Benutzeranleitung / Produktwartung 113.22643 des Produzenten Sears
Zur Seite of 24
Save This Manual For Future Reference BELT AND DiSC SANDER Serial Number Model and serial number may be found on the back side of the base You should record both model and serial number in a safe place for future use.
FULLONE YEAR WARRANTY ON CRAFTSMAN BELT AND DISC SANDER If with In one year from the data of purchase, th Is Craftsman Be It and Disc Sander fails due to a defect in mater lal or workmanship, Sears will repair it, free of charge.
BEFORE EACH USE: Inspect your sander. DISCONNECT THE SANDER. To avoid injury from accidental starting, unplug the sander, turn the switch off and remove the switch key before changing the setup, sanding disc or belt or adjusting anything. CHECK DAMAGED PARTS.
safety instructions for belt and disc sander • Wear nonslip footwear. Plan the way you will hold the workpiece from start to finish. • Noise levels vary widely. To avoid possible headng damage, wear ear plugs or muffs when using sander for hours at a time.
motor specifications and electrical requirements This machine is designed to use, and is equipped with, a3450 RPM motor. It is wired foroperation on 120 volts, 60 Hz., alternating current. WARNING: To avoid electrocution or fire, tool must not be converted to operate on 240 volts.
contents POWER TOOL WARRANTY ......................... 2 SAFETY INSTRUCTIONS FOR BELT D)SC SANDEF ............................................. 2 MOTOR SPECIFICATIONS AND ELECTRICAL REQUIREMENTS ........................... 5 UNPACKING AND CHECKING CONTENTS .
assembJy MOUNTING BELT AND DISC SANDER TO WORKBENCH If belt and disc sander is to be used in a permanent location, it should be fastened securely to a firm support- ing surface such as a workbench, If mounting to a workbench, holes should be drilled through supporting surface of the workbench using dimensions illustrated.
assembly INSTALLING SANDING DiSC AND GUARD 1. Locate sanding disc and pee backing from disc. Align perimeter of disc with I_late and press disc firmly into position all the way around. 2. Locate disc guard and two pan head screws, M4,2 x 1.4-12 from loose Darts bag.
4. Locatewasher 6.5 x 17.8 x 1.6 and knob among loose pads, 5. Position table support in corresponding holes on side of base as shown. Make sure the 9.
assembly AUXILIARY MOUNTING FOR VERTICAL SANDING 1. Remove backstoplock bolt and removework support. 2. Removetable assembly by removing table lock knob and washer. NOTE: Beitbed may be raised to vertical position by loosening he× socket screw and raising bed.
3. Slide tension lever to the left to apply belt tension. 4. Tighten hex socket screw when bed is in desired position. 5. Plug in the power cord. Turn switch "ON" and imme- diately "OFF," noting if the belt tends to slide off the idler pulley or drive pulley.
4 TENSION LEVER 6 AUXILIARY MOUNTING HOLE WORK SUPPORT / HEX SCREW BED 3 TRACKING KNOB 2 BED LOCKING HEX SOCKET HEAD SCREW 5 TABLE LOCK KNOB HOLE 1 WORK SUPPORT SANDING BELT SANDING PLATE SANDING DISC.
ON-OFF SWITCH The On-Off switch has a locking feature. THIS FEA- TURE IS INTENDED TO HELP PREVENT UNAUTHOR- IZED AND POSSIBLY HAZARDOUS USE BY CHIL- DREN AND OTHERS. 1. To turn machine "ON" insert key into switch. NOTE: Key is made of yellow plastic, located in loose parts bag, 2.
BEFORE USING THE SANDER WARNING: To avoid mistakes that could cause serious, permanent injury, do not plug the sander in untU the following steps are comp|eted. - Assembly and alignment. (See pages 7 - 11 } = Learn the use and function of the ON-OFF switch.
Dress for safety, Any power sander can throw foreign objects into the eyes. This can cause permanent eye damage. Wear safety goggles (not glasses) that comply with ANSI Z87.1 (shown on package). Everyday eyeglasses have only impact resistant lenses. They are not safety glasses.
i bas c operation BEVEL SANDING The worktable can be tilted from 0 o to 45 ° for bevel sanding. Loosen the table lock knob and tilt the work- table to desired angle as shown.
SURFACE SANDING ON THE SANDING BELT WARNING: To avoid injury from sflps, jams or thrown pieces, adjust the backstop to clear the sanding surface by no more than 1/16 of an inch. When checking clearance between the belt and work support, press the belt flat against the metal beneath it.
basic operation Always sand outside curves on the left side of center on the sanding disc as shown. WARNING: Applying the workplece to the right side of the disc could cause workplece to fly up (kick- back) and result In an Injury.
maintenance WARNING: For your own safety, turn switch "OFF" and remove plug from power source outlet before adjuSting, maintaining, or lubrlcsting your belt and disc sander. WARNING: TO avoid electrocution or fire, any re- pairs to electrical systems should be done only by qualified service technicians.
maintenance 4. Slightly tighten (3) screws. Adjust tension of belt by putting blade screwdriver in adjusting hole. Push up on screwdriver to tighten tension between pulleys. 5 Tighten screws being careful not to disturb belt. STANDARD SCREWDRIVER ADJUSTING HOLE 6.
troubleshooting WARNING: For your own safety, turn switch "OFF" and remove plug from power source outlet before troubleshooting your sander. TROUBLE PROBABLE CAUSE Motor will not run. 1. Defective On-Off switch Defective switch cord. Defective switch box.
repair parts o ! / 22.
repair parts PARTS LiST FOR CRAFTSMAN BELT AND DiSC SANDER MODEL 113.226430 Key No. 1 2 3 4 5 Part No. 820247 820175 821156 819496 820235 6 820249 7 STD852006 6 820238 9 819481 10 9-28394 11 820383-4 .
SERVICE MODEL NO. 113.226430 HOW TO ORDER REPAIR PARTS BELTAND DISC SANDER Now that you have purchased your Belt and Disc Sander, should a need ever exist for repair parts or service, simply contact any Sears Service Center and most Sears, Roebuck and Co.
Ein wichtiger Punkt beim Kauf des Geräts Sears 113.22643 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Sears 113.22643 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Sears 113.22643 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Sears 113.22643 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Sears 113.22643 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Sears 113.22643 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Sears 113.22643 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Sears 113.22643. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Sears 113.22643 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
