Benutzeranleitung / Produktwartung FS35ETRSL des Produzenten Rinnai
Zur Seite of 28
FS35ETRBN/US FS35ETRSN/US FS35ETRBL/US FS35ETRSL/US Gas Radiant Sp ace Heater Owners Operation and Inst allation Manual Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. WHA T T O DO IF YOU SMELL GAS • Do not try to light any appliance.
2 LIMITED W ARRANTY RINNAI FIREPLACE HEA TER WHA T IS COVERED? This W arranty covers any defects in materials or workmanship, subject to the terms st ated below . This Warranty extends to the original purchaser and subsequent transferees, but only while the product remains at the site of the original installation.
3 W ARNING IMPROPER INST ALLA TION, ADJUSTMENT , AL TERA TION, SERVICE OR MAINTENANCE CAN CAUSE PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE. INST ALLA TION AND SER VICE MUST BE PERFORMED BY A QUALIFIED INST ALLER, SERVICE AGENCY OR THE GAS SUPPLIER.
4 Model: FS35ETRBN/US, FS35ETRSN/US (NG) United S tates FS35ETRBL/US, FS35ETRSL/US (Propane) United S tates Description: Freest anding radiant/convector , glass-fronted, ceramic log space heater with .
5 8 Read these rules and the instructions carefully . Check all local codes. Failure to follow these could cause a malfunction of the heater resulting in death, serious bodily injury and/or property damage. 9 This appliance is only for use with the type of gas indicated on the rating plate.
6 Diagram shows minimum clearances from combustible materials of the control system and any gas control which has been under water . 1 7 Adequate clearances for accessibility for purposes of servicing and proper operation should be provided. 1 8 Adequate clearances around air openings into the combustion chamber should be provided.
7 TECHNICAL SPECIFICA TIONS COMP ARTMENTS, BURNERS AND CIRCULA TING AIR P ASSAGEW A YS OF THE APPLIANCE ARE KEPT CLEAN. 35 The glass window shall be replaced as one piece as supplied by the manufacturer . See log and glass installation on page 15. 3 6 Do not substitute glass, glowing embers or logs.
8 A This appliance is equipped with an ignition device which automatically ignites the pilot. Do not try to light the pilot by hand B. BEFORE OPERA TING smell all around the appliance area for gas. Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor .
9 For your convenience the controls on your new Flame Fire are situated under the cover on the top right-hand side of the fire and are accessed by simply lifting the lid. All necessary adjustments to the operation of your fire can be made with these controls.
10 deactivate the LOCK press and hold the button for 3 seconds until the indicator goes off. During normal operation the LOCK may be activated and all controls, other than the OFF switch, will be locked.
11 proceed to TIMER 2 - which is programmed in the same way - or three times to return to the clock display . This must be done within 1 minute of setting the time to lock it into the memory . The digital display will show the current time. A small indicator on the digital display will flash to show that the display has returned to the clock.
12 NOTE: Some fluorescent lights may interfere with the transmission of remote control signals, in this case changing the position from which you are operating the remote control may help. Avoid getting the remote control wet, or dropping it. The remote control works within 15 feet and an angle of 40° to the receiver on the unit.
13 1. Flue connection and proper venting 2. W arm air distribution. 3. Adequate air supply . 4. The heater must not be installed where curtains or other combustible materials could come into contact with it. In some cases, curtains may need restraining.
14 • RUN GAS SUPPL Y For pipe sizing, refer to your local gas installation codes. • PURGE SUPPL Y OF AIR AND DEBRIS All foreign materials such as filings must be purged from the gas supply , as they may cause the gas valve to malfunction.
15 The logset is packed inside the unit and the packaging must be removed prior to installing the logset in its correct position. • Open both side panels. • Remove fasteners on both sides of the top glass retainer . • Lift retainer away from unit.
16 • TESTING PROCEDURE T urn gas supply on and plug the unit into the power supply . (Caution 1 15V) • TO CHECK BURNER PRESSURE • Refer to rating plate. • Remove the wiring cover panel. • Remove test point plug and attach manometer to test point.
17 IMPORT ANT MAINTENANCE INSTRUCTIONS ANNUAL INSPECTION The unit should be inspected at least once a year by a qualified service technician including inspection of the flue system. The appliance area must be kept clear and free from combustible materials, gasoline and other flammable vapors and liquids.
18 1 3 3 2 1 1 3 4 2 2 The heater should be serviced annually only by an authorised person. • GLASS REPLACEMENT AND CLEANING . (May be performed by the owner) It is best to handle the glass with clean gloves to avoid smearing the glass with finger prints which might show after replacement.
19 WIRING DIAGRAM PCB LA YOUT Caution: Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation.
20 NOTE: If you have any other faults or problems, please refer to your Installer or local qualified service agency TROUBLE SHOOTING WIRING DIAGRAM-LADDER SY M PT OM CA USE SOLUTION N o pow er pres en.
21 E r r or code P r obabl e cause C ommen ts 11 I g ni ti o n fai lure C h e ck gas i s t u rn ed o n . Serv i ce cal l i f r epeat ed 12 Fl am e f ail u r e C h e ck gas i s t u rn ed o n .
22 EXPLODED DIAGRAMS.
23.
24 SP ARE P ARTS LIST I T EM N O. Q T Y. PAR T N O . 1 1 7 9 9 2- 1 FL U E SPI GO T ASSY FS N AT U SA 2 1 7 0 7 4 H EAT EX C H AN GER FR ON T ASSY 3 + 3 H 3 1 7 0 7 5 H EAT EX C H AN GER R EAR ASSY 3 .
25 5 1 1 7 9 8 8 V R EAR PAN EL F S3 5 ET R VI PER U SA BL AC K 1 7 9 8 8S P R EAR PAN EL FS3 5E T R SP U SA SI L VER 52 1 7472 A IR GUI DE LOW E R FS 35E T R 5 3 1 7 0 6 2 H EAT SH I EL D LO W ER R H.
26 INST ALLA TION NOTES.
27 1 . W as a fireplace inspection carried out? (i.e. clearances, combustibles etc.) 2. W as a manufactured flue system installed? 3 . Has specified gas pressure been set? 4 . Are decorative logs located correctly on pins? 5. Have ember granules been placed and free of dust and powder? 6.
Part Number 7917 zx.
Ein wichtiger Punkt beim Kauf des Geräts Rinnai FS35ETRSL (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Rinnai FS35ETRSL noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Rinnai FS35ETRSL - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Rinnai FS35ETRSL reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Rinnai FS35ETRSL erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Rinnai FS35ETRSL besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Rinnai FS35ETRSL verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Rinnai FS35ETRSL. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Rinnai FS35ETRSL gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
