Benutzeranleitung / Produktwartung ML 3560 des Produzenten Samsung
Zur Seite of 124
.
This manual is provided for inf orm ation purposes only . All inform ation included herein is subjec t to change without notice. Sam sung Electronics is not responsible for any ch anges, direct or indirect, arising fr om or related to use of this manual.
ii Contact SAMS UNG WORLD WIDE If you have any comments or questions regar ding Samsung products, contact the SAMSUNG custom er care center . Countr y Custom er Care Cen ter Web S ite CANADA 1-800-SAMSUNG (7267864) www .samsun g.com/ca MEXICO 01-800-SAMSUNG (7267864) ww w.
iii C ONTENTS 1. Introduction Special Feat ures ................. .... .................... .................... ................ .... .................... ......... ...... 1.1 Printer Features .................... .... .................... ..........
iv 4. Using Print Materials Choosing Pa pe r and Other Mater ials .............. ................ .... .................... .................... ............... 4. 1 Sizes and Capa cities .............. .................... .................... ......
v 8. Using Your Printer on a Network About Sharing the Printer on a Network ......... .................................... .... .................... ............... 8.1 Setting Up a Ne twork-Connecte d Printer ........................ ................
vi Important Precautions an d Safety Information When using this machine, these basic safety precautions should alw a ys be followed to reduce risk of fire, el ec tric shock, and injury to people: 1 Read and und erstand all instructions. 2 Use common sense whenever op er ating electrical appliances.
vii Power Saver This printer contains advanced energy conservation technology that red uces power consumption when it i s not in acti ve use. Whe n the pr inter doe s not rece ive da ta for an extende d period o f time, po wer consumption is auto matically lowered.
viii Declaration of Conformity (European Countries) Approvals and Certifications The CE marking applied to this prod uct symbolises Samsung Electronics Co.
ix Every country has different restri ctions on the use of wireless devices. Since your system is equipped with a wireless device, when trav eling between countries with your system, check with the local Radio Appro val authorities prior to any mov e or trip for any restrictions on the use of a wireless device in the destination country .
Introduction 1. 1 1 Introduction Congratulations on the purchase of your printe r! This chapter includes: • Special Features • Printer Comp onents Special Features Y our new printer is equipped with sever al special fea tures that improve the print quali ty .
Introduction 1. 2 Save time and money • This printer allows you to use the Toner Save mode to save toner . For details, s ee page 2.8. • Y ou can print on both sides of the paper to save paper ( double-side d pr inting ) if you install an optional duplex unit.
Introduction 1. 3 Printer Components Front View Output Tray (Face down) Control Panel (See page 3.1.) Tray 1 (500-sheet paper feeder) Paper Level Indicator Control B oard Cover (Open to install optional printer accessories .
Setting Up Your Printer 2. 1 2 Setting Up Your Printer This chapter provides step b y step information on setting up your pri nter . This chapter includes: •U n p a c k i n g • Installing th e Ton.
Setting Up Your Printer 2. 2 3 Pull the paper tra y out of the printer and remove the packing tape and the packing material inside of the tra y . Selecting a Location Select a leve l, stable place with adeq uate space for air circulation. Allo w extra space for opening covers and trays.
Setting Up Your Printer 2. 3 4 There is a flexible plastic holder . Remo v e the holder out of the toner cartridge. 5 Thoroughly shake the cartridge from side to side to distribute the toner evenly inside the car tridg e. Thoroughly shaking the cartridge will assure maximum copies per cartridge.
Setting Up Your Printer 2. 4 Loading Paper The T ray 1 can hold a maxi mum of 500 sh eets of 2 0lb plain paper . T o load a stack of A4 or Letter-sized paper : 1 Pull open the T ray 1 and remo v e it from the printer . 2 Pull down the metal plate until it lo cks into po sitio n.
