Benutzeranleitung / Produktwartung SP 204SFN des Produzenten Ricoh
Zur Seite of 256
Operating Instructions User Guide For safe and correct use, be sure to read "Safety Information" before using the machine..
.
TABLE OF CONTENTS How to Read This Manual .................................................................................................................................6 Introduction .................................................................
Specifying Paper Type and Paper Size Using Control Panel................................................................... 35 Specifying Paper Type and Paper Size Using Smart Organizing Monitor.............................................37 Placing Originals .
Scan to E-mail/FTP/Folder......................................................................................................................... 69 Basic Operation for Scan to USB .....................................................................
7. Configuring the Machine Using the Control Panel Basic Operation ............................................................................................................................................. 103 Copier Features Settings .............
Removing Printing Jams ............................................................................................................................. 153 Removing Scanning Jams ...........................................................................
How to Read This Manual Introduction This manual contains detailed instructions and notes on the operation and use of this machine. For your safety and benefit, read this manual carefully before using the machine. Keep this manual in a handy place for quick reference.
About IP Address In this manual, "IP address" covers both IPv4 and IPv6 environments. Read the instructions that are relevant to the environment you are using.
Model-Specific Information This section explains how you can identify the region your machine belongs to. There is a label on the rear of the machine, located in the position shown below. The label contains details that identify the region your machine belongs to.
Important Safety Instructions User Information on Electrical & Electronic Equipment Users in the countries where this symbol shown in this section has been specified in national law on collection and treatment of E-waste Our Products contain high quality components and are designed to facilitate recycling.
on 64g/m 2 paper, which contains less raw materials and represents a significant resource reduction. Duplex printing (if applicable) Duplex printing enables both sides of a sheet of paper to be used. This saves paper and reduces the size of printed documents so that fewer sheets are used.
Notes to Users of Facsimile Unit Declaration of Conformity Notice to Users in EEA Countries This product complies with the essential requirements and provisions of Directive 1999/5/EC of the European .
Important Safety Instructions Notes on Lamp(s) Inside This Machine Notes to Users in the State of California Perchlorate Material - special handling may apply.
ENERGY STAR Program ENERGY STAR ® Program Requirements for Imaging Equipment The ENERGY STAR ® Program Requirements for Imaging Equipment encourage energy conservation by promoting energy efficient computers and other office equipment. The program backs the development and dissemination of products that feature energy saving functions.
Energy Saver mode 2 Power Consumption *1 3.9 W or less Default Interval 1 minute Recovery Time *1 17 seconds or less *1 Recovery time and power consumption may differ depending on the conditions and environment of the machine. Recycled Paper We recommend you to use environmentally friendly recycled paper.
1. Guide to the Machine Guide to Components This section introduces the names of the various parts on the front and rear side of the machine and outlines their functions. Exterior • Type 1 models do not come with an Ethernet port and USB Flash Disk Port.
5. Bypass Tray This tray can hold one sheet of plain paper. 6. Tray 1 This tray can hold up to 150 sheets of plain paper. 7. USB Flash Disk Port Insert a USB flash disk to store scanned files using the Scan to USB function. 8. Power Switch Use this switch to turn the power on or off.
Interior CTT065 1 1. Print Cartridge A replacement consumable that is required to make prints on paper. It needs to be replaced after approximately every 1,500 or 2,600 pages printed. For details about replacing the cartridge, see page 145 "Replacing the Print Cartridge".
2. [Copy] Key Use this key to switch the machine to copier mode. 3. [Speed Dial] Key Use this key to send a fax using a registered speed dial number. 4. [ID Card Copy/On Hook Dial] Key When the machine is in copier mode, use this key to perform an ID copy or modify ID copy settings.
Initial Setup When you turn this machine on for the first time, you must set the following items. Select each setting using the [ ], [ ], or number keys, and then press the [OK] key.
What is Smart Organizing Monitor? Install this utility on your computer from the included CD-ROM before using it. Smart Organizing Monitor provides the following functions: • Displays the status of the machine Displays paper jam messages and other error messages.
Configuring Network Settings This section describes configuring the settings required to use the machine on a network. Configuring the IP Address Settings Using the Control Panel The procedure for configuring network settings differs depending on whether IP address information is assigned automatically by the network (DHCP), or manually.
Assigning the machine's IPv6 address manually • The IPv6 address assigned to the machine must not be used by any other device on the same network. • Make sure [DHCPv6] is set to [Disable] in [IPv6] in Web Image Monitor. For information about how to launch Web Image Monitor, see page 129 "Using Web Image Monitor".
• Install the driver after configuring the IP address. For details about installing the driver, see the Software Installation Guide. • For details about configuring the IPv4 address, see the Software Installation Guide.
1. Guide to the Machine 24.
2. Loading Paper Supported Paper Paper Size • A4 • 8 1 / 2 " × 11 " (Letter) • 8 1 / 2 " × 14 " (Legal) • B5 • 5 1 / 2 " × 8 1 / 2 " (Half Letter) • 7 1 / .
• Bypass Tray 1 sheets (70 g/m 2 , 19 lb.) 2. Loading Paper 26.
Non-Recommended Paper Types Do not use the following types of paper: • Ink-jet printer paper • GelJet special paper • Bent, folded, or creased paper • Curled or twisted paper • Wrinkled pape.
Print Area The diagram below shows the area of the paper that the machine can print on. From the printer driver CHZ904 2 3 3 1 4 4 1. Print area 2. Feed direction 3. Approx. 4.2 mm (0.2 inches) 4. Approx. 4.2 mm (0.2 inches) • The print area may vary depending on the paper size and printer driver settings.
Copier function CHZ904 2 3 3 1 4 4 1. Print area 2. Feed direction 3. Approx. 4 mm (0.2 inches) 4. Approx. 3 mm (0.1 inches) • The print area may vary depending on the paper size.
3. Approx. 4.2 mm (0.2 inches) 4. Approx. 4.2 mm (0.2 inches) • The print area may vary depending on the paper size. 2. Loading Paper 30.
Loading Paper Load a stack of paper for printing in the input tray. • When loading paper, be sure to configure the paper size and paper type for the bypass tray and Tray 1.
3. Pinch the end paper guide and slide it inward to match the standard size. CTT074 4. Fan the paper before loading it in the tray. 5. Load the new paper stack print side down. Make sure paper is not stacked higher than the upper limit marked inside the tray.
CTT094 Extending Tray 1 to load paper 1. Pull Tray 1 out slowly, and then remove it using both hands. 2. Release the extender locks on both sides of the tray, and then pull out the extender. CTT077 Make sure the extender's inner surface and the scale are aligned.
