Benutzeranleitung / Produktwartung ML-4050ND des Produzenten Samsung
Zur Seite of 110
.
This manual is provided for information purposes only . All information included herein is subject to change without notice. Sam sung Electronics is not responsible for any direct or indire ct damages, arising from or related to use of this manual. © 2007 Samsung Electronics Co.
C ONT ACT SAMSUNG WORLD WIDE If you have any comments or questions regarding Samsung products, contact the Samsung customer care center . Country Customer Care Center We b S i te ARGENTINE 0800-333-3733 www .s amsung.com/ar AUSTRALIA 1300 362 603 www .
C ONTENT S 1. Introduction Special features ...... ....................... ................... .................... ...................... .................... ................. .................... ... 1.1 Printer overview ...... ....................
9. Troubleshooting Clearing paper jams ................. ......................... ....................... ......................... ................. ..................... ................ 9.1 Troubleshooting checklist ............ ... ..............
i Safety and Regulatory Information Import an t Precautions and Safety Information When using this machine, these basic safety precautions should always be followed to reduce risk of fire, electric shock, and injury to people: 1 Read and understand all instr uctions.
ii When using this product, these bas ic safety precautions should always be followed to reduce risk of fire, elec tric shock, and injury to persons: Ozone Safety During normal operation, this machine produces ozone. The ozone produced does not present a hazard to the operator .
iii Canadian Radio Interference Regulations This digital app ar atus does not exceed the Class A limits for radio noise emissions from digital apparatus as set out in the interference-causing equipment standard entitled “Digital Apparatus”, ICES-003 of the Industry and Science Canada.
iv EU In France, the frequency range is restr icted to 2446.5-2483.5 MHz for devices above 10 mW transmitting power such as wireless EEA/EFT A countries No limitations at this time. Regulatory Compliance St atements Wireless Guidance Low power , Radio LAN type devices (radio frequency (RF) wireless communication devices), operating in the 2.
1 .1 < Introduction> 1 Introduction Congratulations on the purchase of your printer! This chapter includes: • Special features • Printer overview • Finding more information • Selecting a location Special features Y our new printer is equipped with seve ral special features that improve the print quality .
1 .2 < Introduction> Save time and money • This printer allows you to use toner save mode to save toner . See page 2.6. • Y ou can print on both sides of the paper to save paper ( double-sid ed printing ). • Y ou can print multipl e pages on a single sheet o f paper to save paper ( N-Up printing ).
1 .3 < Introduction> Printer overview Front view 1 output tray 8 handle 2 control p anel 9 p aper level indicator 3 control boar d cover 10 multi-purpose tray 4 tray 1 11 top cover 5 optional tr.
1 .4 < Introduction> Control p anel overview 1 Menu : Enters Menu mode and scrolls through the available menus. 2 Scroll buttons: Scroll through the options avail able in the selected menu, and increa se or decrease values. 3 OK : Confirms t he selection on the display .
1 .5 < Introduction> Selecting a location Select a level, stable place with adequa te space for air circulation. Allow extra space for opening covers and trays. The area should be well-ventilate d and away from direct sunlig ht or sources of heat, cold, and humidity .
2 .1 < System setup> 2 System setup This chapter shows menus you can set and provides basic settings for your printer . This chapter includes: • Using control panel menus • Menu overview •.
2 .2 < System setup> Menu overview The control panel menus are used to configure the printer. The control panel provides access to the foling menus. The menus in th e colored characters appe ar only when the op tional items are installed. a. Available with an optional hard disk.
2 .3 < System setup> Layout menu Use the Layout menu to define all settings relating to output. Item Explanation Orientation Choose the default orient ation of the print image on the page. Simplex Margin Set the margin of print materials for one-sided printing.
2 .4 < System setup> Graphic menu Use the Graphic men u to change settings affecting the quality of the printed characters and images. System Setup menu Use the System Setup menu to configure a vari ety of printer features. Item Explanation Resolution S pecify the number of dots printed per inch (dpi).
2 .5 < System setup> Emulation menu Use the Emulat ion menu to configure prin ter language emulation. PCL This menu sets the PCL emulation configuration. Y ou can set the font type, symbol type, lines per page, and font size. Item Explanation Emulation Ty p e The printer language defines how the computer communicates with the printer .
