Benutzeranleitung / Produktwartung SLP38C des Produzenten Savin
Zur Seite of 66
Operating I n st ruc tions Maintenance Guide 1 Read thi s manual car efully b efore you use thi s prod uct and k eep it h andy fo r future reference. For safety, p le ase follow the instru c tions in this manu al.
Introduction This man ual conta ins d etailed i nstruc tions on t he ope ration a nd maint enanc e of this m achine. To get maximu m versa tility from this ma chine all op erators should care fully read an d follow th e instru ctions in this man ual. Pleas e keep th is ma nual in a handy pl ace n ear the ma chine .
i Trademarks Micros oft ® , Wi ndows ® and Windows NT ® are regi ster ed tr ademar ks of Mi- cros oft Co rpor at ion in the U nited Stat es a nd/or othe r coun tri es. IPS-PRINT ™ Printer La nguage Em ulation © Copyright 1999- 2000, XIONICS DOCUMEN T TECHNOLOGIES , INC.
ii Safety Information When using your printer, the following safety pr ecautions should al ways be fol- lowed. Safety D uring Operatio n In this manual, the following i mportant symbols are used: R WA.
iii R CAUTION: • Protect the equipment from damp ness or wet weather, such as rain, snow, and so on. • Unplug the power cord from the wall outle t before you move the equipmen t. While moving the equipment, you shou ld take care that the power cord will not be dam aged under the equip ment.
iv ENERGY STAR Program ❖ ❖ ❖ ❖ Low-power Mode (Energy Saver mode) This printer auto matically lowers its power co nsumption 60 minutes after the last operation has been completed. To exit Low-power (Energy Saver) mode, press any key on the operation panel.
v How to Read This Manual Symbols In this manual, the following sy mbols are used: R WARNING: This sym bol indicates a potentia lly hazard ous situ ation whi ch, if instructio ns are not followed, could result in death or serious inj ury.
vi TABLE OF CONTENTS 1. Replacing Consumables and Maintenance Kit Detaching the SR770 (2 Tray Finisher) .................. .............. .............. ...... 1 Opening and Closing the Duplex Reversal Unit ....... .............. .......... ...... 2 Replacing the Toner Car tridge .
1 1. Replacing Consumables and Maintenance Kit Detaching the S R770 (2 Tray Finisher ) There are times when you might have to detach th e 2 Tray Finisher from the printer to remove misfed paper. This section desc ribes how to detac h the 2 Tray Fini sher.
Replacing Consumables and Maintenance Kit 2 1 Opening and Closing the Duplex Reversal Unit There are times when you might have to detach the Duplex R eversal Unit to remove mi sfed paper. This sectio n describes how to detach the Duplex Reversal Unit.
Replacing the Toner Cartridge 3 1 Replacing the Toner Cartridge R WARNING: R CAUTION: Note ❒ The actual number of printed pag- es will dif fer depending on the p a- per t ype, size, conten ts and settings. For more information, see P.50 “ Toner cartridge ” .
Replacing Consumables and Maintenance Kit 4 1 B Remove the toner cartridge for the color you want to replace. A Unhook the green h ook on the toner cartridg e with one hand. B Holding the tone r cartridge with the othe r hand, pu ll out the cartridge up slow ly.
Replacing the Toner Cartridge 5 1 F Inse rt t he to ner car tri dge slowl y until the green ho ok snaps on the metal contact area. Important ❒ Do not install and remove the toner cartridg es over and o ver. This could re sult in a toner leak. G Close the upper righ t cover.
Replacing Consumables and Maintenance Kit 6 1 Replacing the Fuser Oil Unit R CAUTION: If " Repla ce Fu ser Oil Un it (T ypeG )" appears on the panel display, replac e the Fuser Oil Unit. Replace Fuser Oil Unit (Typ eG) A Turn off the power switch and unplug th e power ca ble.
Replacing the Fuser Oil Unit 7 1 G Holding the green hand le, pull up the Fu sing Unit sl owly in the direction of the arrow . Important ❒ Do not t ouch a ny areas other than t he h andle . H Put the removed Fusing Unit in a stable and le vel place.
Replacing Consumables and Maintenance Kit 8 1 K Hold the Fuser Oil Unit in the manner shown in the illustration. Matc h ( U U U U ) on the front of th e Fus- er Oil Unit and ( T T T T ) on the Fusing Unit at three places.