5. Attach the tray cover. CTT095 • Legal paper or custom-size paper longer than A4 must be loaded without attaching the tray cover. Loading Paper into Bypass Tray 1. Open the bypass tray. CTT063 2. Slide the side guides outward, load paper with the print side up, and then push in until it stops against the machine.
3. Adjust the side guides to the paper width. CTT033 To deliver the sheets face up, open the rear cover. CTT094 Specifying Paper Type and Paper Size Using Control Panel Specifying the paper type 1.
2. Press the [ ] or [ ] key to select [System Settings], and then press the [OK] key. To specify the type of paper in the bypass tray, select [Copier Features], and then press the [OK] key. 3. Press the [ ] or [ ] key to select [Tray 1 Ppr Settings], and then press the [OK] key.
Specifying a custom paper size 1. Press the [User Tools] key. CTT129 2. Press the [ ] or [ ] key to select [System Settings], and then press the [OK] key. To specify the size of paper in the bypass tray, select [Copier Features], and then press the [OK] key.
4. If the machine you are using is not selected, click [Select Device...], and then select the machine's model. 5. Click [OK]. 6. On the [Status] tab, click [Change...]. 7. Select the paper type and paper size, and then click [OK]. 8. Click [Close].
Placing Originals This section describes the types of originals you use set and how to place them. About Originals Recommended size of originals Exposure glass • Up to 216 mm (8.5 ") in width, up to 297 mm (11.7 ") in length ADF • Paper size: 105 to 216 mm (4.
Unscannable image area Even if you correctly place originals, margins of a few millimeters on all four sides of the original may not be scanned. Margins when using exposure glass CHZ916 Copier, Fax 1. Approx. 4.1 mm (0.2 inches) 2. Approx. 3 mm (0.1 inches) 3.
1. Approx. 4.1 mm (0.2 inches) 2. Approx. 3 mm (0.1 inches) 3. Approx. 4.3 mm (0.2 inches) Scanner (Scan to E-mail, Scan to FTP, Scan to Folder, Scan to USB) 1.
1. Open the input tray for the ADF. CTT035 2. Adjust the guides according to the size of the originals. CTT036 3. Place the aligned originals face up in the ADF.
3. Printing Documents Basic Operation Use the printer driver to print a document from your computer. 1. After creating a document, open the [Printing Preferences] dialog box in the document's native application. 2. Change any print settings if necessary.
3. When setting changes are completed, click [OK]. 4. Print the document using the print function in the document's native application. • If a paper jam occurs, printing stops halfway. Open the front cover, remove the print cartridge, and then remove the jammed paper.
Landscape CTT010 6. Press the [Start] key. • If the rear cover is open, the paper is delivered face up from the rear. Rearrange the printed sheets in the correct order. Canceling a Print Job You can cancel print jobs using either the machine's control panel or your computer, depending on the status of the job.
Canceling a print job while printing 1. Press the [Stop/Clear] key. CTT130 2. Press the [1] key. To cancel printing, press the [1] key (1: Yes). To continue printing, press the [2] key (2: No).
If a Paper Mismatch Occurs If the paper size or type does not match the print job's settings, the machine reports an error. There are two ways to resolve this error: Continue printing using mismatched paper Use the form-feed function to ignore the error and print using mismatched paper.
3. Printing Documents 48.
4. Copying Originals Copier Mode Screen Standby mode screen • First line: Displays the function and paper size specified on the machine. The following five functions are available: • Copier, ID Ca.
Basic Operation • The original in the ADF takes precedence over the original on the exposure glass if you place originals both in the ADF and on the exposure glass. • To print on paper fed from Tray 1, remove the paper loaded in the bypass tray. Otherwise, the paper in the bypass tray is fed first.
• If there is a paper jam in the ADF, open the ADF cover, and then remove the jammed paper. Specify the copy setting again from the page where the paper jammed. Canceling a Copy If copying is canceled while scanning an original placed on the exposure glass, copying is canceled immediately and there is no printout.
Making Enlarged or Reduced Copies There are two ways to set the scaling ratio: using a preset ratio or manually specifying a customized ratio. Preset ratio CES103 (mainly Europe and Asia) 50%, 71% A4 .
Specifying Reduce/Enlarge 1. Press the [Copy] key. CTT124 2. Press the [ ] or [ ] key in the standby mode screen to select [Reduce/Enlarge], and then press the [OK] key.
Combining Multiple Pages This section describes how to set the machine to combine multiple pages (2 or 4 pages) of an original onto a single page. • To use this function, the paper size used for printing copies must be set to A4 or Letter. 2 on 1 You can copy two pages of an original onto a single sheet of photocopied paper.
CES036 • Landscape: L to R CES037 • Landscape: T to B CES038 Specifying Combine for Copying 1. Press the [Copy] key. CTT124 2. Press the [ ] or [ ] key in the standby mode screen to select [Combine], and then press the [OK] key. 3. Press the [ ] or [ ] key to select [2 on 1] or [4 on 1], and then press the [OK] key.
6. Place the original on the exposure glass or in the ADF. 7. To make multiple copies, enter the number of copies using the number keys. 8. Press the [Start] key. CTT131 When you place the original on the exposure glass, perform the following steps to scan the subsequent pages of the original.
Copying Both Sides of an ID Card onto One Side of Paper This section describes how to copy the front and back sides of an ID card or other small documents onto either side of a sheet of paper. When copying onto A4 paper, you can copy documents that are smaller than A5.
2. Press the [ID Card Copy/On Hook Dial] key. CTT126 3. To make multiple copies, enter the number of copies using the number keys. 4. Place the original front side down with the top to the rear of the machine on the exposure glass. CTT169 The location to place the original depends on the paper size.
LT HL T LT HL T A6 A5 Half Letter A4 Letter CTT206 5. Press the [Start] key. CTT131 6. Within 30 seconds, place the original back side down with the top to the rear of the machine on the exposure glass, and then press the [Start] key. • In the ID card copy screen, you can press the [ ] or [ ] key to change the paper size.
Making 2-sided Copies • To use this function, the paper size used for printing copies must be set to A4 or Letter. • This function cannot be available with the bypass tray. You can select top-to-top or top-to-bottom binding, in either portrait or landscape orientation.
Specifying 2 Sided Copying 1. Press the [Copy] key. CTT124 2. Press the [ ] or [ ] key in the standby mode screen to select [2 Sided Copy], and then press the [OK] key. 3. Press the [ ] or [ ] key to select [Top to Top] or [Top to Bottom], and then press the [OK] key.
10. Take out all of the prints from the output tray and place them in Tray 1. To print on the reverse side of the prints, turn them over so that the blank side faces down and place them in Tray 1. Portrait CTT009 Landscape CTT010 11. Press the [Start] key.
Specifying the Scan Settings This section describes how to specify image density and scan quality for the current job. Adjusting Image Density There are five image density levels. The higher the density level, the darker the printout. 1. Press the [Copy] key.
