Benutzeranleitung / Produktwartung H8S/2168 des Produzenten Renesas
Zur Seite of 27
2003.12.25 H8S/2168 Group TFP-144 User System Interface Cable for E6000 Emulator HS2168ECN61H User’s Manual Renesas Microcomputer Develo pment Environment System H8S Family / H8S/2100 Series Rev.
i Preface Thank you for purchasing this user system interface cable (HS2168ECN61H) for the Renesas’ original mi crocomputer H8S/2168 group. The HS2168ECN61H is a user system interf ace cable that co.
ii Contents Section 1 Configuration .................................................................................... 1 Section 2 Connection Procedures ...................................................................... 3 2.1 Connecting User System Interf ace Cable to Em ulat or Station .
1 Section 1 Configuration CAUTION Use an NQPACK144SE socket (manufactured by Tokyo Eletech Corporation) for the TFP-144 package IC socket on the user system. Figure 1 shows the configuration of the HS2168E CN61H user system interface cable for the TFP-144 package.
2 Table 1 lists t he HS2168ECN61H components. Please m ake sure you have all of these com ponents when unpacking. Table 1 HS2168ECN61H Components No. Component Quantity Remarks 1 Cable body 1 Includes.
3 Section 2 Connection Procedures 2.1 Connecting User System Interface Cable to Emulator Station W ARNING Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and w ill damage the user system and the emulator product or will result in PERSONAL INJURY.
4 2.1.1 Connecting User System Interfa ce Cable to Cable Body Connector After maki ng sure the direction of the cable body connect or is correct, firml y insert the cable body connector into the emulator sta tion socket , and fasten the emulator st ation with two CTS screws (M3 × 6 mm ) (figure 2).
5 2.1.2 Connecting EIO Board 2 to Emul ator 1. Remove four screws at t he side of the emulator stat ion. 2. Pull up and remove t he cover of the emulator casing. 3. Insert connector P5 of EIO board 2 into connector P5 in the em ulator stati on. 4. Fasten EIO board 2 with the provided two screws (M 2.
6 2.1.3 Removing EIO Board 2 from Emulator 1. Remove four screws from the side of the emul ator station. 2. Pull up and remove t he cover of the emulator casing. 3. Remove t wo screws (M2.6 × 6 mm ) from EIO board 2. 4. Remove EIO board 2 from connector P5 of the emul ator station.
7 2.2 Connecting User System Interface Cable to User System W ARNING Always switch OFF the user system and the emulator product before the USER SYSTEM INTERFACE CABLE is connected to or removed from any part. Before connecting, make sure that pin 1 on both sides are correctly aligned.
8 Use the guide pins provided to determ ine where to install t he IC socket, as shown in figure 4. User system IC socket (NQPACK144SE manufactured by Tokyo Eletech Corporation) Guide pins 4 projections to apply epoxy resin adhesive to Bottom view of IC socket Pin 1 Figure 4 Location Setting of IC Socket 2.
9 2.2.3 Inserting Cable Head CAUTION Check the location of pin 1 before inserting. Align pin 1 on the IC socket for a TFP-144 package on the user syst em with pin 1 on the user system interface cable head, and insert the user system interface cable head into the IC socket on the user system, as shown in fi gure 5.
10 Fasten the user system interface cable head to the IC socket for a TFP-144 package on the user system wit h the four screws (M2.0 × 10 m m ) provided. Each screw should be tightened a little at a time, alternating between screws on opposi ng corners.
11 2.2.5 Fastening Cable Body Connect the cable body and EIO board 1 to t he cable head. Cable head Remove jig EIO board 1 EIO board 1 User system Push the lower part of EIO board 1 with your fingers Cable body Cable body Removing Figure 6 Fastening Cable Body and EIO Board 1 When removing the cable body or EIO board 1, push the unfastening jigs.
12 2.3 Recommended Dimensions for User System Mount Pad Figure 7 shows t he recomm ended dim ensions for the mount pad (footprint) for the user system with an IC socket for a TFP-144 package (NQPACK144SE: m anufactured by Tokyo Eletech Corporation).
13 2.4 Dimensions for User System Interface Cable Head The dimensions for the user system inte rface cable head are shown in figure 8. Unit: mm Tolerance: ± 0.
14 2.5 Resulting Dimensions after Connecting User System Interface Cable The resulting dimensions, after conn ecting the user system interface cab le head to the user system, are shown in figure 9. Cable head User system Unit: mm Tolerance: ± 0.5 mm IC socket (NQPACK144SE manufactured by Tokyo Eletech Corporation) 13.
15 Section 3 Installing the MCU on the User System CAUTION 1. Check the location of pin 1 before inserting. 2. Use a screwdriver w hose head matches the screw head.
16 MCU Pin 1 IC socket (NQPACK144SE manufactured by Tokyo Eletech Corporation) User system Screws (M2.0 x 6 mm) Socket cover Figure 10 Installing MCU to User System.
17 Section 4 User System Interface Circuit The microcom puter (H8S/2168) is installed in this user system interface cable for em ulating the LPC function. An interface circuit, as shown in fi gure 11, is provided for the user system interface signal of the H8S/2168.
18 Table 2 Settings of Switches Sw itch Number Pin 1 Side Pin 3 Side SW1 Port E7 SERIRQ SW2 Port E6 LCLK SW3 Port E5 LRESET_N SW4 Port E4 LFRAME_N SW5 Port E3 LAD3 SW6 Port E2 LAD2 SW7 Port E1 LAD1 SW.
19 Section 5 Verifying Operation 1. When using the E6000 emulator for the H8S/ 2168 group, turn on the emulator according to the procedures described in the H8S/2168 Group E6000 Em ulator User's Manual (HS2168EPI61HE).
20 Section 6 Notice 1. Make sure that pin 1 on t he user system IC socket i s correctly aligned wit h pin 1 on the cable head before inserting the cable head into the user system IC socket. 2. The dimensions of t he recommended m ount pad for the user system IC socket are different from those of the MCU.
21 6. To prevent EMI noise, enclose the user system interface cable head in a case. The recommended material of the case is iron plated with nickel or resin plated with nickel inside. The case must be large enough to include the user system interf ace cable head, user system interface cable, and target system.
Cautions Keep safety first in your circuit designs! 1. Renesas Technol ogy Corpo ration puts the maxim um effort into m aking sem iconductor products better and more reliable, but there is always the possibility th at trouble may occur with them. Trouble with semiconductors may lead to personal injury, fire or property damage.
H8S/2168 Group TFP-144 User System Interface Cable for E6000 Emulator User's Manual Publication Date: Rev.1.00, August 25, 2003 Rev.2.00, December 25, 2003 Published by: Sales Strategic Planning Div. Renesas Technology Corp. Edited by: Technical Documentation & Information Department Renesas Kodaira Semiconductor Co.
H8S/2168 Group TFP-144 User System Interface Cable for E6000 Emulator User’s Manual REJ11Jxxxx-x xxxx.
Ein wichtiger Punkt beim Kauf des Geräts Renesas H8S/2168 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Renesas H8S/2168 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Renesas H8S/2168 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Renesas H8S/2168 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Renesas H8S/2168 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Renesas H8S/2168 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Renesas H8S/2168 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Renesas H8S/2168. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Renesas H8S/2168 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