2 .6 < System setup> Network menu This menu lets you configure the network interface installed in your printer . Y ou can reset the ne twork interface and print a configuration page. For details, see page 4.1. Item Explanation TCP/IP This item allows you to manually set the TCP/IP addresses or receive the a ddresses from the network.
3 .1 < Software overview> 3 Software overview This chapter gives you an overview of the sof tware th at comes with your printer . Further details about installing and using the software are explained in th e Software section .
3 .2 < Software overview> Printer driver features Y our printer drivers support th e following standard features: • Paper source selection • Paper size, orientation and media type • Number of copies In addition, you can use various spec ial printing features.
3 .3 < Software overview> Linux Macintosh Item Requirements Operating system • Red Hat 8.0 ~ 9.0 • Fedora Core 1 ~ 4 • Mandrake 9.2 ~ 10.1 • SuSE 8.2 ~ 9.2 Processor Pentium IV 1 GHz or higher RAM 256 MB or higher Free disk page 1 GB or higher Software • Linux Kernel 2.
4 .1 < Network setup> 4 Network setup This chapter gives you st ep-by-step instructions for setting up your printer for network connections. This chapter includes: • Introduction • Supported.
4 .2 < Network setup> Supported operating systems The following table shows the network environments supported by the printer: • IPX/SPX: Internet Packet eXchange/Sequenced Packet eXchange •.
4 .3 < Network setup> Configuring IPX frame types T o use IPX/SPX protocol networks (f or example, Novell NetW are), the format of the netw ork communicatio n frames must be specified for the printer . In most cases, you can keep the Auto setting.
5 .1 < Loading pri nt media> 5 Loading print media This chapter will help you understand types of paper you can use with your printer and how to properly load paper in the different p ape r trays for the best print quality .
5 .2 < Loading pri nt media> Supported sizes of p aper Print media for duplex prin ting Ty p e Si ze Dimensions Wei gh t a a. If media weight is over 28 lb (105 g/m 2 ), use the multi- purpose tray . Capacity b b. Ma ximum capacity may dif fer depending on media weight, thickness, and environmental conditions.
5 .3 < Loading pri nt media> Guidelines for selecting and storing print media When selecting or loadi ng paper , envel opes, or other print media , keep these guidelines in mind: • Always use print media that conform with the spe cifications listed on the next column.
5 .4 < Loading pri nt media> T ransparencies • T o avoid damaging the printer , use only transparencies designed for use in laser printers. • T ransparencies used in the printer must be able to withstand 195° C (383° F), the printer ’s fusing temperature.
5 .5 < Loading pri nt media> Using the st andard tray or the optional trays Load the print media you use for the majority of your print jobs in the standard tray . The standard tray can hold a maximum of 500 sheets of 75 g/m 2 (20 lb) paper . T o load paper , pull open the tray an d load paper with the side to be printed on face down.
5 .6 < Loading pri nt media> Using the multi-purpose tray The multi-purpose tray can hold specia l sizes a nd types of print media, such as transparencies, postcards, note cards, and enve lopes. It is useful for single page printing on letterhead or colored paper .
5 .7 < Loading pri nt media> 4 Squeeze the multi-purpose tray paper width guides and adjust them to the width of the paper . Do not force too much, or the pa p er will be bent, which will result in a paper jam or skew . 5 When you print a document, set the paper sou rce and type i n the software application.
5 .8 < Loading pri nt media> Selecting an output location The printer has two output locations; the rear cover (face up) and the output tray (face down). The printe r sends output to the outpu t tray by de fault. T o use the output tray , make sure that the rear cover is closed.
6 .1 < Basic printing > 6 Basic printing This chapter explains common printing tasks. This chapter includes: • Printing a docu ment • Canceling a print job Printing a document This printer allows you to print from various Windows, Macintosh, or Linux applications.
7 .1 < Ordering supplies and a ccessories> 7 Ordering supplies and accessories This chapter provides information on purchasing tone r cartridges and accessories a vailable for your pr inter .
7 .2 < Ordering supplies and a ccessories> How to purchase T o o rder Samsung-authorize d supplies or acce ssories, contact your local Samsung dealer or the retailer where you purchased you r printer , or visit www .samsungprinter .co m and select your country/region for information on calling for technical supp ort.
8 .1 < Maintenanc e> 8 Maintenance This chapter provides information for maintaining your printer and the toner cartridge, as well as suggestions for high-quality and economica l printing.