Setting Up Your Printer 2. 5 7 Insert and slide the paper tr ay back into the printer . Changing the Size of the Paper in the Paper Tray The tray is preset to Le tter or A4 size , depending o n your country . T o change the size, you need to adjust the paper guides.
Setting Up Your Printer 2. 6 Connecting a Printer Cable For Local Printing T o print from your computer in a local en vironment, y ou need to connect your printer to the co m p uter with either a par allel interface cable or a Univ ersa l Serial Bus (USB) cable.
Setting Up Your Printer 2. 7 Using an Ethernet Cable 1 Connect one end of the Ethernet cable into the network port on the printer . 2 Connect the other end of th e cable into a network LAN connection. See your computer’ s User’ s Guide, if you need help.
Setting Up Your Printer 2. 8 Changing the Display Language T o change the language that is displayed on the cont rol panel, follow these st eps: 1 In ready mode, press the Menu button ( ) on the control panel until you see “S etup” on the bottom line of the display .
Using the Control Panel 3. 1 3 Using the Control Panel This chapter describe s how to u se the pr inter’s control p anel. This chapter includes: • Understandi ng the Cont rol Panel • Using Control Panel Menus Understanding the Control Panel The control panel on the top right side of y our printer has the display and the eight buttons.
Using the Control Panel 3. 2 Buttons Button Description On Line/ Continue • Pr ess to switch between on-line and off-line. • In menu mode, press to return to ready mode. Y ou can check the printer status according to th e button backlight. Green On The printer is on-line and can receive data from the computer .
Using the Control Panel 3. 3 Overview of Control Panel Menus The control panel menus are used to configure the printer . The control panel provides a cce ss to the follo w ing menus: EPSON/IBM/IBM (See page 3.8.) Fon t Auto Wrap Character Set Character T ab.
Using the Control Panel 3. 4 Paper Menu Use this menu to define all settin gs relating to print material input and output, as well as the specific print ma terial yo u are using with your printer . (*: the default setting) Item Explanation Tr a y S o u r c e Using this item, you can set the tray y ou w ill use.
Using the Control Panel 3. 5 Layout Menu Use the Layout menu to define all settings relating to output. (*: the default setting) Item Explanation Orientation Choose the default orientation of print image on the page. Duplex T o print on both sides of paper , choose the binding edge as follows.
Using the Control Panel 3. 6 Graphics Menu Use the Graphics menu to change settings affecting the quality of the printed characters and image s . (*: the default setting) Item Explanation Res o l ut i o n Specify the number of dots printed pe r inch (dpi).
Using the Control Panel 3. 7 Auto Continue This item determines whether or not the printer continues printing when it detects the paper unmatched to your paper setting. • Off : If the paper mismatch occurs, the message will remain on th e display and the printer will remain off -line until you insert the correct paper .
Using the Control Panel 3. 8 PostScript Menu This menu provides you with the Print PS Error menu item. (*: the default setting) Pitch When you select one betwe en PCL1 and PCL7 from the Typeface menu, you can determine the font size by setting the nu mber of c haracters that will print in one horizontal inch of type.
Using the Control Panel 3. 9 Network Menu This menu lets you configure the network interface card installed in your printer . Y ou can upgrade the firmw are of the network interface card and print a configuration page.
Using the Control Panel 3. 10 Config Netware Y ou can set this item only when you set Netware to On . This item lets you select whether or not you set the frame type parameter . Select Yes to select the frame type. If you select Yes , the IPX Frame Type option appears on the display .
Using Print Materials 4. 1 4 Using Print Materials This chapter will help y o u understand types of pa pe r you can use with your pri nter and how to properly l oad paper i n the different paper trays for the b est print q uality .
Using Print Materials 4. 2 • Preprinted forms must be printed with nonflammable, heat-resistant ink that does not melt, v aporize, or release hazardous emissions when subjected to the printer’s approximately 383°F (195°C) fusing temperature for 0.