Text/Photo Select this when the original contains both text and photographs or images. Specifying the Original Type 1. Press the [Copy] key. CTT124 2. Press the [ ] or [ ] key in the standby mode screen to select [Original Type], and then press the [OK] key.
5. Scanning Originals Scanner Mode Screen Standby mode screen • First line: Displays the current machine status. • Second line: Displays a message prompting you to enter the destination.
Registering the Scan Destination Registering the Scan Destination Use this procedure to register scan destinations from Smart Organizing Monitor. 1. On the [Start] menu, click [All Programs]. 2. Click [Smart Organizing Monitor for SP xxx Series]. 3. Click [Smart Organizing Monitor for SP xxx Series Status].
Enter the user account name for accessing the SMB server or shared computer. • [Password:] Enter the password for accessing the SMB server or shared computer. • [Directory:] Enter the path to the shared folder. When using Scan to FTP, specify [User Name:], [Password:], [Directory:], [E-mail Address:], and [E-mail Notification].
5. Click [OK]. 6. On the [User Tool] tab, click [Printer Configuration]. 7. On the [Scanner] tab, select the number you want to register, and then click [Modify...]. To delete a destination, select its registration number, and then click [Delete]. 8. Modify the destination, and then click [OK].
Basic Operation Scanning using the control panel allows you to send scanned files via e-mail (Scan to E-mail), to an FTP server (Scan to FTP), to the shared folder of a computer on a network (Scan to Folder), or to a USB flash disk (Scan to USB).
• If you are using Scan to Folder, create the destination folder on the computer's hard drive and make it a shared folder. For details, see your operating system's documentation. • To cancel scanning, press the [Scanner] key, and then press the [Stop/Clear] key.
Specifying the Scan Settings Specifying the Scanning Size According to the Size of the Original 1. Press the [Scanner] key. CTT128 If you are using Scan to USB, proceed to Step 4. 2. Using the number keys, enter the number of a registered scan destination.
If you are using Scan to USB, proceed to Step 4. 2. Using the number keys, enter the number of a registered scan destination. For details, see page 66 "Registering the Scan Destination". 3. Press the [OK] key. 4. Press the [ ] or [ ] key to select [Density], and then press the [OK] key.
Scanning from a Computer Scanning from a computer (TWAIN scanning and WIA scanning) allows you to operate the machine from your computer and scan originals into your computer directly. CTT174 1. Your Computer (TWAIN driver already installed) Instruct the machine to start scanning the original that is set on the machine.
Settings you can configure in the TWAIN dialog box CTT177 1 2 3 4 6 7 5 8 1. Select Mode Up to ten scan settings can be saved. The default value is applied when [Default] is selected. 2. Scan Mode: Select from [Full Color], [Grayscale], [Photo], [Text], or [Text/Photo].
7. Original Scan Method Specify the method to scan originals. If [ADF] is selected in [Original Scan Method], specify the orientation of the original. 8.
5. Scanning Originals 76.
6. Sending and Receiving a Fax Fax Mode Screen Standby mode screen • First line Displays the current machine status, month, and date. • Second line Displays the current resolution settings and time.
Setting the Date and Time 1. Press the [User Tools] key. 2. Press the [ ] or [ ] key to select [System Settings], and then press the [OK] key. 3. Press the [ ] or [ ] key to select [Set Date/Time], and then press the [OK] key. 4. Press the [ ] or [ ] key to select [Set Date], and then press the [OK] key.
Entering Characters To enter characters, use keys as follows: To enter a digit Press a number key. To delete a character Press the [ ] key for one second. To enter a fax number • To enter a number Use the number keys. • To enter characters other than digits " ": Press the [ ] key.
Registering Fax Destinations This section describes how to register fax destinations in the Address Book using the control panel. The Address Book can also be edited using Smart Organizing Monitor. For details, see the Smart Organizing Monitor Help. • The Address Book data may become damaged or lost unexpectedly.
Modifying or Deleting Fax Destinations 1. Press the [User Tools] key. CTT129 2. Press the [ ] or [ ] key to select [Address Book], and then press the [OK] key. 3. Press the [ ] or [ ] key to select [Fax Speed Dial Dest.], and then press the [OK] key. 4.
10. To delete a fax destination, select the destination in [Speed Dial Destination List:], and then click [Delete]. 11. Click [Apply] located in the lower part of the window.
Sending a Fax • It is recommended that you call the receiver to inquire if they received the fax you send important documents. A fax number can contain 0 to 9, pause, " ", and " ". If necessary, insert a pause in the fax number. The machine pauses briefly before it dials the digits following the pause.
1. Press the [User Tools] key. CTT129 2. Press the [ ] or [ ] key to select [Fax Features], and then press the [OK] key. 3. Press the [ ] or [ ] key to select [TX Settings], and then press the [OK] key. 4. Press the [ ] or [ ] key to select [Immediate TX], and then press the [OK] key.
4. Press the [Start] key. CTT131 Depending on the machine's settings, you may be prompted to enter the fax number again if you manually entered the destination fax number.
1. Press the [Stop/Clear] key. CTT130 2. Press the [1] key. To cancel sending a fax, press the [1] key (1: Yes). To continue sending a fax, press the [2] key (2: No). • If you cancel sending a fax while broadcasting, only the fax to the current destination is canceled.
Specifying the destination using Speed Dial 1. Press the [Facsimile] key. CTT125 2. Place the original on the exposure glass or in the ADF. 3. Press the [Speed Dial] key. CTT127 4. Enter the Speed Dial number using the number keys, and then press the [OK] key.
6. If you have more originals to scan, press the [1] key within 60 seconds, place the next original on the exposure glass, and then press the [OK] key. Repeat this step until all originals are scanned. 7. When all originals have been scanned, press the [2] key to start sending the fax.
1. Press the [Facsimile] key. CTT125 2. Place the original on the exposure glass or in the ADF. 3. Add a destination by using one of the following methods: To add a Speed Dial destination 1. Press the [Speed Dial] key. CTT127 2. Select a destination using the number keys, and then press the [OK] key.
Sending a fax using On Hook Dial The On Hook Dial function allows you to check the destination's status while listening to the tone from the internal speaker. This function is useful when you want to ensure that the fax will be received. • To send faxes using the exposure glass, be sure to first remove any originals loaded in the ADF.
CTT127 2. Select a destination using the number keys, and then press the [OK] key. To add a manually-specified destination 1. Enter the destination fax number using the number keys. 5. If you hear a high pitched tone, press the [Start] key. CTT131 6. If the original is placed on the exposure glass, press the [1] key (1: TX).
