Benutzeranleitung / Produktwartung 113=235240 des Produzenten Sears
Zur Seite of 32
Save This Manual _X_ For Future Reference SEARS owner's manuaa MODEL NO, 113.235220 & 113=235240 COMPOUND MITER SAW MODEL NO. 113.235110 NON-COMPOUND MITER SAW Serial Number Model and serial number may be found on a plate attached to your saw, at the side of the Miter Saw arm.
fir FULL ONE YEAR WARRANTY ON CRAFTSMAN MITER SAW within .... one year from the date of purchase, this Craftsman Miter Saw fails due to a defect in material or workmanship, Sears will repair it, free of charge. Warranty service is available by simply contacting the nearest Sears service center/department throughout the United States.
Before Each Use: Inspect your miter saw. • Disconnect The Miter Saw to avoid injury from accidental starting before changing the setup. changing the blade or adjusting anything • Compare the direc.
Safety Instructions For Miter Saws (Continued)- Inspect your workpiece, . Make sure there are no nails or foreign objects in the part of the workpiece to be cut Plan your work to avoid thrown pieces caused - when the workpiece binds on the blade and is torn from your hands.
Glossary of Terms for Woodworking ............... Arbor Miter Cut The shaft on which a cutting tool is mounted An angle cutting operation made across the width of the Bevel Cut workpiece An angle cutting operation made through the face of the Resin workpiece A sticky, sap based substance that has hardened.
Motor Specifications and Electrical Requirements (Continued) DANGER: To avoid electrocution: 1. Use only identical replacement parts when servicing a tool with double insulation. Servicing should be performed by a qualified service technician. 2. Do not use in rain or where floor is wet, This tool is intended for indoor residential use only.
Unpacking and Checking Contents ii u Tools Needed Tools required for alignment: 1 Combination Square 2 Combination wrench, !/4" Hex "L" wrench with #2 phillips tip (supplied) QUARE 1/2 .
Getting to Know "Your Miter Saw 1 Warning label 2,, Stop Shaft - The miter saw can be locked in the lowered position for compact storage. 3 Miter Lock Knob - The miter lock knob securely locks the miter saw at a desired miter angle Index points have been provided at O, 22.
Assembly ...................................................................... Removing or Installing the Blade WARNING: To avoid injury from a thrown work- piece or thrown pieces of blade, do not use a blade larger or smaller than 10" diameter.
Assembly (continued) Assembling Dust Elbow 1 Locate the dust elbow 2 Unplug power cord. 3 With the miter arm locked in the down position, start the dust elbow onto the dust nozzle at an angle to retaining lip.
Alignment (continued),, Adjustment of Miter Scale Indicator 1 Loosen the phiitips screw that holds the indicator in place 2 Reposition the indicator and retighten screw WARNING: To avoid injury from unexpected starting or electrical shock, do not plug the saw in, The power cord must remain unplugged whenever you are working on the saw.
Mounting The Miter Saw .................................... WARNING: To avoid injury from unexpected saw movement: a. Before moving the saw, lock the miter (and bevel if applicable) lock knob, and lock the power head in the lower position using the stop shaft.
Catalog No. 9-22246 Leg Set Legset Mounting Holes for Miter Saws 1' I' I O° °O "% 0 o o MOUNTING HOLES o o 0 O e °O I /" o o o o Stiffener-Side Stiffener*End Attach miter saw to holes indicated Recommended mounting hardware (not included) Qty 5/16-18xl -1/2" or longer hex head bolts 4 5/16-flat washers .
Safety Instructions For Basic Saw Operations Before Using The Miter Saw: WARNING: To avoid mistakes that could cause serious, permanent injury, do not plug the miter saw in until the following steps are com- pleted,, • Completely Assemble and Align Saw (See "Assembly" and "AJignment" sections).
Plan ahead to protect your eyes, hands, face, ears. Know your miter saw° Read and understand the owner's manual and labels affixed to the tool Learn its application and limitations as well as th.
• When cutting irregularly shaped workpieces, plan your work so it will not slip and pinch the blade and be torn from your hands. A piece of molding, for example, must lie fiat or be held by a fixtu.