Using Print Materials 4. 3 • T o prevent paper jams, do not add paper when there is still paper in the Multi-Purpose T ray . This also applies to other types of print materials. • Print materials should be loaded face up with the top edge going into the Multi-Purpose T ra y first, and be placed on the center of the tray .
Using Print Materials 4. 4 N OTE : Y our printer cannot automati cally detect the size of paper loaded in the Multi-P urpose T ray . Configuring the Multi- Purpose T ray with the correct paper size allows you to select paper by size rather than paper source when you print from your software a pplication.
Using Print Materials 4. 5 N OTE : If you do not press the button, after a pause the printer will automatically pick the print material. 6 Insert the next sheet into the Multi-Purpose T ray and press the On Line/Continue button ( ). Repe at this step for every p age to be printed.
Using Print Materials 4. 6 To open the rear cover: 1 Open the rear cov er by pulling it down . The cove r functions as the output tray . C AUTION : The fusing area inside the rear cover of yo ur printer be comes very hot when i n use. T ake care not to burn your fingers when you access this area.
Using Print Materials 4. 7 3 Push the envelope lev ers upwards. The print qualit y will be enhanced. C AUTION : Push th e envelope l evers do wnwards when you print on materials other than envelopes. 4 Flex or fan the edge of the env elope stack to separ ate and load the enve lopes into the Multi-Purpose T ray with the flap side down .
Using Print Materials 4. 8 3 Load labels into the Multi-Purpose T ray with the print side up . Adjust the guide to fit the width of the labels. 4 When you print, set the paper source, typ e, and siz e properly in the software application. F or details, see the Software Section .
Using Print Materials 4. 9 Printing on Preprinted Paper Preprinted paper is pape r that has some t ype of print ing on it before it is sent through the printer (paper that has a preprinted logo at the top of the page, for examp le). 1 Load letterheads into the tra y y o u want to use, as shown in the figures below .
Basic Printing 5. 1 5 Basic Printing This chapter explains common printing tasks. This chapter includes: • Printing a Do cument • Canceling a Print Job Printing a Document This printer allows you to print from v a rious Windows applications, a Macintosh computer , or a Linux system.
Maintaining Your Printer 6. 1 6 Maintaining Your Printer This chapter provides inform ation for m aintaining y our pr inter and the toner cartridge, as well as suggestions for high-quality and economical printing.
Maintaining Your Printer 6. 2 Maintaining the Toner Cartridge Toner Cartridge Storage T o get the maximum results from a toner cartridge, k eep the following guidelines in mind: • Do not remove the toner cartridge from its package until ready for use.
Maintaining Your Printer 6. 3 3 Thoroughly shake the toner cartri dge from side to side 5 or 6 times to distribute the toner evenly inside the cartridge. N OTE : If toner gets on your clothing, wip e it off with a dry cloth and wash clothing in cold w ater .
Maintaining Your Printer 6. 4 4 Locate the sealing tape at th e end o f the to ner ca rtrid ge. Carefully pull the tape comple tely out of the cartridge and discard it. N OTES : • T h e s e a l i n g t a p e s h o u l d b e l o n g e r t h a n 6 0 c m w h e n c o r r e c t l y removed.
Maintaining Your Printer 6. 5 Cleaning the Printer During the printing process, particles of paper , toner , and dust can accumulate inside the printer . Over time, this build-up can cause print quality problems such a s t o n e r s p e c k s o r s m e a r i n g .
Maintaining Your Printer 6. 6 4 Swa p the long s trip of gla ss (LSU ) inside the prin ter and see if di rt turns the white co tton bla ck. N OTE : The long stri p of glas s is ha rd to locate beca use it is inside th e top of t he cartrid ge compartment.
Solving Problems 7. 1 7 Solving Problems This chapter provide s helpful info rm ation for wha t to do if y ou encounter an error while using your p rinter .
Solving Problems 7. 2 Solving General Printing Problems For prob lems with the oper ation of your printer , refer to the table for suggested solutions. Problem Possible Cause Solution The printer does not print. The printer is not receiving power . Check the power cord connections.