5. Press the [Start] key. CTT131 6. If the original is placed on the exposure glass, press the [1] key (1: TX). 7. Replace the handset. Specifying the Scan Settings Adjusting image density There are five image density levels. The darker the density level, the darker the printout.
Specifying the resolution Standard Select this when the original is a printed or typewritten document with normal-sized characters. Detail Select this when the original is a document with small print. Photo Select this when the original contains images such as photographs or shaded drawings.
Using the Fax Function from a Computer (PC FAX) This section describes how to use the fax function of the machine from a computer. You can send a document directly from a computer through this machine to another fax machine, without printing the document.
• A fax number can contain 0 to 9, "P" (pause), "T" (tone), " ", and " ". • To use tone services on a pulse-dialing line, insert "T" in a fax number. "T" switches the dialing mode from pulse to tone temporarily.
Configuring the PC FAX Address Book This section describes the PC FAX address book. Configure the PC FAX address book on the computer. The PC FAX address book allows you to specify PC FAX destinations quickly and easily. The PC FAX address book can contain up to 100 entries, including individual destinations and groups of destinations.
4. Enter the group name, and then click [OK]. Select the destination you want to include in the group from the [Address List:] area, and then click [Add to Group]. To delete a destination from a group, select the destination you want to delete from [Group Members List:], and then click [Delete Member].
Receiving a Fax • When receiving an important fax, we recommend you check the contents of the received fax with the sender. • The maximum number of fax pages that can be received and stored in the machine’s memory is 100 pages (50 jobs). • An external telephone is required to use this machine as a telephone.
1. Press the [User Tools] key. CTT129 2. Press the [ ] or [ ] keys to select [Fax Features], and then press the [OK] key. 3. Press the [ ] or [ ] keys to select [RX Settings], and then press the [OK] key. 4. Press the [ ] or [ ] keys to select [Switch RX Mode], and then press the [OK] key.
Receiving a fax in Auto mode When the reception mode is set to Auto mode, the machine automatically answers all incoming calls in fax reception mode. • You can specify the number of times the machine rings before answering a call in the [Number of Rings] setting under [Fax Features].
Lists/Reports Related to Fax The lists and reports related to the fax function are as follow: • Fax Journal Prints a fax transmission and reception journal for the last 100 jobs. • TX Status Report Prints out the latest Transmission result. • TX Standby File List Prints a list of unsent fax jobs remaining in the machine's memory.
6. Sending and Receiving a Fax 102.
7. Configuring the Machine Using the Control Panel Basic Operation • Type 1 models do not have [Scanner Features] and [Network Settings]. • Type 3 models do not have [Fax Features] and [Address Book]. • With certain models, some settings do not appear.
Copier Features Settings Sort Configures the machine to sort the output pages into sets when making multiple copies of a multi- page document (P1, P2, P1, P2...). Default: [ Off ] • On • Off Original Type Specifies the original type to optimize the copy quality.
50%, 71% A4 A5, 82% B5 JIS A5, 93%, 122% A5 B5 JIS, 141% A5 A4, 200%, Zoom: 25-400% (mainly North America) 50%, 65% LT HLT, 78% LG LT, 93%, 129% HLT LT, 155% HLT LG, 200%, Zoom: 25-400% Combine Select this to photocopy two or four pages of an original onto a single sheet of paper.
• Off • On Bypass Ppr Settings Paper Size Specifies the paper size. Default: (mainly Europe and Asia) [ A4 ] (mainly North America) [ LT (8 1 / 2 × 11) ] • A4, B5 JIS, A5, B6 JIS, A6, LG (8 1 /.
Fax Features Settings TX Settings Immediate TX Sets the machine to send a fax immediately when the original is scanned. Default: [ Off ] • Off Select this when using Memory Transmission. • On Select this when using Immediate Transmission. • Next Fax Only Select this when using Immediate Transmission for the next transmission only.
Pause Time Specifies the length of pause time when a pause is inserted between the digits of a fax number. Default: 3 seconds • 1 to 15 seconds, in 1 second increments Auto Redial Sets the machine to redial the fax destination automatically when the line is busy or a transmission error occurs.
Number of Rings Specifies how many times the external telephone or handset must rings before the machine starts to receive a fax when [Switch RX Mode] is set to [Auto]. Default: 3 times • 3 to 5 times, in increments of 1 If you have set [Country Code] to [Japan], you can specify it from 1 to 5 times.
The default depends on the [Country Code] setting. Transmission Speed Specifies the transmission speed for the fax modem. Default: [ 33.6 Kbps ] • 33.6 Kbps • 14.4 Kbps • 9.6 Kbps • 7.2 Kbps • 4.8 Kbps • 2.4 Kbps Reception Speed Specifies the reception speed for the fax modem.
• PSTN • PBX PBX Access Number Specifies the dial number to access the external line when the machine is connected to a PBX. Make sure that this setting matches your PBX settings. Otherwise, you may not be able to send faxes to external destinations.
PC FAX Error Report Sets the machine to print PC FAX error reports automatically. Default: [ Auto Print ] • Auto Print • Do not Auto Print 7. Configuring the Machine Using the Control Panel 112.
Scanner Features Settings Scanning Mode Select a scan type for the original. This setting is only applied to Scan to USB. Default: [ Color : Text/Photo ] • B&W : Text • B&W : Text/Photo • B&W : Photo • Gray Scale • Color : Text/Photo Resolution Specifies the resolution for scanning the original.
File Format Setting File format for B&W and Grayscale/ Color. This setting is only applied to Scan to USB. • B&W Default: [ Multi-page: TIFF ] • Single Page: TIFF • Single Page: PDF • .
• On (per size) • On (per page) • Off Delete Scanner File Deletes unsent scanner jobs remaining in the machine's memory. • Delete File • Delete All Files Scanner Features Settings 115.
Address Book Settings Fax Speed Dial Dest. Fax numbers and names can be registered in the speed dial list. Up to 100 entries can be registered. For details, see page 80 "Registering Fax Destinations".
System Settings Tray 1 Ppr Settings Paper Size Specifies the paper size. Default: (mainly Europe and Asia) [ A4 ] (mainly North America) [ LT (8 1 / 2 × 11) ] • A4, B5 JIS, A5, B6 JIS, A6, LG (8 1 .
Default: [ Middle ] Print Job End Tone Specifies the volume of the beep sound when a print job is complete. Default: [ Off ] Print Job Error Tone Specifies the volume of the beep sound when a print job error occurs. Default: [ Middle ] Scan Job End Tone Specifies the volume of the beep sound when a scan job is complete.
Set Time Sets the time of the machine’s internal clock. • Time format: 12-hour Format, 24-hour Format • AM/PM stamp: AM, PM (for 12-hour Format) • Hour: 0 to 23 (for 24-hour Format), or 1 to 12 (for 12-hour Format) • Minute: 0 to 59 Program Fax Info.