8 .2 < Maintenanc e> 2 Open the top cover and pull the t oner cartridge out. Set it on a clean flat surface. 3 With a dry lint-free cloth, wipe aw ay any dust and sp illed toner from the toner cartridge area and the tone r cartridge cavity .
8 .3 < Maintenanc e> Printing a cleaning sheet If you are experiencing blurre d, fade d, or smeared printouts, you can clear the problem by printing a cleani ng sheet, provided by your pri nter . Y ou can print: • OPC cleaning sheet: cleans the OPC drum of the toner cartridge.
8 .4 < Maintenanc e> Redistributing toner cartridge When the toner cartridge is near the end of its life: • White streaks and light printing occur .
8 .5 < Maintenanc e> Replacing the t oner cartridge • T oner Empty appears on the display . •T h e Statu s LED lights red. At this stage, the toner cartridge needs to be replaced. For order information for toner cartridges, see page 7.1. 1 Open the top cover .
8 .6 < Maintenanc e> 6 Remove the flex ible plastic holder ou t of the toner cartridge. 7 Hold the toner cartridge by th e handle and slowly insert th e cartridge into the o pening in the printer .
9 .1 < Troubleshooti ng> 9 Troubleshooting This chapter provides he lpful informat ion for what to do if you encounter an error while using your printer .
9 .2 < Troubleshooti ng> In the p aper feed area In the tray 1 1 Pull the tray 1 open. 2 Remove the jammed paper by gently pulling it straight o ut.
9 .3 < Troubleshooti ng> In the multi-purpose tray 1 If the paper is not feeding properly , pull the paper out of the printer . 2 Open and close the top cover to resume printing. Around the toner cartridge 1 Open the top cover and pu ll the toner cartridge out.
9 .4 < Troubleshooti ng> 5 Replace the toner cartridge and close the top cover . Printi ng automatically resumes. In the p aper exit area 1 Open and close the top cover . The jammed paper is automatically ejected from the printer . 2 Gently pull the paper out of the ou tput tray .
9 .5 < Troubleshooti ng> Duplex jam 1 1 Open the rear cover . 2 Gently pull the jammed paper straight up. 3 Close the rear co ver . 4 Open and close the top cover . The printer will resume printing. Tip s for avoiding paper jams By selecting the correct media types, most paper jams can be avoide d.
9 .6 < Troubleshooti ng> Underst anding the status LED Stat us Description Off • The printer is powerd off. Green On The printer is on-line and can receiv e data from the computer . Blinking • When the backlight blinks slowly , the printer is receiving data from the computer .
9 .7 < Troubleshooti ng> Load [Size] In [T ray] The paper size specified in the printer prop erties does not match the paper you are loading. Load the correct paper in the tray . Load Manual Press Stop Key The multi-purpose tray is empty in manual feed mode.
9 .8 < Troubleshooti ng> T oner cartridge-related messages Message Meaning Suggested solution s Install T oner The toner cartridge is in stalled improperly , or not installed. Reinstall the toner cartridge two or three times. If the problem persists, the toner cartridge is not being detected.
9 .9 < Troubleshooti ng> Solving general printing problems For problems with the operation of yo ur printer , refer to the table for suggested solutions. Condition Possible ca use Suggested solutions The printer does not print. The printer is not receiving power .
9 .10 < Troubleshooti ng> Print job is extremel y slow . (Continued) If using Windows 98/Me, the S pooling Setting may be set incorrec tly . From the Star t menu, choose Settings and Printers . Right- click the Samsung ML-4050 Series PCL 6 printer icon, choose Pr operties , click the Details t ab , and then choose the Spool Settings button.
9 .11 < Troubleshooti ng> Solving print quality problems Dirt inside of the printer or improper paper loading may reduce print quality . See the table below to troubleshoot problems. PDF file does not print correctly- some part s are missing in the graphics, text or illustrations.
9 .12 < Troubleshooti ng> Ve r t i c a l repetitive defects If marks repeatedly appear on the prin ted side of the page at even intervals: • The toner cartridge may be damaged. If a repetitive mark occurs on the page, print a cleaning sheet several times to clean the cartridge; see page 8.
9 .13 < Troubleshooti ng> Common Windows problems Charac ter V oids Character voids are white area s within characters that should be so lid black: • If you are using transparencies, try another type of tr ansparency . Because of th e composition of the transparency , some character voids may be normal.