Solving Problems 7. 3 Half the page is blank. The page layout is too complex. Simplify the page layout and remove any unnecessary graphics from the document. Install more memory in your pr inter . See “Installing Memory DIMM” on page 9.1. The page orienta tion setting may be incorrect.
Solving Problems 7. 4 Clearing Paper Jams N OTE : When removi ng paper tha t is jamme d in the pr inter , if possible always p ull the paper in the direction that it norm ally moves so as not to dam ag e internal com ponents. Always pull firmly and even ly; do not jerk the p aper .
Solving Problems 7. 5 In the Optional Tr ay 2 (Paper Jam 0) 1 Pull the optional T ray 2 out of the printer . 2 Remo ve the jammed paper from the tray . Slide the tray back into the printer . Go to step 6. If you cannot find jammed pa per , or if there is any resistance removing the paper , stop pulling and go to step 3.
Solving Problems 7. 6 In the Multi-Purpose Tray (Paper Jam 0) 1 Open the Multi -Purpose T ray . 2 Remove the jammed paper by pulling in direction shown. T o avoid tearing the paper , pull it out gently and slowly . 3 Open and close the top cover . The printer will resume printing.
Solving Problems 7. 7 In the Paper Exit Area (Paper Jam 2) 1 If a long portion of the paper is visible, pull it straight out. Go to step 5. If you cannot find jammed pa per , or if there is any resistance removing the paper , stop pulling and go to step 2.
Solving Problems 7. 8 In the Duplex Area (Duplex Jam 2) 1 Pull the duplex unit out of the printer . 2 Locate the jammed paper and remo v e it. 3 Insert the duplex unit into the slot. 4 Open and close the top cover . The printer will resume printing. Tips for Avoiding Paper Jams By selecting the correct paper types, most paper jams can be avoided.
Solving Problems 7. 9 Vertical lines If black vertical streaks appear on the page: • The drum inside the toner cartridge has probably been scratched. Install a new toner cartridge. If white vertical lines ap pear on the page: • The surface of the LSU may be dirty .
Solving Problems 7. 10 Back of printouts are dirty • The transfer roller may be dirty . “Cleaning the Inside of the Printer” on page 6.5. • Che ck for leaking toner . Clean the inside of the printer . Solid color or Black pages • The toner cartridge may not be installed properly .
Solving Problems 7. 11 Engine Fuser Low Heat Error The temperature in the fuser is abnormally low . Unplug the power cord and plug it in again. If the problem persists, call for service. Engine Fuser Over Heat Error The temperature in the fuser is abnormally high.
Solving Problems 7. 12 N OTE : When you encounter the proble ms about the o ptional hard disk, call for service. Rea d y Rep l a ce C a rt The life of some parts on the toner cartridge ends. The overflow of the waste toner contaminates the inside of the machine.
Solving Problems 7. 13 Common PS Problems The following situations are PS language specific and may occur when sever al printer languages are b eing use d. N OTE : T o receive a printed or screen displayed message when PS errors occur , open the Print Options window and click the desired selection next to the Post Script errors section.
Solving Problems 7. 14 I am using BSD lpr (Slackware, Debian, older distributions) and some options chosen in LLPR don’t seem to t ake effect. Legacy BSD lpr systems have a hard limitation on the length of the option string that can be passed to the printing sy ste m .
Using Your Printer on a Network 8. 1 8 Using Your Printer on a Network If you work in a networked environment, the printer can be shared by other users on the network. The ML -3561N a nd ML -3561ND printers are network printers and can be connected to the network via Ethernet cable.
Using Your Printer on a Network 8. 2 Configuring Network Parameters on the Control Panel Supported Operating Systems N OTE : The operating systems supp orted by the network card may be different from the operating system s supported by the printer . The following table shows the network en vironm ents supported by t he printer .