Mode 1, but it takes longer to recover from Energy Saver Mode 2 than from Energy Saver Mode 1. • Europe Default: [ 1 minute ] The time can be set from 1 to 30 minutes.
• • • (Needs replacing) If [Toner End Option] is set to [Continue Printing], "**" is displayed instead of the indicator above. Toner levels are always displayed for Type 3 models. Low Humidity Mode When the machine is used in a low humidity environment, black stripes with a few millimeters width may appear.
• (Darkest) Toner End Option This setting is used to monitor the toner level. Default: [ Stop Printing ] • Stop Printing Monitoring the toner level is enabled. The remaining toner level can be checked in the control panel and on the Smart Organizing Monitor.
Printing Lists/Reports Printing the Configuration Page 1. Press the [User Tools] key. CTT129 2. Press the [ ] or [ ] key to select [Print List/Report], and then press the [OK] key. 3. Press the [ ] or [ ] key to select types of report, and then press the [OK] key.
Fax Speed Dial List Prints a list of Speed Dial entries. Scanner Dest. List Prints a list of scan destinations. Scanner Journal Prints a scanner journal for the last 100 Scan to E-mail, Scan to FTP, and Scan to Folder transmissions. Network Setting List Prints the MAC address and IP address.
Printer Features Settings I/O Timeout Timeout: USB Specifies how many seconds the machine waits for print data if the data is interrupted while being sent from the computer via USB. If the machine does not receive any data within the specified time, the machine only prints the data it has received.
Network Settings Machine IPv4 Address • DHCP Activated Sets the machine to receive its IPv4 address, subnet mask, and default gateway address automatically from a DHCP server. When DHCP is used, you cannot specify the IPv4 address, subnet mask, or default gateway address manually.
Displays the IPv6 stateful address. • Manual Config. Add. Specifies the machine's IPv6 address when DHCP is not used. • IPv6 Gateway Address Specifies the IPv6 address of the default gateway.
7. Configuring the Machine Using the Control Panel 128.
8. Configuring the Machine Using Utilities Using Web Image Monitor • Some items can also be configured using the control panel. Available operations The following operations can be performed remotel.
1 3 2 CTT135 1. Menu area If you select a menu item, its content will be shown. 2. Header area The dialog box for switching to the user mode and administrator mode appears, and each mode's menu will be displayed. Click [Refresh] button at the upper right in the work area to update the machine information.
1. Interface Settings The interface setting appears. 2. IPv4 The IPv4 configuration appears. 3. IPv6 The IPv6 configuration appears. 4. Machine Information The machine information appears. Administrator Mode In the administrator mode, you can configure various machine settings.
2. IPv4 You can change the IPv4. 3. IPv6 You can change the IPv6. 4. SNMP You can change the SNMP. 5. Administrator Settings You can change the administrator password. 6. Restore Defaults You can reset the administrator password and other network settings.
Checking the System Information On the top page, you can check the current system information such as the device information, paper tray status, toner status, and total counter. Item Description Status Displays the icon indicating the device status. Toner Displays the remaining toner level.
Item Description I/O timeout (Network) Select whether or not to apply a timeout limit if the machine takes longer than a specified time to process a job. Ethernet Speed Ethernet communication speed. For normal use, select Auto Select. This allows the device to select the optimum speed.
Item Description Domain Name Specify whether to use the domain name obtained from the DHCP server, or the domain name set for the device. • "Auto-Obtain (DHCP)" selected When using DHCP, the domain name obtained from the DHCP server is used.
Configuring the IPv6 settings Click [IPv6] to display the page for configuring the IPv6 settings. IPv6 Item Description IPv6 Select whether IPv6 is active or inactive. Ethernet Item Description Host Name Enter the host name you want to set for the network interface board, using up to 63 characters.
Item Description DHCPv6 Select [Enable] to use the DHCPv6 server to automatically configure the network settings. Select [Disable] to manually configure the network settings. DDNS Select whether DDNS (Dynamic DNS) name resolution for the network interface board is active or inactive.
Configuring the SNMP Settings Click [SNMP] to display the page for configuring the SNMP settings. SNMP Item Description SNMP Select whether SNMP is active or inactive for the interface board(s). SNMPv1,v2 Setting Item Description SNMPv1 Trap Communication Select whether to send SNMPv1 trap.
Item Description Access Type In the list, select the access rights to the community. • Not Accessible No access permitted. • read-only You can read the information, but not edit it. • read-write You can read and edit the information. • trap Notifies the manager with information about errors.
Resetting the Machine’s Settings Click [Restore Defaults] to reset the network settings and administrator password. Checking the Machine Information Click [Machine Information] to display machine information. Machine Information Item Description Firmware Version Displays the version of firmware installed on the machine.
Using Smart Organizing Monitor • To use Smart Organizing Monitor, install the printer driver. Checking the Status Information CTT014 1 2 3 4 1. Image area Displays the status of this machine with an icon. 2. Status area • Paper Size Displays the paper size configured on the machine.
3. Select Device area Displays the name of the selected model. 4. Message area Displays the status of this machine with a message. For details about error messages, see page 175 "Error and Status Messages Appear on the Smart Organizing Monitor".
Scanner tab • You can edit the server's properties. • You can register, edit, and delete scan destinations. Printing the Configuration Page • When printing the test page, set the paper size to A4 or Letter. When printing other reports, set the paper size to A4, Letter, or Legal.
2. Click [Smart Organizing Monitor for SP xxx Series]. 3. Click [Smart Organizing Monitor for SP xxx Series Status]. 4. If the machine you are using is not selected, click [Select Device...], and then select the machine's model. 5. Click [OK]. 6.
9. Maintaining the Machine Replacing the Print Cartridge • If "Out of Toner" / "Print Cartridge" is displayed in the control panel, replace the print cartridge by following the procedure described below. However, this message will not be displayed if [Toner End Option] has been set to [Continue Printing].
5. Slide the print cartridge in horizontally, and then slowly push it in all the way. Finally, push the cartridge down until it clicks into place. CTT048 6.
Cautions When Cleaning Clean the machine periodically to maintain high print quality. Dry wipe the exterior with a soft cloth. If dry wiping is not sufficient, wipe with a soft, damp cloth that has been wrung out thoroughly.
Cleaning the Inside of the Machine 1. Open the front cover, and then carefully lower it. 2. Carefully pull out the print cartridge horizontally, holding its center. CTT045 3. Use a cloth to wipe the inside of the machine toward and away from yourself.
Cleaning the Exposure Glass 1. Lift the exposure glass cover. Be careful not to hold the input tray when lifting the exposure glass cover, for the tray might be damaged. 2. Clean the parts indicated with arrows with a soft damp cloth and then wipe the same parts with a dry cloth to remove any remaining moisture.
