Benutzeranleitung / Produktwartung ORBIT-6 RP-206 des Produzenten Rokonet
Zur Seite of 37
Installer Manual 1 INSTALLER MANUAL VER. B.
Installer Manual 2 Customer Information 1. The ORBIT-6 (Model RP-206) complies with FCC Part 68 Rules. On the upper panel of this product is a label that contains, among other information, the FCC Registration Number and Ringer Equivalence Number (REN is 0.
Installer Manual 3 Copyright © 2001 by Rokonet Ltd., 14 Hachoma Street Rishon Letzion 75655 Israel All rights reserved. No part of this document may be reproduced in any form without prior written permission from the publisher.
Installer Manual 4 Summary of User’s Commands This page, called a Command Summary, is intended to give you brief summaries of common system operations. More detailed explanations and related information can be found within, by referring to the user manual.
Installer Manual 5 TABLE OF CONTENTS Introduction to the ORBIT-6 .................................................................. 6 Main Features: .................................................................................. 6 Installation ....
Installer Manual 6 INTRODUCTION TO THE ORBIT-6 The ORBIT-6 is intended to address the needs of many homes, offices, and small businesses. Its operation is designed around microprocessor and EEPROM (El.
Installer Manual 7 INSTALLATION Before You Begin Be sure the actual work is performed by experienced personnel, licensed to carry out security system installations and capable of implementing all appl.
Installer Manual 8 TECHNICAL DATA Main Panel Input power 16.5 V AC 25 VA via transformer Rechargeable standby battery 12 V 4 A-Hours Auxiliary Power 12 V DC 250 mA maximum Bell/LS Sounder output 12 V DC 750mA maximum Programmable output Open collector Active pull down 70mA maximum Cabinet Dimensions: 260X218X83 mm (10.
Installer Manual 9 INSTALLER PROGRAMMING The keypad The Orbit-6 can support up to 4 keypads, with a choice of 3 styles, 1 LCD type and two LED types from which virtually all features may be accessed. In addition to the functions it provides for the user, each of the keypads can be used by an installer to program the system parameters.
Installer Manual 10 Programming your Orbit-6 Programming Methods Local Requirements LED or LCD keypads The keypad must be wired to the Orbit- 6 panel. Power must be applied to the Orbit-6. Orbit Programmer Easy programming of the control panel parameters with menu driven LCD display.
Installer Manual 11 Viewing the Contents of a Location It’s often necessary to check the data stored in a memory location to be sure it’s correct. If improper data is found, it must be corrected in order to obtain the desired system response. The data in a location can either be a number (from 0-9) or a letter (from A-F).
Installer Manual 12 Locations Whose Contents Occupy More Than One Digit When a location contains more than one digit, they cannot be viewed simultaneously.
Installer Manual 13 Operation Action Comments 1 Enter the Installer Programming mode enter the factory default Installer Code ( 0-2-0- 6 ); followed by # a long beep will sound, confirming successful .
Installer Manual 14 GENERAL SYSTEM PARAMETERS: LOCATIONS 00–05 Location: 00 Default En able : Def: 00 PURPOSE: to enable or disable the option of resetting the system to the factory defaults. 00 Enable the option of resetting the system to the factory defaults.
Installer Manual 15 Location: 04 Callback UD Phone # Enables greater security for remote Upload/Download operation. This is a number to which the alarm company computer, equipped with the U/D software, will be connected.
Installer Manual 16 Location: 09 Installer Code II Default: 1206 Same as the Installer Code 1, but with a few limitations: It can't modify the "default code", observe and modify the first installer's codes, modify any MS phone number, nor observe & modify MS lock code.
Installer Manual 17 Locations: 14- 21 Zone 1-8 : (1 st Digit): Type Default: 1 st Digit Zone Type and Comments 0 Not Used All unused zones should be given this designation.
Installer Manual 18 Locations: 14-21 Zone 1-8: (2 nd Digit): Sound Default: 2 nd Digit Zone Sound and Comments 0 Silent a violation during the armed period will produce no sound the resulting alarm ca.
Installer Manual 19 Location: 18 Zone 5: (2 nd Digit): Sound Default: External Sounder (Pulses) For fire zone the recommended (default) zone sound is “External sounder pulsed” However it is possible to change the zone sound and type to any of the ones provided in the previous list.
Installer Manual 20 Digit Event and Result 00 (default) Not Active UO offers no response to any system activity 01 Arm Follow (Latch) U0 is activated when the system is armed. The activation occurs after the expiration of the exit/delay period. The U0 remains active (latched) while the system is armed.