9 .14 < Troubleshooti ng> Common Linux problems A PostScript error page prints. Print job may not be PostScript. Make sure that the print job is a PostScript jo b. Check to see whether the software application expected a setup or PostScript header file to be sent to the printer .
10 .1 < Installing accessories> 10 Installing accessories Y our printe r is a full-featured laser printer th at has been opti mized to meet the majority of your printing needs. Recognizing th at each user may have different requirements, however , Samsung makes several accessories available to enhance th e printer ’s capabilities.
10 .2 < Installing accessories> 3 Grasp the control board cove r and remove it. 4 Completely open the latches on ea ch side of the DIMM slot. 5 Remove the memory DIMM from its antist ati c package. Locate the alignmen t notches on the bottom edge of the DIMM .
10 .3 < Installing accessories> Removing a DIMM T o expand the printer memory to 512 MB, you need to re move the preinstalled 64 MB DIMM and install two 256 MB DIMMs into the DIMM slots. Push the latches at both ends of the DIMM slot away to remove the DIMM and pull out the DIMM.
10 .4 < Installing accessories> 5 Close the control board cover by al igning the groo ve on it with the notch on the p rinter and sliding it. 6 Reinstall the duplex-slot cover or the duplex unit. 7 Reconnect the power cord and pr inter cable (if necessary), and turn the printer on.
10 .5 < Installing accessories> Setting Encryption If your network uses WEP encryptio n keys, you can must select the appropriate encryptio n type and configure encryption keys.
10 .6 < Installing accessories> 4 Align the connector on the hard disk with the connector on the control board. Push the hard disk in until it is latched into place. 5 Fasten the fo ur screws supplied with yo ur new hard disk. 6 Close the control board cover by al igning the groo ve on it with the notch on the p rinter and sliding it.
10 .7 < Installing accessories> 1 Open the file you wa nt to store. 2 Select Print from the File menu. The Print window displays. 3 Click Properties . If you see Setup , Print or Optio ns , click the button instead. 4 Click the Extra tab and click Print and H old .
10 .8 < Installing accessories> T o promote a file from the queue : Y ou can select a job waiting in the Active Job Que ue and change its print order so that it can be printed sooner . 1 Press Menu until Job Manage. app ears on the bottom line of the display and press OK .
11 .1 < Specifications> 11 Specifications Printer specifications Item Specificat ions and Description Printing speed a Up to 38 ppm in A4 (41 p pm in Letter) Duplex: 26 ipm in A4 (27 ipm in Lett.
1 I NDEX A accessories installing DIMM 10.1 hard disk 10.5 network interface card/device 10.3 order information 7.1 C cleaning drum 8.3 inside 8.1 outside 8.1 cleaning sheet, print 8.3 component location 1.3 control panel buttons 1.4 menus 2.1 status LED 9.
2 R rear cover, use 5.8 redistributing, toner cartridge 8.4 replacing, toner cartridge 8.5 , 8.6 S special print media, guid elines 5.3 specification, printer 11.1 status LED, meaning 9.6 supplies checking life 8.3 order information 7.1 system requirements Linux 3.
Samsung Printer Software section.
1 S OFTWARE SECTION C ONTENTS Chapter 1: I NSTALLING P RINTER S OFTWARE IN W INDOWS Installing Printer Software .............. ................... ................ ... ................... ................ ... ......... ..... 4 Installing Software for Local Printing .
2 Creating a Watermark .................. ................... ................... ................. ................... ....... 21 Editing a Watermark .......... ................... ................... ................... ................... .........
3 Getting Started .............. ................... ................. ................... ................... ................... .... .... . . 28 Installing the Unified Li nux Driver ...... ................... ................... ................. .
Installing Printer Software in Windows 4 1 Installing Printer Software in Windows This chapter include s: • Ins talling Printer Software • Reinstalling Print e r Software •R e m o v i n g P r i n t e r S o f t w a r e Installing Printer Software Y ou can install the printer software for lo cal printing or network printing.
Installing Printer Software in Windows 5 4 Select Typical inst allat ion for a local pr in te r . Click Next . N OTE : If your printer is not already connected to the computer , the following window w ill appear . • After conne ct ing the printer , click Next .
Installing Printer Software in Windows 6 2008 R2, click Start → All Programs → Accessories → Run , and type X:Setup.exe . 3 Click Next . • If necessary , select a langua ge from the drop-down l ist. • View User’s Guide : Allows you to view the User’ s Guide.