Using Your Printer on a Network 8. 3 9 Press the scroll button ( or ) until “Static” displays and press the Enter button ( ). 10 Press t he Upper Level button ( ), then use the scroll button ( ). 11 Press t he Enter button ( ) to access the IP Address menu.
Using Your Printer on a Network 8. 4 11 Press t he Enter button ( ) when “IPX Frame T ype” displays. 12 Press the scroll button ( or ) until you see the desired frame type and press the Enter button ( ). 13 Press t he On Line/Continue button ( ) to return to ready mode.
Installing Printer Options 9. 1 9 Installing Printer Options Y our printer is a full-featured laser printer tha t has been optimized to meet most of your printin g needs. R ecognizing that each user may hav e di fferent requirem ents, however , Samsung makes seve r al options available to enhance the printer ’s capabilities.
Installing Printer Options 9. 2 3 Hold the control board cover and rem ove it. 4 Completely open the latches on each side of the DIM M slot. 5 Remo ve the memory DIMM from its antistatic package. Locate the alignment notches on the bottom edge of the DIMM.
Installing Printer Options 9. 3 Removing the Memory DIMM 1 Follow steps 1 and 3 on page 9.1 to access the control board. 2 Push the latches at both ends of the DIMM slot away from the DIMM. Pull out the DIMM. 3 Place the DIMM in its original pa ckag e or wra p it w ith a sheet of thin metal, such as alum inium foil, and stor e it i n a box.
Installing Printer Options 9. 4 6 Tighten the two screws which you rem oved in step 4 or supplied with your new network card. 7 Repla ce the control boar d cover . 8 Reinstall the d u ple x-slot co ver or the optional duplex unit. 9 Connect the network cable, re connect the power cord, and then turn the printer on.
Installing Printer Options 9. 5 5 F asten the four screws supplie d with your new hard disk. 6 Repla ce the control boar d cover . 7 Reinstall the d u ple x-slot co ver or the optional duplex unit. 8 Reconnect the power cord and printer cable , and turn the printer on.
Installing Printer Options 9. 6 Printing a Stored Job Y ou can print jobs currently stored in the hard disk. 1 Press t he Menu button ( ) on the control panel until “Stored Job” appear s on the bottom line of the disp lay . 2 Press t he Enter button ( ) to access the menu.
Installing Printer Options 9. 7 To print a file im mediately : Y ou can print the print job you w ant immediately . In this case, the job currently printing is stopped and the selected job will be printed.
Installing Printer Options 9. 8 3 Find the location of the connector and the optional T ray 2 positioners. 4 Place the printer ov er the optional T ray 2, aligning the fee t on the printer with the positioners on the optional T ray 2. C AUTION : The printer weights 23kg including the to ner cartridge and the tray .
Installing Printer Options 9. 9 Installing a Duplex Unit The printer can automati cally print on both sides of a sheet of paper with an opti onal duplex uni t. This is called duplexing. The optional duplex unit supports the following paper size s: letter , legal, folio, and A4.
Specifications 10. 1 10 Specifications This chapter includes: • Printer Specificat ions • Paper Specificatio ns Printer Specifications Item Specifications and Description Model Name ML -3560 ML -3.
Specifications 10. 2 Paper Specifications Overview Y our printer accepts a variety of print materials, such as cut - sheet paper (including up to 100% recycled fiber content paper), e nvelopes, la bels, tr ansparencies, and custom-size paper .
Specifications 10. 3 N OTE : Y ou may ex perience jams when using pri nt materials with a length of less than 127 mm (5.0 in.). F or optimum performance, ensure th at you ar e stor ing and handling the paper correctly . Please refer to “Printer and P aper Storage Environment” on page 10.
Specifications 10. 4 Paper Specifications Paper Output Capacity Printer and Paper Storage Environment Paper stor age environmental conditions directly affect the fee d operation. Ideally , the printer and paper stor age environment should be at or near room temperature, and not too dry or humid.
