Benutzeranleitung / Produktwartung HZ54 des Produzenten Regency
Zur Seite of 48
W ARNING: If the information in these instructions are not followed exactly , a fi re or explosion may result causing property damage, personal injury or loss of life. FOR YOUR SAFETY Do not store or use gasoline or other fl ammable vapors and liquids in the vicinity of this or any other appliance.
HZ54 Regency Horizon TM Gas Fireplace 2 T o the New Owner: Congratulations! Y ou are the owner of a state-of-the-art Gas Fireplace by REGENCY ® . The HZ54 has been designed to provide you with all the warmth and charm of a wood fi replace at the fl ick of a switch.
HZ54 Regency Horizon TM Gas Fireplace 3 T ABLE OF CONTENTS SAFETY LABEL Copy of Safety Decal ..................................................... 4 REQUIREMENTS MA Code - CO Detector................................................. 5 DIMENSIONS Unit Dimensions .
HZ54 Regency Horizon TM Gas Fireplace 4 INST ALLA TION SAFETY LABEL This is a copy of the label that accompanies each HZ54-NG and HZ54-LP Direct V ent Gas Fireplace. We have printed a copy of the contents here for your review . NOTE: Regency ® units are constantly being improved.
HZ54 Regency Horizon TM Gas Fireplace 5 INST ALLA TION REQUIREMENTS 5.08: Modifica tions to NFPA-54, Chapter 10 (2) Revise 10.8. 3 by adding the follow ing additiona l requirements: (a) For all side w.
HZ54 Regency Horizon TM Gas Fireplace 6 INST ALLA TION DIMENSIONS F ACEPLA TE & DOOR FRAME OVERLA Y DIMENSIONS UNIT DIMENSIONS.
HZ54 Regency Horizon TM Gas Fireplace 7 INST ALLA TION 10) Be aware of electrical wiring locations in walls and ceilings when cutting holes for termina- tion. 11 ) Under no circumstances should this appliance be modi fi ed. Parts that have to be removed for servicing should be replaced prior to operating this appliance.
HZ54 Regency Horizon TM Gas Fireplace 8 INST ALLA TION INST ALLA TION This includes: 1) Clocking the appliance to ensure the correct firing rate (rate noted on label 41,500 Btu/h (NG), after burning appliance for 15 minutes. 2) If required, adjusting the primary air to ensure that the fl ame does not carbon.
HZ54 Regency Horizon TM Gas Fireplace 9 INST ALLA TION INST ALLA TION Caution Requirements The top, back and sides of the fi replace are de fi ned by standoffs.
HZ54 Regency Horizon TM Gas Fireplace 10 INST ALLA TION INST ALLA TION MANTEL CLEARANCES Note: Ensure the paint that is used on the mantel and the facing is "heat resistant" or the paint may discolour .
HZ54 Regency Horizon TM Gas Fireplace 11 INST ALLA TION INST ALLA TION Note: When constructing the framed opening, please ensure there is access to install the gas lines when the unit is installed.
HZ54 Regency Horizon TM Gas Fireplace 12 INST ALLA TION Framing Dimensions Description HZ54 A Framing Height 46-5/8” (1 184mm) B Framing Width 60” (1524mm) C * Framing Depth * 22” (559mm) D Mini.
HZ54 Regency Horizon TM Gas Fireplace 13 INST ALLA TION SIDE NAILING STRIPS The side and top nailing strips come attached to the unit. There is 1 plate on each side, and 1 on the top, that can be folded out as required.
HZ54 Regency Horizon TM Gas Fireplace 14 INST ALLA TION INST ALLA TION V ent restriction is required for certain venting installations, see the diagrams in the "Venting Arrangements" section to determine if they are required for your installation.
HZ54 Regency Horizon TM Gas Fireplace 15 INST ALLA TION EXTERIOR VENT TERMINA TION REQUIREMENTS INST ALLA TION A= Clearance above grade, veranda, porch, deck, or balcony *(min. 12"/30cm) B= Clearance to window or door that may be opened *(12"/30cm) #(9"/23cm) C= Clearance to permanently closed window *(min.
