUTIONS : WARNING! :_: Because a chain saw is a high-speed wood-cutting tool, special safety precautions must be observed to reduce the risk of personal accidents.
E. HANDLE FUEL WITH CAUTION .... 1. Eliminate all sources of sparks or flame in the areas where fuel is mixed, poured, or stored. There should be no smoking, open ftames, or work that could cause sparks: 2. Mix, pour and store fuel in a well-ventilated area, on bare ground, and in an approved, marked container.
KNOW YOUR CHAIN SAW A. INTRODUCTION The information found in this manual will help you properly prepare your chain saw for use, understand how to operate your saw safely, and perform maintenance required to keep your unit ingo0d working condition.
PREPARING YOUR SAW FOR USE A. GEEING READY 1. READ YOUR 0PERATOWS MANUAL CAREFULLY'" ..... ._ ...... Your Operators; Manual has been developed to i _ help you,prepare your saw for use and to under- • Stand its safe operation. It is;important that you read your manual completely to become familiar with the unit beforeyou begin assembly.
D. ATTACHING THE BAR AND CHAIN _ICAUTION:!Wear protective gloves when han. dling or operating your saw. The chain is sharp and can cut you even when it isnot moving! • Your saw is equipped with a Lo-Kick ® Guide Bar and a Guard Link Chain designed to help reduce kickback.
E. CHAIN TENSION • COrrect chain tension is very important: --a loose chain will wear the bar and itself, --a loose chain can jump off the bar while you are cutting.
3. HOW TO MIX FUEL a. Pour one-half of the gasoline into an ap- proved, marked container. Do not try to mix oil and gasoline directly in the fue! tank. b. Add entire measure of 2*cycle Engine Oil. c. Mix. d. Add remainder of gasoline. e. Mix thoroughly for one minute.
USING YOUR SAW .... i i A. CONTROL DEVICES Understanding the control devices on your saw is an important part of learning how to properly and safely operate the unit. Figure 13. _ 1: The ignition Switch is a!oggte switch which is moved up for the "Start" position and mov- ed down for the' "Stop" i_osition.
C. CONTROLLING KICKBACK ........ Kickback isa dangerous reaction thatcancause serious personal injury. Carefully study this man- ual before you make the first cut with your new saw.
USING THE POWER SHARP®SYSTEM (MODEL 358.356100) , , , , ,, • Model 358.356100 is equipped with a Power Sharp ® : System that will perform approximately 80% of the sharpening necessary for the saw chain. The Power Sharp® System uses a built-in grinding stone to shar- pen the cutter top plates and set depth gauges.
B. HAND FILING Sharpen the side ptates by hand after every 3rd to 5th time the Power Sharp® System is used. items Required: Gloves flat file 5/32" file vise file holder NOTE: If abrasive materials such as rocks, nails, sand or dirt are contacted by the chain, the side plates should be checked more often.
TYPES OF CUTTING ..... Ae BASIC CUTTING TECHNIQUE 1. IMPORTANT POINTS. • a. Cut wood only. Do not cut metal, plastics, masonry, non-wood, building materials;etc. b. Stop the saw if the chain strikes a foreign object. Inspect the unit and repair or replace parts as necessary.
2. b. FELLING SMALL TREES -- LESS THAN 6" IN DIAMETER a. If you knowthe direction offall: 1.) Make a single felling cut on the side away from the direction of fall. 2.) Cut all the way through. 3.) Stop the saw, put it down, and get away quickly on your planned retreat path.
C. BUCKING Bucking is the term used for.cutting a fallen tree to the desired log size. 1. IMPORTANT POINTS a. Cut only one log at a time. b. Cut shattered wood very carefuilyl Sharp pieces of wood could be flung toward the operator. c. Use a sawhorse to cut small logs.
5. BUCKING w USING A STAND (Figure 35): a. b÷ In areaA: 1 .) Undercut 1/3 of the way through the log. 2.) Finish with an overcut. In area B: 1 .) Overcut 1/3 of theway through the log. 2,) Finish with an undercut. D. DEBRANCHING ANDPRUNING II ,:.i: • Work slowly, keeping both hands on the saw = with a firm grip.
H L¸: _ : . , MAINTENANCE 18 A good maintenance program of regular inspec- tion and care will increase the service life and help to maintain the safety and performance of your saw. • Make all adjustments or repairs (except car- buretor adjustments) with: spark plug wire disconnected engine cool as opposed to a unit that has just been run.
2. GUIDE BAR MAINTENANCE • Conditions which can require guide bar maintenance: --saw cuts to one side --saw has to be forced through a cut --inadequate supply of oil to bar and chain. • Check the condition of the guide bar each : r time the chain is sharpened.
,i .... e. f. g. Blow out loosened carbon with com- pressed air. • Clean the Spark arrestor screen with a wire brush or replace if breaks in the screen are found. Reassemble muffler parts. 2. SPARK PLUG • Maintenance is indicated when the engine is hard to start.