Installer Manual 21 17 Special Emergency Keying Follow (Latched) UO is activated immediately when pressing the keypad’s [7] and [8] keys simultaneously for two seconds.
Installer Manual 22 24 Duress Code Follow (Latched) UO is activated when any duress code is entered. The UO deactivates either when arming the system or disarming the system due to an alarm that was activated from the emergecy keypad keys, 24-hour zone violation or tamper zone violation.
Installer Manual 23 Location: 2 6 Dialer Controls: (2 nd Digit): 2 nd Digit Attempts Answering Machine UL Installation Voice Module 0 3 No No No 1 8 No No No 2 3 Yes No No 3 (default) 8 Yes No No 4 3 .
Installer Manual 24 Understanding the Code Format To understand and modify the Code format according to a specific central station see the following • First digit: determine the number corresponding.
Installer Manual 25 Location: 28 CS Protocols: When selecting a contact ID & SIA format, all the reporting codes will be automatically applied to the locations of the reporting codes. To change a code, enter a new code (according to the type of event – see page 30 ) to the corresponding location.
Installer Manual 26 Comments on System Controls (Location 30: 2 nd Digit) Silent Panic Bell Squawk on Arming 3 Minute Bypass Enabled If “NO”, the panic alarm will be AUDIBLE at the External Sounder and visual on the keypad. If “YES”, the panic alarm will be INAUDIBLE at the External Sounder and invisable on the keypad.
Installer Manual 27 System Controls: 1 ST Digit System Controls: 2 nd Digit PERIODIC TEST TIME: LOCATION 31 If desired, the ORBIT-6 can send a daily test transmission to the Central Station to verify the operation of the unit’s Digital Communicator.
Installer Manual 28 Other Reporting Codes Location Description Digits Default Report Code 54 Daily test Report Code sent everyday at the time specified in Location 24 2 00 55 User 0 arm (the “Master.
Installer Manual 29 ORBIT-6 Installer Programming Worksheet Customer ________________________ Address _________________________ City ____________ State _____Zip ___ Customer Phone No: ( ) ____________.
Installer Manual 30 CONTACT ID & SIA REPORT CODES FOR ORBIT 6 Event Reporting Contact ID SIA Zones Alarms/Disarm Program Digit Code Program Digit Code Exit/Entry Alarm 01 134 01 BA Exit/Entry Rest.
Installer Manual 31 Event Reporting Contact ID SIA Zones Alarms/Disarm Program Digit Code Program Digit Code Low Temperature Alarm/Restore 34 159 34 DA Los of Air Flow 35 161 35 DB Special Special Eme.
Installer Manual 32 TI P RIN G TELEPHON E SE T TO TELEPHON E LINE TR1 ORBIT-6 Wiring Diagram FIGURE 1 A SET LINE PHO NE UR 1 P 1 J 2 J 1 DEFAUL T TYPICAL FIR E ZONE WIRING S (4 WIRE SMOKE DETECTIONS ).
Installer Manual 33 12VD C 750 m A MAX N/ C CONTACT S TO KEYPAD(S) TI P RIN G TELEPHON E SE T TO TELEPHON E LINE TR1 ORBIT-6 Wiring Diagram FIGURE 1 B S E T L IN E P H O N E UR 1 P 1 J 2 J 1 DEFAUL T .
Installer Manual 34 Zone Extension Power LED Arm LED Ready LED Fire LED Zone 1 Zone 2 Zone 3 Backlit LEDS Zone 4 Zone 5 Zone 6/Tmp Zone 7 Zone 8 AUX GND CLK DAT WHT RED BLK YEL GRN ( Keypad Buzzer ) P.
Installer Manual 35 Notes.
Installer Manual 36.
Installer Manual 37 ROKONET LIMITED WARRANTY Rokonet Electronics, Ltd. and its subsidiaries and affiliates ("Seller") warrants its products to be free from defects in materials and workmanship under normal use for 18 months from the date of production.
Ein wichtiger Punkt beim Kauf des Geräts Rokonet Rokonet ORBIT-6 RP-206 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Rokonet Rokonet ORBIT-6 RP-206 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Rokonet Rokonet ORBIT-6 RP-206 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Rokonet Rokonet ORBIT-6 RP-206 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Rokonet Rokonet ORBIT-6 RP-206 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Rokonet Rokonet ORBIT-6 RP-206 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Rokonet Rokonet ORBIT-6 RP-206 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Rokonet Rokonet ORBIT-6 RP-206. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Rokonet Rokonet ORBIT-6 RP-206 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