HZ54 Regency Horizon TM Gas Fireplace 16 INST ALLA TION INST ALLA TION VENTING ARRANGEMENTS HORIZONT AL TERMINA TION (FLEX) Regency ® Direct V ent System These venting systems, in combination with the HZ54, have been tested and listed as a direct vent system by W arnock Hersey/Inte rtek.
HZ54 Regency Horizon TM Gas Fireplace 17 INST ALLA TION RIGID PIPE VENTING SYSTEMS BASIC HORIZONT AL & VERTICAL TERMINA TIONS Rigid Pipe V ent Systems offer a complete line of component parts for installation of both horizontal and vertical installations.
HZ54 Regency Horizon TM Gas Fireplace 18 INST ALLA TION INST ALLA TION 5” X 8” RIGID PIPE CROSS REFERENCE CHART Components from different Manufacturers may not be mixed.
HZ54 Regency Horizon TM Gas Fireplace 19 INST ALLA TION INST ALLA TION.
HZ54 Regency Horizon TM Gas Fireplace 20 INST ALLA TION VENTING ARRANGEMENTS ALLOW ABLE HORIZONT AL TERMINA TIONS FOR HZ54-NG The diagram shows all allowable combinations of vertical runs with horizontal terminations, using one 90 o (two 45 o elbows equal one 90 o elbow).
HZ54 Regency Horizon TM Gas Fireplace 21 INST ALLA TION VENTING ARRANGEMENTS ALLOW ABLE HORIZONT AL TERMINA TIONS FOR HZ54-LP The diagram shows all allowable combinations of vertical runs with horizontal terminations, using one 90 o (two 45 o elbows equal one 90 o elbow).
HZ54 Regency Horizon TM Gas Fireplace 22 INST ALLA TION Horizontal V enting with T wo (2) 90 o Elbows NG and LP Horizontal V enting with Three (3) 90 o Elbows NG and LP One 90 o elbow = T wo 45 o elbows. Option V H + H1 A) 2' Min. 4' Max. B) 3' Min.
HZ54 Regency Horizon TM Gas Fireplace 23 INST ALLA TION V ertical V enting with Three (3) 90 o Elbows NG and LP INST ALLA TION Option V H + H1 V + V1 A) 2' Min. 2' Max. 4' Min. B) 3' Min. 4' Max. 6' Min. C) 4' Min. 5' Max.
HZ54 Regency Horizon TM Gas Fireplace 24 INST ALLA TION • V ent must be supported at offsets. • Firestops are required at each fl oor level and whenever passing through a wall. • Maintain clearances to combustibles as listed in the "Clearances" section.
HZ54 Regency Horizon TM Gas Fireplace 25 INST ALLA TION • V ent must be supported at offsets. • Firestops are required at each fl oor level and whenever passing through a wall. • Maintain clearances to combustibles as listed in the "Clearances" section.
HZ54 Regency Horizon TM Gas Fireplace 26 INST ALLA TION INST ALLA TION Diagram 7 Diagram 5 7) Ensure that the pipe clearances to combustible materials are maintained (Diagram 5).
HZ54 Regency Horizon TM Gas Fireplace 27 INST ALLA TION INST ALLA TION 6) Continue to assemble pipe lengths. Note: If an offset is necessary in the attic to avoid obstructions, it is important to support the vent pipe every 3 feet (0.9 meter), to avoid excessive stress on the elbows, and possible separation.
HZ54 Regency Horizon TM Gas Fireplace 28 INST ALLA TION INST ALLA TION 4) Separate the 2 halves of the wall thimble and securely fasten the one with the tabs to the outside wall making sure that the tabs are on top and bottom. Fasten the other thimble half to the inside wall.