Installing Printer Software in Windows 7 6 Select the components to be installed and click Next . N OTE : Y ou can change the desire d installation folder by clicking [ Browse ]. 7 After the installation is fini shed, a window asking yo u to print a test page appears.
Installing Printer Software in Windows 8 2 Insert the supplied CD-ROM into your CD-ROM drive. If you use Windows Vista, Wi ndows 7 and Windows Server 2008 R2, wh en y ou are asked to allow the insta llation, click continue . The CD-ROM should automaticall y run, and an installation window appears.
Installing Printer Software in Windows 9 Custom Installation Y ou can choose individual components to install and set a specific IP address. 1 Make sure that the printer is connected to y our network and powered on. F or details about connecting to the network, see the supplied pr inter’ s User’s Guide.
Installing Printer Software in Windows 10 T IP : If you want to set a specific IP address on a specific network printer , click the Set IP Address button. The Set IP Address window appear s. Do as follows: a. Select a printer to be set wi th a specific IP addres s from the list.
Installing Printer Software in Windows 11 Reinstalling Printer Software Y ou can reinstall the software if installation fails. 1 Start Window s. 2 From the Start menu select Programs or All Progr ams → your prin ter driver name → Maintenance . 3 Select Repair and click Next .
Installing Printer Software in Windows 12 Removing Printer Software 1 Start Window s. 2 From the Start menu select Programs or All Progr ams → your prin ter driver name → Maintenance . 3 Select Remove and click Next . Y ou will see a component list so that you ca n rem ove any item individually .
Basic Printing 12 2 Basic Printing This chapter explains the printing options and common printing tasks in Windows. This chapter include s: • Printing a Documen t •P r i n t e r S e t t i n g s - .
Basic Printing 13 Printer Settings Y ou can use the printer properties window , which allows you to access all of the printer options you need when using yo ur printer . When the printer prop erties are displayed, y ou can review and change the settings neede d for your print job.
Basic Printing 14 Paper Tab Use the following options to set the basic paper handling specifications when you access the p rinter properties. See “Printing a Document” on page 12 for more information on accessing printer properties. Click the Paper tab to access v arious paper properties.
Basic Printing 15 Graphics Tab Use the following Gr aphic options to adjust the print quality for your specific printing needs. See “Printing a Document” on page 12 for more information on accessing printer prop erties. Click the Graphic tab to display the properties shown below .
Basic Printing 16 Extras Tab Y ou can select output options fo r your document. See “Printing a Document” on page 12 for more information about accessing the printer properties. Click the Extras tab to access the following feature: Watermark Y ou can create a background text image to be printed on each page of your document.
Basic Printing 17 About Tab Use the About tab to display the copyright notice and the version number of the driver . If you have an Internet browser , you can connect to the Internet by clic king on the web site icon. See “Printing a Document” on page 12 for more information about accessing printer properties.
Advanced Printing 18 3 Advanced Printing This chapter explains printing options and adv anced printing tasks. N OTE : • Y our printer driver Propertie s window that appears i n this User’s Gu id e ma y differ depending on the printer in use. However the com position of the printer properties window is similar .
Advanced Printing 19 Printing Posters This feature allows you to print a single-pag e document onto 4, 9, or 16 sheets of paper , for the purpose of p asting the sheets together to form one poster-size d ocum ent. 1 T o change the print settings from your softw are application, access printer propertie s.
Advanced Printing 20 Printing on Both Sides of Paper Y ou can print on both sides of a sheet of paper . Before printing, decide how you want yo ur docum ent oriented. The options are: • Printer Setting , if you select this option, this feature is determined by the setting you’ve made on the control panel of the printer .
Advanced Printing 21 Using Watermarks The W aterm ark option allows you to print text over an existing document. F or example, you may want to hav e large gray letters reading “DRA F T” or “CONFID ENTIAL ” printe d diagonally across the first page or all pages of a document.
Advanced Printing 22 Using Overlays What is an Overlay? An overla y is text and/or images stored in the computer hard disk drive (HDD) as a special file fo rmat that can be printed on any document. Ove rla ys are often used to take the place of preprinted forms and lette rhead p aper .
Using Windows PostScript Driver 23 4 Using Windows PostScript Driver If you want to use the P ostScri pt driver provided with y our system CD-ROM to print a document. PPDs, in combina tion with t he Po stScript driver , access printer features and allow the computer to communicate with the printer .