Cleaning the Auto Document Feeder 1. Lift the ADF. Be careful not to hold the input tray when lifting the ADF, for the tray might be damaged. 2. Clean the parts indicated with arrows with a soft damp cloth and then wipe the same parts with a dry cloth to remove any remaining moisture.
10. Troubleshooting Common Problems This section describes how to troubleshoot common problems that may occur while operating the machine. Problem Possible cause Solution The machine does not turn on. The power cord is not connected properly. • Make sure that the power plug is firmly inserted into the wall outlet.
Paper Feed Problems If the machine is operating but paper will not feed or paper jams occur frequently, check the condition of the machine and paper. Problem Solution Paper does not feed smoothly. • Use supported types of paper. See page 25 "Supported Paper".
Problem Solution Paper gets wrinkles. • Paper is damp. Use paper that has been stored properly. • Paper is too thin. See page 25 "Supported Paper". • If there are gaps between the paper and the paper guides, adjust the paper guides to remove the gaps.
Removing Jammed Paper from Tray 1 1. Pull Tray 1 halfway out, and check for jammed paper. If there is jammed paper, remove it carefully. CTT030 2. Carefully slide Tray 1 back in until it stops. 3. Open the front cover, and then carefully lower it. CTT054 4.
5. Lifting the guide plate, remove the jammed paper carefully. CTT046 6. Slide the print cartridge in horizontally, and then slowly push it in all the way. Finally, push the cartridge down until it clicks into place. CTT048 7. Carefully push up the front cover until it closes.
Removing Jammed Paper from the Bypass Tray • Since the temperature around the guide is high, wait for it to cool before checking for jammed paper. 1. If paper is jammed in the bypass tray input area, remove the jammed paper carefully. CTT034 2. Close the bypass tray.
2. Open the fusing cover. CTT079 3. Push the levers on the sides down with your thumbs. CTT080 4. Remove the jammed paper carefully. CTT066 5. Push the levers on the sides up with your thumbs.
7. Close the rear cover. CTT044 Removing Scanning Jams 1. Open the ADF cover. CTT038 2. Gently pull the jammed original to remove it. Be careful not to pull the original too hard, as it may tear.
3. Close the ADF cover. CTT039 4. Lift the ADF, and if there is original remaining in the ADF, gently pull the jammed original to remove it. Be careful not to hold the input tray when lifting the ADF, for the tray might be damaged. CTT027 5. Close the ADF.
Print Quality Problems Checking the Condition of the Machine If there is a problem with the quality of printing, first check the condition of the machine. Possible Cause Solution There is a problem with the machine's location. Make sure that the machine is on a level surface.
Printer Problems Problem Solution An error occurs. If an error occurs when printing, change the computer or printer driver settings. • Check the printer icon name does not exceed 32 alphanumeric characters. If it does, shorten it. • Check whether other applications are operating.
Print Positions Do Not Match Display Positions If the position of items on the printed page differs from the position displayed on the computer screen, the cause may be one of the following. Possible Cause Solution Page layout settings are not configured properly.
Copier Problems Problem Solution Photocopied paper is blank. The original was placed with the front and back reversed. See page 39 "Placing Originals". Copied pages are too dark or too light. Adjust the image density. Copied pages do not look the same as the originals.
Scanner Problems Problem Solution The scanned image is dirty. • The scanning part is dirty. • Before placing originals on the exposure glass, make sure that toner or correction fluid is dry. The scanned image is distorted or out of position. The original was moved during scanning.
Fax Problems When an error code appears on the fax journal or TX status report The table below describes the meaning of error codes that appear under "Status" on the fax journal or TX status report, and what to do when a particular error code appears.
Fax Journal Error Code Cause Solution 0001 The recipient’s fax machine does not support G3 standard. Select a transmission speed supported by the recipient fax machine, and resend the fax. 0071 Memory is full. Print, send, or delete the jobs stored in the memory.
Problem Solution Cannot print received faxes. • Tray 1 is empty. Load paper in Tray 1. See page 31 "Loading Paper". • Tray 1 does not contain paper of the right size. Load paper of the right size in Tray 1. Faxes you sent appear spotty or dirty when received.
Error and Status Indicate on the Control Panel Messages on the Screen • If the "Service Call: SCXXX" appears, contact your sales or service representative. • Depending on the model you are using, some error messages may not appear. Message Causes Solutions Tray 1 Out of Paper Tray 1 has run out of paper.
Message Causes Solutions Cannot Print Report Change Paper Size An appropriate size paper for printing Report is not loaded. Load A4, Letter or Legal size paper in Tray 1. Not Set Print Cartridge The print cartridge has not been installed. Reinstall the print cartridge.
Message Causes Solutions TX Comm. Error A transmission error occurred, and the fax could not be transmitted correctly. • If the [Auto Redial] setting is enabled, the machine will redial the number and try again. If all attempts fail, or if the machine is in Immediate Transmission mode, the fax will not be transmitted.
Message Causes Solutions Memory Data Lost Data in the memory was deleted due to a memory fault. The machine prints Power Failure Report and recovers from the error automatically.
Message Causes Solutions Cannot Obtain IP #### Server The machine cannot obtain an IP address from the FTP, SMTP, POP3, or SNTP server. If the problem involves the FTP server, check the [Edit Network Scan Destination] setting in Smart Organizing Monitor.
Message Causes Solutions File Over The assigned file names range from SIG000101 to SIG999901. If the file name assignment passes SIG999901, the naming starts over from SIG000101. If the name of the new is the same as an existing file for the same destination, the new file cannot be stored.
Message Causes Solutions No Destination Fax • No destination is registered in the selected Speed Dial. • You have attempted to redial, but there is no any redial data (history). Scanner The selected destination is not registered to a scan destination list.
Error and Status Messages Appear on the Smart Organizing Monitor Message Causes Solutions Printer Power Off (Communication Error) • The power cable of the machine is not plugged in. • The power of the machine is not turned ON. • The USB cable or Ethernet cable is not connected.
Messages of the Print Cartridge Message Causes Solutions Toner Almost Empty The print cartridge is almost empty. Prepare a new print cartridge. Out of Toner The machine has run out of the toner. Replace the print cartridge. See page 145 "Replacing the Print Cartridge".
Error and Status Messages Appear in the PC FAX Window Message Causes Solutions PC FAX has already been launched. Cannot launch it again. The [PC FAX] dialog box is already open. Quit PC FAX once, and then start it up again. Reached maximum number of destinations.
10. Troubleshooting 178.
11. Appendix Notes About the Toner • Proper operation cannot be guaranteed if any third-party toner is used. • Depending on printing conditions, there are cases where the printer cannot print the number of sheets indicated in the specifications.