HZ54 Regency Horizon TM Gas Fireplace 29 INST ALLA TION GAS PIPE PRESSURE TESTING The appliance must be isolated from the gas supply piping system by closing its individual manual shut-off valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psig.
HZ54 Regency Horizon TM Gas Fireplace 30 INST ALLA TION WIRING DIAGRAM AERA TION ADJUSTMENT The burner aeration is factory set but may need adjusting due to either the local gas supply or altitude. Open the air shutter for a blue fl ame or close for a more yellow fl ame.
HZ54 Regency Horizon TM Gas Fireplace 31 INST ALLA TION INST ALLA TION Optional W ALL SWITCH (Included with Unit) 1) Run the supplied 10' of wire through the right or left side gas inlet opening.
HZ54 Regency Horizon TM Gas Fireplace 32 INST ALLA TION INST ALLA TION GT REMOTE WIRING DIAGRAM Red wire Black wire Green wire Extra wires not used White wire spade connectors J-Box Receiver Wall Plat.
HZ54 Regency Horizon TM Gas Fireplace 33 INST ALLA TION INST ALLA TION OPTIONAL ST AINLESS STEEL REFLECTIVE P ANEL INST ALLA TION 1) Position the left side panel in place and fi t the bottom tab into the slot at the bottom of the fi rebox as shown below .
HZ54 Regency Horizon TM Gas Fireplace 34 INST ALLA TION INST ALLA TION GLASS CR YST ALS OR OPTIONAL CERAMIC ST ONES INST ALLA TION ON BURNER Evenly spread an appropriate amount of glass crystals or glass crystals plus optional ceramic stones over the burner .
HZ54 Regency Horizon TM Gas Fireplace 35 INST ALLA TION F ACEPLA TE & DOOR FRAME OVERLA Y INST ALLA TION 1) Install the door frame overlay by hooking the top fl ange over top of the glass door , push in the bottom of the door frame overlay to secure in place.
HZ54 Regency Horizon TM Gas Fireplace 36 INST ALLA TION Completed Faceplate & Door Frame Overlay Installation IMPORT ANT NOTE T o ensure the gap between the door frame and the faceplate are equal from side to side you may need to slide the faceplate slightly to the left or right accordingly .
HZ54 Regency Horizon TM Gas Fireplace 37 OPERA TION OPERA TING INSTRUCTIONS 1) Read and understand these instructions before operating this appliance. 2) Check to see that all wiring is correct and enclosed to prevent possible shock. 3) Check to ensure there are no gas leaks.
HZ54 Regency Horizon TM Gas Fireplace 38 OPERA TION OPERA TING INSTRUCTIONS COPY OF LIGHTING PLA TE INSTRUCTIONS TO TURN OFF GAS APPLIANCE FOR YOUR SAFETY READ BEFORE LIGHTING LIGHTING INSTRUCTIONS 1) Push in gas control knob slightly and turn clockwise to “OFF”.
HZ54 Regency Horizon TM Gas Fireplace 39 MAINTENANCE MAINTENANCE MAINTENANCE INSTRUCTIONS 1) Always turn off the gas valve before cleaning. For relighting, refer to lighting instructions. Keep the burner and control compartment clean by brushing and vacuuming at least once a year .
HZ54 Regency Horizon TM Gas Fireplace 40 MAINTENANCE GLASS DOOR REMOV AL 1) T urn the unit off and allow it to cool down to room temperature. 2) T urn off the gas supply to the unit. 3) Remove the faceplate by lifting it up off the hinges on the sides of the fi rebox.
HZ54 Regency Horizon TM Gas Fireplace 41 MAINTENANCE MAINTENANCE DC SP ARK BOX REPLACEMENT 1) Remove the faceplate by lifting it up of f the hinges on the sides of the fi rebox. 2) Remove the door frame overlay by swinging out 45 o from the bottom and lift up and out.