Replacing the Fuser Oil Unit 9 1 R Plug in the p ower cable and turn on the power sw itch. Note ❒ If you dispose of the used toner cartridges by yourself, dispose of them according to lo cal regu- lations.
Replacing Consumables and Maintenance Kit 10 1 Replacing the Photoconducto r Unit If "Replace Black PCU (Typ e F)" ap- pears on the panel display, replace the black Photo conductor Unit. Replace Black PCU (Type F) If "Replace Color PCU (Ty pe A)" ap- pears on the panel display, replace the three color Photoco nducto r Units.
Replacing the Photoconductor Unit 11 1 F Lift the inner cover until it clicks into place and holds. The Ph oto con ducto r Un it s are in- stalled as shown in the illustration. The black Photoconductor Un it is at the uppe r left period. The other three are color Photoconductor Units .
Replacing Consumables and Maintenance Kit 12 1 C Lift and ho ld the green hand le at the top ( A A A A ), and pull out the unit slowly ( B B B B ). H Install a new Photocond uctor Unit. For black, install one, and for color, install three. A Take the unit out from the bag.
Replacing the Photoconductor Unit 13 1 E Remove the co ver and pu sh in the Photoconductor Unit until it stops. I Lower the inn er cover slow ly. J Tighten two screw s using prov id- ed screwdriver . Note ❒ Be sure to return the provided sc rewd riv er to its or igi nal po si- tion on th e back of the fron t cov- er.
Replacing Consumables and Maintenance Kit 14 1 Replacing the Development Unit If "Repla ce Blac k Dev. Unit( TypeD)" appears on the panel display, replac e the black Development Unit. Replace Black Dev. Unit(Typ eD) If "Replace Color Dev.
Replacing the Development Unit 15 1 F Lift the inner cover until it clicks into place and holds. The Development Unit is installed shown in the illus tration. Starting from the u pper left, the units are attach ed in the orde r of blac k (K), yellow (Y), cyan (C) , and magenta (M).
Replacing Consumables and Maintenance Kit 16 1 B Insert the Developmen t Unit along the rail, and push in slowly until it stops. C Holding the Develop ment Unit, pu ll out the ta pe slowly in a level manner. Important ❒ Be sure to pull out th e tape to avoid printer malfunc tion during operation.
Replacing the Development Unit 17 1 L Close the front cover slow ly by pushing the two areas on the left and right. M Plug in the p ower cable and turn on the power sw itch. "Please Wait " appears on the panel display, an d initial adj ustmen ts begin.
Replacing Consumables and Maintenance Kit 18 1 Replacing the Fusing Unit R CAUTION: If "Replace Fusing Unit (T ype C)" ap- pears on the panel display, replace the Fusing Un it. Replace Fusin g Unit (Type C) A Turn off the power switch and unplug th e power ca ble.
Replacing the Fusing Unit 19 1 G Holding the green hand le, pull up the Fu sing Unit sl owly in the directi on of the arr ow, and then put it in a stable and level place. H Take out the new Fusing U nit from the bag and put it in a stable and level place.
Replacing Consumables and Maintenance Kit 20 1 M Close the upper left c over ( A A A A ) and push t he hand le ( B B B B ) slowly to the back until it clicks into place. N If you removed the E xternal Tray in step D , reattach it to the printer. Insert the hook s of the External Tray into the printer slits, and lower it toward y ou.
Replacing the Fusing Unit 21 1 S Confirm that the following mes- sage is displayed on the panel d is- play, and then load the A3 paper which comes w ith the Fu sing Unit in the Bypass Tray. Set Sheet in Bypass, then # A Open the Bypass Tray. B Pull out the Byp ass Tray Exten- sion, and then flip it open.
Replacing Consumables and Maintenance Kit 22 1 U Check the tes t sheets and selec t the correction value for A thro ugh H. • Select "1", if black and magenta square overlap sharply and you can see white slits as the sample.
Replacing the Dustproof Filter 23 1 Replacing the Dustproof Filter The dustproof fil ter is attached to the black D evelopment Un it. When re- placing the black Develop ment Unit, also replace the dustp roof filter. The dustproof fil ter is attached to the left side of the printer shown in the il- lustration .
Replacing Consumables and Maintenance Kit 24 1 E With the h and wearing the glove, take out the dustproof filter that is attached to the dustproof filter cover slow ly, one by one, and put them into the box which co n- tained the black Developm ent Unit.