Specifications 10. 5 Envelopes with Do uble Side Seams Double side-seams construction has vertical seams at both ends of the env e lope ra ther tha n diagonal seams. This style may be more lik ely to wrinkle. Be sure the seam extends all the way to the corner of the en velope as illustrated below .
1 I NDEX A antenna, connect 2.7 C card stock, print 4.9 clean inside 6.5 outside 6.5 cleaning sheet, print 6.6 components 1.3 configuration page, print 6.1 connect ethernet 2.7 network antenna 2.7 parallel 2.6 power cord 2.7 USB 2.6 control panel 3.1 buttons 3.
2 in the paper feed area Multi- Purpose T ray 7.6 optional Tray 2 7.4 , 7.5 Tray 1 7.4 tips for avoidin g 7.8 paper level ind icator 4.2 paper size, change i n the tray 3.4 parallel cable, connect 2.6 PostScript driver errors 7.13 install 2.8 preprinted paper, print 4.
Samsung Printer Software section.
1 S OFTWARE SECTION C ONTENTS Chapter 1: I NST ALLI NG P RINTER S OFTWARE IN W INDOWS Installing Printer Software ................... ........................ ........................ ....................... ......... ..... 4 Installing Softwar e for Local Pri nting .
2 Using an Existing Watermark ...... .............. ........................ ........................ ..................... 22 Creating a Watermark ...... .......... .............. ........................ ........................ ....................
3 Chapter 8: U SING Y OUR P RINTER WITH A M ACIN TOSH Installing Software for Macintosh ................... ............... ........................ ....................... ............ 35 Setting Up the Printer ........... .... ..... ................
Installing Printer Software in Windows 4 1 Installing Printer Software in Windows This c hapte r inclu des: • Installing Printer Software • Changing the Soft ware La ng uag e • Reinstalling Prin.
Installing Printer Software in Windows 5 N OTE : If your pri nter is not alr eady connected to the computer , the foll owin g window wi ll a ppear . • After connecting the printer , click Next . • If you don’t want to co n nect the p r inter at this time, click Next , and No on the f ollowi ng screen.
Installing Printer Software in Windows 6 3 Click Next . • If necessary , select a language from the drop-down list. • View User’s Guid e : Allo ws you to vi ew the User ’s Guide. If your comput er doesn’ t have Adobe Acrobat, clic k o n this op tio n a nd it wil l au to ma tica lly ins ta ll A do be Acrobat Reader for you.
Installing Printer Software in Windows 7 9 T o regist er yourself as a user of Samsung Printers in order to receive information from Samsung, select the checkbox and click Finish . Y o u a re now sent to the Samsung web site. Otherwise, just click Finish .
Installing Printer Software in Windows 8 5 The list of pr inter s a vai la b le on t h e netw o rk ap pe ars. Select the printer you wan t to install from the list and then click Next . • If you do not se e your print er on the li st, click Update to refresh the list, or select Add TCP/IP Port to add your printer to the n e tw ork.
Installing Printer Software in Windows 9 5 The list of pr inter s a vai la b le on t h e netw o rk ap pe ars. Select the printer you wan t to install from the list and then click Next . • If you do not se e your print er on the li st, click Update to refresh the list, or select Add TCP/IP Port to add your printer to the n e tw ork.
Installing Printer Software in Windows 10 Changing the Software Language After installation of the softw a re, you can change the display language. 1 Click the Windows Start menu. 2 Select Programs or All Programs and t hen your pri nter driver name .
Installing Printer Software in Windows 11 Removing Printer Software 1 Start Windows. 2 From the Star t menu select Programs or All Programs → your printer driver name → Mai ntena nce . 3 Select Remove and click Next . Y ou will see a component list so that you can remov e an y item indiv idually .
Basic Printing 12 2 Basic Printing This chapter explains the printing options and co mmon p rinting tasks in Windows. This c hapte r inclu des: • Printing a Docu m en t • Printer Se ttings - Lay o.