HZ54 Regency Horizon TM Gas Fireplace 42 MAINTENANCE V AL VE TRA Y REPLACEMENT MAINTENANCE 1) T urn the unit off and allow it to cool down to room temperature. 2) T urn off the gas supply to the unit. 3) Remove the faceplate by lifting it up off the hinges on the sides of the fi rebox.
HZ54 Regency Horizon TM Gas Fireplace 43 MAINTENANCE 6) Remove the burner tray by undoing the 2 screws inbetween the bot- tom cover and burner on the fi rebox. Carefully lift the burner up and out ensuring not to spill the glass crystals. Aerial View of the inside of the unit shown.
HZ54 Regency Horizon TM Gas Fireplace 44 MAINTENANCE INSTRUCTIONS BELOW FOR HZ54-LP UNIT ONL Y . 6) Loosen 6 screws that secure the burner extenders. on burner tray , located behind the burner on either side of the pilot assembly . 7) Lift out the 2 burner tray extenders.
HZ54 Regency Horizon TM Gas Fireplace 45 P AR TS LIST P ARTS LIST MAIN ASSEMBL Y 1 4 5 6 8 3 7 2 9 Part # Description 1) 910-074 Spark Generator Switch c/w Wire 2) 476-032 DC Spark Mounting Bracket 91.
HZ54 Regency Horizon TM Gas Fireplace 46 P AR TS LIST Part # Description 30) 476-907 Re fl ective Stainless Steel Panels 31) 476-914 Faceplate & Door Frame Overlay - Black 476-917 Faceplate &.
HZ54 Regency Horizon TM Gas Fireplace 47 W ARRANTY Regency ® Fireplace Products are designed with reliability and simplicity in mind. In addition, our internal Quality Assurance T eam carefully inspects each unit thoroughly before it leaves our facility .
HZ54 Regency Horizon TM Gas Fireplace 48 Installer: Please complete the following information Dealer Name & Address: ______________________________________________ ________________________________.
Ein wichtiger Punkt beim Kauf des Geräts Regency HZ54 (oder sogar vor seinem Kauf) ist das durchlesen seiner Bedienungsanleitung. Dies sollten wir wegen ein paar einfacher Gründe machen:
Wenn Sie Regency HZ54 noch nicht gekauft haben, ist jetzt ein guter Moment, um sich mit den grundliegenden Daten des Produkts bekannt zu machen. Schauen Sie zuerst die ersten Seiten der Anleitung durch, die Sie oben finden. Dort finden Sie die wichtigsten technischen Daten für Regency HZ54 - auf diese Weise prüfen Sie, ob das Gerät Ihren Wünschen entspricht. Wenn Sie tiefer in die Benutzeranleitung von Regency HZ54 reinschauen, lernen Sie alle zugänglichen Produktfunktionen kennen, sowie erhalten Informationen über die Nutzung. Die Informationen, die Sie über Regency HZ54 erhalten, werden Ihnen bestimmt bei der Kaufentscheidung helfen.
Wenn Sie aber schon Regency HZ54 besitzen, und noch keine Gelegenheit dazu hatten, die Bedienungsanleitung zu lesen, sollten Sie es aufgrund der oben beschriebenen Gründe machen. Sie erfahren dann, ob Sie die zugänglichen Funktionen richtig genutzt haben, aber auch, ob Sie keine Fehler begangen haben, die den Nutzungszeitraum von Regency HZ54 verkürzen könnten.
Jedoch ist die eine der wichtigsten Rollen, die eine Bedienungsanleitung für den Nutzer spielt, die Hilfe bei der Lösung von Problemen mit Regency HZ54. Sie finden dort fast immer Troubleshooting, also die am häufigsten auftauchenden Störungen und Mängel bei Regency HZ54 gemeinsam mit Hinweisen bezüglich der Arten ihrer Lösung. Sogar wenn es Ihnen nicht gelingen sollte das Problem alleine zu bewältigen, die Anleitung zeigt Ihnen die weitere Vorgehensweise – den Kontakt zur Kundenberatung oder dem naheliegenden Service.