Replacing the Waste Toner Bottle 25 1 Replacing the Waste Toner Bottle If "Replace Waste Toner (Type E)" ap- pears on the panel display, replace the was te to ner b ottl e. Replace Waste Toner (Type E ) A Turn off the power switch and unplug th e power ca ble.
Replacing Consumables and Maintenance Kit 26 1 G Insert the new waste toner bottle in the position shown in the illus- tration. H Push it in until it stops. Important ❒ Be sur e to i nsert th e wast e ton er bottle firmly to a void the toner from leaking inside the printer.
Replacing the Paper Feed Rollers 27 1 Replacing the Paper Feed Rollers R CAUTION: Note ❒ The following illustrations are the an examples of replacing the paper feed rollers o f Tray 1. The same procedure is followed w ith the othe r tray s. A Check the content s of the box.
Replacing Consumables and Maintenance Kit 28 1 E While pu shing the pin of the pa - per feed r olle r A outwar ds ( A A A A ), remove the paper feed roller ( B B B B ). F Remove the stopper f rom the pa- per feed roller B ( A A A A ), and remove the paper feed roller ( B B B B ).
Replacing the Paper Feed Rollers 29 1 J Hold the new paper feed roll er A with its pin towards you ( A A A A ). In- sert the roller onto the fro nt shaft until it clicks into place ( B B B B ). K Slide all trays back in to the print- er slowly until it stops.
Replacing Consumables and Maintenance Kit 30 1.
31 2. Clearing and Adjusting the Printer Cautions to Take When Cl eaning R WARNING: R CAUTION: Clean the printer periodically to maintain fine printing. Dry wipe the exteri or with a soft clot h. I f dry wipi ng is not enough, wip e with a soft, wet cloth that is wrung out well.
Clearing and Adjusting the Printer 32 2 Cleaning the Registration Ro ller R CAUTION: Clean the r olle r when r eplac ing t he black Development Unit. A Turn off the power switch and unplug th e power ca ble. B Open the righ t cover shown in the illustration.
Cleaning the DustProof Glass 33 2 Cleaning the DustProof Glass The dustproof glass may require cleaning if white lines a ppear on the print side of th e docum ent. A Turn off the power switch and unplug th e power ca ble. B Open the fr ont cover and rem ove the cleanin g brush.
Clearing and Adjusting the Printer 34 2 Adjusting the Color Registration When the printer i s moved, wh en the Fusing Unit is replaced, or after print- ing repeated ly for som e tim e, regis- tration shif ting mi ght occur. B y performi ng colo r regist ration ad just- ment, you can main tain o ptim um print resu lts.
Adjusting the Color Registration 35 2 Automatic color adjustment takes about two min utes. When it com- pletes, a check mes sage i s dis- played, and the display is returned to the co lor adjustment menu. Completed Color Regist. : Auto Adjust G When y ou have made all th e set- tings, press { { { { On Line } } } } .
Clearing and Adjusting the Printer 36 2 D Press { { { {U U U U} } } } or { { { {T T T T} } } } to display "Fus- er Adjust", and then press { { { { Enter } } } } .
Adjusting the Color Registration 37 2 When color shifting occurs Perform this procedure when colo r shifti ng occurs even afte r performing "Auto Adjust ". A Load A4 L L L L or larger paper in the Bypass Tray. Note ❒ Be sure to select paper size in the "Paper Input" menu .
Clearing and Adjusting the Printer 38 2 Note ❒ The current resolution is di s- played on the printer driver properties. ❒ To adjust the co lor regi stration on thick paper, select "Thick: 600dpi" r egardless of the cu r- rent resolution.
Adjusting the Color Registration 39 2 D Press { { { {U U U U} } } } or { { { {T T T T} } } } to di spla y "M an - ual Adjust", and then press { { { { En- ter } } } } . Color Regist. : Manual Adjust E Confirm that "Print" is displayed in the menu for printing the Test Sheet, and then press { { { { Enter } } } } .
Clearing and Adjusting the Printer 40 2 Test Sheet Sampl es Following images are samples for the test sh eet. ❖ ❖ ❖ ❖ ColorR egistS heet ❖ ❖ ❖ ❖ Fuser A djust She et I.
Adjusting the Color Registration 41 2 ❖ ❖ ❖ ❖ Fuser A djust She et II.