5. Remove the pulley screw in the center of the ..... pulley. Figure 50. _ _ _ :.. " 6. Lift the pulley carefully while gently twisting it counterclockwise _ , and remove the _ old rope. .: : 7. Move away from the fuel tank and burn the end of the new rope to go into the pulley.
3. Remove the fan housing. _ 4. Use a 9!16" socket wrench on the flywheel nut to keep the crankshaft from moving. Figure54. ' NOTE: Place the socket handle forward as shown in Figure 54. 5. Remove the clutch with a 314,. socket or end wrench in a clockwise direction:.
4, IDLE SPEED ADJUSTMENT--II a. Allow engine to idle. b. Adjust if the chain is turning by turning the IdleSpeed Screw counterclockwise _ . c. Squeeze the throttlei:trigger; The saw should accelerate without hesitating.
H. STORAGE When your ,saw is to be stored for over 30 days 3. always: 4. 5. 1, . Drain fuel tank in asafe manner (see Impor- tant Points, page9.) Start Engine and allow to run at an idle speed until the engine stops, NOTE: This will remove most of the fuel from the fuel system.
J. TROUBLE SHOOTING CHART TROUBLE CAUSE REMEDY ENGINE WILL NOT START EI_GINE'WlLL NOT IDLE- PROPERLY 1. ignition Switch off. 2. Fuel tank empty. 3. Spark Plug not firing. 4. Fuel n0t reaching carburetor. 5. Engine flooded. 6. Compression low. 1. Idling speed set too low.
MAINTENANCE CHART " ,i Visual inspection (condition, leaks) Complete machine ..... clean Throttle trigger, safety throttle Ioc4k, stop switch " ==__i 8" X x Check operation x Clean Felt x Filter in fuel tank ..... ......................
•NOTES 27.
SEARS CHAIN SAW PARTS LIST MODELS 358.356090 358.356100 3.7/20" 3.7/18" PS Figure I 49 23 36 43 44 _--2 _-31 ,25 26 29 10 59 12' 56 60 61 46 50 51 / 28.
SEARS CHAINSAWPARTS LIST MODELS 358:356090 358.356100 3.7/20" 3.7/18"PS 2 3 ,41 5 6 7 Part No. Qty. 39095 1 23817 2 STD522525 2 15434 2 24476 1 1626 1 1722 1 9 15123 10 STD600603 11 30054 12 42053 13 24329 14 42051 15 42066 ....... 16 15364:.
SEARS CHAIN:SAW PARTS LIST MODELS 358.356090 358.356100 3.7/20" 3.7/18"PS 4 1 ,28 Figure 2 38-- 39 45 MODEL 358.356100 3.7/18"PS (only) CARBURETOR ASSEMBLY PART NO. 35094 8--_. 15_h_, +, _ 1 "+J'_/_ _30 4 ..... +] ++_.o_+_ 27 5.
Key No. 1 2 3 4 5 6 7 8 9 11 12 13 t4 15 16 17 18 19 20 21 22 23 24 25 26 27 28 Key No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 Pad No. Qty. 25919 1 STD511003 1 10347 1 19107 1 24229 1 19101 1 15194 2 11965 1 24383 1 SEARS CHAIN SAW PARTSMST MODELS! 358.
SEARS CHAIN SAW PARTS LIST MODELS 358.356090 358.356100 ........ 3.7/20" 3.7/18"PS Figure 3 51 B 32 See 1 #36 14 ,5/._ 10 12 ,43 44 32 33 41' 49 57 CHAIN REPAIR KIT I 72 64 57 68 i 67 MODEL 358.
SEARS CHAINSAW PARTS LIST MODELS 358.356090 358.356100 3.7/20" 3.7/18"PS Figure 3 Key No. 1 Part No. STD5t1003 24351 24348 15357 32049 2 3 5 6 7 48069 48071 8 24465 Qty.
r NOTES 34 ¸¸.
QUICK REFERENCE PAGE Read and follow all Safety Rules, Precautions and Operating Instructions. Failure to do so can result in serious personal injury. page SAFETY RULES AND PRECAUTIONS ................................. • ........... 3-4 PREPARATION .
iiii i i [Sears] MODEL NO. 358.356090-3.7/20" 358.356100-3.7/18"PS How to Order Repair Parts SEARS SERVICE ) ,,, ,,,, ,,,, 66371-1-12084-2-17884 The Model Number will be found under the handle with the Serial Number. Always mention the Model Number when requesting ser- vice or repair parts for your Chain Saw.
Ein wichtiger Punkt beim Kauf des Geräts Sears 358.356100-3.7/18"PS (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Sears 358.356100-3.7/18"PS noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Sears 358.356100-3.7/18"PS - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Sears 358.356100-3.7/18"PS reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Sears 358.356100-3.7/18"PS erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Sears 358.356100-3.7/18"PS besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Sears 358.356100-3.7/18"PS verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Sears 358.356100-3.7/18"PS. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Sears 358.356100-3.7/18"PS gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