Basic Printing 13 Printer Settings Y ou can use th e printer p roperties wi ndow, which allows you to access all of t he printer options you need when using your printer . When the printer pr ope rties are d ispla y ed, you can review and change t he settings ne eded for your print job.
Basic Printing 14 Pape r Tab Use the following options to set the basic paper hand ling specif icat ions when you acc ess the pr inte r propert ies. See “Printing a Document ” on page 12 for more info rmation on accessing printer properties. Click the Paper tab to access various paper properties.
Basic Printing 15 Graphic s Tab Use the followin g Grap hic optio ns to adju st th e prin t qu alit y for you r s pecific pri ntin g n eed s. See “Pr inting a D ocum ent” on page 12 for m ore in form ation o n acc essing pr inte r pr ope rtie s. Clic k the Grap hics ta b to d ispla y th e pro pe rties show n be low .
Basic Printing 16 Extras Tab Y ou can select output optio ns for your document. See “Printing a Document” on page 12 for more informati on about accessing the printer pr o pe r ties. Click the Extras tab to access the following feature: Water mark Y ou can create a background text image to be printed on each page of your document.
Basic Printing 17 About Tab Use the About tab to display th e co py righ t no tice an d th e version number of the dri ver . If you have an Internet browser , you can connect to the Internet by clicking on the web si te icon. See “Printing a Document” on page 12 for more i nformation about accessing printer properties.
Adva nce d Prin ti ng 18 3 Advance d Prin ting This chapter expl ains pri nting opti ons and advanced printing tasks. N OTE : • Y o ur printer driver Properties window that a p pears in this User’s Guide may dif fer de pending on the printer in use.
Adva nce d Prin ti ng 19 Printing Posters This featur e allows you to print a single-page document onto 4, 9, or 16 sheets o f paper , for the purpo se of p astin g the sheet s togethe r to fo rm o n e po ste r - siz e document. 1 T o change the print setting s from your software applic ation, access printer properti es.
Adva nce d Prin ti ng 20 Printing on Both Sides of Paper N OTE : Some printers do not suppo rt this featur e. Y ou ca n prin t on bot h side s of a sheet of pape r .
Adva nce d Prin ti ng 21 Printing a Reduced or Enlarged Document Y ou can cha nge the si ze of a page’s content to appear larger or smaller o n th e pr inte d page. 1 T o change the print setting s from your software applic ation, access printer properti es.
Adva nce d Prin ti ng 22 Using Watermarks The W aterm ark option allows you to print text over an ex isting document. For example, you may want to have large gray lette rs rea ding “D RAFT” or “CONFI DENTIAL ” prin ted di agonall y across the fi rst page or a ll pages of a d ocument.
Adva nce d Prin ti ng 23 Editing a Watermark 1 T o change the print setting s from your software applic ation, access printer properti es. See “Print ing a Document” on pa ge 12. 2 Click the Extras tab an d c l ick th e Edit button in the Water mark section.
Adva nce d Prin ti ng 24 4 In t h e Edit O v erlay windo w, c lick Create O verlay . 5 In the Crea te Overlay win do w , type a n am e of up to eight characters in the File name box. Select the destination path, if necessary . (The de fault is C:Formover).
Adva nce d Prin ti ng 25 6 If necessary , click Con f ir m Page Overla y When Printing . If this box is checked, a message w i ndow appears each time y ou subm it a docum e nt for printing, asking you to confirm your wish to print an overlay on your document.
Using Windows PostScript Driver 26 4 Using Windows PostScript Driver If you want to use the PostScript dr iver provided wi th your system CD-ROM to p rint a docu me nt. PPDs, in combination with the P ostScript driver , access printer features and allow th e co m puter to communi cate w i th the printer .
Sha ring the P rinte r Lo cally 27 5 Sharing the Printer Locally Y ou can connect the printer directly to a selected computer , which i s ca lled “ host compu t er , ” o n th e n e twork. The follo wing procedure is for Windows XP . For other Windows OS, refer t o the correspo nding Windows User' s Guide or online help.