Using Direct Print Utility 24 5 Using Direct Print Utility This chapter explains how to use Dir ect Print Utility to print PDF files without having to open the files. C AUTION • Y ou can not print PDF files that are restricted to print. Deactivate the p rinting restriction feature, and retry printing.
Sharing the Printer Locally 25 6 Sharing the Printer Locally Y ou can connect the printer dire ctly to a selected computer , which is called “host computer , ” on the network. The following procedure is for Windows XP . For other Windows OS, refer to the correspon ding Wi ndows User's Guide or online help.
Using Smart Panel 26 7 Using Smart Panel Smart P anel is a progr am that mo nitors and informs y ou of the status of the printer , and allow s y o u to customiz e the printe r’ s settings. If you are a Windows or Macintosh OS user , Smart P ane l is installe d automatically when you install the printer software.
Using Smart Panel 27 instead of the Printer Settings Utility window . Mac OS X and Linux do not support network environments. Driver Setting (Only for Windows) Y ou can use the printer properties window , which allows you to access all of the printer options you need for using yo ur printe r .
Using Your Printer in Linux 28 8 Using Your Printer in Linux Y ou can use your machine in a Linux environment. This chapter include s: • Getting Started • Ins tall in g the Un i fie d Linux Driver.
Using Your Printer in Linux 29 6 When the installation is complete , click Finish . The installation prog r am has added the Unified Driv er Configurator desktop icon and Samsung Unified Drive r group to the system menu for your conv enience.
Using Your Printer in Linux 30 Using the Unified Driver Configurator Unified Linux Driv er Configurator is a to ol primarily intended for configuring Printer. After installing the Unified Linux driver , the Unified Linux Driver Configur ator icon will automatically be created on your desktop.
Using Your Printer in Linux 31 Classes Tab The Classes tab shows a list of available printer classes. • Refresh : Renews the classes list. • Add Class... : Allows you to add a new printer class. • Remove Class : Remo ves the selected printer class.
Using Your Printer in Linux 32 Printing a Document Printing from Applications There are a lot of Li nux applications that you are all owed to print from using Common UNIX Printing System (CUPS). Y ou can print on your machine from an y such application .
Using Your Printer with a Macintosh 33 9 Using Your Printer with a Macintosh Y our machine supports Macintosh systems with a built-in USB interface or a 10/100 Ba se- TX network interface card. When you print a file from a Macint osh computer , you can use the P o stS cript driver by installing the PPD file.
Using Your Printer with a Macintosh 34 Setting Up the Printer Set up for your prin ter will be diff erent de pending on whi ch cable you use to connect the pr inter to y our computer—the network cable or the USB cable. For a Network-connected Macintosh N OTE : Some printers do not support a network interface.
35 Printing N OTES : • T he Macintosh printer’ s proper ties window that appears in this User’s G uide may differ d epending on the printer in use. However the com position of the printer properties window is similar . • You can check your printer name in t he supplied CD- ROM.
36 Printer Features Setting The Printer Features tab provides options for selecting the paper type and adjusti ng prin t quality . Select Printer Feature s from the Presets drop-down list to access the following features: Reverse Duplex Allows you to select general prin t order compare to duplex print order .
37 Duplex Printing Y ou can print on both sides of the paper . Before printing in the duplex mode, decid e on which edge you will be bind ing y our finished document. Th e binding options ar e: Long-Edge Binding : Which is the conventional layout used in book bi nding.
38 S OFTWARE SECTION I NDEX A advanced printing, use 18 B booklet printing 19 D document, print Macintosh 35 Window s 12 double-sid ed printin g 20 E Extras properties, set 16 F favorites set tin gs, .
39 image mode 15 resolution Macintosh 36 Window s 15 toner save 15 true-type option 15 software install Macintosh 33 Window s 4 reinstall Window s 10 system requ irements Macintosh 33 uninstall Macint.
GGGGGGGGGGGGG Rev . 9 .00.
Ein wichtiger Punkt beim Kauf des Geräts Samsung ML-4050ND (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Samsung ML-4050ND noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Samsung ML-4050ND - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Samsung ML-4050ND reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Samsung ML-4050ND erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Samsung ML-4050ND besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Samsung ML-4050ND verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Samsung ML-4050ND. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Samsung ML-4050ND gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