Clearing and Adjusting the Printer 42 2 Adjusting the Image Density Adjust the image density when the print side of the page is a hazy gray or the print image looks patchy.
Adjusting the Registration of the Trays 43 2 Adjusting the Registration of the Trays You can adjust the registrat ion of each tr ay. The ve rtical adju stment i s used for all trays.
Clearing and Adjusting the Printer 44 2 C Press { { { {U U U U} } } } or { { { {T T T T} } } } to display the tray to adjust, and then press { { { { Enter } } } } . Adjustment: Vert.: Tray 3 D Press { { { {U U U U} } } } or { { { {T T T T} } } } to set the dig- it of the registration value (mm).
45 3. Appendix Removing Misf ed Paper in the Duplex Feed Unit You can remove misfed paper from the Du plex Feed Unit following th e procedure below. Note ❒ When a paper misfeed occ urs in the Duplex Fe ed Unit, the prin ter usually sends the misfed paper to the right cover and there is no need to exe cute follow ing pro cedure.
Appendix 46 3 E Pinch the up per lef t a rea of t he Duplex Feed U nit, and pull it o ut slowly halfway. F Holding the Duplex Feed Unit firmly with both ha nds, pull it straight out. G Place the Duple x Feed Unit on th e floor slowly. Op en it slowly, and remove the misfed paper.
Removing Misfed Paper in the Duplex Feed Unit 47 3 Note ❒ Be sure to return the provided sc rewd riv er to its or igi nal po si- tion on the i nside of the f ront cover. K Close the front cover slow ly by pushing the two areas on the left and right.
Appendix 48 3 When the Front Cover Does Not Close When "Close Front Cover" appears on the panel display, even i f the cover seems to be closed properly, it is not. Close Front Cover When the front co ver does not close, confirm that the Transfer U nit is at- tached firmly.
When the Front Cover Does Not Close 49 3 E Close the front cover slow ly by pushing the two areas on the left and right. F Plug in the p ower cable and turn on the power sw itch.
Appendix 50 3 Consumables R CAUTION: ❖ ❖ ❖ ❖ Toner cartridge *1 A4 5% test chart Note ❒ The actu al number of p rinted pages you get from a particular to ner car- tridge depends on the type and size of pap er you are using, the c ontents of your print images, a nd printing environment conditions.
Consumables 51 3 ❖ ❖ ❖ ❖ Other consumables Note ❒ Actual life of consumables depends on the type and size of paper you are using, the contents of your print images, and printing environment condi- tions. All that means that consumabl es might require repl acement sooner than the life indicated.
Appendix 52 3 Paper Recommendations Loadin g Paper Important ❒ Do not use paper that is meant for an ink-jet print er or it may stick to the Fu s- ing Unit and cause a p aper misfeed. ❒ When printing on an OHP trans parency that has a prin t side, load it with the print side over on the Bypass Tray.
Paper Recommendations 53 3 ❖ ❖ ❖ ❖ Thick Paper • Use th e Byp ass Tra y. • The Bypass Tray can hold paper up to 135 kg (163 g/m 2 ) in weight. The print quality on paper that is thicker cannot be guaran teed. • Confirm that the top of the stack is not higher than the limit mark inside the t ray .
Appendix 54 3 ❖ ❖ ❖ ❖ Envelopes • When printing on envelope s, use the Bypass Tray. • Specifications of envelope s are as follows: • You can loa d up to 10 env elo pes (7 2 - 92 g/m 2 , 19 - 24 l b) in the Bypas s Tray at the same tim e, witho ut forcibly pressin g them.
Paper Recommendations 55 3 Printabl e Area The following shows the printable area for this printer. Be s ure to set the print ma rgi ns co rre ctl y by t he a pp lica tio n. A : printable area Note ❒ The printab le area may vary depending on the paper si ze, printer language and print er driver settings.
56 UE USA G060 INDEX A Adjusti ng the Color Registra tion , 34 Auto Adj ust , 34 Manual Adju st , 38 Adjusting the Image Density , 42 Adjusting the Regi stration o f the Tr ays , 43 Appendix , 45 C Ca.
Copyri ght © 2001.
UE USA G060-692 0.
Ein wichtiger Punkt beim Kauf des Geräts Savin SLP38C (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Savin SLP38C noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Savin SLP38C - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Savin SLP38C reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Savin SLP38C erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Savin SLP38C besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Savin SLP38C verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Savin SLP38C. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Savin SLP38C gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