Moving and Transporting the Machine This section provides cautions that you must follow when moving the machine both short and long distances. Repack the machine in its original packing materials when moving it over a long distance. • Be sure to disconnect all cables from the machine before transporting it.
Consumables Print Cartridge Print cartridge Average printable number of pages per cartridge *1 Black 1,500 pages, 2,600 pages *1 The printable number of pages is based on pages that are compliant with ISO/IEC 19752 with the image density set as the factory default.
Specifications of the Machine This section lists the machine's specifications. General Function Specifications Configuration Desktop Print process Laser electrostatic transfer Maximum paper size for scanning using the exposure glass 216 mm × 297 mm (8.
150 sheets (70 g/m 2 , 19 lb.) • Bypass Tray 1 sheet (70 g/m 2 , 19 lb.) Maximum loading height 15.5 mm (0.6 inches) Paper output capacity • Output Tray 50 sheets (70 g/m 2 , 19 lb.) • Rear 1 sheet (70 g/m 2 , 19 lb.) ADF capacity 15 sheets (80 g/m 2 , 21.
Printer Function Specifications Printing speed (mainly Europe and Asia) 22 pages per minute (A4) (mainly North America) 23 pages per minute (Letter) Resolution 600 × 600 dpi (maximum: 1200 × 600 dpi.
50%, 71%, 82%, 93%, 122%, 141%, 200% (mainly North America) 50%, 65%, 78%, 93%, 129%, 155%, 200% • Zoom ratio: 25% to 400% Copy quantity 99 Scanner Function Specifications Maximum scanning area (horizontal × vertical) • Exposure glass 216 × 297 mm (8.
Fax Function Specifications Access line • Public switched telephone networks (PSTN) • Private branch exchange (PBX) Transmission mode ITU-T Group 3 (G3) Scan line density 8 dots per mm × 3.85 line per mm (200 × 100 dpi) 8 dots per mm × 7.7 line per mm (200 × 200 dpi) Transmission time 3 seconds (8 dots per mm × 3.
Trademarks Apple, AppleTalk, Bonjour, ColorSync, Leopard, Macintosh, Mac OS, Power Mac, Safari and TrueType are trademarks of Apple Inc., registered in the United States and other countries. Firefox ® is a registered trademark of the Mozilla Foundation.
Microsoft ® Windows Server ® 2003 Enterprise Edition Microsoft ® Windows Server ® 2003 Web Edition Microsoft ® Windows Server ® 2003 Datacenter Edition • The product names of Windows Server 20.
INDEX 2 Sided copy ......................................................... 60 A Address book ...................................................... 116 Address book (PC FAX) ........................................ 96 ADF (Auto Document Feeder) ....
Paper jam ........................................... 153, 156, 158 Paper mismatch ..................................................... 47 Pause/Redial key .................................................. 66 PC FAX .................................
MEMO 191.
MEMO 192 EN GB EN US EN AU M135-8632.
.
EN GB EN US EN A U M135-8632 © 2013.
.
.
.
.
.
.
.
.
.
Item Beschrijving Actie Geef op hoe de IP-pakketten worden verwerkt: • [Toestaan]: IP-pakketten worden verzonden en ontvangen zonder toepassing van IPsec. • [Niet toestaan]: IP-pakketten worden verworpen. • [Beveiliging vereisen]: IPsec wordt toegepast op IP-pakketten die worden verzonden en ontvangen.
.
.
De beheerderinstellingen configureren Klik op [Beheerdertoepassingen] om de pagina voor configuratie van de beheerdersinstellingen te configureren. Deze pagina bevat de volgende tabbladen: [Beheerder], [Instellingen resetten], [Instellingen back- uppen], [Instellingen herstellen], [Datum/tijd instellen] en [Energiespaarstand].
Item Beschrijving Scanbestemming wissen Selecteer deze optie om de scanbestemmingen te wissen. Adresboek wissen Selecteer deze optie om de faxbestemmingen te wissen. IPsec-instellingen resetten Selecteer deze optie om IPsec-instellingen te wissen. • [IPsec-instellingen resetten] wordt alleen weergegeven als het beheerderswachtwoord is opgegeven.
Item Beschrijving Back-up van menu- instellingen Hiermee worden alle instellingen in een back-upbestand opgeslagen behalve de volgende: • Netwerkinstellingen • Scanbestemmingen • Instellingen vo.
.
.
.
9. Het apparaat onderhouden De printcartridge vervangen • Bewaar printcartridges altijd op een koele donkere plaats. • Het daadwerkelijke aantal kopieën die u kunt afdrukken, hangt af van het vol.
• Raak de ID-chip aan de zijkant van de printcartridge (zoals aangegeven op de afbeelding hieronder) niet aan. CVW050 • Als de toner opraakt, kunt u pas weer afdrukken als de nieuwe printcartridge is geplaatst. 1. Als u papier in de handinvoer hebt geplaatst, verwijdert u dit en sluit u de handinvoer.
• Plaats de oude printcartridge op papier of gelijksoortig materiaal om uw werkruimte niet vuil te maken. 4. Haal de nieuwe printcartridge uit de verpakking en dan uit de plastic zak. CMC081 5. Plaats de printcartridge op een vlakke ondergrond en verwijder vervolgens het beschermvel.
7. Schuif de printcartridge horizontaal naar binnen. Zodra de cartridge niet meer verder kan, tilt u deze enigszins omhoog en drukt u deze volledig naar binnen. Duw de cartridge omlaag totdat deze vastklikt. CVW026 8. Duw de voorklep voorzichtig omhoog totdat deze sluit.
.
De wrijvingsstrip en de papierinvoerrol schoonmaken 1. Zet het apparaat uit. 2. Trek de stekker uit het stopcontact. Verwijder alle kabels uit het apparaat. 3. Trek lade 1 er voorzichtig met beide handen uit. CVW039 Plaats de lade op een vlak oppervlak.
5. Veeg het rubberen deel van de rol schoon met een zachte, vochtige doek. Droog de wrijvingsstrip vervolgens met een droge doek. CVW040 6. Plaats het verwijderde papier terug in de lade en duw de lade voorzichtig in het apparaat totdat deze op zijn plaats klikt.
.
10. Problemen oplossen Algemene problemen In dit onderdeel wordt beschreven hoe u algemene problemen kunt oplossen die kunnen optreden bij de bediening van dit apparaat. Probleem Mogelijke oorzaak Oplossing Het apparaat kan niet worden aangezet. De stroomkabel is niet op de juiste wijze aangesloten.
.
.
Probleem Oplossing Er worden meerdere vellen papier tegelijkertijd doorgevoerd. • Waaier het papier los voordat u het plaatst. Zorg er ook voor dat de randen gelijk zijn door de stapel op een vlakke ondergrond zoals een bureau te tikken. • Zorg ervoor dat de papiergeleiders in de juiste positie staan.
