Benutzeranleitung / Produktwartung SCCP30 des Produzenten Scotsman Ice
Zur Seite of 29
Introduction: This ice machine is the result of Scotsman ’s decades of experience as an industry leader in the design and manufacture of both commercial and residential ice machines. This manual includes the information needed to install, start up and maintain the ice machine.
Specifications This ice machine is designed to be used indoors, in a controlled environment. It can be used in a wide variety of environmental conditions, but there are limits. Use outside of the listed limitations is misuse and will void the warranty.
Cabinet Layout September 2009 Page 3 SCCG30 & SCCP30 Service Manual 14 7/8" AIR IN AIR OUT .75 SHEET MET AL DOOR FRONT .63 MIN. CABINET DOOR 29 1/4" 1" LEG ADJUSTMENT (4) PLACES 33 3/8" MIN.
Air flow The machine takes in room temperature air at the lower right front and forces warm air out the lower left front. Restricting the airflow will adversely affect the ability of the ice machine to make ice. Scotsman Ice Systems are designed and manufactured with the highest regard for safety and performance.
Water Quality All water, including potable water supplied by municipalities, contains some impurities or minerals. Water absorbs impurities from the air as rain and/or as it flows through the ground. Some of the impurities are solid particles, these are known as suspended solids, and a fine particle filter will remove them.
Door Covering Door Panel The ice machine is supplied without a conventional door covering so it can be decorated to the user ’s preference. Scotsman offers several coverings including white, black and stainless steel. In addition, a custom built panel can be placed onto the door.
Door Panel Attachment September 2009 Page 7 SCCG30 & SCCP30 Service Manual Gasket Scotsman Door Panel Cover Machine Screw Use Upper Hole at the Top Use Lower Hole at the Bottom Hole Plug.
Custom Panel A custom panel of wood or other material not exceeding 15 lb can be attached to the door. Attachment is from the ice side of the door. Holes are provided in the door for this purpose. To create and attach a custom panel: • Panel width: 14 7/8” • Panel height: Between 29 3/8” and 30 3/8”.
Door swing change The door can be attached to open with hinges on the left or right using new brackets shipped loose in the ice bin. Retain all screws for re-use. To change: 1. Remove innermost screw holding each hinge to cabinet, loosen the other. 2.
Installation: Water & Drain The recommended water supply tubing is ¼ inch OD copper. Stainless steel flex or reinforced PVC tube may also be used. Install an easily accessible shut-off valve between the supply and the unit. This shut-off valve should not be installed behind the unit.
Gravity Drain Caution: Restrictions in the drain system to the machine will cause water to back up into the ice storage bin and melt the ice. Gravity drain tubing must be vented, have no kinks and slope to the building drain. Air gaps are typically required by local code.
Electrical & Start Up The ice machine is supplied with a power cord. Do not remove the grounding pin from the cord ’s plug. Do not use extension cords. Follow all codes. Connect the machine to its own 115 volt, 15 amp circuit. 1. If the electrical outlet for the ice maker is behind the unit, plug in the unit.
Cube Size Adjustment The size of the ice cubes is determined by how long the ice machine is in the freezing cycle. That is controlled by the cube size thermostat. The cube size thermostat 's sensing portion is attached to the suction tube, near the outlet of the evaporator.
Harvest Time Adjustment The harvest time can be adjusted so that all the ice is released during the harvest period, with a few seconds extra for a safety margin. The adjustment range is between 2 to 5 minutes. There is an adjustment screw on the surface of the electronic timer.
Use No special instructions are needed for use. Just take as much ice as you need, the machine will replace it. A scoop is provided, and it can be stored in the machine using the loop of tubing on the right side as a holder. The machine can be shut off anytime by moving the On/Off switch to OFF.
How to clean the condenser and winterize. Condenser cleaning The condenser is like the radiator on a car, it has fins and tubes that can become clogged with dirt and lint. To clean: 1. Remove the kickplate and front service panel. 2. Locate the condenser surface.
How to remove scale from the ice making system. 1. Scoop out all of the ice, either discard it or save it in an ice chest or cooler. 2. Switch the machine Off. 3. Pour 8 ounces of Scotsman Ice Machine Scale Remover (available from a local Scotsman Distributor or Dealer) into the ice machine reservoir.
System Information Overall: • Refrigerant: 8 oz R-134a • Compressor: Hermetic, 700 BTUH • Condenser: Forced draft • Fan blade: 3 blade, 6 inch • Evaporator: Inverted, 12 cube cells.
Water System The water system consists of a water pump, inlet water solenoid valve, reservoir with overflow standpipe and spray platform. Harvest cycle : The inlet water solenoid valve is open during the harvest cycle. Water flows through it to the top of the machine and onto the evaporator platen.
Model and Serial Plate Location Components September 2009 Page 20 SCCG30 & SCCP30 Service Manual Condenser and Bin Thermostat Inlet Water Solenoid Valve Model and Serial Tag Location Bin Thermosta.
Performance Information Listed cycle times are after the 3rd consecutive cycle, will vary a minute or so, and will be longer for built in units. Harvest time is usually 2 minutes, longer in very cold conditions. Ice per cycle: 1/2 lb Water drained / cycle: Varies by harvest cycle length and purge setting.
Refrigeration System September 2009 Page 22 SCCG30 & SCCP30 Service Manual S u ction P r essu r e 0 10 20 30 40 50 60 70 Ti m e PSI G Di sch ar ge Pressu r e 0 20 40 60 80 100 120 140 Ti me PSI G.
Service Diagnosis No Ice Problem Likely Cause Probable Solution No power to unit Power disconnected Check breaker or fuse. Reset or replace, restart and check Very long freeze cycle Dirty condenser Cl.
Service Diagnosis Makes excessive noise Problem Likely Cause Probable Solution Fan blade vibrates Blade is bent Replace fan blade Fan motor mount is broken Replace motor mount Compressor vibrates Moun.
Removal and Repair Bin Thermostat 1. Disconnect electrical power. 2. Remove service panel. 3. Remove back panel. Note: If unit is built in it must be pulled out to change the bin thermostat. 4. Pull cap tube out from the back of the ice storage bin and cap tube holder.
Removal and Repair Cube Size Thermostat 1. Disconnect unit from electrical power. 2. Remove door. 3. Remove top panel. 4. Remove service panel. 5. Remove back panel. 6. Cut cable tie holding cube size bulb in evaporator well. Pull bulb out of well. 7.
Removal and Repair - Cabinet Removal Certain components require the removal of the cabinet for repair access. 1. Shut machine off, if making ice, melt ice with hot water. 2. Remove all ice. 3. Drain reservoir. 4. Remove service panel and kick plate. 5.
15. Lift evaporator platen up and tilt back enough for bin assembly to clear the base. 16. Remove air baffle. 17. Unplug wire harness connector (at back of bin). 18. Remove 1 screw at each corner of the base. 19. Lift bin assembly off the base. Note: Prop evaporator assembly up.
Refrigeration Service This ice machine use R-134a type refrigerant. There are specific rules for handling that refrigerant. To check for system pressures, add a field supplied clamp-on type service valve as a temporary means of system access.
Ein wichtiger Punkt beim Kauf des Geräts Scotsman Ice SCCP30 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Scotsman Ice SCCP30 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Scotsman Ice SCCP30 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Scotsman Ice SCCP30 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Scotsman Ice SCCP30 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Scotsman Ice SCCP30 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Scotsman Ice SCCP30 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Scotsman Ice SCCP30. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Scotsman Ice SCCP30 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