Basic Saw Operations (Continued) Miter Cut When a miter cut is required, loosen the miter lock knob, depress the index spring, and move the saw to the desired angle, Retighten miter lock knob Do not stand in front of the saw table Move with the handle to the miter angle to make the cut E / / _.
Basic Saw Operations Compound Cut Model 113.235220 & 113,235240 Compound Miter Saw Only: When a compound cut is required, select the correct bevel and miter pesitionr Move your feet and body with the handle to the desired miter angle to make the cut.
Basic Saw Operations (Continued) Workpiece Support Long pieces need extra supports. The supports should be placed along the workpiece so the workpiece does not sag and your hand holding the workpiece is posi- tioned 4" or more from the blade path.
Basic Saw Operations ..................................... Cutting a Dimensional 4x4 (3-1/2" x 3-1/2" actual) with one cut. A dimensional 4x4 may be cut with one cut by attaching an auxiliar.
Basic Saw Operations (Continued) Tips for Cutting Compound Miters Model 113.235220 & 113,235240 Only: A compound miter is a cut requiring both a miter setting and bevel setting A compound miter is.
Maintenance and Lubrication Maintenance DANGER: Never put lubricants on the blade while it's spinning. WARNING: To avoid injury from unexpected starting or electrical shock, unplug the power cord before working on the saw.
Sears Recommends the Following Accessories Recommended Accessories I WARNING: To avoid injury from unsafe acces- sories, use only accessories shown on the rec- ommended accessories list in this manual.
Trouble Shooting Guide ° Motor ........................ PROBLEM PROBABLECAUSE SUGGESTED CORRECTIVEACTION Brake does not stop 1 blade within 6 seconds. 2.. Motor does not start. Brush sparking when switch released. Brushes not seated or lightly sticking.
WHITE FIELD WINDING BLACK WlDE BLADE WIRE NUT ii [ lllllll[BW ' _ BLACK POWER CORD BRUSH #1 BRUSH #2 "==e3 SPDT SWITCH BLACK Circuit Diagram Trouble Shooting of brake by qualified ser- vice person only.
Repair Parts ................... PARTS LIST FOR CRAFTSMAN 10" MITER SAWS MODEL NO. 113.235220 & 113,235240 AND 113.235110 FIGURE 1 18 19 17 20 21 13 26 A MODEL113235220 & 1t 3 235240 ONLY.
Repair Parts PARTS LIST FOR CRAFTSMAN 10" MITER SAWS MODEL NO. 113.235220 & 113.235240 AND 113,235110 FIGURE 1 Always order by Part Number m Not by Key Number Key Part Description No.
Repair Parts ............................... r_n I o L_ i FOR _.R_F'r, S_,_N 10" ,_.T_.r, SAWS NOD EL NO. 'I 13.235220 & 113.235240 AND 113.
Repair Parts .................... PARTS LIST FOR CRAFTSMAN 10" MITER SAWS MODEL NO, 113.235220 & 113.235240 AND 113.2351!0 FIGURE 3--PIVOT ASSEMBLY 234 5 6 Always order by Part Number-- Not by Key Number Key--- Part Description NO.
PARTS LIST FOR CRAFTSMAN 10" MITER SAWS MODEL NO. 113.235220 & 113.235240 AND 113.235110 FIGURE 4 I 03 O 16 14 13 12 19 18 17 8 7 9 11.
CO ..& PARTS LIST FOR CRAFTSM_N 10" MITER SAWS MODEL NO. 113.235220 & 113.235240 AND 113.235110 FIGURE 4 Key No. 1 2 3 4 5 6 7 8 9 10 10 11 12 13 14 15 16 I7 18 19 Part No.
f owner's manual SERVICE MODEL NO. 113.235220 & ] 13.235240 COMPOUND MITER SAW 113=235110 NON-COMPOUND MITER SAW IF YOU NEED REPAIR SERVICE OR PARTS: For repair service, call this toll free n.
Ein wichtiger Punkt beim Kauf des Geräts Sears 113=235240 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Sears 113=235240 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Sears 113=235240 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Sears 113=235240 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Sears 113=235240 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Sears 113=235240 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Sears 113=235240 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Sears 113=235240. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Sears 113=235240 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