Een papierstoring verwijderen • Vastgelopen papier kan natte toner bevatten. Let erop dat u geen toner op uw handen en kleding krijgt. • Bij afdrukken die direct na het oplossen van een papierstoring worden gemaakt, kan de toner onvoldoende zijn gefuseerd en gaan vlekken.
5. Druk op de knop aan de zijkant om de klep aan de voorzijde te openen. Breng de klep daarna voorzichtig omlaag. CVW023 6. Til de printercartridge er voorzichtig horizontaal uit, terwijl u deze in het midden vasthoudt. CVW024 • Schud de verwijderde printcartridge niet.
8. Schuif de printcartridge horizontaal naar binnen. Zodra de cartridge niet meer verder kan, tilt u deze enigszins omhoog en drukt u deze volledig naar binnen. Duw de cartridge omlaag totdat deze vastklikt. CVW026 9. Duw met beide handen het voorpaneel voorzichtig omhoog totdat deze sluit.
3. Druk op de knop aan de zijkant om de klep aan de voorzijde te openen. Breng de klep daarna voorzichtig omlaag. CVW023 4. Til de printercartridge er voorzichtig horizontaal uit, terwijl u deze in het midden vasthoudt. CVW024 • Schud de verwijderde printcartridge niet.
6. Schuif de printcartridge horizontaal naar binnen. Zodra de cartridge niet meer verder kan, tilt u deze enigszins omhoog en drukt u deze volledig naar binnen. Duw de cartridge omlaag totdat deze vastklikt. CVW026 7. Duw met beide handen het voorpaneel voorzichtig omhoog totdat deze sluit.
2. Verwijder het vastgelopen papier zorgvuldig. CVW053 3. Sluit de achterklep. CVW017 4. Trek lade 1 half uit en controleer of u vastgelopen papier ziet.
.
.
.
1. Open het ADF-paneel. CVW054 2. Trek voorzichtig aan het vastgelopen origineel om het te verwijderen. Verwijder het vastgelopen origineel niet met te veel kracht. CVW055 3. Sluit het ADF-paneel. 4. Til de ADF op en trek voorzichtig aan het vastgelopen origineel om het te verwijderen.
Problemen met afdrukkwaliteit De toestand van het apparaat controleren Als er een probleem is met de afdrukkwaliteit, controleer dan eerst de toestand van het apparaat. Mogelijke oorzaak Oplossing Er is een probleem met de locatie van het apparaat. Zorg ervoor dat het apparaat op een vlakke ondergrond staat.
.
Probleem Oplossing De gehele afdruk is vaag. • Het papier is vochtig. Gebruik papier dat op de juiste wijze is bewaard. Zie Pag.37 "Ondersteund papier". • Als u [Toner besparen] activeert, worden de afdrukken over het algemeen lichter. • Toner is bijna op.
.
Kopieerproblemen Probleem Oplossing Gekopieerde pagina's bevinden zich niet in de juiste volgorde. Wijzig op het bedieningspaneel de instelling [Sorteren] onder Kopieerinstellingen om de pagina's te sorteren zoals u dat wenst. Voor meer informatie over [Sorteren], zie Pag.
.
Scanproblemen Probleem Oplossing Het apparaat begint niet met scannen. De ADF of de ADF-klep staat open. Sluit de ADF of ADF-klep. De gescande afbeelding is vuil. • De glasplaat of ADF is vies. Zie Pag.213 "Het apparaat onderhouden". • Voordat u originelen op de glasplaat legt, moet de toner of correctievloeistof droog te zijn.
Faxproblemen Als er een foutcode op het faxjournaal of het verzendingsstatusrapport wordt weergegeven De tabel hieronder geeft de betekenis van de foutcodes die onder "Resultaten" op het faxjournaal of het verzendingsstatusrapport kunnen worden weergegeven, en wat u kunt doen als er een bepaalde foutcode wordt weergegeven.
.
Foutcode Oplossing 2XXX32 t/m 2XXX84 Er is een fout opgetreden tijdens het ontvangen van een fax. • Controleer of de telefoonkabel correct op het apparaat is aangesloten. • Haal de telefoonlijn los van het apparaat en sluit een standaard telefoon aan.
Probleem Oplossing Kan ontvangen faxen niet afdrukken. • De papierlade is leeg. Plaats papier in de papierlade. Zie Pag.43 "Papier plaatsen". • De papierlade bevat geen papier van het juiste formaat. Plaats papier met het juiste formaat in de papierlade.
.
.
.
Meldingen Oorzaken Oplossing Max e-mailform overschr. Het scanbestand is groter dan maximaal is toegestaan voor bestanden die via e-mail kunnen worden verstuurd. • Configureer [Resolutie] onder scaninstellingen om de scanresolutie te verlagen. Zie Pag.
Meldingen Oorzaken Oplossing Geheugenoverloop De gegevens zijn te groot of te moeilijk om af te drukken. • Selecteer [600 × 600 dpi] in [Resolutie] onder [Printereigenschappen] om de grootte van de gegevens te verkleinen. Zie Pag.163 "Instellingen voor printereigenschappen".
Meldingen Oorzaken Oplossing Pap.storing: Duplex Verwijder papier Er is papier vastgelopen in de duplexeenheid. Verwijder het vastgelopen papier. Zie Pag.223 "Problemen met papierinvoer". Storing: Stnrd lade Er is papier vastgelopen in de papieruitgang.
Meldingen Oorzaken Oplossing Vervanging vereist: Fuseereenheid De fuseereenheid is niet langer te gebruiken en moet worden vervangen. Neem contact op met uw verkoopvertegenwoordiger. Vervanging vereist: Papierinvoerroller De papierinvoerroller is niet langer te gebruiken en moet worden vervangen.
Meldingen Oorzaken Oplossing Serviceoproep - X Er is een fatale hardwarefout opgetreden en het apparaat werkt niet meer. Neem contact op met uw verkoopvertegenwoordiger. Plaats juist papier De papierlade bevat geen papier met formaat A4, Letter of Legal.
Meldingen Oorzaken Oplossing TX-opdrachtfout Er is een verzendingsfout opgetreden en de fax kon niet correct worden verstuurd. Als de [Autom. opnieuw proberen]- instelling is ingeschakeld, zal het apparaat het nummer opnieuw kiezen.
Ein wichtiger Punkt beim Kauf des Geräts Ricoh SP 204SFN (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Ricoh SP 204SFN noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Ricoh SP 204SFN - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Ricoh SP 204SFN reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Ricoh SP 204SFN erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Ricoh SP 204SFN besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Ricoh SP 204SFN verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Ricoh SP 204SFN. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Ricoh SP 204SFN gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