Using Smart Panel 28 6 Using Smart Panel Smart P anel is a progra m that monitors and informs you of the status of the printer , and allows you to customiz e the printe r’s settings. Smar t Panel is installed automatically when you install the printer sof tware.
Using Smart Panel 29 Using Printer Settings Utility Using the Print er Settings Ut ility , you can configure and check print settings. 1 Right-click the S m art Panel icon on the Wind ow s task b ar and select Printer Se tting . 2 Change th e settin gs.
Usin g Yo u r Pri n t er in Lin ux 30 7 Using Your Printer in Linux Y ou can use your print er in a Linux environment. This c hapte r inclu des: • System Requ irements • Installing t he Printer Dr.
Usin g Yo u r Pri n t er in Lin ux 31 Installing the Printer Driver 1 Make sure that you connect the print er to your computer . T urn both the computer and the printer on. 2 When the Administrator Login wi ndow appears, type in “ root ” in the Login fiel d and ente r the sy stem passwor d.
Usin g Yo u r Pri n t er in Lin ux 32 9 Click the Conne ction tab and ensure that the printer p ort is set properly . If it is not, change the de vi ce setting. 10 Y ou can use the Sett ings tab and t he Queue tab to view the printer’s current settings.
Usin g Yo u r Pri n t er in Lin ux 33 Uninstalling the Printer D river 1 From the Startup Menu ico n a t the bottom of the desktop, select Linu x P r inter and then Confi gur at i on To ol . Y ou can also access the Linux Printer Configuration window by typing i n “ linux-config ” from th e T erminal screen.
Usin g Yo u r Pri n t er in Lin ux 34 The Propertie s tab allows yo u to ch ang e the default printer settings. N OTE : R e gular users ar e able to ov e rride the sy s t em -wide default set tings defined by t he administrator .
Using Your Prin ter w it h a Macintosh 35 8 Using Your Printer with a Macin tosh Y our machine s upports Macintosh systems w ith a built-in USB interface or a 10/1 00 Ba se- TX network interface card. When you print a file from a Macintosh computer , you can use the PostScript dri ver by installing the PPD file.
Using Your Prin ter w it h a Macintosh 36 Setting Up the Printer Set up for your pr inter will be differ ent depending on which cable you use to co nnect the print er to your computer—the network cable or the USB cable . For a Network-connected Macintosh N OTE : Some printers do not suppo rt a ne tw ork interfa ce .
37 Printing N OTES : • The Macinto sh printer ’s properties window that appear s in this User ’s Guide may differ dep ending on the p rinter in use . Howeve r the com position of the pr inter properties wind ow is similar . • You can check your printer name in the supplied CD- ROM.
38 Printer Features Setting The Print e r Features tab provides opt ions for sel ecting the paper type and adjus ting pr int qual ity . Select Printer Featu res from the Presets drop-down li st to access the following features: Revers e Dupl ex Allows you to select general print order compare to duplex print order .
39 Duplex Printin g Y ou can print o n bo th sides of the p aper . Before printing in the duplex mode, deci de on which e dge you will be bindi ng your finishe d document.
40 S OFTWARE SECTION I NDEX A advanced printing, use 18 B booklet printing 19 D document, print Macintosh 37 Windows 12 double-sided printing 20 E Extras properties, set 16 F favorites settings, use 1.
41 Linux 31 Macintosh 35 Win dow s 4 reinstall Win dow s 10 system requirem ents Linux 30 Macintosh 35 uninstall Linux 33 Win dow s 11 status monitor, use 28 system requireme nts Linux 30 Macintosh 35.
R e v . 3 .0 0.
Ein wichtiger Punkt beim Kauf des Geräts Samsung ML 3560 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Samsung ML 3560 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Samsung ML 3560 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Samsung ML 3560 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Samsung ML 3560 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Samsung ML 3560 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Samsung ML 3560 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Samsung ML 3560. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Samsung ML 3560 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
